aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* realtek: do not reset SerDes on link changeBirger Koblitz2022-05-112-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Do not reset the RTL930x SerDes on link changes, instead set up the SDS with internal PHYs for the SFP+ ports only. This fixes the 8 1GBit ports on the Zyxel XGS1250 which do not work without this patch. A complete SerDes reset was performed on all SerDes links. For copper 1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There is however no support for setting up the XGMII link on RTL9300/RTL9310, thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit ports. No SerDes reset should be done for these links. The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely different. All these modes need to be suitably RX calibrated and the pre- main and post- amplifiers set up properly for TX. The 10GBit SFP+ fiber links are recalibrated instead of reset, which e.g. is necessary when someone pulls a module out and puts another in. This makes swapping out 10GBit fiber modules possible. 1GBit modules are not yet supported, nor any modules with an internal phy. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Birger Koblitz <git@birger-koblitz.de> [rewrite commit message based on discussion] Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html Signed-off-by: Sander Vanheule <sander@svanheule.net>
* kernel: bump 5.15 to 5.15.38Rui Salvaterra2022-05-097-101/+13
| | | | | | | | | | | Deleted (upstreamed): mediatek/patches-5.15/120-10-v5.18-mtd-nand-fix-ecc-parameters-for-mt7622.patch [1] Other patches automatically rebased. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.38&id=3ec920d755ae69c201b358e8d8e96c32f51145d8 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.37Rui Salvaterra2022-05-092-3/+3
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.36Rui Salvaterra2022-05-0912-28/+28
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-093-0/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net>
* realtek: Trap all frames with switch as destination to CPU-portBirger Koblitz2022-05-081-0/+9
| | | | | | | | | | | | This fixes a bug where frames sent to the switch itself were flooded to all ports unless the MAC address of the CPU-port was learned otherwise. Tested-by: Wenli Looi <wlooi@ucalgary.ca> Tested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Birger Koblitz <git@birger-koblitz.de> [fix code formatting] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: add support for ZyXEL GS1900-16Raylynn Knight2022-05-073-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-16 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE * Ethernet: 16x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 16 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J12) with populated standard pin connector on the right back of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin file amd select open so File Path is update with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-16 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight <rayknight@me.com> [removed duplicate patch title, align RAM specification] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* kernel: backports: add Huawei MA5671A tx-fault workaroundMatthew Hagan2022-05-072-0/+114
| | | | | | | | | This workaround will allow the MA5671A to function, ignoring the persistently asserted tx-fault. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com> (added 5.15 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for kernel 5.15 for testingChristian Lamparter2022-05-077-0/+536
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch copies over refreshed config and patches from 5.10 with the following changes: - dropped superfluous tc654/tc655 variant detection patch (tc654 support will become available upstream starting with 5.17-rc7+). - dropped xhci msi(x) workaround... as the broken MSI(X) is now gone. - dropped dwc2 workaround since the driver was fixed and it works without it. Please note: Netgear WNDAP660 & WNDAP620 users: Due to the kernel's size increase, uboot will likely break because it is overwrite the kernel during decompression. To fix this (and debrick affected devices, no reflash necessary), attach the RJ45-Serial-Console cable and enter the following in the uboot prompt during bootup: setenv kernel_addr_r 1100000 saveenv run bootcmd to restore the old/previous behavior: setenv kernel_addr_r 600000 saveenv run bootcmd Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: usb-xhci-pci-renesas: remove LINUX_5_10 dependency symbolChristian Lamparter2022-05-071-1/+0
| | | | | | | | With 5.4 out of the picture, remove LINUX_5_10 here. This is needed for the WNDR4700 as otherwise kmod-usb3 isn't available for 5.15. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: 5.15: add missing symbolChristian Lamparter2022-05-071-0/+1
| | | | | | Found during apm821xx refresh. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel/x86: move x86' specific watchdogs to the x86 targetChristian Lamparter2022-05-072-65/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | upstream linux have these watchdogs locked behind X86. These will not build on other architectures. So move them to target/linux/x86/modules.mk drivers/watchdog/Kconfig: |config F71808E_WDT | tristate "Fintek F718xx, F818xx Super I/O Watchdog" | depends on X86 |[...] |config IT87_WDT | tristate "IT87 Watchdog Timer" | depends on X86 |[...] |config ITCO_WDT | tristate "Intel TCO Timer/Watchdog" | depends on (X86 || IA64) && PCI |[...] |config W83627HF_WDT | tristate "Watchdog timer for W83627HF/W83627DHG and compatibles" | depends on X86 |[...] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: detangle meraki-mx100 / nu801 build confusionChristian Lamparter2022-05-071-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Grommish reported the dreaded build error that happend with 5.4 since the kernel didn't have the cgpio v2 interface. His reason for the removed 5.4 was that the octeon target had a memory leak issue, so he had to backport the removed 5.4 kernel for his tests. Chen Minqiang chimed in and noted that no matter what (i.e. @TARGET_x86 in depends) didn't prevent the package from being build on other targets. From what I can tell, the reason for this was that +nu801 meant that kmod-meraki-mx100 pulled in an unconditional dependency as part of to the kernel build. |scripts/package-metadata.pl mk tmp/.packageinfo | |$(curdir)/kernel/linux/compile += $(curdir)/firmware/linux-firmware/compile \ | $(curdir)/firmware/prism54-firmware/compile \ | $(curdir)/kernel/gpio-button-hotplug/compile \ | >>> $(curdir)/system/gpio-cdev/nu801/compile <<< change this by making the dependency conditional on the meraki-mx100 module itself. Note that the nu801 enables/sets the KCONFIG for the cgpio v2 interface itself, since the userspace program and not the kernel meraki-mx100 relies on it. Reference: <https://github.com/openwrt/openwrt/commit/eeb8fd4ce7e9> Reported-by: Grommish <grommish@gmail.com> Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: add ib700wdt module for x86 qemu watchdogsChristian Lamparter2022-05-071-0/+18
| | | | | | | | QEMU+Libvirt can emulate the ib700wdt watchdogs which due to its I/O-Port mapping makes it x86 specific. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* armvirt: 64: enable driver for QEMU' supported watchdogChristian Lamparter2022-05-072-0/+4
| | | | | | | | | | | | QEMU can emulate several watchdogs: aspeed SoC, i6300esb, ib700wdt, imx2, cmsdk-apb and sbsa_gwdt. Out of these, the ARM SBSA Generic Watchdog (sbsa_gwdt) makes the most sense for the armvirt' 64 target. Both imx2 and aspeed are guarded by special vendor specific CONFIG_ in the upstream kernel. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: provide i6300esb for qemu/libvirtChristian Lamparter2022-05-071-0/+18
| | | | | | | | | | the Intel i6300esb is QEMU's default watchdog. And unlike the real "Intel i6300ESB I/O Controller hub" hardware, the i6300esb watchdog driver works on non-x86 targets like for ARM (armvirt 32bit) and potentially virtual PowerPC and MIPS targets (if there was any). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: fix corrupted padding on small packets with mt753x dsaFelix Fietkau2022-05-062-0/+58
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport flow offload fixes to 5.10Felix Fietkau2022-05-066-150/+413
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix flow offload issues with pppoeFelix Fietkau2022-05-065-150/+368
| | | | | | sync xt_FLOWOFFLOAD code with latest version of nft_flow_offload Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: consolidate ar40xx driver filesSungbo Eo2022-05-054-2235/+0
| | | | | | | | | | Commit f4fb63d2ab4f ("ipq40xx: 5.10: move AR40xx to MDIO drivers") moved the ar40xx driver files to kernel version specific directories to place them in different subdirectory in kernel tree. But now kernel 5.4 is gone and there is no reason to keep them separate. Move them back to common files/ directory. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: 5.15: fix ar40xx driverNick Hainke2022-05-051-0/+3
| | | | | | | | | | | | | | | | Also apply commit ab7e53e5cce7 ("ipq40xx: 5.10: fix ar40xx driver") to 5.15 driver. The commit fixes the data corruption on TX packets. Packets are transmitted, but their contents are replaced with zeros. This error is caused by the lack of guard (50 ms) intervals between calibration phases. This error is treated by adding mdelay(50) to the calibration function code. In the original qca-ssda code, these mdelays were existing, but in the ar41xx.c they are gone. Fixes: 87318eb17936 ("ipq40xx: 5:15: copy config and patch from 5.10") Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: add i2c in dts for GL-MT300N-V2Ptilopsis Leucotis2022-05-051-0/+4
| | | | | | | | According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/ GL-MT300N-V2 have I2C interface on GPIO4, GPIO5. Adding I2C in device tree make possible using I2C on this device. Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
* ipq806x: add support for Arris TR4400 v2 / RAC2V1ARodrigo Balerdi2022-05-057-3/+450
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specs: SoC: Qualcomm IPQ8065 (dual core Cortex-A15) RAM: 512 MB DDR3 Flash: 256 MB NAND, 32 MB NOR WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz Switch: QCA8337 Ethernet: 5x 10/100/1000 Mbit/s USB: 1x USB 3.0 Type-A Buttons: WPS, Reset Power: 12 VDC, 2.5 A Ethernet ports: 1x WAN: connected to eth2 4x LAN: connected via the switch to eth0 and eth1 (eth0 is disabled in OEM firmware) MAC addresses (OEM and OpenWrt): fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1) fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2) fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1) fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0) fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt) OID d4:ab:82 is registered to: ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US More info: https://openwrt.org/inbox/toh/arris/tr4400_v2 IMPORTANT: This port requires moving the 'fw_env' partition prior to first boot to consolidate 70% of the usable space in flash into a contiguous partition. 'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords. Its contents must be copied to 'rootfs_1' prior to booting via initramfs. Note that the stock 'fw_env' partition will be wiped during sysupgrade. A writable 'stock_fw_env' partition pointing to the old, stock location is included in the port to help rolling back this change if desired. Installation: - Requires serial access and a TFTP server. - Fully boot stock, press ENTER, type in: mtd erase /dev/mtd21 dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21 umount /config && ubidetach -m 23 && mtd erase /dev/mtd23 - Reboot and interrupt U-Boot by pressing a key, type in: set mtdids 'nand0=nand0' set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)' set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm' env save - Setup TFTP server serving initramfs image as 'recovery.bin', type in: set ipaddr 192.168.1.1 set serverip 192.168.1.2 tftpboot recovery.bin && bootm - Use sysupgrade to install squashfs image. This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> [add 5.15 changes for 0069-arm-boot-add-dts-files.patch] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* packages: nvram: add NVRAM quirks for bcm53xx targetArınç ÜNAL2022-05-044-17/+48
| | | | | | | | | | | Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U. Use boot() instead of start() as nvram commands are meant to be executed only once, at boot. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* firewall: config: remove restictions on DHCPv6 allow ruleTiago Gaspar2022-05-042-4/+2
| | | | | | | | | | | | | | Remove restrictions on source and destination addresses, which aren't specified on RFC8415, and for some reason in openwrt are configured to allow both link-local and ULA addresses. As cleared out in issue #5066 there are some ISPs that use Gloabal Unicast addresses, so fix this rule to allow them. Fixes: #5066 Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com> [rebase onto firewall3, clarify subject, bump PKG_RELEASE] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ltq-vdsl-app: disconnect when service is stoppedJan Hoffmann2022-05-043-3/+78
| | | | | | | | | | | | | | Stop the connection when the control daemon is terminated. The code is a modified version of the termination routine in version 4.23.1 of the daemon (which doesn't support VR9 modems anymore). This could also be implemented by calling the acos and acs commands via dsl_cpe_pipe.sh in the init script. However, doing it in the daemon itself has the advantage of also working if it is terminated in another way (for example during sysupgrade). Signed-off-by: Jan Hoffmann <jan@3e8.eu> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ltq-vdsl/ltq-adsl: fix elapsed time calculationJan Hoffmann2022-05-044-2/+246
| | | | | | | | | | | | | | | | | | | The driver maintains elapsed times by repeatedly accumulating the time since the previous update in a loop. For the elapsed showtime time, the time difference is truncated to seconds before adding it, leading to a sizable error over time. Move the truncation to before calculation of the time difference in order to remove this error. Also maintain the total elapsed time in the same way in full seconds, to prevent the unsigned 32-bit counter from wrapping around after about 50 days. Testing on a VR9 device shows that the reported line uptime now matches the actual elapsed wall time. The ADSL variant is only compile-tested, but it should also work as the relevant code is identical. Signed-off-by: Jan Hoffmann <jan@3e8.eu> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ltq-atm/ltq-ptm: avoid unnecessary build dependenciesJan Hoffmann2022-05-042-6/+11
| | | | | | | | | | | | | Right now, both ltq-adsl-mei and ltq-vdsl-mei are always built, even when they aren't necessary for the selected variant. This can cause the build to fail, for example ltq-vdsl-mei doesn't build successfully here on xway target due to the vectoring callback. Make these dependencies conditional on the specific package variants, so they are only built when actually needed. Signed-off-by: Jan Hoffmann <jan@3e8.eu> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* uqmi: update to git HEADDaniel Golle2022-05-041-3/+3
| | | | | | | 56cb2d4 nas: add decoding of cell_id 9a9019a uqmi: wms - added storage to read text messages Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* fstools: update to git HEADDaniel Golle2022-05-031-3/+3
| | | | | | 9e11b37 fstools: remove SELinux restorecon hack Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2022-05-031-3/+3
| | | | | | 652e6df init: restore SELinux labels after policy is loaded Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* base-files: simplify restorecon logicDaniel Golle2022-05-021-2/+2
| | | | | | | | | Remove forgotten redundant selinuxenabled call and skip the whole thing in case $IPKG_INSTROOT is set as labels are anyway applied only later on in fakeroot when squashfs is created. Fixes: 6d7272852e ("base-files: add missing $IPKG_INSTROOT to restorecon call") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* selinux-policy: update to version 1.1Dominick Grift2022-05-021-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | try to clean up some labeling inconsistencies iwinfo loose ends ucode loose ends Makefile: adjust mintesttgt (adds blockmount/blockd) nftables: reads inherited netifd pipe ucode: reads inherited netifd pipes mountroot: fowner sandbox: writes inherited dropbear pipes unbound related to /tmp/etc/ssl unbound loose ends adds a sslconftmpfile for /tmp/etc/ssl README: maintain a wish list in the README iwinfo: netifd forgot write gptfdisk loose ends iwinfo: netifd wpad reads/writes inherited netifd fifo files netifd (mac80211.sh) executes iwinfo luci: executes wireguard luci-cgi: audits xtables execute access rcuhttpd: lists ssl certfile dirs iwinfo, wifi,nftables usage of ttyd pty if available urandomseed: seedrng needs cap_sys_admin iwinfo iwinfo, nftables and some chronyd rules related to ntp nts server nftables, wifi and adds iwinfo skel nftables, rpcd, ucode nftables, ucode and seedrng ucode, fw3/nftables, luci adds ucode skel and some fw3/nftables related urandomseed: some seedrng rules fw3 adds some support for fw4 urandomseed: /etc/seedrng is for seed.credit hotplugcal: runs ucode which is interpreter like adds a nftables skeleton and makes xtables optional agent: allow all agents to write inherited dropbear pipes urandomseed: this seems to be replaced by seedrng kmodloader: label /etc/modules.conf kmodloader.conffile Revert "shelexecfile: remove auditallow rule" Makefile: sort the modules to process by secilc Moves back to git.defensec.nl unbound odhcpd (ip) reads net proc tcp dump shelexecfile: remove auditallow rule rrd.cil: fixes indent Target rddtool from cgi-io instead of runnit it without transition rrd.cil related rrd, rpcd, cgiio clean ups related to luci-app-statistics Rules for rrd files and luci-statistics unboundcontrol ordering Several missing permissions blockmount, dnsmasq, hotplugcall, rpcd, unbound adds mctp_socket (linux 5.15) ip: forgot tc-tiny type transition to go along with the fc spec ip: adds a fc spec for tc-tiny (called by sqm) adds ttyACM fc spec and various assorted loose ends .gitattributes: do not export the github workflows workflow use selinux 3.3 project moved back to https://git.defensec.nl/selinux-policy.git Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
* ipq40xx: fix BDF file for pcie wifi chip on the GL.Inet GL-B2200Enrico Mioso2022-05-021-0/+0
| | | | | | | | | | | | | | | | | | | | | | After the switch to pre-calibration, ath10k would fail to initialize the PCIE Wi-Fi on the GL-B200 as follows: ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000 [...] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=GL-B2200 from ath10k/QCA9888/hw2.0/board-2.bin ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0 ath10k_pci 0000:01:00.0: failed to fetch board file: -12 ath10k_pci 0000:01:00.0: could not probe fw (-12) Repackage the BDF file after renaming relevant fields and files to allow for the Wi-Fi interface to start again. Fixes: 80d34d9d593 ("ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200") CC: Christian Lamparter <chunkeey@gmail.com> CC: Robert Marko <robimarko@gmail.com> Reviewed-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
* base-files: add missing $IPKG_INSTROOT to restorecon callDaniel Golle2022-05-021-1/+3
| | | | | | | Update to overlooked v2 version of Dominick Grift's patch. Fixes: 5109bd164c ("base-files: address sed in-place without SELinux awareness") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* dnsmasq: fix jail_mount for serversfileBruno Victal2022-05-021-1/+8
| | | | | | Fix 'serversfile' option not being jail_mounted by the init script. Signed-off-by: Bruno Victal <brunovictal@outlook.com>
* base-files: address sed in-place without SELinux awarenessDominick Grift2022-05-021-0/+1
| | | | | | | | | | | | sed(1) in busybox does not support this functionality: https://git.savannah.gnu.org/cgit/sed.git/tree/sed/execute.c#n598 This causes /etc/group to become mislabeled when a package requests that a uid/gid be added on OpenWrt with SELinux Signed-off-by: Daniel Golle <daniel@makrotopia.org> [move restorecon inside lock] Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
* base-files: fix sysupgrade for kernel-out-of-UBIRodrigo Balerdi2022-05-021-2/+6
| | | | | | | | | | | | | | | | | | | | Commit ecbcc0b59551 bricks devices on which the raw kernel and UBI mtd partitions overlap. This is the case of the ZyXEL NR7101 for example. Its OEM bootloader has no UBI support. OpenWrt splits the stock kernel mtd partition into a raw kernel part used by the bootloader and a UBI part used to store rootfs and rootfs_data. Running mtd erase on the complete partition during sysupgrade erases the UBI part and results in a soft brick. Arguably the best solution would be to fix the partition layouts so that kernel and UBI partitions do not overlap, also including a stock_kernel partition to help reverting to stock firmware. This would have the added benefit of protecting UBI from kernel images that are excessively large. Fixes: ecbcc0b59551 ("base-files: safer sysupgrade.tar for kernel-out-of-UBI") Reported-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* fstools: update to git HEADDaniel Golle2022-05-011-3/+3
| | | | | | | | | | | | | f0fc66a libfstools: check for overlay mounting errors 128ecaf Update / fix extroot comments 8a0ba3b libfstools: get rid of "extroot_prefix" global variable 649cd3f libfstools: use variable for overlay mount-point 922f1b3 libfstools: avoid segfault in find_mount_point ce5eacb libfstools: mtd: improve error handling 898b328 blockd: restore device_move semantics 0917d22 block: don't probe mtdblock on NAND (with legacy exceptions) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: ethernet: ralink: add led_source dts-bindingTamas Balogh2022-05-011-10/+17
| | | | | | | | | | | | | | | | | | | | this adds the new dts-binding "mediatek,led_source" currently for MT7628AN and MT7688 built-in switches, which is documented as a 3-bit field configuring the switch LEDs for various control schemes from 0 to 3. Normally this is not needed, but e.g. for Asus RT-AC1200-V2 it is a must to set it to the anyway undocumented value of 4, to have the switch LEDs react correctly on link/act events. This is an MT7628DAN device, but I doubt this is a speciality of this particular SoC. Also added the RT305X_ESW_LED_OFF value to LED states. Did also rename the register RT5350_EWS_REG_LED_POLARITY to RT5350_EWS_REG_LED_CONTROL, which is the correct name. Also making use of defines for some hardcoded values. Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* kirkwood: set testing kernel version to 5.15Pawel Dembicki2022-05-011-0/+1
| | | | | | | | | This patch configures kernel testing version for kirkwood target. Compile tested: all Run tested: Endian 4i Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: refresh 5.15 kernel configPawel Dembicki2022-05-011-5/+7
| | | | | | Done by "make kernel_oldconfig". Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* generic: 5.15: add missing symbolPawel Dembicki2022-05-011-0/+1
| | | | | | Found durring kirkwood refreshing. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: copy config and patches to 5.15Pawel Dembicki2022-05-0117-0/+1264
| | | | | | | | This patch makes only a copy of 5.10 config and patches. Patches merged in upstream was omited. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: 5.15: refresh subtarget configSungbo Eo2022-05-012-2/+2
| | | | | | Update config with `make kernel_oldconfig CONFIG_TARGET=subtarget`. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: 5.15: refresh configRobert Marko2022-05-011-13/+2
| | | | | | | Refresh 5.15 kernel config for IPQ40xx due to large number of generic config changes. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: 5.15: drop upstreamed sleep clock patchRobert Marko2022-05-011-26/+0
| | | | | | | Patch that corrects sleep clock frequency has already been backported to 5.15 stable so remove the duplicate patch. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: 5.15: add testing kernel versionAnsuel Smith2022-05-011-1/+1
| | | | | | | | | | | | | Add 5.15 kernel as a testing kernel version in the Makefile. Linksys EA6350v3/EA8300/MR8300 will not build with buildbot settings and should be disabled when the target is switched, unless the image size is reduced again. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Reviewed-by: Robert Marko <robert.marko@sartura.hr> [add comment for increased kernel size] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: 5.15: refresh kernel patchesAnsuel Smith2022-05-0113-26/+26
| | | | | | | Refresh kernel patches. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Reviewed-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: refresh ess driver and phy with new apiAnsuel Smith2022-05-012-0/+48
| | | | | | | | Kernel 5.15 have some new api for ethtool and phy. Add ifdef to fix compilation error. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Reviewed-by: Robert Marko <robert.marko@sartura.hr>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-29 19:43:44 +0000