aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ipq807x: Enable CPU frequency scaling statsHannu Nyman2023-01-311-1/+1
| | | | | | | Enable the CPU frequency scaling statistics in kernel config. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> Reviewed-by: Robert Marko <robimarko@gmail.com>
* realtek: use generic earlycon setup on 5.15INAGAKI Hiroshi2023-01-309-15/+32
| | | | | | | | | | Use generic earlycon on Linux Kernel instead of initialization in platform setup. And also, drop bootargs with console= parameter from I-O DATA BSH-G24MB. It uses 115200bps as baud-rate, the same as default in rtl838x.dtsi. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* mxs: switch default kernel to 5.15Zoltan HERPAI2023-01-302-245/+1
| | | | | | | The testing kernel has been available since Mar/2022, let's switch to it by default. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath25: mark as source-onlyRobert Marko2023-01-301-1/+1
| | | | | | | | | | | | | | | ath25 seems to be a target with low number of users according to download statistics, most of which are for older releases anyway. Users that we managed to find are currently building images downstream as due to low amount of RAM (32MB) default config will not work. Target also suffers from inability for the 5.15 kernel bump to be tested which is a requirment for the next release. So, for those reasons, lets mark it as source-only so that Buildbots dont use the resources for building the images for this target anymore. Signed-off-by: Robert Marko <robimarko@gmail.com>
* zynq: remove kconfig for 5.10Chuanhong Guo2023-01-301-546/+0
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* zynq: switch default kernel to 5.15Nick Hainke2023-01-301-2/+1
| | | | | | | The default kernel should be switched to 5.15 in order to enable testing by a broader audience. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ubus: fix wrong package mirror hashPetr Štetiar2023-01-301-1/+1
| | | | | | | | | | I've somehow managed to commit wrong package mirror hash in commit 36076b5a4092 ("ubus: update to version 2022-06-15"), so lets fix it by using a proper one. Fixes: 36076b5a4092 ("ubus: update to version 2022-06-15") Reported-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* realtek: remove KERNEL_PATCHVER overridesSander Vanheule2023-01-294-8/+0
| | | | | | | | | | On the realtek target, the subtarget makefiles include a KERNEL_PATCHVER setting, shadowing KERNEL_PATCHVER from target/linux/realtek/Makefile. This makes the realtek target an exception in this regard, and makes switching kernel version a bit bothersome. Remove the overrides so all subtargets use the same kernel version. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* kernel: make it possible for packages to select page pool supportFelix Fietkau2023-01-293-0/+29
| | | | | | Will be used by the next mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bridger: update to the latest versionFelix Fietkau2023-01-291-3/+3
| | | | | | 8be8bb9df789 nl: fix accessing hairpin mode and isolated from the right attribute set Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add fix for a page pool related crash on GROFelix Fietkau2023-01-292-0/+70
| | | | | | Needed for upcoming mt76 page pool support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport page pool fragment support from v5.15Felix Fietkau2023-01-294-4/+802
| | | | | | Required for an upcoming mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: backport napi_build_skb for 5.10Felix Fietkau2023-01-291-0/+11
| | | | | | It is needed for an upcoming mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ucode: update to the latest versionFelix Fietkau2023-01-291-4/+4
| | | | | | | | | | | 1c8df08824ef style: add .editorconfig file ec167d39b803 nl80211: refactor command bitmask handling 6704ec0d5b29 nl80211: add support for registering an uloop based listener 48a6eac1da15 fs: implement `fs.pipe()` f1be0d725735 types: fix array unshift operations and add test coverage 941d14837faf Merge pull request #138 from nbd168/nl80211 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-envtools: filogic: bpi-r3: fix env selectionDaniel Golle2023-01-291-4/+7
| | | | | | | | Selecting the environment when booting from SD card has been broken by a previous commit. Fix it. Fixes: f46355b4d7 ("uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: mt7622: bpi-r64: fix env selectionDaniel Golle2023-01-291-3/+6
| | | | | | | | Selecting the environment when booting from SD card has been broken by a previous commit. Fix it. Fixes: 84b5b0f88c ("uboot-envtools: mediatek/mt7622: don't rely on mapped rootfs") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: fix wrong return code in platform_check_image()Chen Minqiang2023-01-292-1/+2
| | | | | | Ensure that the platform_check_image() function returns an error code. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* base-files: fix nand_do_platform_check failChen Minqiang2023-01-291-1/+5
| | | | | | | | | | | | This change ensures compatibility with both types of sysupgrade-tar files. 1. For some boards like xiaomi,redmi-router-ax6s, sysupgrade-tar is pack in directory `vendor,name/` 2. For some boards like xiaomi,mi-router-3g, sysupgrade-tar is pack in directory `vendor_name/` Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ucode: move to the lang submenuAndre Heider2023-01-281-5/+9
| | | | | | | Just as lua or the various languages from the package feed. libucode is the exception, so move it to the libs menu instead. Signed-off-by: Andre Heider <a.heider@gmail.com>
* uhttpd: clean up MakefileAndre Heider2023-01-281-20/+1
| | | | | | | | | | | | uhttpd's cmake options all default to ON. Either we set all of them or none if the defaults need to be changed. Let's go with the latter. Because support for all modules is always compiled in, remove two unused and useless config toggles. uhttpd detects and uses libcrypt itself, no need to add it here again. Signed-off-by: Andre Heider <a.heider@gmail.com>
* px5g-mbedtls: Use getrandom()Hauke Mehrtens2023-01-281-4/+8
| | | | | | | | | | | | | | | | Instead of accessing /dev/urandom use the getrandom syscall. This way we do not have to keep the file open all the time. This also fixes a compile error with glibc: -------- px5g-mbedtls.c: In function '_urandom': px5g-mbedtls.c:48:9: error: ignoring return value of 'read' declared with attribute 'warn_unused_result' [-Werror=unused-result] 48 | read(urandom_fd, out, len); | ^~~~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors -------- Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2Dmitry Sokolov2023-01-286-132/+241
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device is the same as Xiaomi Mi Router 4A Gigabit, except of: - 5G WiFi is MT7663 - addresses of leds, wifi and eth ports are slightly changed Specs: SoC: MT7621 CPU: 2 x 880 MHz ROM: 16 MB RAM: 128 MB WLAN: MT7603, MT7663 MAC addresses: WAN **** factory 0xe006 (label) LAN *:f7 factory 0xe000 2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4) 5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4) Installation: Factory firmware is based on a custom OpenWrt 17.x. Installation is the same as for Xiaomi Mi Router 4A Gigabit. Probably the easiest way to install is to use the script from this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155 In a more advanced case, you can do everything yourself: - gain access to the device through one of the exploits described in the link above - upload sysupgrade image to /tmp - overwrite stock firmware: # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1 Recovery: Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit. Possible options can be found here: https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition One of the ways is to use another router with OpenWrt: - connect both routers by their LAN ports - download stock firmware from [1] - place it inside /tmp/test.bin on the main router - configure PXE/TFTP on the main router - power off 4Av2, hold Reset button, power on - as soon as image download via TFTP starts, Reset can be released - blinking blue wan LED will indicate the end of the flashing process, now router can be rebooted [1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin Signed-off-by: Dmitry Sokolov <e323w@proton.me>
* ramips: improve support for Zyxel Keenetic Extra IIMaxim Anisimov2023-01-283-13/+27
| | | | | | | | | | | - drop unneeded default-state for led_power - concat firmware partitions to extend available free space - increase spi flash frequency to 32 Mhz (value from stock firmware bootlog) - drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support - add compatible for pcie wifi according to kernel documetation - switch to wan mac address with offset 0x28 in rf-eeprom Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: use hex value in zyimage command for Keenetic KN-3010Maxim Anisimov2023-01-281-1/+1
| | | | | | | This is cosmetic change. The hex value is related to the device model and more human friendly. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ath79: add LTE packages for GL-XE300Tom Herbers2023-01-281-1/+2
| | | | | | | | | | | | | | | | | Add LTE packages required for operating the LTE modems shipped with the GL-XE300. Example configuration for an unauthenticated dual-stack APN: network.wwan0=interface network.wwan0.proto='qmi' network.wwan0.device='/dev/cdc-wdm0' network.wwan0.apn='internet' network.wwan0.auth='none' network.wwan0.delay='10' network.wwan0.pdptype='IPV4V6' Signed-off-by: Tom Herbers <mail@tomherbers.de>
* ath79: improve support for Letv LBA-047-CHShiji Yang2023-01-282-37/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Convert wireless calibration data to NVMEM. 2. Enable control green status LED and change default LED behaviors. The three LEDs of LBA-047-CH are in the same position, and the green LED will be completely covered by the other two LEDs. So don's use green LED as WAN indicator to ensure that only one LED is on at a time. LED Factory OpenWrt blue internet fail failsafe && upgrade green internet okay run red boot boot 3. Reduce the SPI clock to 30 MHz because the ath79 target does not support 50 MHz SPI operation well. Keep the fast-read support to ensure the spi-mem feature (b3f9842330) is enabled. 4. Remove unused package "uboot-envtools". 5. Split the factory image into two parts: rootfs and kernel. This change can reduce the factory image size and allow users to upgrade the OpenWrt kernel loader uImage (OKLI) independently. The new installation method: First, rename "squashfs-kernel.bin" to "openwrt-ar71xx-generic-ap147-16M-kernel.bin" and rename "rootfs.bin" to "openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin". Then we can press reset button for about 5 seconds to enter tftp download mode. Finally, set IP address to 192.168.67.100 and upload the above two parts via tftp server. Tested on Letv LBA-047-CH Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: calibrate dlink dir-825 c1 and dir-835 a1 with nvmemEdward Chow2023-01-283-8/+39
| | | | | | | | | | | | | Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. Currently, "mac-address-ascii" cells only works for ethernet and wmac devices, so PCI ath9k device uses the old method to calibrate. Signed-off-by: Edward Chow <equu@openmail.cc>
* kernel: add kmod-lib-842Tony Butler2023-01-282-0/+23
| | | | | | | | | | "842" is a compression scheme and this is the software implementation which is too slow to really use beyond a proof of concept. It can be selected in ZRAM, ZSWAP, or `fs/pstore`, and is here for completeness. In general you need a Power8 or better with 842-in-hardware for it to be fast, but other 842-accelerators are emerging. Signed-off-by: Tony Butler <spudz76@gmail.com>
* ath79: add label-mac-device for GL-XE300Tom Herbers2023-01-281-0/+4
| | | | | | | This adds an label-mac-device alias which refrences the mac which is printed on the Label of the device. Signed-off-by: Tom Herbers <mail@tomherbers.de>
* realtek: dgs-1210-10mp: update sfp phy-handleDaniel Groth2023-01-282-4/+4
| | | | | | | | Adjust the wrong phy-handle definitions for the sfp ports so that they match the correct switch ports. Fixes: 89eb8b50d18d ("realtek: dgs-1210-10mp: add full sfp description") Signed-off-by: Daniel Groth <flygarn12@gmail.com>
* ath79: add support for Senao Engenius EWS660APMichael Pratt2023-01-285-0/+147
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-EWS660AP Engenius EWS660AP is an outdoor wireless access point with 2 gigabit ethernet ports, dual-band wireless, internal antenna plates, and 802.3at PoE+ **Specification:** - QCA9558 SOC 2.4 GHz, 3x3 - QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - AR8033 PHY SGMII GbE with PoE+ OUT - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM - UART at J1 populated, RX grounded - 6 internal antenna plates (5 dbi, omni-directional) - 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset) **MAC addresses:** Base MAC addressed labeled as "MAC" Only one Vendor MAC address in flash eth0 *:d4 MAC art 0x0 eth1 *:d5 --- art 0x0 +1 phy1 *:d6 --- art 0x0 +2 phy0 *:d7 --- art 0x0 +3 **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin **Installation:** 2 ways to flash factory.bin from OEM: Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware Upgrade" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot execute tftpboot and bootm 0x81000000 **Format of OEM firmware image:** The OEM software of EWS660AP is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-ar71xx-generic-ews660ap-uImage-lzma.bin openwrt-ar71xx-generic-ews660ap-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. Newer EnGenius software requires more checks but their script includes a way to skip them, otherwise the tar must include a text file with the version and md5sums in a deprecated format. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Tested-by: Niklas Arnitz <openwrt@arnitz.email> Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add pcie1 wifi device to Senao qca955x AP DTSIMichael Pratt2023-01-288-5/+38
| | | | | | Each individual device DTS now enables either pcie0 or pcie1. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ethtool: update to 6.1Nick Hainke2023-01-284-2/+555
| | | | | | | | | | | | Release notes: https://lore.kernel.org/netdev/20221219225600.r54vejiqapn266cm@lion.mk-sys.cz/T/ Add patches fixing compilation: - 100-uapi-Bring-in-if-h.patch - 101-netlink-Fix-maybe-uninitialized-meters-variable.patch - 102-raw-marvell-c-Fix-build-with-musl-libc.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* relayd: bump to version 2023-01-28Hauke Mehrtens2023-01-281-3/+3
| | | | | | f646ba4 route: Fix compile warning with glibc Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* pistachio: Cleanup kernel configurationHauke Mehrtens2023-01-281-12/+1
| | | | | | | This removes some kernel configuration options which are not needed. This brings the target closer to the OpenWrt standard configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: Refresh kernel patchesHauke Mehrtens2023-01-281-1/+1
| | | | | | | Make the patches apply cleanly again. Fixes: 4db8598e4296 ("realtek: Do not set KERNEL_ENTRY just to avoid NO_EXCEPT_FILL") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uhttpd: update to latest Git HEADHauke Mehrtens2023-01-281-3/+3
| | | | | | | 47561aa mimetypes: add audio/video support for apple airplay 6341357 ucode: respect all arguments passed to send() Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: timer: Fix cosmetic whitespace in commentsOlliver Schinagl2023-01-281-20/+7
| | | | | | Comments are a bit weird in the timer driver, lets fix those. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* realtek: timer: Remove CEVT_RTL9300 completelyOlliver Schinagl2023-01-283-268/+0
| | | | | | | As the timer has been fixed now, we can drop the CEVT_RTL9300 timer all together. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* realtek: timer: Activate for RTL930x devicesOlliver Schinagl2023-01-283-15/+16
| | | | | | | | | Use the new timer driver for the RTL930x devices. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> [remove old clock provider, select MIPS_EXTERNAL_TIMER and refresh kernel config] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: timer: Register enabled scheduler clockSander Vanheule2023-01-282-2/+2
| | | | | | | | | | | | | Before calling sched_clock_register(), the timer used to drive the scheduling clock should already be enabled. Otherwise the kernel log will show strange time jumps during, and the watchdog might not be pinged in a timely fashion, resulting in reboots. [ 0.160281] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 78.104319] clocksource: Switched to clocksource realtek_otto_timer Fixes: 3cc801117118 ("realtek: resurrect timer driver") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* mac80211: use 802.11ax iw modesDavid Bauer2023-01-281-3/+3
| | | | | | | | | | This adds missing HE modes to mac80211_prepare_ht_modes. Previously mesh without wpa_supplicant would be initialized with 802.11g /NO-HT only, as this method did not parse channel bandwidth for HE operation. Signed-off-by: David Bauer <mail@david-bauer.net>
* mxs: fix SD-card image generation for OLinuXino boardsZoltan HERPAI2023-01-271-1/+1
| | | | | | | | | Fixes: mxs: add generic subtarget (64ef920) Adding the generic target caused the TARGET_BOOTFS_PARTSIZE to stay hidden for these boards, crashing the FAT filesystem creation. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* realtek: eth: Fix missing end of comment markerOlliver Schinagl2023-01-271-1/+1
| | | | | | | Because this comment is followed by another comment, nothing luckily breaks, so only a cosmetic change. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* ubus: update to version 2022-06-15Petr Štetiar2023-01-271-3/+3
| | | | | | | | | | | Update which contains just a following fix: * ubusd: add lookup command queuing support Defers and continues a client's lookup command to avoid unnecessary buffering under load. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ci: allow custom kernel and target jobs based on labelsPetr Štetiar2023-01-272-0/+82
| | | | | | | | | | | | | | Current job triggers based on matching of changed paths is quite limited, so lets make it possible to additionally trigger manual CI jobs by adding CI specific pull request build labels: * `ci:target:x86:64` label is going to trigger CI target check jobs for x86/64 (sub)target. * `ci:kernel:x86:64` label is going to trigger CI kernel check jobs for x86/64 (sub)target. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* linux-firmware: update to 20230117Nick Hainke2023-01-261-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: 32d3199 linux-firmware: Update firmware file for Intel Bluetooth AX201 2da8a7a linux-firmware: Update firmware file for Intel Bluetooth AX201 8b5ddf4 linux-firmware: Update firmware file for Intel Bluetooth AX211 4219dac linux-firmware: Update firmware file for Intel Bluetooth AX211 fb34135 linux-firmware: Update firmware file for Intel Bluetooth AX210 becd3fc linux-firmware: Update firmware file for Intel Bluetooth AX200 7101c57 linux-firmware: Update firmware file for Intel Bluetooth AX201 49e87fa linux-firmware: Update firmware file for Intel Bluetooth 9560 86b73ce linux-firmware: Update firmware file for Intel Bluetooth 9260 3723b48 brcm: add configuration files for CyberTan WC121 7f626ef qcom: add firmware files for Adreno A200 fc5a25f rtw89: 8852c: update fw to v0.27.56.10 2ba1bea QCA: Add Bluetooth firmware for QCA2066 a1ad1d5 amdgpu: add VCN4.0.4 firmware from amd-5.4 9e01e17 amdgpu: add SMU13.0.7 firmware from amd-5.4 3a50eb8 amdgpu: add SDMA6.0.2 firmware from amd-5.4 19995fb amdgpu: add PSP13.0.7 firmware from amd-5.4 32e7c93 amdgpu: add GC11.0.2 firmware from amd-5.4 20c8060 amdgpu: add DCN3.2.1 firmware from amd-5.4 5c8e895 amdgpu: update VCN4.0.0 firmware from amd-5.4 66b3435 amdgpu: update SMU13.0.0 firmware from amd-5.4 604df78 amdgpu: update SDMA6.0.0 firmware from amd-5.4 3e9169a amdgpu: update PSP13.0.0 firmware from amd-5.4 bd1b7f7 amdgpu: update GC11.0.0 firmware from amd-5.4 c8ff1f4 iwlwifi: add new FWs from core76-35 release 5630963 iwlwifi: update cc/Qu/QuZ firmwares for core76-35 release 8bbec22 iwlwifi: add new FWs from core75-47 release e20a687 iwlwifi: update 9000-family firmwares to core75-47 504b691 amdgpu: update renoir DMCUB firmware 1ed02d5 amdgpu: Update renoir PSP firmware d0598c3 amdgpu: update copyright date for LICENSE.amdgpu cee86df linux-firmware: update firmware for MT7921 WiFi device e2d1174 linux-firmware: update firmware for MT7922 WiFi device ce7cc73 linux-firmware: update firmware for mediatek bluetooth chip (MT7921) 91f4c6b linux-firmware: update firmware for mediatek bluetooth chip (MT7922) 52e62d6 cxgb4: Update firmware to revision 1.27.1.0 4704e25 qca: Update firmware files for BT chip WCN6750 c9c1958 rtw89: 8852c: update fw to v0.27.56.9 9e91f0c rtw89: 8852c: update fw to v0.27.56.8 Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: add support for D-Link DIR-629 A1Shiji Yang2023-01-264-0/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: QCA9588 CPU 720 MHz AHB 200 MHz Switch: AR8236 RAM: 64 MiB DDR2-600 Flash: 8 MiB WLAN: Wi-Fi4 2.4 GHz 3*3 LAN: LAN ports *4 WAN: WAN port *1 Buttons: reset *1 + wps *1 LEDs: ethernet *5, power, wlan, wps MAC Address: use address source label 70:62:b8:xx:xx:96 lan && wlan lan 70:62:b8:xx:xx:96 mfcdata@0x35 wan 70:62:b8:xx:xx:97 mfcdata@0x6a wlan 70:62:b8:xx:xx:96 mfcdata@0x51 Install via Web UI: Apply factory image in the stock firmware's Web UI. Install via Emergency Room Mode: DIR-629 A1 will enter recovery mode when the system fails to boot or press reset button for about 10 seconds. First, set IP address to 192.168.0.1 and server IP to 192.168.0.10. Then we can open http://192.168.0.1 in the web browser to upload OpenWrt factory image or stock firmware. Some modern browsers may need to turn on compatibility mode. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* firmware: intel-microcode: update to 20221108Linhui Liu2023-01-261-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changelog: * New Microcodes: sig 0x000606c1, pf_mask 0x10, 2022-08-07, rev 0x1000201, size 286720 sig 0x000b0671, pf_mask 0x32, 2022-09-07, rev 0x010e, size 204800 * Updated Microcodes: sig 0x000706e5, pf_mask 0x80, 2022-08-02, rev 0x00b6, size 113664 sig 0x000806c1, pf_mask 0x80, 2022-06-28, rev 0x00a6, size 110592 sig 0x000806d1, pf_mask 0xc2, 2022-06-28, rev 0x0042, size 102400 sig 0x000806ec, pf_mask 0x94, 2022-07-31, rev 0x00f4, size 105472 sig 0x00090661, pf_mask 0x01, 2022-07-15, rev 0x0017, size 20480 sig 0x00090672, pf_mask 0x07, 2022-09-19, rev 0x0026, size 218112 sig 0x00090675, pf_mask 0x07, 2022-09-19, rev 0x0026 sig 0x000b06f2, pf_mask 0x07, 2022-09-19, rev 0x0026 sig 0x000b06f5, pf_mask 0x07, 2022-09-19, rev 0x0026 sig 0x000906a3, pf_mask 0x80, 2022-09-19, rev 0x0424, size 217088 sig 0x000906a4, pf_mask 0x80, 2022-09-19, rev 0x0424 sig 0x000906ed, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 104448 sig 0x000a0652, pf_mask 0x20, 2022-07-31, rev 0x00f4, size 96256 sig 0x000a0653, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 97280 sig 0x000a0655, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 96256 sig 0x000a0660, pf_mask 0x80, 2022-07-31, rev 0x00f4, size 97280 sig 0x000a0661, pf_mask 0x80, 2022-07-31, rev 0x00f4, size 96256 sig 0x000a0671, pf_mask 0x02, 2022-08-02, rev 0x0056, size 103424 We need to update to this version because https://ftp.debian.org/debian/pool/non-free/i/intel-microcode/intel-microcode_3.20220809.1.tar.xz has been removed. Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* tcpdump: update to 4.99.3Nick Hainke2023-01-261-2/+2
| | | | | | | Changes: https://git.tcpdump.org/tcpdump/blob/032e4923e5202ea4d5a6d1cead83ed1927135874:/CHANGES Signed-off-by: Nick Hainke <vincent@systemli.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-28 14:26:11 +0000