aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Alcatel HH40VAndreas Böhler2023-04-235-0/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Alcatel HH40V is a CAT4 LTE router used by various ISPs. Specifications ============== SoC: QCA9531 650MHz RAM: 128MiB Flash: 32MiB SPI NOR LAN: 1x 10/100MBit WAN: 1x 10/100MBit LTE: MDM9607 USB 2.0 (rndis configuration) WiFi: 802.11n (SoC integrated) MAC address assignment ====================== There are three MAC addresses stored in the flash ROM, the assignment follows stock. The MAC on the label is the WiFi MAC address. Installation (TFTP) =================== 1. Connect serial console 2. Configure static IP to 192.168.1.112 3. Put OpenWrt factory.bin file as firmware-system.bin 4. Press Power + WPS and plug in power 5. Keep buttons pressed until TFTP requests are visible 6. Wait for the system to finish flashing and wait for reboot 7. Bootup will fail as the kernel offset is wrong 8. Run "setenv bootcmd bootm 0x9f150000" 9. Reset board and enjoy OpenWrt Installation (without UART) =========================== Installation without UART is a bit tricky and requires several steps too long for the commit message. Basic steps: 1. Create configure backup 2. Patch backup file to enable SSH 3. Login via SSH and configure the new bootcmd 3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work) More detailed instructions will be provided on the Wiki page. Tested by: Christian Heuff <christian@heuff.at> Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ath79: use gpios for switch management in WZR-HP-G300NH variantsTony Ambardar2023-04-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | The RTL8366S/RB switch node in DTS defines "mii-bus = <&mdio0>" to permit management via SMI but this has likely never worked, instead falling back to using GPIOs in the past: rtl8366s switch: cannot find mdio bus from bus handle (yet) rtl8366s switch: using GPIO pins 19 (SDA) and 20 (SCK) rtl8366s switch: RTL8366 ver. 1 chip found Recently, the rtl8366s and rtl8366_smi drivers were changed from built-in to loadable modules. This affected driver probing order and caused switch initialization (and network access) to fail: rtl8366s switch: using MDIO bus 'ag71xx_mdio' rtl8366s switch: unknown chip id (ffff) rtl8366s switch: chip detection failed, err=-19 Force using GPIOs to manage the switch by dropping the "mii-bus" DTS definition, which works for both built-in and loadable switch drivers. Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module") Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module") Tested-by: Tony Ambardar <itugrok@yahoo.com> # WZR-HP-G300NH (RTL8366S) Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: fix switch support for WZR-HP-G300NH devicesTony Ambardar2023-04-231-1/+2
| | | | | | | | | | | | Switch drivers for RTL8366S/RB were packaged as modules but not properly added to device definitions for WZR-HP-G300NH router variants, breaking network access to both after installation or upgrade. Assign the correct switch driver package for each router. Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module") Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* hostapd: update to 2023-03-29Nick Hainke2023-04-2254-587/+504
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add patches: - 170-wpa_supplicant-fix-compiling-without-IEEE8021X_EAPOL.patch Remove upstreamed: - 170-DPP-fix-memleak-of-intro.peer_key.patch - 461-driver_nl80211-use-new-parameters-during-ibss-join.patch - 800-acs-don-t-select-indoor-channel-on-outdoor-operation.patch - 992-openssl-include-rsa.patch Automatically refreshed: - 011-mesh-use-deterministic-channel-on-channel-switch.patch - 021-fix-sta-add-after-previous-connection.patch - 022-hostapd-fix-use-of-uninitialized-stack-variables.patch - 030-driver_nl80211-rewrite-neigh-code-to-not-depend-on-l.patch - 040-mesh-allow-processing-authentication-frames-in-block.patch - 050-build_fix.patch - 110-mbedtls-TLS-crypto-option-initial-port.patch - 120-mbedtls-fips186_2_prf.patch - 140-tests-Makefile-make-run-tests-with-CONFIG_TLS.patch - 150-add-NULL-checks-encountered-during-tests-hwsim.patch - 160-dpp_pkex-EC-point-mul-w-value-prime.patch - 200-multicall.patch - 300-noscan.patch - 310-rescan_immediately.patch - 330-nl80211_fix_set_freq.patch - 341-mesh-ctrl-iface-channel-switch.patch - 360-ctrl_iface_reload.patch - 381-hostapd_cli_UNKNOWN-COMMAND.patch - 390-wpa_ie_cap_workaround.patch - 410-limit_debug_messages.patch - 420-indicate-features.patch - 430-hostapd_cli_ifdef.patch - 450-scan_wait.patch - 460-wpa_supplicant-add-new-config-params-to-be-used-with.patch - 463-add-mcast_rate-to-11s.patch - 465-hostapd-config-support-random-BSS-color.patch - 500-lto-jobserver-support.patch - 590-rrm-wnm-statistics.patch - 710-vlan_no_bridge.patch - 720-iface_max_num_sta.patch - 730-ft_iface.patch - 750-qos_map_set_without_interworking.patch - 751-qos_map_ignore_when_unsupported.patch - 760-dynamic_own_ip.patch - 761-shared_das_port.patch - 990-ctrl-make-WNM_AP-functions-dependant-on-CONFIG_AP.patch Manually refresh: - 010-mesh-Allow-DFS-channels-to-be-selected-if-dfs-is-ena.patch - 301-mesh-noscan.patch - 340-reload_freq_change.patch - 350-nl80211_del_beacon_bss.patch - 370-ap_sta_support.patch - 380-disable_ctrl_iface_mib.patch - 464-fix-mesh-obss-check.patch - 470-survey_data_fallback.patch - 600-ubus_support.patch - 700-wifi-reload.patch - 711-wds_bridge_force.patch - 740-snoop_iface.patch Tested-by: Packet Please <pktpls@systemli.org> [Fritzbox 4040 (ipq40xx), EAP225-Outdoor (ath79); 802.11s, WPA3 OWE, and WPA3 PSK] Tested-by: Andrew Sim <andrewsimz@gmail.com> [mediatek/filogic] Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: fix lzma-loader for buffalo_WSR_600DHPHaoan Li2023-04-231-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #11919 Signed-off-by: Haoan Li <lihaoan1001@163.com>
* bmips: shg2500: add BCM4360 fallback SPROMÁlvaro Fernández Rojas2023-04-232-2/+16
| | | | | | | | Apart from the embedded BCM63268 wireless, this device has an external BCM4360 connected by PCIe which needs a fallback SPROM. b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700v2: add b43 wireless driverÁlvaro Fernández Rojas2023-04-231-0/+1
| | | | | | | | Apart from the embedded BCM6362 wireless, Netgear DGND3700v2 has external BCM43228 wireless connected by PCIe. Fallback SPROM isn't needed for this one because it has a physical SPROM. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: leds-sercomm-msp430: improve driverÁlvaro Fernández Rojas2023-04-231-3/+7
| | | | | | | - Add missing module functions. - Fix infinite pattern trigger by converting negative values to 0. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: enet: add missing module functionsÁlvaro Fernández Rojas2023-04-232-3/+14
| | | | | | | | | - Add missing MODULE_DEVICE_TABLE(). - Switch bcm6348-iudma to module_platform_driver(). - Add missing MODULE_AUTHOR, MODULE_DESCRIPTION, MODULE_LICENSE and MODULE_ALIAS. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: pci: use standard module functionsÁlvaro Fernández Rojas2023-04-233-24/+21
| | | | | | | late_initcall_sync() is no longer needed so standard module functions can be used on all bmips PCI/PCIe drivers. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mac80211: b43: only enable bcma or ssb on bmipsÁlvaro Fernández Rojas2023-04-231-2/+2
| | | | | | | | | By default both kmod-bcma and kmod-ssb are selected by kmod-b43. However, only one of both modules is needed for bmips subtargets: - bcma: bcm6318, bcm6328, bcm6362, bcm63268 - ssb: bcm6358, bcm6368 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: drop custom b43-sprom fixupsÁlvaro Fernández Rojas2023-04-232-1199/+0
| | | | | | b43-sprom fixups and no longer used and can be removed from bmips targets. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: switch to generic bcma/ssb fallback SPROMÁlvaro Fernández Rojas2023-04-2312-64/+12
| | | | | | | | Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback SPROMs. This way we don't need to include the b43-sprom fixups on devices without Broadcom wireless. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: add bcma/ssb fallback SPROM supportÁlvaro Fernández Rojas2023-04-237-3/+1843
| | | | | | | This adds generic kernel support for Broadcom Fallback SPROMs so that it can be used in any target, even non Broadcom ones. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* broadcom-sprom: add new packageÁlvaro Fernández Rojas2023-04-231-0/+295
| | | | | | | This adds a new package with Broadcom SPROMs that can be used as fallback when the devices lack physical SPROMs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* generic: 5.15: replace ramips AR8033 fiber patch with 5.18 patchesDaniel Kestrel2023-04-225-184/+375
| | | | | | | | | | | | A patch was added in kernel 5.4 to support the fiber operation of AR8033 with ramips devices. In kernel 5.18 similar enhancements were added to the kernel. Those patches are required for other fiber based devices but when added, build fails for ramips targets. This commit removes the ramips patch and adds the kernel 5.18 ones. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de> [ split commit,refresh patch and improve commit message ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: 5.10: replace ramips AR8033 fiber patch with 5.18 patchesDaniel Kestrel2023-04-226-184/+456
| | | | | | | | | | | | A patch was added in kernel 5.4 to support the fiber operation of AR8033 with ramips devices. In kernel 5.18 similar enhancements were added to the kernel. Those patches are required for other fiber based devices but when added, build fails for ramips targets. This commit removes the ramips patch and adds the kernel 5.18 ones. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de> [ split commit, refresh patch and improve commit title ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: 5.10: replace pending 730-net-phy-at803x-fix... with upstreamChristian Marangi2023-04-2210-32/+34
| | | | | | | | | Replace pending 730-net-phy-at803x-fix-feature-detection.patch with upstream version and move it to backport. Refresh other related patch while moving it. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* CI: check-kernel-patches: upload proposed refreshed patchesChristian Marangi2023-04-221-2/+16
| | | | | | | | | | | Upload proposed refreshed patches if the check fails. This should help devs refresh the patches if they don't have access to a buildroot. Devs should ALWAYS refresh the patches before submitting and merging commits. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: refresh 729-net-phy-realtek-introduce-rtl822x_probe.patchDaniel Golle2023-04-221-7/+7
| | | | | | | The patch needs to be refreshed to apply cleanly. Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for TP-Link TL-XDR4288/608xChukun Pan2023-04-228-4/+543
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: ESMT F50L1G41LB 128MB RAM: ESMT M15T4G16256A 512MB Ethernet (Max Speed): XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan WiFi: XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R) XDR6086/XDR6088: WiFi1: MT7976GN 2.4GHz 4T4R WiFi2: MT7976AN 5GHz 4T4R Button: Reset, WPS, Turbo USB: 1 x USB 3.0 Power: DC 12V 4A Flash instructions: 1. Execute the following operation to open nc shell: https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting 2. Replace the stock bootloader to OpenWrt's: dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip 3. Connect to your PC via the Gigabit port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 4. Download the initramfs image, and restart the router, waiting for tftp recovery to complete. 5. After openwrt boots up, perform sysupgrade. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> [Add uboot build, fit and sysupgrade support, fix RealTek PHYs] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add TP-Link TL-XDR4288 and TL-XDR608xDaniel Golle2023-04-223-0/+971
| | | | | | | | | | | | | | | | TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build for replacement loader for both TL-XDR6086 and TL-XDR6088. The only difference at U-Boot level is the different filename requested via TFTP, matching the corresponding OpenWrt build artifacts for each device. The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088 except for the wireless part. Also create a uboot for the TP-Link TL-XDR4288. Signed-off-by: Daniel Golle <daniel@makrotopia.org> [rebase to uboot 23.04, correct led and button] Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* kernel: net: phy: realtek: improve RealTek 2.5G PHY driverDaniel Golle2023-04-228-31/+251
| | | | | | | | | | | | | | | | | | | | * use interface mode switching only when operating in C45 mode Linux prevents switching the interface mode when using C22 MDIO, hence use rate-adapter mode in case the PHY controlled via C22. * use phy_read_paged where appropriate * use existing generic inline functions to handle 10GbE advertisements instead of redundantly defining register macros in realtek.c which are not actually vendor-specific. * make sure 10GbE advertisement is valid, preventing false-positive warning "Downshift occurred from negotiated speed 2.5Gbps to actual speed 1Gbps, check cabling!" with some link-partners using 1G mode. * Support Link Down Power Saving Mode (ALDPS) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* libpcap: update to 1.10.4Nick Hainke2023-04-221-2/+2
| | | | | | | Changes: https://git.tcpdump.org/libpcap/blob/104271ba4a14de6743e43bcf87536786d8fddea4:/CHANGES Signed-off-by: Nick Hainke <vincent@systemli.org>
* tools/isl: update to 0.26Nick Hainke2023-04-221-2/+2
| | | | | | | Changelog: https://repo.or.cz/isl.git/blob/e58af07f91c94db81627fb801fa6f52c3a7201a8:/ChangeLog Signed-off-by: Nick Hainke <vincent@systemli.org>
* tools/libressl: update to 3.7.2Nick Hainke2023-04-221-2/+2
| | | | | | | Release Notes: https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.7.2-relnotes.txt Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: bump 5.10 to 5.10.178John Audia2023-04-2219-112/+43
| | | | | | | | | | | Removed upstreamed: backport-5.10/430-v6.3-ubi-Fix-failure-attaching-when-vid_hdr-offset-equals.patch[1] 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.178&id=0279e82e148407feec88466990de14bcba9e12c0 All other patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.108John Audia2023-04-2226-197/+43
| | | | | | | | | | | | | | | | | Removed upstreamed: backport-5.15/430-v6.3-ubi-Fix-failure-attaching-when-vid_hdr-offset-equals.patch[1] backport-5.15/612-v6.3-skbuff-Fix-a-race-between-coalescing-and-releasing-S.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=85d7a7044b759d865d10395a357632af00de5867 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=906a6689bb0191ad2a44131a3377006aa098af59 Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* generic: update nvmem cell mac-address-ascii supportChukun Pan2023-04-212-42/+52
| | | | | | | | Instead of use mac-address-ascii in nvmem_get_mac_address function, move it into of_get_mac_addr_nvmem function to support more devices. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: MSG1500 X.00: switch to mac-address-ascii dtsChukun Pan2023-04-213-17/+30
| | | | | | | | The Config partition of some machines is special, and the openwrt script cannot read the protest_lan_mac correctly. This problem can be solved by reading the mac address (ascii) in dts. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: remove redundant code for tuf-ax4200Chukun Pan2023-04-211-2/+1
| | | | | | Remove redundant code in 02_network. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: move mac address setting togetherChukun Pan2023-04-211-4/+6
| | | | | | Simultaneously sort in the order of letters. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: fix network config for mt7986a-rfbChukun Pan2023-04-211-1/+3
| | | | | | | Fix the network configuration according to the device tree. Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* tools/squashfs4: backport OpenWrt extended options patchChristian Marangi2023-04-203-1/+900
| | | | | | | | | | | | | Due to us keeping a patch around for years and never proposing it to squashfs4 repository, we resulted in having the same squashfs4 version but with different supported options. (openwrt patched -- upstream) To workaround this problem, a non-standard option was required. To not have surprise on tool bump, backport the patch and add the new config option required to enable these extended non-standard options. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ksmbd: update to latest 3.4.8 releaseAndrew Sim2023-04-201-2/+2
| | | | | | Changelog: https://github.com/cifsd-team/ksmbd/releases/tag/3.4.8 Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
* tools/lz4: build with mesonRosen Penev2023-04-202-23/+12
| | | | | | | | | | | | | | | | Simplifies Makefile and speeds up compilation. Before: Executed in 68.00 secs fish external usr time 104.17 secs 1.33 millis 104.17 secs sys time 4.29 secs 0.35 millis 4.29 secs After: Executed in 27.98 secs fish external usr time 25.18 secs 1.32 millis 25.18 secs sys time 3.31 secs 0.35 millis 3.31 secs Signed-off-by: Rosen Penev <rosenp@gmail.com>
* uboot-mediatek: fix factory/reset buttonDaniel Golle2023-04-2013-22/+110
| | | | | | | | | | | U-Boot commit ea6fdc13595 ("dm: button: add support for linux_code in button-gpio.c driver") makes it mandatory to specify linux,code for all buttons. As that broke handling of the reset button in U-Boot with the update to U-Boot 2023.04, add linux,code for all butons. Reported-by: @DragonBluep Fixes: 50f7c5af4a ("uboot-mediatek: update to v2023.04") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: update kernel config-5.15Daniel Golle2023-04-201-1/+4
| | | | | | | Expose thermal-zone as hwmon sensor, remove thermal emulation driver and add some missing symbols. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r3: allow up to 3W per SFP moduleDaniel Golle2023-04-201-0/+2
| | | | | | | | | According to SinoVoip up to 3A @ 3.3V are available for both SFP modules together. Raise energy limit from 1W (default) to 3W, however, be aware that using modules consuming more than 1W will require active cooling! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* tools/dwarves: update to 1.25Nick Hainke2023-04-191-5/+3
| | | | | | | | | Remove AUTORELEASE and HOST_BUILD_PARALLEL. Release Notes: https://lore.kernel.org/dwarves/ZDG4qxirpIfmbiip@kernel.org/T/#u Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: fix up qrtr packaging after 5.15.107 bumpStefan Lippers-Hollmann2023-04-191-2/+1
| | | | | | | | qrtr/ns.ko is now merged into qrtr/qrtr.ko, so drop the individual module packaging. Fixes: f4989239cc91 ("kernel: bump 5.15 to 5.15.107") Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, mt7621/dap-x1860
* kernel: bump 5.15 to 5.15.107John Audia2023-04-1910-20/+20
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* tools/cmake: update to 3.26.3Nick Hainke2023-04-191-2/+2
| | | | | | | | | Release Notes: - https://www.kitware.com/cmake-3-26-1-available-for-download/ - https://www.kitware.com/cmake-3-26-2-available-for-download/ - https://www.kitware.com/cmake-3-26-3-available-for-download/ Signed-off-by: Nick Hainke <vincent@systemli.org>
* mwlwifi: update to version 10.3.9.0-20230311Kabuli Chana2023-04-196-133/+19
| | | | | | | | | | | | | upstream PR 408 improvements: -Fix AMSDU packets unused -Removed the ASMDU packets queue -Add more info in the iw tool -fix is_hw_crypto_enabled -Optimization AMPDU_TX_OPERATIONAL (avoid a spinlock) change to wongsyrone mod Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* bmips: pci-bcm6348: load IO resource from DT rangesÁlvaro Fernández Rojas2023-04-183-28/+14
| | | | | | Correctly load IO resource from DT ranges and remove the specific IO resource. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: drop unneeded ath9k fixupÁlvaro Fernández Rojas2023-04-182-243/+1
| | | | | | | We no longer need the custom ath9k fixup now that we're using the standard kmod-owl-loader. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: hg556a: switch to kmod-owl-loaderÁlvaro Fernández Rojas2023-04-183-14/+66
| | | | | | Stop using custom ath9k fixup and switch to standard kmod-owl-loader Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* tools/bzip2: add `bzip2` binariesTony Butler2023-04-184-0/+484
| | | | | | | | | | | | | | | `bzip2` is the standard executable for bzip2 compression this includes development includes and both static and shared libs (libbz2) which can be used by other packages the initramfs generator offers the BZIP2 option but there was no executable to support it, and worked only via side effect of having a system-installed version of bzip2, which could be less predictable Signed-off-by: Tony Butler <spudz76@gmail.com> [ remove unintended change ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* Revert "tools/bzip2: add `bzip2` binaries"Christian Marangi2023-04-184-484/+1
| | | | | | | | | This reverts commit 394d7134ec42f14ddb91769c737098753fa68266. The commit has unintentded change that cause compilation error with SDK or LZO compression. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mac80211: ath11k: replace 160MHz fix with upstream pending oneRobert Marko2023-04-183-31/+132
| | | | | | | | QCA has finally sent a proper fixup for the 160MHz regression upstream, so lets use the pending fix which also properly sets center frequency 2 in case 80+80 MHz is used. Signed-off-by: Robert Marko <robimarko@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-28 10:18:00 +0000