aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* tools/ccache: update to 4.7.4Linhui Liu2022-12-172-3/+3
| | | | | | | | Release Notes: https://ccache.dev/releasenotes.html#_ccache_4_7_3 https://ccache.dev/releasenotes.html#_ccache_4_7_4 Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* mediatek: redmi-ax6000: drop cs-gpiosChuanhong Guo2022-12-171-1/+0
| | | | | | | | 'cs-gpios = <0>, <0>' is a hack in ath79 to override the incorrectly specified maximum number of chipselects available in spi-ath79.c. It's not needed here and must have been copied here by mistake. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000Chen Minqiang2022-12-178-285/+389
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In this implementation, the flash partition layout is adjusted to avoid modifying the uboot environment of mtdparts. This ensures that the 30M ubi_kernel partition remains aligned with the stock ubi partition, and the kernel volume is placed in it. This allows the stock uboot to boot from it without changing the mtdparts, which is useful for reverting back to the stock firmware using Xiaomi Firmware Tools. In actual testing, modifying mtdparts has been found to break Xiaomi Firmware Tools. 1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation. 2. The NAND flash layout is changed to allow for reverting back to the stock firmware. 3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade to ensure a clean installation of OpenWRT. 4. Setup the uboot env to ensure that the system always boot, which can be helpful for users who may forget to do this before sysupgrade in the initramfs. New flash instructions: 1. Gain ssh access. Please refer to: https://openwrt.org/toh/xiaomi/redmi_ax6000#installation) 2. Check which system current u-boot is loading from: COMMAND: `cat /proc/cmdline` sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1` if firmware=1, current system is ubi1 if firmware=0, current system is ubi0 3. Setup nvram and write the firmware: If the current system is ubi1, please set it up so that the next time it will boot from ubi, and write the firmware to ubi: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi ``` If the current system is ubi, please set it up so that the next time it will boot from ubi1, and write the firmware to ubi1: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi ``` 4. After rebooting, the system should now boot into the openwrt initramfs. Flash the squashfs-sysupgrade.bin via using ssh or luci. ``` sysupgrade -n /tmp/squashfs-sysupgrade.bin ``` Done. For existing users of the Redmi AX6000 running OpenWrt, here are the steps to switch to this new layout: 1. Flash initramfs-factory.ubi ``` mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi ``` 2. After rebooting, the system will boot into the new openwrt-initramfs. Log in and perform a sysupgrade to complete the process. ``` sysupgrade -n /tmp/squashfs-sysupgrade.bin ``` Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* base-files: sysupgrade-tar: allow separated kernel/rootfs ubiChuanhong Guo2022-12-171-14/+27
| | | | | | | | | | There are some devices putting kernel and rootfs on separated ubi volumes. To make OpenWrt compatible with their bootloader, we need to put kernel and rootfs into separated ubi volumes. Add support for CI_KERN_UBIPART and CI_ROOT_UBIPART for this situation. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* base-files: split ubi attaching out of nand_upgrade_prepare_ubiChuanhong Guo2022-12-171-27/+38
| | | | | | | split ubi reformat/attach into nand_attach_ubi in preparation for reusing this code in other functions. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* generic: add support for EON EN25QX128A spi nor flashChristian Marangi2022-12-162-0/+42
| | | | | | | | | Add support for EON EN25QX128A spi nor flash with no flags as it does support SFDP parsing. Fixes: #9442 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
* CI: introduce target toolchain testChristian Marangi2022-12-161-0/+64
| | | | | | Add test to build test toolchain for each target. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* CI: build: make kernel build configurableChristian Marangi2022-12-163-0/+6
| | | | | | Make kernel build configurable to permit to introduce toolchain testing. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* CI: improve build naming for shared workflowChristian Marangi2022-12-162-2/+3
| | | | | | | Impove build naming for build shared workflow to better understand what is being test. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mediatek: add LED support for Xiaomi Redmi AX6000Furong Xu2022-12-163-0/+55
| | | | | | | add DT nodes and default package for the LEDs on Redmi AX6000 Signed-off-by: Furong Xu <xfr@outlook.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: enable sel_clk for spi-mt65xxFurong Xu2022-12-161-0/+29
| | | | | | | | | Without explicitly enabling sel_clk, clk_disable_unused() will disable it when boot is done, causing CPU hang on SPI1 register access on MT7986. Explicitly enable sel_clk to make SPI1 functional. Signed-off-by: Furong Xu <xfr@outlook.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: add driver package for WS2812B LEDsChuanhong Guo2022-12-163-0/+268
| | | | | | | Two WS2812B (NeoPixel) clones are used in Xiaomi Redmi AX6000 as indicator lights. Add a driver for controlling it using SPI MOSI. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mac80211: fix a regression in processing management frames for AP VLAN ↵Felix Fietkau2022-12-161-21/+22
| | | | | | | | interfaces Fixes re-assoc of WDS stations Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: enable coredumpsFelix Fietkau2022-12-161-0/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: always set a default for the nas identifierFelix Fietkau2022-12-161-2/+3
| | | | | | | It is used for both 802.11r and WPA enterprise. Setting it when not needed is harmless Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: work around a race condition on detecting a phy while bringing it upFelix Fietkau2022-12-161-0/+4
| | | | | | | | When reloading modules and running wifi, a phy can sometimes be renamed while in the middle of a hotplug call that tries to detect new phys This can lead to bogus wifi-device sections being created Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix uninitialized variable in rx->link/link_sta initialization fixFelix Fietkau2022-12-161-23/+15
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add support for automatically setting RADIUS own-ip dynamicallyFelix Fietkau2022-12-162-2/+118
| | | | | | Some servers use the NAS-IP-Address attribute as a destination address Signed-off-by: Felix Fietkau <nbd@nbd.name>
* rpcd: update to latest Git HEADJo-Philipp Wich2022-12-161-5/+7
| | | | | | | | | 7de4820 iwinfo: add "hwmodes_text" to the info output b3f530b iwinfo: clean up rpc_iwinfo_call_hw_ht_mode() c46ad61 iwinfo: reuse infos provided by libiwinfo 6c5e900 iwinfo: constify string map arg for rpc_iwinfo_call_int() Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* iwinfo: update to latest Git HEADJo-Philipp Wich2022-12-161-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 8d15809 cli: print current HT mode 8f86dd6 cli: use IWINFO_HTMODE_COUNT f36b72b cli: use IWINFO_KMGMT_NAMES 91be7e0 cli: use IWINFO_CIPHER_NAMES 49b6ec9 cli: fix printing the scan channel width b1c8873 cli: fix marking the active channel 9e14e64 utils: add iwinfo_band2ghz() and iwinfo_ghz2band() helpers e084781 utils: add helper functions to get names by values d09a77a utils: add iwinfo_htmode_is_{ht|vht|he} helpers 8752977 utils: add and use iwinfo_format_hwmodes() 02f433e lib: add IWINFO_80211_COUNT and IWINFO_80211_NAMES 1d30df1 lib: add IWINFO_BAND_COUNT and IWINFO_BAND_NAMES aefd0ef lib: use common IWINFO_CIPHER_NAMES strings a5b30de lib: add IWINFO_OPMODE_COUNT and use it for IWINFO_OPMODE_NAMES 9f29e79 lib: constify and fixup the string array definitions fddc015 nl80211: mark frequencies where HE operation in not allowed 6d50a7c nl80211: add support for HE htmodes 4ba5713 nl80211: properly get available bands for the hwmode 91b2ada nl80211: update the kernel header nl80211.h 3f619a5 nl80211: fix frequency/channel conversion for the 6G band a77d915 nl80211: don't guess if a name is an ifname c27ce71 devices: add usb device MediaTek MT7921AU 14f864e nl80211: add ability to describe USB devices a5a75fd nl80211: remove ancient wpa_supplicant ctrl socket path dd4e1ff nl80211: fix wpa supplicant ctrl socket permissions d638163 fix -Wdangling-else warnings 4aa6c5a fix -Wreturn-type warning 3112726 fix -Wpointer-sign warning ebd5f84 fix -Wmaybe-uninitialized warning 5469898 fix -Wunused-variable warnings 462b679 fix -Wduplicate-decl-specifier warnings ccaabb4 fix -Wformat-truncation warnings 50380db enable useful compiler warnings via -Wall Fixes: https://github.com/openwrt/openwrt/issues/10158 Fixes: https://github.com/openwrt/openwrt/issues/10687 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* realtek: add Linux Kernel 5.15 as testing versionINAGAKI Hiroshi2022-12-151-0/+1
| | | | | | | | | | | | | | | | Add Linux Kernel 5.15 support for testing. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [APRESIA ApresiaLightGS120GT-SS, Panasonic Switch-M24eG PN28240K, Switch-M48eG PN28480K] Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> TP-Link TL-SG2008P Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> [D-Link DGS-1210-20, DGS-1210-52, Zyxel XGS1010-12] Tested-by: Markus Stockhausen <markus.stockhausen@gmx.de> [Zyxel XGS1250-12] Tested-by: Lucian Cristian <lucian.cristian@gmail.com> # Zyxel [HPE 1920-8G, 1920-48G] Tested-by: Jan Hoffmann <jan@3e8.eu>
* realtek: enable needs_standalone_vlan_filtering on DSA driver in 5.15INAGAKI Hiroshi2022-12-151-0/+1
| | | | | | | To configure VLAN 0, enable needs_standalone_vlan_filtering option of dsa_switch struct. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: update dsa.c of DSA driver for 5.15INAGAKI Hiroshi2022-12-151-101/+88
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - rtl83xx_vlan_filtering() "struct switchdev_trans *trans" parameter was removed[1] and "struct netlink_ext_ack *extack" was added[2]. [1]: https://www.spinics.net/lists/netdev/msg712250.html [2]: https://www.spinics.net/lists/netdev/msg722496.html - rtl83xx_vlan_add/del() vlan->vid_begin and vlan->vid_end were removed and vlan->vid was added[3]. [3]: https://www.spinics.net/lists/netdev/msg712248.html - rtl83xx_vlan_prepare() "port_vlan_prepare" member was removed from "dsa_switch_ops" struct in dsa.h[4] and vlan_prepare function should be called from vlan_add function. Also, change return type of vlan_add function to int. [4]: https://www.spinics.net/lists/netdev/msg712252.html - rtl83xx_port_mdb_add() "port_mdb_prepare" member in "dsa_switch_ops" struct was removed and preparation need to be done in the function of "port_mdb_add" member instead. And also, int type need to be returned on "port_mdb_add" member[5]. [5]: https://www.spinics.net/lists/netdev/msg712251.html - rtl83xx_port_pre_bridge_flags(), rtl83xx_port_bridge_flags() The current "port_pre_bridge_flags" member and "port_bridge_flags" member in "dsa_switch_ops" in dsa.h has flags of "struct switchdev_brport_flags" type instead[6], so adjust to it. And, the changed features are passed by flags.mask[7] in rtl83xx_port_bridge_flags(), so check it before calling function to enable/disable fieature. [6]: https://lore.kernel.org/lkml/20210212151600.3357121-7-olteanv@gmail.com/ [7]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e18f4c18ab5b0dd47caaf8377c2e36d66f632a8c Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [shorten final return statement of rtl83xx_port_mdb_add()] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: update platform support for 5.15INAGAKI Hiroshi2022-12-152-6/+2
| | | | | | | | | | - fw_passed_dtb and others were replaced to get_fdt() function[1] - __appended_dtb defined by asm/bootinfo.h[2] [1]: https://www.spinics.net/lists/linux-mips/msg03332.html [2]: https://www.spinics.net/lists/linux-mips/msg03332.html Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: refresh config-5.15 in all subtargetsINAGAKI Hiroshi2022-12-154-92/+123
| | | | | | Refresh config-5.15 in all subtargets by kernel_menuconfig. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: refresh patches in 5.15INAGAKI Hiroshi2022-12-1532-126/+121
| | | | | | Adjust patches for kernel 5.15. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: drop patches of upstreamed fix and changes from 5.15INAGAKI Hiroshi2022-12-154-1113/+0
| | | | | | | | | | - 007-5.16-gpio-realtek...: upstreamed on 5.16 and backported to 5.15.3 - 708-brflood-spi.patch : upstreamed - 709-lag-offloading.patch: upstreamed - 713-v5.12-net-dsa-... : upstreamed and some implementations are replaced Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: drop patches of upstreamed drivers from 5.15INAGAKI Hiroshi2022-12-156-1091/+0
| | | | | | | | | | | The following drivers were upstreamed and available on 5.15, so drop from OpenWrt tree. - realtek-otto-gpio (5.13) - realtek-rtl-spi (5.12) - realtek-rtl-intc (5.12) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: copy dts/files/patches/configs for 5.15INAGAKI Hiroshi2022-12-15139-0/+39485
| | | | | | | | Copy dts/files/patches/configs from 5.10 to 5.15. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [refresh with updated DGS-1210 dts files] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* firmware-utils: fix archive checksumSander Vanheule2022-12-151-1/+1
| | | | | | | | | PKG_SOURCE_DATE was modified after updating PKG_MIRROR_HASH, causing the latter to change. This results in a warning during builds and rejected downloads. Fixes: 232879a7b7f8 ("firmware-utils: bump to git HEAD") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: fix dtc warnings in ruckus zf7372Christian Lamparter2022-12-151-0/+4
| | | | | | | |:69.4-14: Warning (reg_format): beamforming-2g-gpio@0:reg: property has invalid length (4 bytes) |:85.4-14: Warning (reg_format): beamforming-5g-gpio@0:reg: property has invalid length (4 bytes) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: fix dtc warnings in eap1750hChristian Lamparter2022-12-151-19/+19
| | | | | | | | | | | | |109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes) |113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes) |117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes) also integrate the art-nodes nodes back into the partition-subnode and change the calibration labels to match what everyone else is doing. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: fix dtc warnings in eap1200hChristian Lamparter2022-12-151-19/+19
| | | | | | | | | | | | |109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes) |113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes) |117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes) also integrate the art-nodes nodes back into the partition-subnode and change the calibration labels to match what everyone else is doing. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: replace reference to legacy qca,disable-2ghz in WatchGuard AP100Nick Hainke2022-12-151-1/+1
| | | | | | | | | Commit 4c8dd973ef8e ("ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit") removed "qca,disable-5ghz" and "qca,disable-2ghz". Signed-off-by: Nick Hainke <vincent@systemli.org> (converted patch to remove the ieee80211-freq-limit property instead) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: switch to upstream ieee80211-freq-limit for Araknis AN-300-AP-I-NNick Hainke2022-12-151-2/+2
| | | | | | | | Commit 4c8dd973ef8e ("ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit") removed "qca,disable-5ghz" and "qca,disable-2ghz". Switch to upstream ieee80211-freq-limit. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: convert Winchannel WB2000 WiFis to nvmem-cellsNick Hainke2022-12-152-20/+26
| | | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (removed mtd-cal-data property, merged art + addr nodes back into partition) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert Ubiquiti UniFi AP Pro WiFis to nvmem-cellsNick Hainke2022-12-152-14/+21
| | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (merged art node back into partition-node) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert OCEDO Raccoon WiFis to nvmem-cellsNick Hainke2022-12-152-27/+30
| | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (merged art into partition node, removed stale uboot label) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: Mercury MW4530R v1 already uses nvmem-cellsNick Hainke2022-12-151-1/+0
| | | | | | | | Remove the caldata extraction in userspace. The board already uses nvmem-cells since commit e354b01baf88 ("ath79: calibrate all ar9344 tl-WDRxxxx with nvmem") Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: convert boards based on senao_ap-dual.dtsi WiFis to nvmem-cellsNick Hainke2022-12-156-21/+51
| | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: convert Atheros DB120 WiFis to nvmem-cellsNick Hainke2022-12-152-18/+25
| | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (merged art-node back into partition-node) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert Araknis AN-300-AP-I-N WiFis to nvmem-cellsNick Hainke2022-12-152-8/+12
| | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org>
* bcm27xx: bcm2711: add kmod-r8169Johannes Heimansberg2022-12-151-1/+2
| | | | | | | | | | | | | | | | | | Some carrier boards [1][2] for the Raspberry Pi CM4 that are specifically designed to be used as routers come with secondary NICs using a Realtek RTL8111 Gigabit Ethernet chip. When using such a board as a router with OpenWrt, it is very helpful when both NICs are working by default. Since the Raspberry Pi 4 and the CM4 have plenty of disk space, it should cause no harm to include the kmod-r8169. [1] https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767 [2] https://www.waveshare.com/wiki/CM4-DUAL-ETH-MINI Signed-off-by: Johannes Heimansberg <git@jhe.dedyn.io> (r8169 should pull in the necessary dependencies.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: Patch to support BCMA rev 11Linus Walleij2022-12-152-0/+56
| | | | | | | A backported patch to the BCMA driver necessary to support the DWL-8610AP and DIR-890L. Patch will be in upstream v6.2. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* firmware-utils: bump to git HEADSander Vanheule2022-12-151-3/+3
| | | | | | | | Adds support for building TP-Link CPE605v1 factory images bd856eff4850 tplink-safeloader: add TP-Link CPE605 v1 Support Signed-off-by: Sander Vanheule <sander@svanheule.net>
* kernel: bump 5.10 to 5.10.159John Audia2022-12-145-37/+7
| | | | | | | | | | | | | | | Removed upstreamed: backport-5.10/888-v6.1-ca8210-Fix-crash-by-zero-initializing-data.patch[1] All patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.159&id=0a8e66e375736ea12c11f0ef238ba2a8efec460b Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.83John Audia2022-12-1419-67/+37
| | | | | | | | | | | | | | | Removed upstreamed: backport-5.15/883-v6.1-ca8210-Fix-crash-by-zero-initializing-data.patch[1] All patches automatically rebased 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.83&id=246bcd05ba6cc43b34ac0bb4bac3ea94a4efa07c Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* tools/dosfstools: fix PKG_SOURCEStijn Tintel2022-12-141-2/+2
| | | | | | | | Both mirrors provided in the Makefile only serve gzipped tarballs. Fixes: #10871 Fixes: 9edfe7dd13d9 ("source: Switch to xz for packages and tools where possible") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add missing symbol to 5.10 configStijn Tintel2022-12-141-0/+1
| | | | | | | | | | Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol. This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing those builds to fail due to a missing symbol. Add the symbol to fix this. Fixes: 6801c460b6a7 ("kernel: bump 5.10 to 5.10.158") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add missing symbol to 5.15 configStijn Tintel2022-12-141-0/+1
| | | | | | | | | | Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol. This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing those builds to fail due to a missing symbol. Add the symbol to fix this. Fixes: 68426e54eda4 ("kernel: bump 5.15 to 5.15.82") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-01 05:47:05 +0000