aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-164-0/+199
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-163-1/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* readline: add host PICRosen Penev2022-04-161-0/+1
| | | | | | | Python seems to fail to link to libreadline properly because of this. Not a fatal error but an error nontheless. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* pcre: pass -fPIC under host as wellRosen Penev2022-04-161-4/+4
| | | | | | static libraries need them as they are not PIC by default. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* lantiq: fritz736x: Move GPIO resets to the inidvidual board.dts filesMartin Blumenstingl2022-04-164-32/+77
| | | | | | | | | | FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0) and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362 SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the GPIO reset definitions to each individual board .dts and while at it, fix the GPIOs for the FRITZ!Box 7362 SL. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* comgt: support ZTE MF286R modemCezary Jackiewicz2022-04-162-1/+23
| | | | | | | | | | | | The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to establish connection with custom commands specific to ZTE modems. Two variants of modems were discovered, some identifying themselves as "ZTE", and others as plain "Marvell", the chipset manufacturer. The modem itself runs a fork of OpenWrt inside, which root shell can be accessed via ADB interface. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* comgt: ncm: try to detect interface for ttyACM portsLech Perczak2022-04-161-0/+4
| | | | | | | | | | | Some modems expose ttyACM as their control ports, which have the "device" symlink pointing one level down in sysfs tree. Try to find network interfaces for them as well, this is commonly used for modems exposing ACM + RNDIS or ACM + ECM interface combinations. Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* comgt: ncm: select first available network interface for deviceLech Perczak2022-04-161-3/+4
| | | | | | | | | | | | | Some modems expose multiple network interfaces on the same USB device, causing the connection setup script to fail, because glob matching in the detection phase causes 'ls' to output more than one interface name plus their base directories in sysfs. Avoid that by listing the directories explicitly and then selecting first available interface. This is the case for some variants of ZTE MF286R built-in modem, which exposes both RNDIS and CDC-ECM network interfaces, causing the connection setup to fail. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* comgt: ncm: allow specification of interface nameLech Perczak2022-04-161-14/+18
| | | | | | | | | | | | Add ifname property to UCI, which can be used to override the autodetected interface name in case the detection fails due to having none or more than one interface exposed by the modem, which is not explicitly linked to TTY port. This is needed on certain variants of ZTE MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces on the modem, on which the automatic detection may select the wrong network interface. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* kernel: backport ZTE RNDIS bogus MAC address fixLech Perczak2022-04-166-0/+478
| | | | | | | | | | | This is required to support built-in modem of ZTE MF286R, in addition to other external modems, such as MF831, MF910, MF920, which refuse to reconfigure their remote MAC address, even if "locally administered" bit is set, leading to dropped traffic towards the host. Add a workaround for that issue already present in cdc_ether to rndis_host driver as well. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq806x: fix wrong CPU OPP for ipq8062Ansuel Smith2022-04-161-16/+16
| | | | | | | | | Fix wrong CPU OPP for ipq8062. Revision of the SoC added an extra 25mV for every pvs. Also fix the voltage min/max value that were wrong. Reviewed-by: Robert Marko robimarko@gmail.com Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: fix USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-161-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The existing device tree has incorrect definitions for usb3_0 and usb3_1 and the blocks they depend upon: their addresses and interrupts are swapped. However, their clocks and resets are not. The result is that the USB blocks are non-functional if only one of them is enabled. This fix backports the definitions from mainline Linux 5.15 to OpenWrt's 5.10 dtsi additions. See the relevant mainline code here: https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148 This fix does not break existing ports. But some ports may have enabled both USB blocks even thought their board only implements one, because enabling a single USB block would not have worked before this fix. This means that revisiting all ports of ipq806x devices that implement a single USB port is advised. This work must be done by maintainers that can determine which USB block corresponds to the implemented port on their hardware. Note that this fix swaps the names of the hardware ports. This is unfortunate, but will happen anyway when switching to kernel 5.15. Thus, it is best to do this ASAP, before users get to depend on port names. It is strongly recommended that this fix is backported to 22.03 before its release. This will minimize the number of users affected by the port name swap. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* ipq806x: remove non-working fixes for USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-162-4/+0
| | | | | | These workarrounds are incomplete and non-functional, and thus not needed. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* ath79: port HiWiFi HC6361 from ar71xxYousong Zhou2022-04-164-0/+173
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The device was added for ar71xx target and dropped during the ath79 transition, mainly because of the ascii mac address stored in bdinfo partition Device page, http://wiki.openwrt.org/toh/hiwifi/hc6361 The vendor u-boot image accepts sysupgrade.bin image with specific requirements, including having squashfs signature "hsqs" at file offset 0x140000. This is not possible now that OpenWrt kernel image is at least 2MB with the signature at offset 0x240000. Installation of current build of OpenWrt now requires a bootstrap step of installing an earlier version first. - If the vendor u-boot accepts sysupgrade image, hc6361 image of LEDE release should work - If the vendor u-boot accepts only verified flashsmt image, install the one in the above device page. The image is based on Barrier Breaker SHA256SUM of the flashsmt image 81b193b95ea5f8e5c30cd62fa9facf275f39233be4fdeed7038f3deed2736156 After the bootstrap step, current build of OpenWrt can be installed there fine. Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ath79: add nvmem cell mac-address-ascii supportYousong Zhou2022-04-162-0/+206
| | | | | | | This is needed for devices with mac address stored in ascii format, e.g. HiWiFi HC6361 to be ported in the following patch. Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* image: strip metadata from images when used in other artifactsDaniel Golle2022-04-151-3/+11
| | | | | | | | | Image metadata and signature is of no use for images which are included inside other artifacts (like an SD-card image). Strip them off before using images in artifacts or stashing them for the ImageBuilder as the contained signature breaks reproducibility. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: cleanup mikrotik routerboot partitionsThibaut VARÈNE2022-04-157-12/+6
| | | | | | | | | For some reason useless labels and aliases have been propagated through copy-paste. Before the issue spreads any further, this patch cleans up all relevant DTS files to the canonical form, bringing ath79 in line with other mikrotik platforms (ramips and ipq40xx). Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: add support for Yuncore A930Thibaut VARÈNE2022-04-153-0/+129
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* mac80211 adjust QCA9561 PA biasThibaut VARÈNE2022-04-151-0/+18
| | | | | | | | | | | | | | | ath9k is setting the TX PA DC bias level different on QCA9561 and QCA9565 although they have the same radio IP-core, which results in a very low output power and very low throughput as devices are further away from the AP (compared to other 2.4GHz APs.) In real life testing, without this patch the 2.4GHz throughput on Yuncore XD3200 is around 10Mbps sitting close to the AP, and close to theoretical maximum with the patch applied. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> [edit commit message] Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: add support for Yuncore XD3200Thibaut VARÈNE2022-04-156-2/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* build: target: improve UX of CONFIG_TARGET handlingPetr Štetiar2022-04-151-7/+15
| | | | | | | | | | | | | | | | | | | | Make it clear, that for `make kernel_{menu,old}config` it's possible to use only following values for CONFIG_TARGET variable: * env * target * subtarget * subtarget_target This should prevent misuse like `make kernel_menuconfig CONFIG_TARGET=bcm2710` etc. Keep support for obsolete `platform` and `subtarget_platform` targets with deprecation notice so this compat stuff could be removed in the future. Signed-off-by: Petr Štetiar <ynezz@true.cz> Acked-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: usb-net-asix: fix 5.15 dependencyPetr Štetiar2022-04-151-1/+1
| | | | | | | | | | | | Upstream in commit 34a1dee6bc44 ("net: usb: asix: ax88772: add generic selftest support") in version 5.14 added dependency on generic selftest functionality and armvirt/64 when compiled with ALL_KMODS=y reports following: Package kmod-usb-net-asix is missing dependencies for the following libraries: mdio_devres.ko selftests.ko Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: netdevices: add generic selftests modulePetr Štetiar2022-04-151-0/+16
| | | | | | | | | | Upstream in commit 3e1e58d64c3d ("net: add generic selftest support") in version 5.13 added generic selftests module and usb-net-asix already depends on it, in version 5.18 via commit 1710b52d7c13 ("net: usb: smsc95xx: add generic selftest support") it will be used by usb-net-smsc95xx as well. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: usb-net-smsc95xx: fix 5.15 dependencyPetr Štetiar2022-04-151-1/+1
| | | | | | | | | armvirt/64 when compiled with ALL_KMODS=y reports following: Package kmod-usb-net-smsc95xx is missing dependencies for the following libraries: libphy.ko Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: mdio-devres: fix of-mdio dependencyPetr Štetiar2022-04-151-1/+1
| | | | | | | | | armvirt/64 when compiled with ALL_KMODS=y reports following: Package kmod-mdio-devres is missing dependencies for the following libraries: of_mdio.ko Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: of-mdio: fix 5.15 fwnode_mdio dependencyPetr Štetiar2022-04-151-1/+2
| | | | | | | | | | | | Upstream in commit bc1bee3b87ee ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()") in version 5.14 introduced new dependency: Package kmod-of-mdio is missing dependencies for the following libraries: fwnode_mdio.ko Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mtools: update to version 4.0.39Daniel Golle2022-04-151-2/+2
| | | | | | | | | Improvements since the 4.0.38 release are: - Rename strtoi to strosi (string to signed int). The strtoi function on BSD does something else (returns an intmax, not an int) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* scripts/gen_image_generic.sh: fix order of files in EFI bootfsDaniel Golle2022-04-151-2/+19
| | | | | | | | | | | | mtools recursive copy (mcopy -s ...) is using READDIR(3) to iterate over the directory entries, hence they end up in the FAT filesystem in traversal order which breaks reproducibility (rather than being added to the FAT filesystem in a reproducible order). Implement recursive copy in gen_image_generic.sh in Shell code instead, as in that way we can force files to be copied in reproducible order. Fixes: aece8f5ae8 ("scripts/gen_image_generic.sh: generate reproducible EFI filesystem") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* gemini: Bump kernel to v5.15Linus Walleij2022-04-141-1/+1
| | | | | | | It's working well on all tested targets, so let's move Gemini forward to v5.15. imx is already bumped so why not. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gemini: Create patches and config for kernel v5.15Linus Walleij2022-04-143-0/+588
| | | | | | | | | This creates a v5.15 baseline for the Gemini platform. The main new attraction is the new crypto driver from Corentin Labbe that we activate in the new config. Config was refreshed. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* generic: backport 5.16 RTL8366RB improvementsLinus Walleij2022-04-148-0/+920
| | | | | | | The prerequisite DSA changes for the nice RTL8366RB improvements are already backported so bring back these changes as well. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* urandom-seed: go back to seeding with shell script temporarilyJason A. Donenfeld2022-04-145-442/+35
| | | | | | | | | | | | | | | | This reverts commit 2edc017a6e0cb92b72b768aaa46c6d336ad84eff. We shouldn't be using a shell script here, but the SeedRNG integration into OpenWRT requires a bit more thought. Etienne raised some important points immediately after this was merged and planned to send some follow up commits, but became busy with other things. The points he raised are important enough that we should actually back this out until it's ready to go, and then merge it as a cohesive unit. So let's revert this for now, and come back to it later on. Cc: Etienne Champetier <champetier.etienne@gmail.com> Cc: Petr Štetiar <ynezz@true.cz> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* mediatek: 5.15: re-enable arch timer on MT7623 as wellDaniel Golle2022-04-141-0/+1
| | | | | | Re-enable arch timer also on MT7623, yet another time. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: 5.15: enable arm arch timer for mt7629Chuanhong Guo2022-04-142-0/+12
| | | | | | otherwise the system delay is completely broken. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: 5.15: add support for ESMT F50x1G41LBChuanhong Guo2022-04-141-0/+143
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* netifd: relax check in dhcp proto handlerDaniel Golle2022-04-131-1/+1
| | | | | | | | | Checking whether /sbin/udhcpc is a symbolic link breaks using the DHCP proto handler inside procd-ujail where bind-mounts are used for the resolved link. Check whether /sbin/udhcpc is executable instead to allow using the proto handler for DHCP-provisioned containers. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2022-04-131-3/+3
| | | | | | | | 6343c3a procd: completely remove tmp-on-zram support 5c5e63f uxc: fix potential NULL-pointer dereference eb03f03 jail: include necessary files for per-netns netifd instance Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* malta: add config-5.15Daniel Golle2022-04-131-0/+263
| | | | | | | | Adding the kernel configuration has accidentally been omitted when enabling testing kernel 5.15. Add it now. Fixes: 09f6200198 ("malta: enable testing kernel 5.15") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* base-files: more robust sysupgrade on NANDDaniel Golle2022-04-131-4/+10
| | | | | | | | | Make sure sysupgrade on NAND also works in case of UBI volumes having index >9. While at it, also make sure UBI device is detected and abort in case it isn't. Use Shell built-in shorthand ':' instead of 'true'. Fixes #9708 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* firewall3: bump to latest git HEADRui Salvaterra2022-04-131-3/+3
| | | | | | | 4cd7d4f Revert "firewall3: support table load on access on Linux 5.15+" 50979cc firewall3: remove unnecessary fw3_has_table Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ath79: nand: add 5.15 support for nand subtargetKoen Vandeputte2022-04-131-0/+2
| | | | | | Tested on GL.iNet E750 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: add missing symbols for 5.15Koen Vandeputte2022-04-131-0/+7
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* netfilter: move nf-log modules into separate packagesJo-Philipp Wich2022-04-122-7/+33
| | | | | | | | Both legacy iptables and nftables require nf-log modules for rule logging, so move them into a separate package both firewall implementations can depend on. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mac80211: backport minstrel_ht fix for legacy ratesFelix Fietkau2022-04-121-0/+61
| | | | | | Fixes OFDM rates on 5 GHz Signed-off-by: Felix Fietkau <nbd@nbd.name>
* toolchain: musl: Update to version 1.2.3Hauke Mehrtens2022-04-112-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: new features: - qsort_r function (POSIX-future) - pthread_getname_np extension function - hard float on SPE FPU for powerpc-sf - SEEK_DATA and SEEK_HOLE exposed in unistd.h (Linux extensions) compatibility: - free now preserves errno (POSIX-future requirement) - setjmp is declared explicitly with returns_twice for non-GCC compilers - macro version of isascii is no longer defined for C++ - dynamic linker now tolerates zero-length LOAD segments - epoll_[p]wait is now a cancellation point - pwd/grp functions no longer fail on systems without AF_UNIX support - POSIX TZ parsing is stricter to allow more names to fallback to files - NULL is now defined as nullptr when used in C++11 or later - gettext now accepts null pointer as argument bugs fixed: - old regression in wcwidth of Hangul combining (vowel/final) letters - duplocale used wrong malloc when malloc was replaced (1.2.2 regression) - fmaf rounded wrong on archs without FE_TOWARDZERO (all softfloat archs) - popen didn't honor requirement not to leak other popen pipe fds to child - aligned_alloc and variants crashed on allocation failure - dl_iterate_phdr reported incorrect module TLS pointers - mishandling of some inputs in acoshf and expm1f and functions using them - potentially wrong-sign zero in cproj functions at infinity - multiple bugs in legacy function cuserid - minor posix_spawn file actions API conformance issues - pthread_setname_np fd leak - out-of-bound read in zoneinfo handling with distant-past times - out-of-tree builds lacked generated debug cfi for x86 asm arch-specific bugs fixed: - powerpc (32-bit) struct shmid_ds layout was wrong for some fields - time64 struct layout was wrong in sound ioctl fallback (32-bit archs) In addition it contains the following improvements: * protect stack canary from leak via read-as-string by zeroing second byte * fix excessively slow TLS performance on some mips models Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Rui Salvaterra <rsalvaterra@gmail.com> Tested-by: Rui Salvaterra <rsalvaterra@gmail.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* nftables: add CONFLICT between versionsEneas U de Queiroz2022-04-111-1/+2
| | | | | | Have nftables-json conflict with nftables-nojson. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* wolfssl: bump to 5.2.0Eneas U de Queiroz2022-04-114-9/+7
| | | | | | | | | | | | | | | | Fixes two high-severity vulnerabilities: - CVE-2022-25640: A TLS v1.3 server who requires mutual authentication can be bypassed. If a malicious client does not send the certificate_verify message a client can connect without presenting a certificate even if the server requires one. - CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS v1.3 server can have its certificate heck bypassed. If the sig_algo in the certificate_verify message is different than the certificate message checking may be bypassed. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mediatek/mt7622: enable accelerated crypto driversEneas U de Queiroz2022-04-112-0/+20
| | | | | | | | | Use ARMv8 Crypto Extensions for AES, ghash and sha256. This results in a 16 times speed gain in speed for aes-128-ctr, 17x in aes-128-gcm, and 9 times in sha256. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* scripts/gen_image_generic.sh: generate reproducible EFI filesystemDaniel Golle2022-04-111-2/+3
| | | | | | | | | Generate FAT filesystem for EFI boot in a reproducible way: * use '--invariant' option of mkfs.fat * set timestamps of all files to SOURCE_DATE_EPOCH * make sure files are ordered locale-independent Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: Update to version 5.15.33-1Hauke Mehrtens2022-04-1033-439/+85
| | | | | | | | | | | | | | This updates mac80211 to version 5.15.33-1 which is based on kernel 5.15.33. The removed patches were applied upstream. This new release contains many fixes which were merged into the upstream Linux kernel. This also contains the following new drivers which are needed for ath11k: * net/qrtr/ * drivers/bus/mhi/ Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-12 22:38:48 +0000