aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* config: don't define the same symbol twiceKoen Vandeputte2018-01-171-1/+0
| | | | | | | | | | | | | | | | | In commit fce35bce0f6e ("config: support new symbol intro'd in kernel 4.12") I forgot to remove the initial debug test line. This clearly is wrong as the same symbol is defined conditionally in the line below as it should be. I looked over it as I just checked if the symbol was present now upon testing it. Fixes: fce35bce0f6e ("config: support new symbol intro'd in kernel 4.12") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix format of the 701-MIPS-ath79-add-routerboard-detection patchesGabor Juhos2018-01-172-2/+2
| | | | | | | | | | | | Commit e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff format, the unchanged, contextual lines must be preceded by a space character. Refresh the patches with quilt to fix them. Fixes: e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix format of the 741-MIPS-ath79-add-PCI-for-QCA9556-SoC patchesGabor Juhos2018-01-172-12/+12
| | | | | | | | | | | The patches introduced in commit 20e68f6d395d ("ar71xx: kernel: enable PCI on QCA9556 SoC") have non standard format. In unified diff format, the unchanged, contextual lines must be preceded by a space character. Refresh the patches with quilt to fix them. Fixes: 20e68f6d395d ("ar71xx: kernel: enable PCI on QCA9556 SoC") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: mach-rbspi: simplify reset button registrationGabor Juhos2018-01-171-64/+30
| | | | | | | | | | | | The setup code defines four individual structures for the Reset buttons of the supported boards. The only difference between the definitions is the GPIO number used for the button. Replace the different structures with one generic variant, and add a helper function to simplify the button registration. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* imx6: add support for the intel gbit driver on GW5520Koen Vandeputte2018-01-171-0/+1
| | | | | | | | | | The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the internal i.MX6 FEC. Add support for these. Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mac80211: remove support code for authsaeFelix Fietkau2018-01-171-9/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* authsae: remove packageFelix Fietkau2018-01-173-131/+0
| | | | | | | It is no longer actively maintained and does not work well in many configurations. Fully replaced by wpad-mesh Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq8065: adjust SS USB PHY power settingsPavel Kubelun2018-01-171-0/+11
| | | | | | | | | | | According to QSDK ipq8065 has different SS USB PHY power settings. Adjust it according to QSDK settings. It also corresponds to oem Netgear R7800 tarball for soc ver >= 2. https://github.com/paul-chambers/netgear-r7800/blob/eeac2e10190f6f45e32e4c7012c4babc351898d8/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2494 Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: usb: add phy 1 master reset controlPavel Kubelun2018-01-172-12/+26
| | | | | | | In current state only phy 0 master reset is controlled. Add the phy 1 reset. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: usb: Control USB master resetPavel Kubelun2018-01-172-0/+67
| | | | | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3 Commit message: "During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated." Change-Id: I537dc810f6cb2a46664ee674840145066432b957 Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org> (cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: dwc3: Fix power_on and power_off sequencePavel Kubelun2018-01-171-29/+58
| | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=d316437c9cdb70023a760342678f32e27241725a The commit fixes: - dwc3 phy module unloading - possibly fixes FS#177 when some devices were improperly enumerated as HS while being SS thus stucking the driver during boot. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: Update HSIO recommended usb phy settingsPavel Kubelun2018-01-171-15/+77
| | | | | | | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=cf82fdf4bdd081cd81bb081f7815b915bc8bb851 The comit adjusts USB dwc3 phy default values as per QSDK recomendation and allows to set it through DT. Commit message: "SoC version based values will be recovered from the device node. If device node does not have such values, defaults are applied. Change-Id: Ia77b5b7fe95ce1a433885df1761091bced98d989 Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* Revert "ipq8064: Fix dwc3 module unloading"Pavel Kubelun2018-01-171-11/+3
| | | | | | | | Preparing for proper fixes thus reverting commits: - 8db079a9ff1756059250b801617a20baba214684 "ipq8064: Fix dwc3 module unloading" - c75f059b0c4d09dd0da60e14c4933a9f645266d1 "ipq8064: Fix dwc3 module unloading" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: update clk and cpufreq driversPavel Kubelun2018-01-1716-814/+388
| | | | | | | | | | | | | A newer clk and cpufreq drivers for ipq806x platform had been sent upstream. A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing). Following patches are removed: - 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer. - 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch. - 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: force 2nd pci slot into gen1 modePavel Kubelun2018-01-1710-13/+17
| | | | | | | | | | | | | | According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode. EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode. In previous commit we've added the support for this option, so enable it in DT for affected devices. QSDK ref: https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506 While at it move the phy transmit termination offset value into dtsi file as it's platform specific. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix wireless regressionPavel Kubelun2018-01-1710-308/+734
| | | | | | | | | | | | | | | | In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues. https://bugs.lede-project.org/index.php?do=details&task_id=1197 This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant Unfortunately qca developers do not bother to push it upstream. Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration. Fixes: FS#1197 and probably others Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* tools/cmake: update to 3.10.1Hannu Nyman2018-01-177-40/+16
| | | | | | | Update cmake to 3.10.1 Refresh patches Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/scons: update to 3.0.1Hannu Nyman2018-01-172-3/+3
| | | | | | Update scons to 3.0.1 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/libressl: update to 2.6.4Hannu Nyman2018-01-171-2/+2
| | | | Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* xtables-addons: remove from baseJo-Philipp Wich2018-01-166-19989/+0
| | | | | | | The package has been moved to the package feed repository to allow for non-base dependencies such as Perl. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* netfilter: enable CONFIG_NF_CONNTRACK_MARK from kmod-nf-conntrackJo-Philipp Wich2018-01-161-0/+1
| | | | | | | | Unconditionally enable connmark support and tie it to the conntrack core module to allow removing this kernel configuration dependency from the xtables-addons package. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* feeds: switch git.lede-project.org URLs to git.openwrt.orgJo-Philipp Wich2018-01-161-4/+4
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* iwinfo: update to latest git HEADJo-Philipp Wich2018-01-161-3/+3
| | | | | | 5a5e21b nl80211: skip event notifications in wpa_supplicant scan result reply Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* dnsmasq: use SIGINT for dnssec time validKevin Darbyshire-Bryant2018-01-153-2/+122
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dnsmasq used SIGHUP to do too many things: 1) set dnssec time validation enabled, 2) bump SOA zone serial, 3) clear dns cache, 4) reload hosts files, 5) reload resolvers/servers files. Many subsystems within LEDE can send SIGHUP to dnsmasq: 1) ntpd hotplug (to indicate time is valid for dnssec) 2) odhcpd (to indicate a new/removed host - typically DHCPv6 leases) 3) procd on interface state changes 4) procd on system config state changes, 5) service reload. If dnssec time validation is enabled before the system clock has been set to a sensible time, name resolution will fail. Because name resolution fails, ntpd is unable to resolve time server names to addresses, so is unable to set time. Classic chicken/egg. Since commits 23bba9cb330cd298739a16e350b0029ed9429eef (service reload) & 4f02285d8b4a66359a8fa46f22a3efde391b5419 (system config) make it more likely a SIGHUP will be sent for events other than 'ntpd has set time' it is more likely that an errant 'name resolution is failing for everything' situation will be encountered. Fortunately the upstream dnsmasq people agree and have moved 'check dnssec timestamp enable' from SIGHUP handler to SIGINT. Backport the upstream patch to use SIGINT. ntpd hotplug script updated to use SIGINT. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: use blue status LED for Xiaomi Router 3GDaniel Gimpelevich2018-01-151-3/+1
| | | | | | | | | | | | The blue LED is what other firmwares use for this device, and it's a lot easier on the eyes than its shade of yellow, which implies an error condition. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [merge into existing $boardname:blue:status block] Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: Piotr Dymacz <pepe2k@gmail.com> Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: add support for TP-Link Archer C20 v4Maxim Anisimov2018-01-156-0/+191
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v4 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 3x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Flash instruction: The only way to flash LEDE image in ArcherC20v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1Maxim Anisimov2018-01-157-39/+37
| | | | | | | | This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1" because of TPLINK released new TP-Link Archer C20 v4. Additionally migration to the generic board detection has been made. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ar71xx: fix TP-Link Archer C7 v4 switch LEDsDavid Bauer2018-01-151-8/+12
| | | | | | | | Match mapping of the switch LEDs according to the TP-Link firmware behavior. LAN port 1 triggers the most right LAN LED, LAN port 2 the second LAN LED from the right and so on. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add image checksChen Minqiang2018-01-151-8/+5
| | | | | | | As long as we can't enforce image metadata, we need to use (platform) image checks to have at least soem kind of validation. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ipq806x: drop ubifs supportMathias Kresin2018-01-152-10/+1
| | | | | | | | Ubifs is disabled for all boards except the evaluation boards and the Fritz!Box 4040 anyway. According the author, the ubifs support for the Fritz!Box 4040 wasn't enabled on purpose. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop legacy image leftoversMathias Kresin2018-01-151-24/+0
| | | | | | | Remove leftover code used for legacy images. There are no relevant binary differences for the images after removing the legacy leftovers. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: unset filesystem specific build command by defaultMathias Kresin2018-01-151-0/+1
| | | | | | | | | | | | | Initialise the filesystem specific build command. Otherwise it will be unintended inherit to following images and will cause a wrong image format. The issue is around for ages but was only recently triggered due to the added support for the Openmesh a42. Fixes: FS#1276 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: remove unnecessary filesystem specific buildMathias Kresin2018-01-151-1/+1
| | | | | | The Openmesh factory image doesn't need a squashfs specific build command. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: use bin file extension for sysupgrade-tar imagesMathias Kresin2018-01-151-8/+8
| | | | | | | Use the file extension bin for sysupgrade-tar images to unify the file extension across the target/tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uqmi: fix raw-ip mode for newer lte modemsKoen Vandeputte2018-01-152-2/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some newer LTE modems, like the MC7455 or EC25-E do not support "802.3" mode, and will stay in "raw-ip" regardless of the mode being set. In this case, the driver must be informed that it should handle all packets in raw mode. [1] This commit fixes connectivity issues for these devices. Before: [ Node 5 ] udhcpc -i wwan0 udhcpc: started, v1.27.2 udhcpc: sending discover udhcpc: sending discover udhcpc: sending discover After: [ Node 5 ] udhcpc -i wwan0 udhcpc: started, v1.27.2 udhcpc: sending discover udhcpc: sending select for 100.66.245.226 udhcpc: lease of 100.66.245.226 obtained, lease time 7200 udhcpc: ifconfig wwan0 100.66.245.226 netmask 255.255.255.252 broadcast + udhcpc: setting default routers: 100.66.245.225 [1] https://lists.freedesktop.org/archives/libqmi- devel/2017-January/002064.html Tested on cns3xxx using a Sierra Wireless MC7455 LTE-A Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [bumped PKG_RELEASE] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: image: rework EnGenius ENS202EXT factory imagePiotr Dymacz2018-01-151-7/+4
| | | | | | | | | Current EnGenius ENS202EXT factory image recipe version causes factory images of the following devices to be corrupted. This issue wasn't visible until recent changes of image Makefile snippets order. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* tools: make-ext4fs: remove LEDE_GIT referencesJo-Philipp Wich2018-01-151-1/+1
| | | | | | | Change the make-ext4fs Makefile to use the common PROJECT_GIT variable instead. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* omap24xx: remove referece to not existing kmod-usb-musb-tusb6010Jo-Philipp Wich2018-01-151-1/+1
| | | | | | | | Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from the omap24xx target, the corresponding module is built into the kernel. Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* 6rd: pass ipcalc as argument to evalHans Dedecker2018-01-152-3/+3
| | | | | | | | Instead of grepping for NETWORK after calling ipcalc.sh; pass ipcalc.sh as argument to eval allowing to use $NETWORK to retrieve the IPv4 prefix (ip4prefix). Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)Roger Pueyo Centelles2018-01-159-10/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info. Specifications: - SoC: Qualcomm Atheros QCA9556 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive PoE in Working: - Board/system detection - Sysupgrade - Serial console - Ethernet - 2.4 GHz radio - 5 GHz radio - Reset button Not working: - LEDs (added according to Mikrotik's GPL sources but not functional) Unsupported: - ZT2046Q SPI temperature and voltage sensor Contributors: Giuseppe Tipaldi (@Ciusss89) Ricky (@rickydee) Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
* ar71xx: kernel: enable PCI on QCA9556 SoCRoger Pueyo Centelles2018-01-152-0/+24
| | | | | | | | | This patch enables the PCI bus on the QCA9556 SoC, the same way it is done on the same family SoC QCA9558. Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for ALFA Network AC1200RMPiotr Dymacz2018-01-156-6/+193
| | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN. Specification: - MT7620A (580 MHz) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4 - 2T2R 2.4 GHz (MT7620A) - 2T2R 5 GHz (MT7612EN) - 1x USB 2.0 - 9x LED (8 driven by GPIO) - 1x button (reset) - DC jack for main power input (12-24 V) - 2x UART, I2C, I2S and LED headers Flash instruction (do it under U-Boot, using UART and TFTP server): Select option "2: Load system code then write to Flash via TFTP" and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for GL.iNet GL-AR750Piotr Dymacz2018-01-151-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-AR750Piotr Dymacz2018-01-1515-10/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3x 10/100 Mbps Ethernet - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 1x USB 2.0 (power controlled by GPIO) - 1x microSD (GL857L) - 3x LED (all driven by GPIO) - 1x button (reset) - 1x 2-pos switch - header for optional PoE module - 1x micro USB for main power input - UART + I2C header on PCB Flash instruction: Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used to flash OpenWrt/LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: move Sitecom WLR-8100 from legacy to genericPiotr Dymacz2018-01-153-9/+10
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix Sitecom WLR-8100 supportDavide Fioravanti2018-01-156-14/+17
| | | | | | | | | | | | | | This patch fixes Sitecom WLR-8100: - mtd layout - LAN and WAN MAC address setup - 2.4 GHz Wi-Fi MAC address setup - 5 GHz Wi-Fi support (calibration data, MAC address setup, missing ath10k-* packages) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [squashed commits, fixed whitespace issues, reworded commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for ALFA Network R36APiotr Dymacz2018-01-151-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network R36APiotr Dymacz2018-01-1512-1/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36A is a successor of the previous model, the R36 (Ralink RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB - 1x USB 2.0 (power controlled by GPIO) - 6x LED (5 of them are driven by GPIO) - 2x button (reset, wifi/wps) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Teltonika RUT900Piotr Dymacz2018-01-1513-0/+267
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is an industrial 3G router based on Atheros AR9344. There are available 3 other models in RUT9xx series: RUT905, RUT950 and RUT955, which differ in availability of additional I/O ports, built-in GSM modem type, GPS antenna and other features. FCC ID of the RUT950 model (LTE module built-in): 2AET4-RUT950. This patch adds support for the RUT900 model only but can be easily extended to cover whole series. Also, as there are several different 3/4G modules (Huawei, Quectel, Telit) used in whole series, packages required for WWAN support are not included by default. It is up to the user to install required software for built-in modem. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA - built-in 3G module (example: Telit HE910-D) - 2x miniSIM slot - 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G) - PCA9539 16-bit GPIO I2C expander - 12x LED (4 are driven by AR9344, 7 by PCA9539) - 1x button (reset) - DC jack for main power input (9-30 V) - UART available on PCB edge connector Serial console pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for ALFA Network N5QPiotr Dymacz2018-01-141-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 17:45:46 +0000