aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* check-toolchain-clean.sh: fix shellcheck warningsPetr Štetiar2022-02-281-1/+1
| | | | | | | | | | | Fixes following complaints and suggestions: In scripts/check-toolchain-clean.sh line 2: eval `grep CONFIG_GCC_VERSION .config` ^-- SC2046 (warning): Quote this to prevent word splitting. ^-- SC2006 (style): Use $(...) notation instead of legacy backticks `...`. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: bump to git HEADStijn Tintel2022-02-281-3/+3
| | | | | | 002cfaf firmware-utils: fix compilation with macOS Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* netfilter: add kmod-nft-tproxyYousong Zhou2022-02-282-0/+13
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* netfilter: add kmod-nft-socketYousong Zhou2022-02-282-0/+13
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxyYousong Zhou2022-02-282-7/+45
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ath79: add support for TP-Link Archer A9 v6Piotr Dymacz2022-02-274-0/+265
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer A9 v6 (FCCID: TE7A9V6) is an AC1900 Wave-2 gigabit home router based on a combination of Qualcomm QCN5502 (most likely a 4x4:4 version of the QCA9563 WiSOC), QCA9984 and QCA8337N. The vendor's firmware content reveals that the same device might be available on the US market under name 'Archer C90 v6'. Due to lack of access to such hardware, support introduced in this commit was tested only on the EU version (sold under 'Archer A9 v6' name). Based on the information on the PL version of the vendor website, this device has been already phased out and is no longer available. Specifications: - Qualcomm QCN5502 (775 MHz) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 5x Gbps Ethernet (Qualcomm QCA8337N over SGMII) - Wi-Fi: - 802.11b/g/n on 2.4 GHz: Qualcomm QCN5502* in 4x4:4 mode - 802.11a/n/ac on 5 GHz: Qualcomm QCA9984 in 3x3:3 mode - 3x non-detachable, dual-band external antennas (~3.5 dBi for 5 GHz, ~2.2 dBi for 2.4 GHz, IPEX/U.FL connectors) - 1x internal PCB antenna for 2.4 GHz (~1.8 dBi) - 1x USB 2.0 Type-A - 11x LED (4x connected to QCA8337N, 7x connected to QCN5502) - 2x button (reset, WPS) - UART (4-pin, 2.54 mm pitch) header on PCB (not populated) - 1x mechanical power switch - 1x DC jack (12 V) *) unsupported due to missing support for QCN550x in ath9k UART system serial console notice: The RX signal of the main SOC's UART on this device is shared with the WPS button's GPIO. The first-stage U-Boot by default disables the RX, resulting in a non-functional UART input. If you press and keep 'ENTER' on the serial console during early boot-up, the first-stage U-Boot will enable RX input. Vendor firmware allows password-less access to the system over serial. Flash instruction (vendor GUI): 1. It is recommended to first upgrade vendor firmware to the latest version (1.1.1 Build 20210315 rel.40637 at the time of writing). 2. Use the 'factory' image directly in the vendor's GUI. Flash instruction (TFTP based recovery in second-stage U-Boot): 1. Rename 'factory' image to 'ArcherA9v6_tp_recovery.bin' 2. Setup a TFTP server on your PC with IP 192.168.0.66/24. 3. Press and hold the reset button for ~5 sec while turning on power. 4. The device will download image, flash it and reboot. Flash instruction (web based recovery in first-stage U-Boot): 1. Use 'CTRL+C' during power-up to enable CLI in first-stage U-Boot. 2. Connect a PC with IP set to 192.168.0.1 to one of the LAN ports. 3. Issue 'httpd' command and visit http://192.168.0.1 in browser. 4. Use the 'factory' image. If you would like to restore vendor's firmware, follow one of the recovery methods described above. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: ath79: add support for ALFA Network Tube-2HQPiotr Dymacz2022-02-271-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for ALFA Network Tube-2HQPiotr Dymacz2022-02-274-0/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-2HQ is a successor of the Tube-2H/P series (EOL) which was based on the Atheros AR9331. The new version uses Qualcomm QCA9531. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 64 or 128 MB of RAM (DDR2) - 16+ MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) (802.3at/af PoE support with optional module) - 1T1R 2.4 GHz Wi-Fi with external PA (SE2623L, up to 27 dBm) and LNA - 1x Type-N (male) antenna connector - 6x LED (5x driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - UART (4-pin, 2.00 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: utilize ath9k 'nvmem-cells' on ALFA Network boardsPiotr Dymacz2022-02-273-30/+49
| | | | | | | Drop custom 'mtd-cal-data' and switch to 'nvmem-cells' based solution for fetching radio calibration data and its MAC address. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: reduce 'nvmem-cells' definitions on ALFA Network QCA9531 boardsPiotr Dymacz2022-02-274-30/+8
| | | | | | | | | | All the QCA9531 based boards from ALFA Network are based on the same design and share a common DTSI: 'qca9531_alfa-network_r36a.dtsi'. Instead of defining 'nvmem-cells' for the MAC address in every device's DTS, move definition to the common DTSI file. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* bcm63xx: switch to Kernel 5.10Paul Spooren2022-02-271-2/+2
| | | | | | | | Bump the last missing target to Kernel 5.10. While this requires a work around to boot it will allow more people to test the new Kernel before the upcomming release. Signed-off-by: Paul Spooren <mail@aparcar.org>
* bcm63xx: fix booting with Kernel 5.10Paul Spooren2022-02-271-0/+18
| | | | | | | | This is a workaround to make the target overall bootable. With this more people should be able to test the Kernel 5.10 and report further issues. Suggested-by: Daniel González Cabanelas <dgcbueu@gmail.com> Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: support TP-Link EAP615-WallStijn Tintel2022-02-273-1/+209
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP. The device is very similar to the TP-Link EAP235-Wall. Hardware: * SoC: MediaTek MT7621AT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Ethernet: 4x GbE * Back: ETH0 (PoE-PD) * Bottom: ETH1, ETH2, ETH3 (PoE passthrough) * WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R * LEDS: 1x white * Buttons: 1x LED, 1x reset Stock firmware uses a random MAC address for ethernet. OpenWrt uses the MAC address that is on the device label for ethernet and the wireless interfaces. MAC address must not be incremented, as this will cause MAC address conflicts in case you have two devices with consecutive MAC addresses. Instead, different locally administered addresses will be generated automatically, based on the MAC on the label. Installation via stock firmware: * Enable SSH in the TP-Link web interface * SSH to the device * Run `cliclientd stopcs` * Upload the OpenWrt factory image via the TP-Link web interface Installation via bootloader: * Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1 closest to ETH1. Baud rate 115200 * Interrupt boot process by holding a key during boot * Boot the OpenWrt initramfs: # tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin # bootm * Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin to /tmp and use sysupgrade to install it Thanks to Sander Vanheule for his work on the EAP235-Wall, which made adding support for the EAP615-Wall very easy. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Sander Vanheule <sander@svanheule.net> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* firmware-utils: bump to git HEADStijn Tintel2022-02-271-3/+3
| | | | | | | | | | | 706e9cc tplink-safeloader: support for Archer A6 v3 JP 497726b firmware-utils: support checksum for AVM fritzbox wasp SOCs 2ca6462 iptime-crc32: add support for AX8004M 57d0e31 tplink-safeloader: TP-Link EAP615-Wall v1 support 8a8da19 tplink-safeloader: add TL-WPA8631P v3 support eea4ee7 tplink-safeloader: add TP-Link Archer A9 v6 support Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* firmware: intel-microcode: update to 20220207Christian Lamparter2022-02-261-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Debians' changelog by Henrique de Moraes Holschuh <hmh@debian.org>: * upstream changelog: new upstream datafile 20220207 * Mitigates (*only* when loaded from UEFI firmware through the FIT) CVE-2021-0146, INTEL-SA-00528: VT-d privilege escalation through debug port, on Pentium, Celeron and Atom processors with signatures 0x506c9, 0x506ca, 0x506f1, 0x706a1, 0x706a8 https://github.com/intel/Intel-Linux-Processor-Microcode-Data-Files/issues/57#issuecomment-1036363145 * Mitigates CVE-2021-0127, INTEL-SA-00532: an unexpected code breakpoint may cause a system hang, on many processors. * Mitigates CVE-2021-0145, INTEL-SA-00561: information disclosure due to improper sanitization of shared resources (fast-store forward predictor), on many processors. * Mitigates CVE-2021-33120, INTEL-SA-00589: out-of-bounds read on some Atom Processors may allow information disclosure or denial of service via network access. * Fixes critical errata (functional issues) on many processors * Adds a MSR switch to enable RAPL filtering (default off, once enabled it can only be disabled by poweroff or reboot). Useful to protect SGX and other threads from side-channel info leak. Improves the mitigation for CVE-2020-8694, CVE-2020-8695, INTEL-SA-00389 on many processors. * Disables TSX in more processor models. * Fixes issue with WBINDV on multi-socket (server) systems which could cause resets and unpredictable system behavior. * Adds a MSR switch to 10th and 11th-gen (Ice Lake, Tiger Lake, Rocket Lake) processors, to control a fix for (hopefully rare) unpredictable processor behavior when HyperThreading is enabled. This MSR switch is enabled by default on *server* processors. On other processors, it needs to be explicitly enabled by an updated UEFI/BIOS (with added configuration logic). An updated operating system kernel might also be able to enable it. When enabled, this fix can impact performance. * Updated Microcodes: sig 0x000306f2, pf_mask 0x6f, 2021-08-11, rev 0x0049, size 38912 sig 0x000306f4, pf_mask 0x80, 2021-05-24, rev 0x001a, size 23552 sig 0x000406e3, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 105472 sig 0x00050653, pf_mask 0x97, 2021-05-26, rev 0x100015c, size 34816 sig 0x00050654, pf_mask 0xb7, 2021-06-16, rev 0x2006c0a, size 43008 sig 0x00050656, pf_mask 0xbf, 2021-08-13, rev 0x400320a, size 35840 sig 0x00050657, pf_mask 0xbf, 2021-08-13, rev 0x500320a, size 36864 sig 0x0005065b, pf_mask 0xbf, 2021-06-04, rev 0x7002402, size 28672 sig 0x00050663, pf_mask 0x10, 2021-06-12, rev 0x700001c, size 28672 sig 0x00050664, pf_mask 0x10, 2021-06-12, rev 0xf00001a, size 27648 sig 0x00050665, pf_mask 0x10, 2021-09-18, rev 0xe000014, size 23552 sig 0x000506c9, pf_mask 0x03, 2021-05-10, rev 0x0046, size 17408 sig 0x000506ca, pf_mask 0x03, 2021-05-10, rev 0x0024, size 16384 sig 0x000506e3, pf_mask 0x36, 2021-04-29, rev 0x00ec, size 108544 sig 0x000506f1, pf_mask 0x01, 2021-05-10, rev 0x0036, size 11264 sig 0x000606a6, pf_mask 0x87, 2021-12-03, rev 0xd000331, size 291840 sig 0x000706a1, pf_mask 0x01, 2021-05-10, rev 0x0038, size 74752 sig 0x000706a8, pf_mask 0x01, 2021-05-10, rev 0x001c, size 75776 sig 0x000706e5, pf_mask 0x80, 2021-05-26, rev 0x00a8, size 110592 sig 0x000806a1, pf_mask 0x10, 2021-09-02, rev 0x002d, size 34816 sig 0x000806c1, pf_mask 0x80, 2021-08-06, rev 0x009a, size 109568 sig 0x000806c2, pf_mask 0xc2, 2021-07-16, rev 0x0022, size 96256 sig 0x000806d1, pf_mask 0xc2, 2021-07-16, rev 0x003c, size 101376 sig 0x000806e9, pf_mask 0x10, 2021-04-28, rev 0x00ec, size 104448 sig 0x000806e9, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 104448 sig 0x000806ea, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 103424 sig 0x000806eb, pf_mask 0xd0, 2021-04-28, rev 0x00ec, size 104448 sig 0x000806ec, pf_mask 0x94, 2021-04-28, rev 0x00ec, size 104448 sig 0x00090661, pf_mask 0x01, 2021-09-21, rev 0x0015, size 20480 sig 0x000906c0, pf_mask 0x01, 2021-08-09, rev 0x2400001f, size 20480 sig 0x000906e9, pf_mask 0x2a, 2021-04-29, rev 0x00ec, size 106496 sig 0x000906ea, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 102400 sig 0x000906eb, pf_mask 0x02, 2021-04-28, rev 0x00ec, size 104448 sig 0x000906ec, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424 sig 0x000906ed, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424 sig 0x000a0652, pf_mask 0x20, 2021-04-28, rev 0x00ec, size 93184 sig 0x000a0653, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 94208 sig 0x000a0655, pf_mask 0x22, 2021-04-28, rev 0x00ee, size 94208 sig 0x000a0660, pf_mask 0x80, 2021-04-28, rev 0x00ea, size 94208 sig 0x000a0661, pf_mask 0x80, 2021-04-29, rev 0x00ec, size 93184 sig 0x000a0671, pf_mask 0x02, 2021-08-29, rev 0x0050, size 102400 * Removed Microcodes: sig 0x00080664, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048 sig 0x00080665, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048 * update .gitignore and debian/.gitignore. Add some missing items from .gitignore and debian/.gitignore. * ucode-blacklist: do not late-load 0x406e3 and 0x506e3. When the BIOS microcode is older than revision 0x7f (and perhaps in some other cases as well), the latest microcode updates for 0x406e3 and 0x506e3 must be applied using the early update method. Otherwise, the system might hang. Also: there must not be any other intermediate microcode update attempts [other than the one done by the BIOS itself], either. It must go from the BIOS microcode update directly to the latest microcode update. * source: update symlinks to reflect id of the latest release, 20220207 Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* iucode-tool: fix host-compile on macos and non-x86 linuxSergey V. Lobanov2022-02-262-1/+45
| | | | | | | | | | | | | | | | | | | | | | | iucode-tool/host is used by intel-microcode to manipulate with microcode.bin file. iucode-tool requires cpuid.h at compile time for autodection feature, but non-x86 build hosts does not have this header file (e.g. ubuntu 20.04 aarch64) or this header generates compile time error (#error macro) (e.g. macos arm64). This patch provides compat cpuid.h to build iucode-tool/host on non-x86 linux hosts and macos. CPU autodectection is not required for intel-microcode package build so compat cpuid.h is ok for OpenWrt purposes. glibc and argp lib are not present in macos so iucode-tool/host build fails. This patch adds argp-standalone/host as build dependency if host os is macos. Generated ucode (intel-microcode package) is exactly the same on Linux x86_64 (Ubuntu 20.04), Linux aarch64 (Ubuntu 20.04) and Darwin arm64 (MacOS 11.6) build hosts. Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
* argp-standalone: add host-compile abilitySergey V. Lobanov2022-02-261-1/+12
| | | | | | | | | This patch adds host-compile ability to argp-standalone for build hosts without glibc and argp lib, e.g. MacOS. iucode-tool/host can not be built on MacOS due to lack of argp. Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
* at91: remove pm debug features from sama5 kernel configClaudiu Beznea2022-02-261-4/+0
| | | | | | | | | | Remove PM debug features from sama5 kernel config. It is not necessary to have it on production code. This also fixes the build for sama5 target after commit 97158fe10e60 ("kernel: package ramoops pstore-ram crash log storage) Fixes: 97158fe10e60 ("kernel: package ramoops pstore-ram crash log storage") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* mbedtls: update to 2.28.0 LTS branchLucian Cristian2022-02-262-24/+28
| | | | | | | | | | | | | | | | | | | | | | | | <https://github.com/ARMmbed/mbedtls/releases/tag/v2.28.0> "Mbed TLS 2.28 is a long-time support branch. It will be supported with bug-fixes and security fixes until end of 2024." <https://github.com/ARMmbed/mbedtls/blob/development/BRANCHES.md> "Currently, the only supported LTS branch is: mbedtls-2.28. For a short time we also have the previous LTS, which has recently ended its support period, mbedtls-2.16. This branch will move into the archive namespace around the time of the next release." this will also add support for uacme ualpn support. size changes 221586 libmbedtls12_2.28.0-1_mips_24kc.ipk 182742 libmbedtls12_2.16.12-1_mips_24kc.ipk Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com> (remark about 2.16's EOS, slightly reworded) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: Increase kernel size to 4 MB for EA8500/EA7500v1Hannu Nyman2022-02-263-9/+27
| | | | | | | | | | | | | | | | | | | Increase the kernel size from 3 MB to 4 MB for EA8500 and EA7500v1. * modify the common .dtsi * modify the kernel size in the image recipes Define compat-version 2.0 to force factory image usage for sysupgrade. Add explanation message. Reenable both devices. As for 4MiB (and not more): Hannu Nyman noted that: "We have lots of ipq806x devices with 4 MB kernel, so will need action at that point in future in any case. (Assuming that the bootloader did not have a 4 MB limit that has been tested...)" Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> (squashed, added 4MiB notice of support in ipq806x) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: support ZTE MF286A/RLech Perczak2022-02-268-202/+409
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZTE MF286A and MF286R are indoor LTE category 6/7 CPE router with simultaneous dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit Ethernet switch, FXS and external USB 2.0 port. Hardware highlights: - CPU: QCA9563 SoC at 775MHz, - RAM: 128MB DDR2, - NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only, - NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data, - Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio, - WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio, - Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port, - WWAN: [MF286A] MDM9230-based category 6 internal LTE modem [MF286R] PXA1826-based category 7 internal LTE modem in extended mini-PCIE form factor, with 3 internal antennas and 2 external antenna connections, single mini-SIM slot. - FXS: one external ATA port (handled entirely by modem part) with two physical connections in parallel, - USB: Single external USB 2.0 port, - Switches: power switch, WPS, Wi-Fi and reset buttons, - LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery, Signal state) handled entirely by modem. 4 link status LEDs handled by the switch on the backside. - Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and monitoring handled by modem. - Label MAC device: eth0 The device shares many components with previous model, MF286, differing mostly by a Wave2 5GHz radio, flash layout and internal LED color. In case of MF286A, the modem is the same as in MF286. MF286R uses a different modem based on Marvell PXA1826 chip. Internal modem of MF286A is supported via uqmi, MF286R modem isn't fully supported, but it is expected to use comgt-ncm for connection, as it uses standard 3GPP AT commands for connection establishment. Console connection: connector X2 is the console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright: - VCC (3.3V). Do not use unless you need to source power for the converer from it. - TX - RX - GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. Installation: Due to different flash layout from stock firmware, sysupgrade from within stock firmware is impossible, despite it's based on QSDK which itself is based on OpenWrt. STEP 0: Stock firmware update: As installing OpenWrt cuts you off from official firmware updates for the modem part, it is recommended to update the stock firmware to latest version before installation, to have built-in modem at the latest firmware version. STEP 1: gaining root shell: Method 1: This works if busybox has telnetd compiled in the binary. If this does not work, try method 2. Using well-known exploit to start telnetd on your router - works only if Busybox on stock firmware has telnetd included: - Open stock firmware web interface - Navigate to "URL filtering" section by going to "Advanced settings", then "Firewall" and finally "URL filter". - Add an entry ending with "&&telnetd&&", for example "http://hostname/&&telnetd&&". - telnetd will immediately listen on port 4719. - After connecting to telnetd use "admin/admin" as credentials. Method 2: This works if busybox does not have telnetd compiled in. Notably, this is the case in DNA.fi firmware. If this does not work, try method 3. - Set IP of your computer to 192.168.0.22. (or appropriate subnet if changed) - Have a TFTP server running at that address - Download MIPS build of busybox including telnetd, for example from: https://busybox.net/downloads/binaries/1.21.1/busybox-mips and put it in it's root directory. Rename it as "telnetd". - As previously, login to router's web UI and navigate to "URL filtering" - Using "Inspect" feature, extend "maxlength" property of the input field named "addURLFilter", so it looks like this: <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332" class="required form-control"> - Stay on the page - do not navigate anywhere - Enter "http://aa&zte_debug.sh 192.168.0.22 telnetd" as a filter. - Save the settings. This will download the telnetd binary over tftp and execute it. You should be able to log in at port 23, using "admin/admin" as credentials. Method 3: If the above doesn't work, use the serial console - it exposes root shell directly without need for login. Some stock firmwares, notably one from finnish DNA operator lack telnetd in their builds. STEP 2: Backing up original software: As the stock firmware may be customized by the carrier and is not officially available in the Internet, IT IS IMPERATIVE to back up the stock firmware, if you ever plan to returning to stock firmware. It is highly recommended to perform backup using both methods, to avoid hassle of reassembling firmware images in future, if a restore is needed. Method 1: after booting OpenWrt initramfs image via TFTP: PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION. - Dump stock firmware located on stock kernel and ubi partitions: ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin ssh root@192.168.1.1: cat /dev/mtd9 > mtd9_ubi.bin And keep them in a safe place, should a restore be needed in future. Method 2: using stock firmware: - Connect an external USB drive formatted with FAT or ext4 to the USB port. - The drive will be auto-mounted to /var/usb_disk - Check the flash layout of the device: cat /proc/mtd It should show the following: mtd0: 000a0000 00010000 "u-boot" mtd1: 00020000 00010000 "u-boot-env" mtd2: 00140000 00010000 "reserved1" mtd3: 000a0000 00020000 "fota-flag" mtd4: 00080000 00020000 "art" mtd5: 00080000 00020000 "mac" mtd6: 000c0000 00020000 "reserved2" mtd7: 00400000 00020000 "cfg-param" mtd8: 00400000 00020000 "log" mtd9: 000a0000 00020000 "oops" mtd10: 00500000 00020000 "reserved3" mtd11: 00800000 00020000 "web" mtd12: 00300000 00020000 "kernel" mtd13: 01a00000 00020000 "rootfs" mtd14: 01900000 00020000 "data" mtd15: 03200000 00020000 "fota" mtd16: 01d00000 00020000 "firmware" Differences might indicate that this is NOT a MF286A device but one of other variants. - Copy over all MTD partitions, for example by executing the following: for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \ /var/usb_disk/mtd$i; done "Firmware" partition can be skipped, it is a concatenation of "kernel" and "rootfs". - If the count of MTD partitions is different, this might indicate that this is not a MF286A device, but one of its other variants. - (optionally) rename the files according to MTD partition names from /proc/mtd - Unmount the filesystem: umount /var/usb_disk; sync and then remove the drive. - Store the files in safe place if you ever plan to return to stock firmware. This is especially important, because stock firmware for this device is not available officially, and is usually customized by the mobile providers. STEP 3: Booting initramfs image: Method 1: using serial console (RECOMMENDED): - Have TFTP server running, exposing the OpenWrt initramfs image, and set your computer's IP address as 192.168.0.22. This is the default expected by U-boot. You may wish to change that, and alter later commands accordingly. - Connect the serial console if you haven't done so already, - Interrupt boot sequence by pressing any key in U-boot when prompted - Use the following commands to boot OpenWrt initramfs through TFTP: setenv serverip 192.168.0.22 setenv ipaddr 192.168.0.1 tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin bootm 0x81000000 (Replace server IP and router IP as needed). There is no emergency TFTP boot sequence triggered by buttons, contrary to MF283+. - When OpenWrt initramfs finishes booting, proceed to actual installation. Method 2: using initramfs image as temporary boot kernel This exploits the fact, that kernel and rootfs MTD devices are consecutive on NAND flash, so from within stock image, an initramfs can be written to this area and booted by U-boot on next reboot, because it uses "nboot" command which isn't limited by kernel partition size. - Download the initramfs-kernel.bin image - After backing up the previous MTD contents, write the images to the "firmware" MTD device, which conveniently concatenates "kernel" and "rootfs" partitions that can fit the initramfs image: nandwrite -p /dev/<firmware-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286a-initramfs-kernel.bin - If write is OK, reboot the device, it will reboot to OpenWrt initramfs: reboot -f - After rebooting, SSH into the device and use sysupgrade to perform proper installation. Method 3: using built-in TFTP recovery (LAST RESORT): - With that method, ensure you have complete backup of system's NAND flash first. It involves deliberately erasing the kernel. - Download "-initramfs-kernel.bin" image for the device. - Prepare the recovery image by prepending 8MB of zeroes to the image, and name it root_uImage: dd if=/dev/zero of=padding.bin bs=8M count=1 cat padding.bin openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin > root_uImage - Set up a TFTP server at 192.0.0.1/8. Router will use random address from that range. - Put the previously generated "root_uImage" into TFTP server root directory. - Deliberately erase "kernel" partition" using stock firmware after taking backup. THIS IS POINT OF NO RETURN. - Restart the device. U-boot will attempt flashing the recovery initramfs image, which will let you perform actual installation using sysupgrade. This might take a considerable time, sometimes the router doesn't establish Ethernet link properly right after booting. Be patient. - After U-boot finishes flashing, the LEDs of switch ports will all light up. At this moment, perform power-on reset, and wait for OpenWrt initramfs to finish booting. Then proceed to actual installation. STEP 4: Actual installation: - Set your computer IP to 192.168.1.22/24 - scp the sysupgrade image to the device: scp openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \ root@192.168.1.1:/tmp/ - ssh into the device and execute sysupgrade: sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin - Wait for router to reboot to full OpenWrt. STEP 5: WAN connection establishment Since the router is equipped with LTE modem as its main WAN interface, it might be useful to connect to the Internet right away after installation. To do so, please put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth '<auth>' # As required, usually 'none' option pincode '<pin>' # If required by SIM option apn '<apn>' # As required by ISP option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6' For example, the following works for most polish ISPs config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option apn 'internet' option pdptype 'ipv4' The required minimum is: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' In this case, the modem will use last configured APN from stock firmware - this should work out of the box, unless your SIM requires PIN which can't be switched off. If you have build with LuCI, installing luci-proto-qmi helps with this task. Restoring the stock firmware: Preparation: If you took your backup using stock firmware, you will need to reassemble the partitions into images to be restored onto the flash. The layout might differ from ISP to ISP, this example is based on generic stock firmware The only partitions you really care about are "web", "kernel", and "rootfs". These are required to restore the stock firmware through factory TFTP recovery. Because kernel partition was enlarged, compared to stock firmware, the kernel and rootfs MTDs don't align anymore, and you need to carve out required data if you only have backup from stock FW: - Prepare kernel image cat mtd12_kernel.bin mtd13_rootfs.bin > owrt_kernel.bin truncate -s 4M owrt_kernel_restore.bin - Cut off first 1MB from rootfs dd if=mtd13_rootfs.bin of=owrt_rootfs.bin bs=1M skip=1 - Prepare image to write to "ubi" meta-partition: cat mtd6_reserved2.bi mtd7_cfg-param.bin mtd8_log.bin mtd9_oops.bin \ mtd10_reserved3.bin mtd11_web.bin owrt_rootfs.bin > \ owrt_ubi_ubi_restore.bin You can skip the "fota" partition altogether, it is used only for stock firmware update purposes and can be overwritten safely anyway. The same is true for "data" partition which on my device was found to be unused at all. Restoring mtd5_cfg-param.bin will restore the stock firmware configuration you had before. Method 1: Using initramfs: This method is recmmended if you took your backup from within OpenWrt initramfs, as the reassembly is not needed. - Boot to initramfs as in step 3: - Completely detach ubi0 partition using ubidetach /dev/ubi0_0 - Look up the kernel and ubi partitions in /proc/mtd - Copy over the stock kernel image using scp to /tmp - Erase kernel and restore stock kernel: (scp mtd4_kernel.bin root@192.168.1.1:/tmp/) mtd write <kernel_mtd> mtd4_kernel.bin rm mtd4_kernel.bin - Copy over the stock partition backups one-by-one using scp to /tmp, and restore them individually. Otherwise you might run out of space in tmpfs: (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin rm mtd3_ubiconcat0.bin (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin rm mtd5_ubiconcat1.bin - If the write was correct, force a device reboot with reboot -f Method 2: Using live OpenWrt system (NOT RECOMMENDED): - Prepare a USB flash drive contatining MTD backup files - Ensure you have kmod-usb-storage and filesystem driver installed for your drive - Mount your flash drive mkdir /tmp/usb mount /dev/sda1 /tmp/usb - Remount your UBI volume at /overlay to R/O mount -o remount,ro /overlay - Write back the kernel and ubi partitions from USB drive cd /tmp/usb mtd write mtd4_kernel.bin /dev/<kernel_mtd> mtd write mtd9_ubi.bin /dev/<kernel_ubi> - If everything went well, force a device reboot with reboot -f Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota" MTD partition which may be safely erased after reboot anyway. Method 3: using built-in TFTP recovery: This method is recommended if you took backups using stock firmware. - Assemble a recovery rootfs image from backup of stock partitions by concatenating "web", "kernel", "rootfs" images dumped from the device, as "root_uImage" - Use it in place of "root_uImage" recovery initramfs image as in the TFTP pre-installation method. Quirks and known issuesa - It was observed, that CH340-based USB-UART converters output garbage during U-boot phase of system boot. At least CP2102 is known to work properly. - Kernel partition size is increased to 4MB compared to stock 3MB, to accomodate future kernel updates - at this moment OpenWrt 5.10 kernel image is at 2.5MB which is dangerously close to the limit. This has no effect on booting the system - but keep that in mind when reassembling an image to restore stock firmware. - uqmi seems to be unable to change APN manually, so please use the one you used before in stock firmware first. If you need to change it, please use protocok '3g' to establish connection once, or use the following command to change APN (and optionally IP type) manually: echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0 - The only usable LED as a "system LED" is the blue debug LED hidden inside the case. All other LEDs are controlled by modem, on which the router part has some influence only on Wi-Fi LED. - Wi-Fi LED currently doesn't work while under OpenWrt, despite having correct GPIO mapping. All other LEDs are controlled by modem, including this one in stock firmware. GPIO19, mapped there only acts as a gate, while the actual signal source seems to be 5GHz Wi-Fi radio, however it seems it is not the LED exposed by ath10k as ath10k-phy0. - GPIO5 used for modem reset is a suicide switch, causing a hardware reset of whole board, not only the modem. It is attached to gpio-restart driver, to restart the modem on reboot as well, to ensure QMI connectivity after reboot, which tends to fail otherwise. - Modem, as in MF283+, exposes root shell over ADB - while not needed for OpenWrt operation at all - have fun lurking around. The same modem module is used as in older MF286. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* tools/meson: update to 0.61.2Rosen Penev2022-02-261-2/+2
| | | | | | Seems to be minor bugfixes with Cygwin and Windows. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* usbmode: update to version 2022-02-24Petr Štetiar2022-02-261-4/+4
| | | | | | * usbmode: add config #0 and delay before actual config Signed-off-by: Petr Štetiar <ynezz@true.cz>
* jsonfilter: update makefile urlVladislav Grigoryev2022-02-261-1/+1
| | | | | | Specify URL as PKG_SOURCE_URL in the jsonfilter Makefile. Signed-off-by: Vladislav Grigoryev <vg.aetera@gmail.com>
* ramips: mt7621-dts: add pinctrl properties for ethernetArınç ÜNAL2022-02-2627-1/+108
| | | | | | | | | | | | | | | Add the missing pinctrl properties on the ethernet node. GMAC1 will start working with this change. Link: https://lore.kernel.org/netdev/83a35aa3-6cb8-2bc4-2ff4-64278bbcd8c8@arinc9.com/ Overwrite pinctrl-0 property without rgmii2_pins on devicetrees which use the rgmii2 pins as GPIO (22 - 33). Give gpio function to rgmii2 pin group on mt7621_tplink_archer-x6-v3.dtsi which uses GPIO 28. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: mt7621-dts: enable flow control on port@6Arınç ÜNAL2022-02-261-0/+1
| | | | | | | | Flow control needs to be enabled on both sides to work. It is already enabled on gmac0, enable it on port@6 too. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7621-dts: fix switch@1f warningsArınç ÜNAL2022-02-261-3/+0
| | | | | | | | | | | | | Remove reg property from ports node to fix this warning: Warning (unit_address_vs_reg): /ethernet@1e100000/mdio-bus/switch@1f/ports: node has a reg or ranges property, but no unit name Another warning surfaces afterwards. Remove #address-cells and #size-cells from switch@1f node to fix this warning: Warning (avoid_unnecessary_addr_size): /ethernet@1e100000/mdio-bus/switch@1f: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* scripts/diffconfig.sh: ensure config/conf is builtEneas U de Queiroz2022-02-261-0/+1
| | | | | | | | | diffconfig.sh runs ./scripts/config/conf, but it does not get built with 'make {menu,x,n}config. Call 'make ./scripts/config/conf' to ensure it's been built before running it, aborting in case of failure. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>[removed Fixes: due revert]
* ath79: add Zyxel EMG2926-Q10AAlex Henrie2022-02-267-0/+20
| | | | | | | | | The Zyxel EMG2926-Q10A is 99% the Zyxel NBG6716, but the bootloader expects a different product name when flashing over TFTP. Also, the EMG2926-Q10A always has 128 MiB of NAND flash whereas the NBG6716 reportedly can have either 128 MiB or 256 MiB. Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
* x86: geode: fix package nameing kmod-crypto-ebc does not existFlorian Eckert2022-02-261-1/+1
| | | | | | | This commit fixes the package naming that was added by commit: e1e4cbde5ceb228e60fff1fc752cb90d9a7df2ab Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* bcm63xx: Fast 2704n: configure the WAN portDaniel González Cabanelas2022-02-261-2/+2
| | | | | | | | | | | | The Sagem/Plusnet F@ST2704N has a red label in ethernet port 4. Its purpose is to be used as Fibre/WAN with the stock firmware. Configure the Eth4 as WAN. Fixes: fbbb977772 (brcm63xx: Tune the network configuration for several routers) Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* mpc85xx: HiveAP-330: add tmp125 temperature sensorChristian Lamparter2022-02-253-1/+81
| | | | | | | | | | | the Aerohive HiveAP-330 and HiveAP-350 come equipped with an TI TMP125 temperature chip. This patch wires up the necessary support for this sensor and exposes it through hwmon / thermal sensor framework. Upstream support is coming, but it has to go through hwmon-next first. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: add disabled PSTORE+REED_SOLOMON symbols for 5.4Christian Lamparter2022-02-251-0/+15
| | | | | | | | | The last remaining 5.4 target currently chokes because the symbols haven't been disabled like for 5.10. Fixes: 97158fe10e60 ("kernel: package ramoops pstore-ram crash log storage") Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mac80211: add #if guards against 5.4 compile failuresChristian Lamparter2022-02-253-8/+14
| | | | | | | | | | | | | | | | | Both struct net_device_path_ctx and struct net_device_path are not available in 5.4. This causes an build error on the bcm63xx target. |mac80211/driver-ops.h: In function 'drv_net_fill_forward_path': |driver-ops.h:1502:57: error: passing argument 4 of |'local->ops->net_fill_forward_path' from incompatible pointer type | [-Werror=incompatible-pointer-types] | 1502 | ctx, path); | | ^~~ | | | | | struct net_device_path_ctx * Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* tools/quilt: update to 0.67Rosen Penev2022-02-253-5/+5
| | | | | | | | | | | | | | | | | | | | | | | - Call pager with original LANG environment variable - Consistently complain early if no series file is found - Fix handling of symbolic links by several commands - Tighten the patch format parsing - Reuse the shell (performance) - Document the series file format further - Document that quilt loads /etc/quilt.quiltrc - configure: Make stat configurable - series: Minor optimizations - setup: Don't obey the settings of any englobing .pc - setup: Default to fast mode - quilt.el: Fix documentation of quilt-pc-directory - quilt.el: Load /etc/quilt.quiltrc if ~/.quiltrc doesn't exist - quilt.el: Fix quilt-editable when QUILT_PATCHES_PREFIX is set Refresh patches. Signed-off-by: Rosen Penev <rosenp@gmail.com> [add changelog] Signed-off-by: Paul Spooren <mail@aparcar.org>
* CI: build changes in tools/ on ubuntu/macosPaul Spooren2022-02-251-0/+129
| | | | | | | | This commits adds GitHub CI to check that all tools compile on both Ubuntu and macOS. Since running in parrallel this should also detect badly set depdendencies within tools/Makefile. Signed-off-by: Paul Spooren <mail@aparcar.org>
* bcm4908: fix USB PHY supportRafał Miłecki2022-02-252-0/+294
| | | | | | This fixes problem with USB PHY not handling some USB 3.0 devices. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: generic: add missing 5.10 symbolsRui Salvaterra2022-02-251-3/+6
| | | | | | | | | | | | | | | Add the following kconfig symbols (disabled): CONFIG_DEFAULT_FQ CONFIG_DEFAULT_CODEL CONFIG_DEFAULT_SFQ Also resort the config with the kconfig.pl script. Fixes: f39872d966 ("kernel: generic: select the fq_codel qdisc by default") Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: kernel crash log ramoops storage for R7800 and XR500Hannu Nyman2022-02-241-0/+9
| | | | | | | | | | | | Define the kernel crash log storage ramoops/pstore feature for R7800 and its sister XR500. Reference to the ramoops admin guide in upstream Linux: https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html Tested with R7800. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* kernel: package ramoops pstore-ram crash log storageHannu Nyman2022-02-243-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Package the ability to log kernel crashes to 'ramoops' pstore files into RAM in /sys/fs/pstore Reference to the ramoops admin guide in upstream Linux: https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html The files in RAM survive a warm reboot, but not a cold reboot. Note: kmod-ramoops selects kmod-pstore and kmod-reed-solomon. The feature can be used by selecting the kmod-ramoops and adding a ramoops reserved-memory definition to the device DTS. Example from R7800: reserved-memory { rsvd@5fe00000 { reg = <0x5fe00000 0x200000>; reusable; }; ramoops@42100000 { compatible = "ramoops"; reg = <0x42100000 0x40000>; record-size = <0x4000>; console-size = <0x4000>; ftrace-size = <0x4000>; pmsg-size = <0x4000>; }; }; If no definition has been made in DTS, no crash log is stored for the device. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (added CONFIG_EFI_VARS_PSTORE disable)
* x86: grub2: search for the "kernel" filesystem on all disksJax Jiang2022-02-243-15/+5
| | | | | | | | | | | | | | | | | | | Previously, grub2 was hardcoded to always look on "hd0" for the kernel. This works well when the system only had a single disk. But if there was a second disk/stick present, it may have look on the wrong drive because of enumeration races. This patch utilizes grub2 search function to look for a filesystem with the label "kernel". This works thanks to existing setup in scripts/gen_image_generic.sh. Which sets the "kernel" label on both the fat and ext4 filesystem variants. Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com> Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA) (word wrapped, slightly rewritten commit message, removed MX100 WA) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* Revert "bcm27xx: bcm27xx: update defconfig"Christian Lamparter2022-02-244-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts all four commits dbb45421bab "bcm27xx: bcm2708: update defconfig" 332f69583ad "bcm27xx: bcm2709: update defconfig" a478202d74b "bcm27xx: bcm2710: update defconfig" 82da1dfd69a "bcm27xx: bcm2711: update defconfig" this also highlighted an unrelated kconfig failure that warrants investigation. But for now it is important for the bcm27xx target to come back again. |* |* Restart config... |* |* |* Allow override default queue discipline |* |Allow override default queue discipline (NET_SCH_DEFAULT) [Y/n/?] y | Default queuing discipline | 1. Fair Queue (DEFAULT_FQ) (NEW) | 2. Controlled Delay (DEFAULT_CODEL) (NEW) | > 3. Fair Queue Controlled Delay (DEFAULT_FQ_CODEL) | 4. Stochastic Fair Queue (DEFAULT_SFQ) (NEW) | 5. Priority FIFO Fast (DEFAULT_PFIFO_FAST) | choice[1-5?]: |Error in reading or end of file. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* at91: add support for sama7g5-ek boardClaudiu Beznea2022-02-245-6/+78
| | | | | | | | | | | | | | | | | | | | | | Add support for SAMA7G5-EK board. Hardware: - SoC: SAMA7G5 - RAM: Aliance Memory AS4C256M16D3LC (4 Gbit DDR3L) - SD/MMC: 1 standard 4bit SD Card interface - USB: 1 Micro-AB host/device, 1 Type-A host, 1 Type-C host - CAN: 2 interfaces - Ethernet: 10/100 port, 1Gbps port - Wi-Fi/BT: 1 optional interface - Audio: 1 SPDIF RX port, 1 SPDIF TX port, 4 digital microphones - Camera: 1 RPi CSI camera interface - Debug: 1 J-Link-OB + CDC, 1 JTAG - LEDs: 1 RGB - Buttons: 4 push buttons - Expansions: 1 RPi Expansion connector, 2 mikroBUS connectors - Power management: 1 power management IC, 1 power consumption measurement device Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* at91: add kernel support for sama7g5 socClaudiu Beznea2022-02-24152-7/+20714
| | | | | | | | | | | | | | | | Add kernel support for SAMA7G5 by back-porting mainline kernel patches. Among SAMA7G5 features could be remembered: - ARM Cortex-A7 - double data rate multi-port dynamic RAM controller supporting DDR2, DDR3, DDR3L, LPDDR2, LPDDR3 up to 533MHz - peripherals for audio, video processing - 1 gigabit + 1 megabit Ethernet controllers - 6 CAN controllers - trust zone support - DVFS for CPU - criptography IPs Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* uboot-at91: update to linux4sam-2021.10Claudiu Beznea2022-02-243-63/+38
| | | | | | Update uboot-at91 to linux4sam-2021.10 version. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* at91bootstrap: update to v3.10.4, v4.0.1Claudiu Beznea2022-02-243-42/+22
| | | | | | | | | | AT91Bootstrap version 4 is available only for SAM9X60, SAMA5D2, SAMA5D3, SAMA5D4, SAMA7G5. Thus use v4.0.1 for the above targets and v3.10.4 for the rest of them. With the switch to v4 AT91Bootstrap binaries are now on build/binaries. Take also this into account. Also, patches directory is not needed anymore with the version update. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* base-file: remove password aging feature form /etc/shadowRucke Teg2022-02-241-1/+1
| | | | | | | | | | | | | | In the default shadow file, as visible in the failsafe mode, the user root has value of `0` set in the 3rd field, the date of last password change. This setting means that the password needs to be changed the next time the user will log in the system. `dropbear` server is ignoring this setting but `openssh-server` tries to enforce it and fails in the failsafe mode because the rootfs is R/O. Disable the password aging feature for user root by setting the 3rd filed empty. Signed-off-by: Rucke Teg <rucketeg@protonmail.com>
* hostapd: SAE - Enable hunting-and-pecking and H2ENick Lowe2022-02-241-0/+2
| | | | | | | | | | | | | | | | | | | | | | | Enable both the hunting-and-pecking loop and hash-to-element mechanisms by default in OpenWRT with SAE. Commercial Wi-Fi solutions increasingly frequently now ship with both hunting-and-pecking and hash-to-element (H2E) enabled by default as this is more secure and more performant than offering hunting-and-pecking alone for H2E capable clients. The hunting and pecking loop mechanism is inherently fragile and prone to timing-based side channels in its design and is more computationally intensive to perform. Hash-to-element (H2E) is its long-term replacement to address these concerns. For clients that only support the hunting-and-pecking loop mechanism, this is still available to use by default. For clients that in addition support, or were to require, the hash-to-element (H2E) mechanism, this is then available for use. Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
* CI: allow dots in commit subject areaPaul Spooren2022-02-241-1/+1
| | | | | | | Due to a limited grep pattern, subjects containing dots like `image.mk` were falsely reported as problematic. Extend pattern to allow dots. Signed-off-by: Paul Spooren <mail@aparcar.org>
* tools: use https for bc mirrorsPaul Spooren2022-02-241-5/+5
| | | | | | All mirrors offer encrypted downloads, use it. Signed-off-by: Paul Spooren <mail@aparcar.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 17:04:58 +0000