aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx: Drop pci aliases to avoid domain changesMartin Kennedy2022-09-026-0/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As of upstream Linux commit 0fe1e96fef0a ("powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and alias"), the PCIe domain address is no longer numbered by the lowest 16 bits of the PCI register address after a fallthrough. Instead of the fallthrough, the enumeration process accepts the alias ID (as determined by `of_alias_scan()`). This causes e.g.: 9000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11) 9000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ... to become 0000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11) 0000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ... ... which then causes the sysfs path of the netdev to change, invalidating the `wifi_device.path`s enumerated in `/etc/config/wireless`. One other solution might be to migrate the uci configuration, as was done for mvebu in commit 0bd5aa89fcf2 ("mvebu: Migrate uci config to new PCIe path"). However, there are concerns that the sysfs path will change once again once some upstream patches[^2][^3] are merged and backported (and `CONFIG_PPC_PCI_BUS_NUM_DOMAIN_DEPENDENT` is enabled). Instead, remove the aliases and allow the fallthrough to continue for now. We will provide a migration in a later release. This was first reported as a Github issue[^1]. [^1]: https://github.com/openwrt/openwrt/issues/10530 [^2]: https://lore.kernel.org/linuxppc-dev/20220706104308.5390-1-pali@kernel.org/t/#u [^3]: https://lore.kernel.org/linuxppc-dev/20220706101043.4867-1-pali@kernel.org/ Fixes: #10530 Tested-by: Martin Kennedy <hurricos@gmail.com> [Tested on the Aerohive HiveAP 330 and Extreme Networks WS-AP3825i] Signed-off-by: Martin Kennedy <hurricos@gmail.com>
* at91bootstrap: use sdmmc0 as booting media for sama5d27_som1_ekClaudiu Beznea2022-09-022-9/+3
| | | | | | | | | | Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as default defconfig") changed default booting media for sama5d27_som1_ek board w/o any reason. Changed it back to sdmmc0 as it is for all the other Microchip supported distributions for this board (Buildroot, Yocto Project). The initial commit cannot be cleanly reverted. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* uboot-at91: use sdmmc0 as booting media for sama5d27_som1_ekClaudiu Beznea2022-09-023-16/+10
| | | | | | | | | | | Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs") changed the booting media to sdmmc1 as default booting w/o any reason. The Microchip releases for the rest of supported distributions (Buildroot, Yocto Project) uses sdmmc0 as default booting media for this board. Thus change it back to sdmmc0. With this remove references to sdmmc1 config. The initial commit cannot be cleanly reverted. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* kernel: fix DSA mac_select_pcs backportDaniel Golle2022-09-021-0/+88
| | | | | | | | Backport commit from Linux 5.18 fixing phylink with DSA drivers which do not provide mac_select_pcs yet. Fixes: aab466f422 ("kernel: backport generic phylink validate") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* unetd: update to the latest versionFelix Fietkau2022-09-012-3/+11
| | | | | | | | | | f5d02c32f811 pex: add support for sending endpoint notification from the wg port via raw socket c3b1127236a0 ubus: add support for querying active networks 8ad119715168 ubus: add support for adding auth_connect hosts at runtime 26dc52789d41 network: add support for configuring extra peers via a separate json file d7fb9e5b065b ubus: add reload command Signed-off-by: Felix Fietkau <nbd@nbd.name>
* unetd: fix handling of connect/tunnel listFelix Fietkau2022-09-011-3/+5
| | | | | | change the type to array, so that uci lists can be used Signed-off-by: Felix Fietkau <nbd@nbd.name>
* firewall4: update to latest Git HEADJo-Philipp Wich2022-09-011-3/+3
| | | | | | | | f5fcdcf cli: introduce test mode and refuse firewall restart on errors a540f6d fw4: fix cosmetic issue with per-ruleset and per-table include paths 695e821 doc: fix swapped include positions in nftables.d README Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* nettle: update to 3.8.1Nick Hainke2022-08-311-2/+2
| | | | | | | Release Notes: https://lists.gnu.org/archive/html/info-gnu/2022-07/msg00010.html Signed-off-by: Nick Hainke <vincent@systemli.org>
* readline: update to 8.1.2Nick Hainke2022-08-311-2/+2
| | | | | | Update to latest version. Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: fix typo for tegra crypto-sha1 moduleJosef Schlehofer2022-08-311-1/+1
| | | | | | | Fixes: e889489bedfd2830411bd0cf6564b8272aa9c254 ("kernel: build arm/neon-optimized sha1/512 modules") Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* realtek: Fix missing clock module CONFIG settingMarkus Stockhausen2022-08-311-0/+1
| | | | | | | Since introduction of clock driver we have a new kernel config setting. Provide an initial value for the 930x targets. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
* realtek: fix PLL register inconsistenciesMarkus Stockhausen2022-08-311-0/+3
| | | | | | | Some devices have wrong/empty values in the PLL registers. Work around that by reporting the default values. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
* kernel: bump 5.10 to 5.10.139John Audia2022-08-313-29/+23
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* arm-trusted-firmware-mediatek: update to sources of 2022-08-31Daniel Golle2022-08-313-75/+3
| | | | | | | Drop downstream patches which have been replaced with equivalent upstream changes. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: replace patches with updated versionsDaniel Golle2022-08-3136-164/+791
| | | | | | | | | | | | | | | | Weijie Gao has submitted an updated version of the patchset adding support for MT7986 and MT7981 to U-Boot. Use that v2 patchset. Changes of v2: - Add cpu driver for print_cpuinfo() - Fix NULL pointer dereference in mtk_image (was already fixed in OpenWrt) - Fix coding style - Minor changes https://patchwork.ozlabs.org/project/uboot/list/?series=316148 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Bananapi BPi-R3Daniel Golle2022-08-309-2/+920
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Bananapi BPi-R3 is a development router board built around the MediaTek Filogic 830 (MT7986A) SoC. The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC. Only either SPI-NAND or SPI-NOR can be used at the same time, also only either microSD or eMMC can be used. The various storage options can be selected using small SMD switches on the board. Specs: * MediaTek MT7986A (Filogic 830) 4x ARM Cortex A53 * 4T4R 2.4G 802.11bgnax (MT7975N) * 4T4R 5G 802.11anac/ax (MT7975P) * 2 GB DDR4 RAM * 8 GB eMMC * 128 MB SPI-NAND flash * 32 MB SPI-NOR flash * on-board MT7531 GbE switch * 2x SFP+ (1 GbE / 2.5 GbE) * 5x GbE network port * miniPCIe slot (only USB 2.0 connected) * uSIM slot (connected to miniPCIe interface) * M.2 KEY-E PCIe interface (PCIe x2) * microSD card interface * 26 PIN GPIO Hardware details: https://wiki.banana-pi.org/Banana_Pi_BPI-R3 Working: * all 4 boot methods incl. installation via U-Boot, sysupgrade, ... * copper LAN and WAN ports * SFP1 (connected to gmac1, eth1 in Linux) * WiFi * LEDs * Buttons * PSTORE/ramoops based dual-boot Not Working (missing driver features): * SFP2 (connected to MT7531 switch) Untested: * M.2/NGFF slot (PCIe x2) * mPCIe slot (USB 2.0 + SIM) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add support for Bananapi BPi-R3Daniel Golle2022-08-301-0/+45
| | | | | | | Create new mediatek_filogic file and add entries for environment on MMC, UBI and NOR for the Bananapi BPi-R3. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add support for Bananapi BPi-R3Daniel Golle2022-08-302-3/+1428
| | | | | | | | | | | | | | | The Bananapi BPi-R3 board can boot from eMMC, SD card, SPI-NAND and SPI-NOR, depending on the position of switches controlling the BOOTSEL bootstrap pins as we as hard-wired chip-select lines. The position of the chip-select switch SW6 decides whether either SD card or eMMC can be accessed, SW5 selects either SPI-NAND or SPI-NOR. Generate U-Boot for all 4 boot options. The SD card version allows installation to SPI-NAND and SPI-NOR (eMMC cannot be accessed simultanously with the SD card), the SPI-NAND version allows installation to eMMC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: add pending mtk_sgmii and phy improvements from @lynxisDaniel Golle2022-08-3010-0/+467
| | | | | | | | | | | | | Add pending patches from Alexander 'lynxis' Couzens which are required for RealTek NBase-T PHYs or SFP+ cages to work when connected to the SGMII interface provided by recent MediaTek SoCs [1]. The patches for MT753x fix link speed limitation on CPU ports observed by many users which is due to reset being carried out wrongly [2]. [1]: https://patchwork.kernel.org/project/netdevbpf/list/?series=669488&state=* [2]: https://patchwork.kernel.org/project/netdevbpf/list/?series=669486&state=* Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: backport generic phylink validateDaniel Golle2022-08-3056-28/+4446
| | | | | | | Backport generic phylink validate series and make use of it for mtk_eth_soc Ethernet driver as well as mt7530 DSA driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: disable ft-over-ds by defaultFelix Fietkau2022-08-301-1/+1
| | | | | | | | Testing has shown it to be very unreliable in variety of configurations. It is not mandatory, so let's disable it by default until we have a better solution. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* update: update to latest Git HEADJo-Philipp Wich2022-08-301-3/+3
| | | | | | | 344fa9e lib: extend render() to support function values 89452b2 lib: improve getenv() and split() implementations Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* unetd: update to the latest version, makes VXLAN/eBPF optionalFelix Fietkau2022-08-291-8/+22
| | | | | | | | | | b75791a6db25 scripts/update-cmd.pl: reorder add/remove calls to better deal with dynamic changes c29e1ad045d0 scripts/update-cmd.pl: set device up before adding routes/addresses 5ad35ce4beea scripts/update-cmd.pl: run update two times 5d79b88f00c1 add support for overriding peer-exchange-port for individual hosts 0041fcacb624 add support for disabling VXLAN/eBPF support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: define Yuncore AX820 switch LEDsThibaut VARÈNE2022-08-292-0/+20
| | | | | | | | | This patch defines the two switch LED to bring them under user control. Fixes: a0e1d3ab7b4f ("ramips: improve YunCore AX820 LEDs") Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> [rmilecki: leave "label"s in place] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* realtek: tl-sg2008p: fix labeling of lan portsAlexandru Gagniuc2022-08-291-8/+8
| | | | | | | | The SG2008P has its ethernet ports in the rear, and LEDs in the front. The ports should be labeled lan8->lan1, not lan1->lan8. To resolve this, fix the phy mapping in the "ports" node. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
* realtek: tl-sg2008p: use correct i2c address for TPS23861Alexandru Gagniuc2022-08-291-2/+2
| | | | | | | | Address 0x30 is a "broadcast" address for the TPS23861. It should not be used by drivers, as all TPS23861 devices on the bus are supposed to respond. Change this to the correct address, 0x28. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
* realtek: ignore disabled switch portsSander Vanheule2022-08-291-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | When marking a switch port as disabled in the device tree, by using 'status = "disabled";', the switch driver fails on boot, causing a restart: CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 802c3064, ra == 8022b4b4 [ ... ] Call Trace: [<802c3064>] strlen+0x0/0x2c [<8022b4b4>] start_creating.part.0+0x78/0x194 [<8022bd3c>] debugfs_create_dir+0x44/0x1c0 [<80396dfc>] rtl838x_dbgfs_port_init+0x54/0x258 [<80397508>] rtl838x_dbgfs_init+0xe0/0x56c This is caused by the DSA subsystem (mostly) ignoring the port, while rtl83xx_mdio_probe() still extracts some details on this disabled port from the device tree, resulting in the usage of a NULL pointer where a port name is expected. By not probing ignoring disabled ports, no attempt is made to create a debugfs directory later. The device then boots as expected without the disabled port. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: add support for Extreme Networks WS-AP3805iAlbin Hellström2022-08-296-0/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: Qualcomm Atheros QCA9557-AT4A - RAM: 2x 128MB Nanya NT5TU64M16HG - FLASH: 64MB - SPANSION FL512SAIFG1 - LAN: Atheros AR8035-A (RGMII GbE with PoE+ IN) - WLAN2: Qualcomm Atheros QCA9557 2x2 2T2R - WLAN5: Qualcomm Atheros QCA9882-BR4A 2x2 2T2R - SERIAL: UART pins at J10 (115200 8n1) Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) - LEDs: Power (Green/Amber) WiFi 5 (Green) WiFi 2 (Green) - BTN: Reset Installation: 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to 1D01A8C0.img Configure the TFTP server to listen at 192.168.1.66/24. 2. Connect the TFTP server to the access point. 3. Connect to the serial console of the access point. Attach power and interrupt the boot procedure when prompted. Credentials are admin / new2day 4. Configure U-Boot for booting OpenWrt from ram and flash: $ setenv boot_openwrt 'setenv bootargs; bootm 0xa1280000' $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66; tftpboot 0x89000000 1D01A8C0.img; bootm' $ setenv bootcmd 'run boot_openwrt' $ saveenv 5. Load OpenWrt into memory: $ run ramboot_openwrt 6. Transfer the OpenWrt sysupgrade image to the device. Write the image to flash using sysupgrade: $ sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: Albin Hellström <albin.hellstrom@gmail.com> [rename vendor - minor style fixes - update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* unetd: update to the latest versionFelix Fietkau2022-08-281-3/+3
| | | | | | | | 5cbd55f60346 unet-cli: fix formatting of help text 59b97448b636 build.sh: force use of -fPIC on static libraries to fix build error 74a14c00abb0 pex-msg: fix siphash key initializer Signed-off-by: Felix Fietkau <nbd@nbd.name>
* wolfssl: Rebuild when libwolfssl-benchmark gets changesHauke Mehrtens2022-08-281-0/+1
| | | | | | | | | | This forces a rebuild of the wolfssl package when the libwolfssl-benchmark OpenWrt package gets activated or deactivated. Without this change the wolfssl build will fail when it compiled without libwolfssl-benchmark before and it gets activated for the next build. Fixes: 18fd12edb810 ("wolfssl: add benchmark utility") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: enable inside secure driver for MediaTek platformsDaniel Golle2022-08-285-6/+8
| | | | | | | | Older MT7623 ARMv7 SoC as well as new Filogic platforms come with inside-secure,safexcel-eip97 units. Enable them in DTS and select the driver kernel module by default on those platforms. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mt76: add mt7986 wmac supportFelix Fietkau2022-08-281-0/+24
| | | | | | Add firmware package for MT7986 and enable WMAC support in the driver Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add filogic subtargetFelix Fietkau2022-08-286-1/+552
| | | | | | | | Initially this covers MT7986 only, but it will later be expanded to cover other Filogic branded platforms by MediaTek Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add mt7986 soc support to the targetSam Shih2022-08-2825-0/+4286
| | | | | | | | | It will be supported by the new filogic subtarget Signed-off-by: Sam Shih <sam.shih@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: no compression means IH_COMP_NONEDaniel Golle2022-08-283-1/+120
| | | | | | | | | | Treat missing compression node in FIT image as IH_COMP_NONE. This is implicentely already happening in most places, but for now was still triggering an annoying warning about initramfs compression being obsolete despite compression note being absent. Fix this. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: mt7986: add generic reset button supportDaniel Golle2022-08-281-0/+40
| | | | | | | Allow resetting environment to default values when defined button exists in device tree. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: mt7986: support PSTORE/ramoopsDaniel Golle2022-08-281-0/+38
| | | | | | Assign reserved memory for PSTORE/ramoops for the MT7986 SoC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: additions from MTK SDKDaniel Golle2022-08-2845-276/+10562
| | | | | | | | | | | | | | | * updated SNAND/SNFI driver brings support for MT7981 * add support for MediaTek NAND Memory bad Block Management (NMBM) (not used for any boards atm, but could be useful in future) * wire up NMBM support for MT7622, MT7629, MT7981 and MT7986 * replace some local patches with updated version from SDK * bring some legacy precompiler symbols which haven't been converted into Kconfig symbols in U-Boot 2022.07, remove when bumbping to U-Boot 2022.10: 100-28-include-configs-mt7986-h-from-SDK.patch Source: https://github.com/mtk-openwrt/u-boot Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add support for MT798x platformsDaniel Golle2022-08-2836-6/+12173
| | | | | | Import pending patches to support the upcoming Filogic platforms. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add support for compressed BL3/FIP imageDaniel Golle2022-08-282-13/+7
| | | | | | | MediaTek's ARM Trusted Firmware v2.7+ allows the images inside a FIP structure to be compressed. Make use of that for boards with NOR flash. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: fix factory reset on UBIDaniel Golle2022-08-282-2/+2
| | | | | | | Truncating a UBI volume using `ubi write 0x0 volname 0x0` results in segfault on newer U-Boot. Write 1MB of 0s instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: update to v2.7+ from MediaTekDaniel Golle2022-08-284-50/+192
| | | | | | | | | | | | | | | | | | | | The updated sources bring support for the MT798x Filogic SoC family. Add builds for MT7986 with most supported storage types, each for DDR3 and DDR4 configurations. A better solution for skipping bad blocks on SPI-NAND connected via the SNFI interface has been implemented upstream, so drop local patch. Add pending patches [1] and [2] to fix boot on existing MT7622 boards. Tested on BananaPi BPi-R64 (SDMMC, eMMC, SPI-NAND), Linksys E8450 and Ubiquiti UniFi 6 LR as well as upcoming Bananapi BPi-R3 board for which support will be added in future patches. [1]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#3 [2]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#4 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* trusted-firmware-a.mk: pass DTC path similar to u-boot.mkDaniel Golle2022-08-285-0/+7
| | | | | | | | | Instead of relying on dtc being provided by the build host use the dtc from $(LINUX_DIR) similar to how it's done also in u-boot.mk. For this to work kernel.mk now needs to be included before trusted-firmware-a.mk, add this include to all affected packages. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* tools: mkimage: Add support for MediaTek MT798xDaniel Golle2022-08-283-0/+1612
| | | | | | | Import pending patches for mtk_image to support BootROM headers of newer MediaTek SoCs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* popt: update to 1.18Nick Hainke2022-08-281-8/+5
| | | | | | | | | | | | | | | | | | | | Changes from popt 1.16: - fix an ugly and ancient security issue with popt failing to drop privileges on alias exec from a SUID/SGID program - perform rudimentary sanity checks when reading in popt config files - collect accumulated misc fixes (memleaks etc) from distros - convert translations to utf-8 encoding - convert old postscript documentation to pdf - dust off ten years worth of autotools sediment - reorganize and clean up the source tree for clarity - remove the obnoxious splint annotations from the sources Switch to new mirror: http://ftp.rpm.org/popt/releases/ Switch URL to: https://github.com/rpm-software-management/popt Signed-off-by: Nick Hainke <vincent@systemli.org>
* nftables: update to 1.0.5Nick Hainke2022-08-282-52/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove upstreamed patch: - 0001-meta-don-t-use-non-POSIX-formats-in-strptime.patch Changes: 13248670 build: Bump version to 1.0.5 3432eebd tests/py: disable arp family for queue statement 180ce4d7 meta: don't use non-POSIX formats in strptime() c1c223f1 src: allow anon set concatenation with ether and vlan 87c3041b evaluate: search stacked header list for matching payload dep b1e3ed03 netlink_delinearize: also postprocess OP_AND in set element context f680055c tests: add a test case for ether and vlan listing dbd5f348 debug: dump the l2 protocol stack 0d9daa04 proto: track full stack of seen l2 protocols, not just cumulative offset 89688c94 netlink_delinearize: postprocess binary ands in concatenations 0542a431 netlink_delinearize: allow postprocessing on concatenated elements 8efab552 parser_json: fix device parsing in netdev family 76fae8f5 src: proto: support DF, LE PHB, VA for DSCP 446e76db doc: Document limitations of ipsec expression with xfrm_interface a2ddb38f cache: report an error message if cache initialization fails 649b8ce3 cache: validate handle string length 64c74ba5 cache: prepare nft_cache_evaluate() to return error 46980cdd rule: crash when uncollapsing command with unexisting table or set 8a6cdfaf cache: release pending rules when chain binding lookup fails e17337df evaluate: report missing interval flag when using prefix/range in concatenation 45c097c6 scanner: allow prefix in ip6 scope 6c23bfa5 segtree: fix map listing with interface wildcard 8623772a scanner: don't pop active flex scanner scope 994bf500 parser: add missing synproxy scope closure ed2426bc tests/py: Add a test for failing ipsec after counter 27107b49 evaluate: fix segfault when adding elements to invalid set 0f82b07f mnl: store netlink error location for set elements 15b3be2e src: remove NFT_NLATTR_LOC_MAX limit for netlink location error reporting f56e901a parser_bison: fix error location for set elements 6d1ee926 intervals: check for EXPR_F_REMOVE in case of element mismatch 5357cb7b intervals: fix crash when trying to remove element in empty set d54510f8 netlink_delinearize: memleak when parsing concatenation data 12a223ce libnftables: release top level scope b91bbf88 optimize: limit statement is not supported yet 45a61a75 optimize: assume verdict is same when rules have no verdict fa409176 optimize: only merge OP_IMPLICIT and OP_EQ relational 29e62111 tests: shell: run -c -o on ruleset 887405df optimize: add unsupported statement 8f61a69e optimize: add hash expression support ca8fd77a optimize: add numgen expression support 721efd64 optimize: add binop expression support f7e901a2 optimize: add fib expression support 54b1e49f optimize: add xfrm expression support 0beaea37 optimize: add osf expression support d07fe8e8 optimize: fix verdict map merging 38d48fe5 optimize: fix reject statement f9939f89 optimize: remove comment after merging 8f10f33a optimize: do not print stateful information 3ac932e9 optimize: do not merge rules with set reference in rhs 64ebb03a optimize: do not compare relational expression rhs when collecting statements 59e3a592 intervals: Do not sort cached set elements over and over again d434de8b intervals: do not empty cache for maps 87ba510f intervals: do not report exact overlaps for new elements 498a5f0c rule: collapse set element commands 8fafe4e6 tests: shell: runtime set element automerge 638af0ce Revert "scanner: flags: move to own scope" Signed-off-by: Nick Hainke <vincent@systemli.org>
* libnftnl: update to 1.2.3Nick Hainke2022-08-281-2/+2
| | | | | | | | Changes: 817c8b6 build: libnftnl 1.2.3 release 84d12cf build: fix clang+glibc snprintf substitution error Signed-off-by: Nick Hainke <vincent@systemli.org>
* iproute2: replace musl-compilation-fix with upstream fixNick Hainke2022-08-282-27/+23
| | | | | | | | | | | | | Instead of defining the MIN version it is enough to include "#include <sys/param.h>". Delete patch: - 105-ipstats-Define-MIN-function-to-fix-undefined-referen.patch Add patch: - 010-ipstats-Add-param.h-for-musl.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* wireguard-tools: update to v1.0.20210914Nick Hainke2022-08-281-2/+2
| | | | | | Update to latest version. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ethtool: update to 5.19Nick Hainke2022-08-281-2/+2
| | | | | | | Release Notes: https://lore.kernel.org/netdev/20220821234539.f7nslwyd53bsftsy@lion.mk-sys.cz/T/ Signed-off-by: Nick Hainke <vincent@systemli.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-19 01:37:20 +0000