aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx: enable NAND support for all subtargetsJosef Schlehofer2022-06-193-3/+1
| | | | | | | | | | | | | | In subtarget p2020, there wasn't enabled nand support, and because of that there weren't available tools from mtd-utils package, which has utilities for NAND flash memory even though reference board, which is the only currently supported device in p2020 subtarget has NAND [1]. All subtargets in mpc85xx has already enabled nand support, let's do it globally. [1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* kernel: Backport mv88e6xxx patch to keep pvid at 0 if VLAN-unaware and ↵Marek Behún2022-06-191-18/+0
| | | | | | | | | | | | | | | remove hack Keeping the pvid at 0 when VLAN-unaware makes it possible to drop the hack introduced in commit 920eaab1d817 ("kernel: DSA roaming fix for Marvell mv88e6xxx"). Dropping the hack makes it possible to use VLAN interfaces with VID 1 on DSA ports without problems with FDB. Signed-off-by: Marek Behún <kabel@kernel.org> (cherry picked from commit 9caa6f0aa742253901c72f43eebecd2c8da5f127) Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [drop kernel patch hack from Linux version 5.15, drop paragraph about backport patch, which is not necessary as it is included in kernel 5.15]
* bcm53xx: remove 07_set_preinit_iface_bcm53xxChristian Lamparter2022-06-191-14/+0
| | | | | | | | with the switch to DSA setup, the switch gets correctly programmed via the device-tree now. This hack is no longer necessary. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: move Toshiba-TC58NVG0S3H patch to ipq40xx reduxChristian Lamparter2022-06-192-12/+6
| | | | | | | | | | | | | | | | | | Linux' upstream MTD-Maintainer Miquèl Raynal noted: |Reverting seems the safest option here, not knowing how many devices |have these damaged/counterfeit chips. If it is just a couple and only on |Fritzboxes, as suggested in the Github issue this patch could be |carried through OpenWrt and that would seem more future proof IMHO. This patch follows up with the first patch. It actually moves the patches out of target/linux/generic/pending into the ipq40xx's patch heap and adds a little note what happend. For more information, discussions or reports about bad TC58NVG0S3Hs, please visit the OpenWrt's Github Issue #9962: <https://github.com/openwrt/openwrt/issues/9962> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* netfilter: kmod-nft-xfrmFlorian Eckert2022-06-192-0/+13
| | | | | | Add kmod-nft-xfrm package. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* realtek: add support for power LED on Netgear GS108Tv3Pascal Ernster2022-06-191-0/+27
| | | | | | | | | | | | | | | | | | | | | The Netgear GS108Tv3 is already supported by OpenWrt, but is missing LED support. After OpenWrt installation, all LEDs are off which makes the installation quite confusing. This enables support for the green/amber power LED to give feedback about the current status. This is basically just a verbatim copy of commit c4927747d25a ("realtek: add support for power LED on Netgear GS308Tv1"). Please note that both LEDs are wired up in an anti-parallel fashion, which means that only one of both LEDs/colors can be switched on at the same time. If both LEDs/colors are switched on simultanously, the LED goes dark. Tested-by: Pascal Ernster <git@hardfalcon.net> Signed-off-by: Pascal Ernster <git@hardfalcon.net> [add title to commit reference] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: add support for D-Link DGS-1210-20Markus Stockhausen2022-06-193-0/+111
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash * 16 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - External PHY with 8 ports (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [o]ooo|J6 | ||`------ GND | |`------- RX | `-------- TX `---------- Vcc (3V3) Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> [correct initramfs image name] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* rockchip: add kernel 5.15 as testingJuergen Wurzer2022-06-186-1/+763
| | | | | | | | Add kernel 5.15 as testing kernel for the rockchip-armv8 target. Signed-off-by: Juergen Wurzer <wurzer.juergen@gmail.com> [squash commits, update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix RT-AC57U button levelDavid Bauer2022-06-181-1/+1
| | | | | | | Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the WPS cutton to fix button behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: update to 2022-06-02David Bauer2022-06-182-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 4383528e0 P2P: Use weighted preferred channel list for channel selection f2c5c8d38 QCA vendor attribute to configure RX link speed threshold for roaming 94bc94b20 Add QCA vendor attribute for DO_ACS to allow using existing scan entries b9e2826b9 P2P: Filter 6 GHz channels if peer doesn't support them d5a9944b8 Reserve QCA vendor sub command id 206..212 ed63c286f Remove space before tab in QCA vendor commands e4015440a ProxyARP: Clear bridge parameters on deinit only if hostapd set them 02047e9c8 hs20-osu-client: Explicit checks for snprintf() result cd92f7f98 FIPS PRF: Avoid duplicate SHA1Init() functionality 5c87fcc15 OpenSSL: Use internal FIPS 186-2 PRF with OpenSSL 3.0 9e305878c SAE-PK: Fix build without AES-SIV c41004d86 OpenSSL: Convert more crypto_ec_key routines to new EVP API 667a2959c OpenSSL: crypto_ec_key_get_public_key() using new EVP_PKEY API 5b97395b3 OpenSSL: crypto_ec_key_get_private_key() using new EVP_PKEY API 177ebfe10 crypto: Convert crypto_ec_key_get_public_key() to return new ec_point 26780d92f crypto: Convert crypto_ec_key_get_private_key() to return new bignum c9c2c2d9c OpenSSL: Fix a memory leak on crypto_hash_init() error path 6d19dccf9 OpenSSL: Free OSSL_DECODER_CTX in tls_global_dh() 4f4479ef9 OpenSSL: crypto_ec_key_parse_{priv,pub}() without EC_KEY API b092d8ee6 tests: imsi_privacy_attr 563699174 EAP-SIM/AKA peer: IMSI privacy attribute 1004fb7ee tests: Testing functionality to discard DPP Public Action frames 355069616 tests: Add forgotten files for expired IMSI privacy cert tests b9a222cdd tests: sigma_dut and DPP curve-from-URI special functionality fa36e7ee4 tests: sigma_dut controlled STA and EAP-AKA parameters 99165cc4b Rename wpa_supplicant imsi_privacy_key configuration parameter dde7f90a4 tests: Update VM setup example to use Ubuntu 22.04 and UML 426932f06 tests: EAP-AKA and expired imsi_privacy_key 35eda6e70 EAP-SIM peer: Free imsi_privacy_key on an error path 1328cdeb1 Do not try to use network profile with invalid imsi_privacy_key d1652dc7c OpenSSL: Refuse to accept expired RSA certificate 866e7b745 OpenSSL: Include rsa.h for OpenSSL 3.0 bc99366f9 OpenSSL: Drop security level to 0 with OpenSSL 3.0 when using TLS 1.0/1.1 39e662308 tests: Work around reentrant logging issues due to __del__ misuse 72641f924 tests: Clean up failed test list in parallel-vm.py e36a7c794 tests: Support pycryptodome a44744d3b tests: Set ECB mode for AES explicitly to work with cryptodome e90ea900a tests: sigma_dut DPP TCP Configurator as initiator with addr from URI ed325ff0f DPP: Allow TCP destination (address/port) to be used from peer URI e58dabbcf tests: DPP URI with host info 37bb4178b DPP: Host information in bootstrapping URI 1142b6e41 EHT: Do not check HE PHY capability info reserved fields 7173992b9 tests: Flush scan table in ap_wps_priority to make it more robust b9313e17e tests: Update ap_wpa2_psk_ext_delayed_ptk_rekey to match implementation bc3699179 Use Secure=1 in PTK rekeying EAPOL-Key msg 1/4 and 2/4 d2ce1b4d6 tests: Wait for request before responding in dscp_response Compile-tested: all versions / ath79-generic, ramips-mt7621 Run-tested: hostapd-wolfssl / ath79-generic, ramips-mt7621 Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: allow ignoring minor compat-version checkDavid Bauer2022-06-182-0/+5
| | | | | | | | | | | | Downstream projects might re-generate device-specific configuration based on OpenWrt's defaults on each upgrade, thus being unaffected by forward- as well as backwards-breaking configuration. Add a new sysupgrade parameter, which allows sysupgrades between minor compat-versions. Upgrades will still fail upon mismatching major compat versions. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: TP-Link EAP225 v3: use pre-calibration nvmem-cellSander Vanheule2022-06-181-3/+3
| | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Rename the nvmem cell node and label to match the updated cell name. Fixes: eca0d7301198 ("ath79: TP-Link EAP225 v3: convert ath10k to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Wall v2: use pre-calibration nvmem-cellSander Vanheule2022-06-181-3/+3
| | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Rename the nvmem cell node and label to match the updated cell name. Fixes: 48625a04453b ("ath79: TP-Link EAP225-Wall v1: convert radios to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Outdoor v1: use pre-calibration nvmem-cellNick Hainke2022-06-181-3/+3
| | | | | | | | | | | | | | | | | | | | | | Fixes errors in the form of: ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci, vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device =0000 from ath10k/QCA9888/hw2.0/board-2.bin ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0 ath10k_pci 0000:00:00.0: failed to fetch board file: -12 ath10k_pci 0000:00:00.0: could not probe fw (-12) As described already in 2d3321619b2b ("ath79: TP-Link EAP245 v3: use pre-calibration nvmem-cell"): Ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Further rename the nvmem cell node and label to match the updated cell name. Fixes: 23b904074500 ("ath79: TP-Link EAP225-Outdoor v1: convert ath10k to nvmem-cells") Suggested-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: UniFi 6 LR: disable RTCDaniel Golle2022-06-181-0/+6
| | | | | | | | There is not RTC battery connected to the SoC of the UniFi 6 LR board. Disable the RTC to prevent the system coming up with time set to 2000-01-01 00:00:00 after each reboot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: D-Link DAP-2xxx (QCA953x): convert ath9k caldata to nvmemSander Vanheule2022-06-181-2/+11
| | | | | | | | | | Convert the calibration data reference for the ath9k radio to an nvmem-cell, replacing the downstream mtd-cal-data property. Since the 'art' label is no longer used, it can be dropped. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2xxx (QCA953x): move art partition to DTSISander Vanheule2022-06-183-12/+6
| | | | | | | | | The art partition containing the radio calibration data is in the same location for all supported devices. Move the definition to the base file so the reference from the wmac node can reference the same file. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-3662 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-9/+16
| | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2695 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-3/+16
| | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2660 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-2/+15
| | | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Tested-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2680 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-7/+20
| | | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the pre-calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Tested-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2xxx (QCA955x): convert ath9k caldata to nvmemSander Vanheule2022-06-181-1/+10
| | | | | | | | Convert the calibration data reference for the ath9k radio to an nvmem-cell, replacing the downstream mtd-cal-data property. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2xxx (QCA955x): move art partition to DTSISander Vanheule2022-06-185-24/+6
| | | | | | | | | The art partition containing the radio calibration data is in the same location for all supported devices. Move the definition to the base file so the reference from the wmac node can refer to the same file. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* Revert "mac80211: add airtime fairness rework/fixes"Felix Fietkau2022-06-183-986/+2
| | | | | | | This reverts commit 96012227e578a0d8dcfa86823db97345e98e2c8f. Needs some more work until it is ready Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "mac80211: sync airtime fairness fixes with updated upstream submission"Felix Fietkau2022-06-186-239/+90
| | | | | | | This reverts commit 958785508cc802de75698607670f9a236883d24d. Needs some more work until it is ready Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport upstream mtk_eth_soc patchesFelix Fietkau2022-06-1828-13/+3272
| | | | | | Includes MT7986 ethernet support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: move mtk flow offload patches to backport-5.15Felix Fietkau2022-06-1812-6/+6
| | | | | | They were accepted upstream Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: TP-Link EAP245 v3: use pre-calibration nvmem-cellSander Vanheule2022-06-181-1/+1
| | | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Update the nvmem-cell name to make the 5GHz radio work again. Fixes: d4b3b2394233 ("ath79: TP-Link EAP245 v3: convert radios to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: add support for power LED on Netgear GS308Tv1Andreas Böhler2022-06-181-0/+27
| | | | | | | | | | The Netgear GS308Tv1 is already supported by OpenWrt, but is missing LED support. After OpenWrt installation, all LEDs are off which makes the installation quite confusing. This enables support for the green/amber power LED to give feedback about the current status. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* firewall4: bump to git HEADStijn Tintel2022-06-171-3/+3
| | | | | | | | | | | | | | | | | | 11f5c7b fw4.uc: fix zone helper assignment b9d35ff fw4.uc: don't skip zone for unavailable helper e35e26b tests: add test for zone helpers a063317 ruleset: fix conntrack helpers e1cb763 ruleset: reuse zone-jump.uc template for notrack and helper chain jumps 11410b8 ruleset: reorder declarations & output tweaks 880dd31 fw4: fix skipping invalid IPv6 ipset entries 5994466 fw4: simplify `is_loopback_dev()` 53886e5 fw4: fix crash in parse_cthelper() if no helpers are present 11256ff fw4: add support for configurable includes 3b5a033 tests: add test coverage for firewall includes d79911c fw4: support sets with timeout capability but without default expiry 15c3831 fw4: add support for `option log` in rule and redirect sections Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm53xx: copy bgmac revert (performance fix) to 5.15Rafał Miłecki2022-06-171-0/+33
| | | | | Ref: 230c9da963aa ("bcm53xx: revert bgmac back to the old limited max frame size") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: move ethernet phy node for TP-Link EAP devicesSander Vanheule2022-06-165-7/+48
| | | | | | | | Move the ethernet phy definition from the eap2x5-1port include to the device-specific DTS files. This is to prepare for new devices that have a different ethernet phy, at another MDIO address. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Wall v1: convert radios to nvmem-cellsSander Vanheule2022-06-162-9/+24
| | | | | | | | | | | | | Replace the mtd-cal-data phandle by an nvmem-cell reference to the art partition for the 2.4GHz ath9k radio. Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP245 v3: convert radios to nvmem-cellsSander Vanheule2022-06-162-8/+25
| | | | | | | | | | | | | Replace the mtd-cal-data phandle by an nvmem-cell reference from the art partition for the 2.4GHz ath9k radio. Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using an nvmem-cell. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225 v3: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-1/+18
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Outdoor v1: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-1/+18
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225 v1: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-7/+24
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP245 v1: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-1/+18
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: convert 1-port TP-Link EAP ath9k to nvmem-cellsSander Vanheule2022-06-161-3/+10
| | | | | | | | | | | Replace the mtd-cal-data phandle with an nvmem-cell reference for the 2.4GHz ath9k radio. This affects the following devices: - TP-Link EAP225 v1 - TP-Link EAP225 v3 - TP-Link EAP225-Outdoor v1 - TP-Link EAP245 v1 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* uboot-mediatek: update UniFi 6 LR board nameDaniel Golle2022-06-161-1/+1
| | | | | | | Select matching U-Boot for both v1 and v2 variants. Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: add owe_transition_ifnameDavid Bauer2022-06-161-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the owe_transition_ifname config option to wifi-ifaces. This allows to configure OWE transition VAPs without adding SSID / BSSID to the uci conifg but instead autodiscovering these parameters from other networks on the same PHY. The following configuration creates a OWE transition mode network constellation. config wifi-iface 'open0' option device 'radio0' option ifname 'open0' option network 'lan' option mode 'ap' option ssid 'FreeNet' option encryption 'none' option owe_transition_ifname 'owe0' config wifi-iface 'owe0' option device 'radio0' option ifname 'owe0' option network 'lan' option mode 'ap' option ssid 'owe_tm.FreeNet' option encryption 'owe' option hidden '1' option owe_transition_ifname 'open0' Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: sync airtime fairness fixes with updated upstream submissionFelix Fietkau2022-06-156-90/+239
| | | | | | | | - fix ath10k latency issues - reject too large weight values - code cleanup Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: drop phy-mask propertySander Vanheule2022-06-1571-128/+0
| | | | | | | The phy-mask property is no longer supported by the ag71xx-mdio driver, so let's drop it. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: ag71xx-mdio: remove phy-mask propertySander Vanheule2022-06-151-4/+0
| | | | | | | | | | | | | The phy-mask property is read by the ag71xx-mdio driver to set the mii_bus's phy_mask field. On OF platforms, the devicetree is expected to provide all present ethernet phy-s however, so the phy_mask field is later set to all-ones. Having a devicetree override is of no use then, so let's drop it. Cc: David Bauer <mail@david-bauer.net> Cc: John Crispin <john@phrozen.org> Signed-off-by: Sander Vanheule <sander@svanheule.net> Acked-by: David Bauer <mail@david-bauer.net>
* bcm53xx: revert bgmac back to the old limited max frame sizeRafał Miłecki2022-06-151-0/+33
| | | | | | | | | | | Bumping max frame size has significantly affected network performance. It was done by upstream commit that first appeared in the 5.7 release. This change bumps NAT masquarade speed from 196 Mb/s to 383 Mb/s for the BCM4708 SoC. Ref: f55f1dbaad33 ("bcm53xx: switch to the kernel 5.10") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* swconfig: parse "switch_vlan" before "switch_port"Rafał Miłecki2022-06-151-26/+33
| | | | | | | | | | | | | | | Before this change UCI sections of both types were parsed in order as specified in UCI. That didn't work well with all drivers (e.g. b53). It seems that VLAN setup can reset / overwrite previously set ports parameters. It resulted in "switch_port" options defined above "switch_vlan"s being silently ignored. Ideally swconfig & all drivers should be improved to handle that properly but it'd be a waste of time at this point as DSA replaces swconfig. Use this minor parsing change as a quick fix. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* qoriq: use FIT uImage for Firebox M300 kernelStijn Tintel2022-06-141-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This requires U-Boot environment changes: setenv OpenWrt_kernel watchguard_firebox-m300-fit-uImage.itb setenv loadaddr 0x20000000 setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; mmc dev 0; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr' Trying to sysupgrade an image containing this change on an M300 already running OpenWrt will fail with the following error: Tue Jun 14 12:06:21 EEST 2022 upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n). Tue Jun 14 12:06:21 EEST 2022 upgrade: Kernel switched to FIT uImage. Update U-Boot environment. Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from bootdisk... Tue Jun 14 12:06:21 EEST 2022 upgrade: Extract boot sector from the image Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from image... Image check failed. This is to prevent rendering your device unbootable. Make the U-Boot environment changes as instruced above, and then flash the image using sysupgrade -F. The config can be kept, there is no need to use -n. After the new image booted successfully, you can increase the compat_version: uci set system.@system[0].compat_version='1.1' uci commit Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qoriq: use KERNEL_SUFFIX in Build/sdcard-imgStijn Tintel2022-06-141-1/+1
| | | | | | | | | Use the KERNEL_SUFFIX variable in Build/sdcard-img, rather than using hardcoded "-kernel.bin", to allow overriding KERNEL_SUFFIX for a device. Fixes: 080a769b4da8 ("qoriq: new target") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* tools/ninja: update to 1.11.0Rosen Penev2022-06-132-1070/+3081
| | | | | | Updated patchset to latest. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-06-136-2/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 11:31:11 +0000