aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* x86: fix kmod-forcedeth package selectionTomasz Maciej Nowak2020-04-203-3/+3
| | | | | | | | There's no such package as forcedeth, threfore the driver is never selected. Fix it by properly specifying package name. Fixes: 35f208d ("x86: add nforce eth to default packages") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: image: drop dead codeTomasz Maciej Nowak2020-04-201-8/+0
| | | | | | | These are remnants of old image generation code, which now serve no purpose. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* uboot-rockchip: fix ident stringPetr Štetiar2020-04-201-1/+1
| | | | | | | | Commit 797506011695 ("uboot-rockchip: add new package") has added `OpenWRT` ident string, fix it to proper `OpenWrt`. Fixes: 797506011695 ("uboot-rockchip: add new package") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* rockchip: add support for Pine64 RockPro64Tobias Mädel2020-04-2010-0/+1051
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds the new rockchip target and support for RockPro64 RK3399 Flash: 16 MiB SPI NOR RAM: 2 GiB/4 GiB LPDDR4 SoC: RK3399 USB: 2x USB 2.0, 1x USB 3.0, 1x USB-C Ethernet: 1x GbE PCIe: PCIe 2.0, 4 lanes Storage: eMMC or SD card Optional SDIO wifi/bt module The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector, 6 ARM64 cores (4 little, 2 big), plenty of RAM and storage. By default the single Gigabit-Ethernet port is configured as the LAN port. Installation of the firware is possible by dd'ing the image to an SD card or the eMMC flash. Serial: 3v3 1500000 8n1 U-boot is build from the mainline tree and integrated into the images. Required ATF to build u-boot is downloaded from a CI build bot. Signed-off-by: Tobias Mädel <t.maedel@alfeld.de> Tested-by: Tobias Schramm <t.schramm@manjaro.org>
* uboot-rockchip: add new packageTobias Mädel2020-04-201-0/+57
| | | | | | | This package is needed for the rockchip target. Signed-off-by: Tobias Mädel <t.maedel@alfeld.de> Tested-by: Tobias Schramm <t.schramm@manjaro.org>
* arm-trusted-firmware-rockchip: add new packageTobias Mädel2020-04-201-0/+49
| | | | | | | | | This is needed to build the uboot-rockchip, needed for the rockchip target Signed-off-by: Tobias Mädel <t.maedel@alfeld.de> Tested-by: Tobias Schramm <t.schramm@manjaro.org> [replaced `mkdir -p` with INSTALL_DIR variable] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* uboot-kirkwood: update to 2020.04Pawel Dembicki2020-04-2010-118/+101
| | | | | | | | | | | | | Update U-Boot to current 2020.04 release for kirkwood platform. Catch up with upstream and move some configuration options from the header files to the corresponding defconfig files. Compile tested: all devices Run tested: nsa310, pogoplugv4 Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: netfilter.mk: fix kmod-ipt-nat6 installation on 5.4DENG Qingfang2020-04-201-1/+0
| | | | | | | | | | xt_MASQUERADE.ko is picked up by both kmod-ipt-nat and kmod-ipt-nat6, causing conflict As kmod-ipt-nat6 already depends on kmod-ipt-nat, remove xt_MASQUERADE from it Fixes: FS#2924 Fixes: 0fad8af85158 ("kernel: Include xt_MASQUERADE for kernel 5.2 and later") Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* relayd: bump to version 2020-04-20Kevin Darbyshire-Bryant2020-04-201-3/+3
| | | | | | | | 796da66 dhcp.c: improve input validation & length checks Addresses CVE-2020-11752 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* umdns: update to version 2020-04-20Kevin Darbyshire-Bryant2020-04-201-4/+4
| | | | | | | | e74a3f9 dns.c: improve input validation Addresses CVE-2020-11750 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: mt7621: add NETGEAR R7200 as DEVICE_ALT1Pawel Dembicki2020-04-201-0/+4
| | | | | | | | Netgear R7200 is another clone of Netgear R6700v2, introduced in: 6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400") Reported-by: Joel Pinsker, github user @joelp64 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* procd: fix jail when running on glibcDaniel Golle2020-04-191-3/+3
| | | | | | d200b70 jail: include /etc/nsswitch.conf in jail for glibc. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for AVM FRITZ!WLAN Repeater 450EDavid Bauer2020-04-198-90/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the device afterwards to boot OpenWRT. Tested-by: Andreas Ziegler <dev@andreas-ziegler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: replace pinctrl property names for ipTIME A1004nsSungbo Eo2020-04-191-2/+2
| | | | | | | | | | The pinctrl driver had been replaced with the upstream one in b756ea2a909a ("ramips: replace pinctrl property names"), but the initial A1004ns support patch did not reflect the changes. This commit updates its pinctrl property names. Fixes: 9169482f640c ("ramips: add support for ipTIME A1004ns") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* toolchain: glibc: Define minimum support kernel version as 4.14Hauke Mehrtens2020-04-181-1/+2
| | | | | | | This will compile glibc in a way that it will only support kernel 4.14 and later. Compatibility code for older kernel versions will be removed. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* toolchain: glibc: Update glibc to version 2.31Hauke Mehrtens2020-04-184-30/+690
| | | | | | | | | | | | | | | This updates glibc to the most recent version 2.31. 001-regex-read-overrun.patch was a backport from a more recent version and is integrated in glibc 2.31. 050-Revert-Disallow-use-of-DES-encryption-functions-in-n.patch is needed to add the DES crypto functions back again. They were removed in glibc 2.28, but we still use them in ppp. musl lib also provides these DES crypto functions. Without them we would have to link ppp against openssl or an other crypto library. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* dante: Fix compile with glibcHauke Mehrtens2020-04-182-1/+54
| | | | | | | | | | | | | | | | | | | When compiled with glibc the config_scan.c wants to use the cpupolicy2numeric() function which is only available when HAVE_SCHED_SETSCHEDULER is set. It looks like the wrong define was used here. This fixes a build problem with glibc in combination with the force ac_cv_func_sched_setscheduler=no in the OpenWrt CONFIGURE_VARS. This fixes the following compile error with glibc: ---------------------------------------------------------------------- /bin/ld: config_scan.o: in function `socks_yylex': dante-1.4.1/sockd/config_scan.l:461: undefined reference to `cpupolicy2numeric' collect2: error: ld returned 1 exit status make[5]: *** [Makefile:522: sockd] Error 1 Fixes: aaf46a8fe23e ("dante: disable sched_getscheduler() - not implemented in musl") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* rbcfg: Add missing mode to open callHauke Mehrtens2020-04-182-2/+2
| | | | | | | | | | | | | | | | | | | When open() is called with O_CREAT a 3. parameter has to be given with the file system permissions of the new file. Not giving this is an error, which results in a compile error with glibc. This fixes the following compile error with glibc: ---------------------------------------------------------------------- In file included from /include/fcntl.h:329, from main.c:18: In function 'open', inlined from 'rbcfg_update' at main.c:501:7: /include/bits/fcntl2.h:50:4: error: call to '__open_missing_mode' declared with attribute error: open with O_CREAT or O_TMPFILE in second argument needs 3 arguments __open_missing_mode (); ^~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* upgs: Remove extra _DEFAULT_SOURCE definitionHauke Mehrtens2020-04-181-4/+0
| | | | | | | | | | | | | | | This extra _DEFAULT_SOURCE definition results in a double definition which is a compile error. This fixes the following compile error with glibc: ---------------------------------------------------------------------- ugps-2019-06-25-cd7eabcd/nmea.c:19: error: "_DEFAULT_SOURCE" redefined [-Werror] #define _DEFAULT_SOURCE <command-line>: note: this is the location of the previous definition cc1: all warnings being treated as errors Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* busybox: backport Remove stime() function callsHauke Mehrtens2020-04-181-0/+84
| | | | | | | glibc 2.31 does not provide stime() any more, backport a fix from current busybox master to avoid using this function. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm63xx: switch to 5.4 kernelÁlvaro Fernández Rojas2020-04-181-2/+1
| | | | | | | Seems stable after 6 days of testing on some of my devices. Let's switch to 5.4 in order to get more feedback. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* openvpn: update to 2.4.9Magnus Kroken2020-04-183-4/+4
| | | | | | | | | | | | | | | This is primarily a maintenance release with bugfixes and improvements. This release also fixes a security issue (CVE-2020-11810) which allows disrupting service of a freshly connected client that has not yet negotiated session keys. The vulnerability cannot be used to inject or steal VPN traffic. Release announcement: https://openvpn.net/community-downloads/#heading-13812 Full list of changes: https://community.openvpn.net/openvpn/wiki/ChangesInOpenvpn24#OpenVPN2.4.9 Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* binutils: add ALTERNATIVES for strings (FS#3001)Hans Dedecker2020-04-181-1/+2
| | | | | | | | Don't move strings anymore to /bin/strings to avoid clash with busybox /usr/bin/strings but move it to /usr/bin/binutils-strings. Use ALTERNATIVES support to install it as /usr/bin/strings Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: mt7621: use lzma-loader for newifi d1/d2/thunder timecloudChuanhong Guo2020-04-181-0/+3
| | | | | | | These devices failed to properly extract kernel. enable lzma loader for them. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: don't reuse KERNEL_DTB for lzma-loaderChuanhong Guo2020-04-181-1/+1
| | | | | | | | mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed for our lzma loader. This saves 15KB on mt7621 devices using uimage-lzma-loader. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: backport more pcie driver fixesChuanhong Guo2020-04-183-5/+226
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: increase spi-max-frequency for ipTIME mt7620 devicesSungbo Eo2020-04-181-1/+1
| | | | | | | | | | | | This commit increases the hardware SPI frequency from 24.2MHz to 48.3MHz. [ 5.314163] m25p80 spi0.0: speed: 24166666/40000000, rate: 8, prescal: 2, loops: 226 [ 5.076323] m25p80 spi0.0: speed: 48333333/50000000, rate: 4, prescal: 1, loops: 162 `time cat /dev/mtd2 >/dev/null` is reduced from 5.64s to 4.36s on A104ns, and from 11.39s to 8.81s on A1004ns. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME A1004nsSungbo Eo2020-04-183-1/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A1004ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610EN - Ethernet: 5x 10/100/1000Mbps - Switch: MT7530BU - USB: 1x 2.0 - UART: - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7621: Ubiquiti ER-X-SFP: fix gpio numbers for POE enable gpiosRené van Dorst2020-04-181-5/+5
| | | | | | | With v5.4 kernel a new gpio driver is used. GPIO numbering has changed so update 03_gpio_switches too. Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: mt7621: Ubiquiti ER-X: fix gpio number for POE enable gpioRené van Dorst2020-04-181-1/+1
| | | | | | | With v5.4 kernel a new gpio driver is used. GPIO numbering has changed so update 03_gpio_switches too. Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: use all reserved space for HiWiFi HC5962DENG Qingfang2020-04-182-33/+23
| | | | | | | | These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt" do not contain any device-specific data and can be used for /overlay, resulting in 121M space Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: increase HiWiFi HC5962 kernel partition to 4MDENG Qingfang2020-04-182-7/+4
| | | | | | | | | | | | | | | | | | Increase kernel partition because 2M is insufficient for 5.4 Because the partition changes, previous version of OpenWrt cannot upgrade to this version, and requires a new installation Recovery to stock instruction: 1. Download stock firmware at http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin 2. Power off the router 3. Press and hold the reset button for 4~6 sec while power it back on 4. Connect a PC to router's LAN 5. Visit http://192.168.2.1 and upload the firmware Then repeat the instruction in edae3479e64e to install OpenWrt Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* generic: spi-nor: fix 4-byte opcode support for w25q256Mantas Pucka2020-04-181-0/+60
| | | | | | | | | | There are 2 different chips (w25q256fv and w25q256jv) that share the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes. Use SFDP header version to differentiate between them. Fixes broken reboot on 8devices Habanero since f0f35fdac Signed-off-by: Mantas Pucka <mantas@8devices.com>
* mbedtls: update to 2.16.6Magnus Kroken2020-04-171-2/+2
| | | | | | | | | | | | Security fixes for: * CVE-2020-10932 * a potentially remotely exploitable buffer overread in a DTLS client * bug in DTLS handling of new associations with the same parameters Full release announement: https://tls.mbed.org/tech-updates/releases/mbedtls-2.16.6-and-2.7.15-released Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* kernel: bump 5.4 to 5.4.33Petr Štetiar2020-04-1710-147/+14
| | | | | | | | | | | | Refreshed patches, removed upstreamed patches: oxnas: 001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch oxnas: 002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch Run tested: qemu-x86-64, apalis Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mac80211: make sure existing iface belongs to correct (fullmac) phyDaniel Golle2020-04-172-9/+19
| | | | | | | | | | | | | | Some FullMAC cfg80211 wireless devices do not support virtual interfaces, hence there is script logic to keep the existing network device. Improve this to support renaming the interface if needed and make sure the existing interface actually belongs to the right phy. Change calls to 'iw' to avoid outputing warnings and errors to not confuse users of such devices. Also bump PKG_RELEASE which has been forgotten in the previous two mac80211 changes. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: remove stray pipeDavid Bauer2020-04-171-1/+1
| | | | | | Fixes: 8918c038f330 ("ath79: add support for AVM FRITZ!WLAN Repeater 1750E") Signed-off-by: David Bauer <mail@david-bauer.net>
* elfutils: aarch64 fix build on muslLucian Cristian2020-04-171-0/+59
| | | | | | | | | aarch64_initreg.c: In function 'aarch64_set_initial_registers_tid': aarch64_initreg.c:85:37: error: invalid operands to binary & (have 'long double' and 'unsigned int') dwarf_fregs[r] = fregs.vregs[r] & 0xFFFFFFFF; ~~~~~~~~~~~~~~ ^ Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* uboot-sunxi: bump to 2020.04 relasePetr Štetiar2020-04-179-43/+14
| | | | | | | | | | | Refreshed patches, removed upstreamed patch: 260-configs-a64-olinuxino-emmc-add-eMMC-boot-part-config.patch Boot tested on a64-olinuxino-emmc. Cc: Zoltan HERPAI <wigyori@uid0.hu> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* uboot-imx6: bump to 2020.04 releasePetr Štetiar2020-04-174-13/+11
| | | | | | | | | Refreshed all patches, run tested on apalis. Cc: Vladimir Vid <vladimir.vid@sartura.hr> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mac80211: drop data frames without key on encrypted linksDavid Bauer2020-04-171-0/+148
| | | | | | | | | | | | | | | | | | | | | | | | | If we know that we have an encrypted link (based on having had a key configured for TX in the past) then drop all data frames in the key selection handler if there's no key anymore. This fixes an issue with mac80211 internal TXQs - there we can buffer frames for an encrypted link, but then if the key is no longer there when they're dequeued, the frames are sent without encryption. This happens if a station is disconnected while the frames are still on the TXQ. Detecting that a link should be encrypted based on a first key having been configured for TX is fine as there are no use cases for a connection going from with encryption to no encryption. With extended key IDs, however, there is a case of having a key configured for only decryption, so we can't just trigger this behaviour on a key being configured. Cc: stable@vger.kernel.org Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for AVM FRITZ!WLAN Repeater 1750EDavid Bauer2020-04-177-13/+237
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!WLAN Repeater 1750E SOC: Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 WLAN2: QCA9880 5 GHz 802.11 n/ac 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (correct MAC) - 5 GHz WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the Device afterwards to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add QCA9550 reset sequenceDavid Bauer2020-04-177-2/+280
| | | | | | | | | | | | | | | | | The QCA9550 family of SoCs have a slightly different reset sequence compared to older chips. Normally the bootloader performs this sequence, however some bootloader implementation expect the operating system to clear the reset. Also get the PCIe resets from OF to support the second RC of the QCA9558. This is required for the AVM FRITZ!WLAN Repeater 1750E to work, as EVA leaves the PCIe bus in reset. Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: fix detecting existing interfaceDaniel Golle2020-04-171-1/+1
| | | | | | | | | Instead of using the actual interface name, a hard-coded 'wlan0' has slipped into the script. Replace it. Fixes: ccf2aa9d4b ("mac80211: detect existing interface before adding") Reported-by: John Crispin <john@phrozen.org> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: add support for GD25D05 SPI NOR (5.4)Koen Vandeputte2020-04-161-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | This chip is used on newer RB912UAG-5HPnD r2 and 922UAGS-5HPacD boards: Before: [ 0.824562] spi-nor spi0.0: unrecognized JEDEC id bytes: c8 40 10 c8 40 10 [ 0.831607] spi-nor: probe of spi0.0 failed with error -2 After: [ 0.825347] spi-nor spi0.0: gd25d05 (64 Kbytes) [ 0.830291] 1 routerbootpart partitions found on MTD device spi0.0 [ 0.836577] Creating 1 MTD partitions on "spi0.0": [ 0.841448] 0x000000000000-0x000000010000 : "partitions" [ 0.848418] 4 routerbootpart partitions found on MTD device partitions [ 0.855092] Creating 4 MTD partitions on "partitions": [ 0.860318] 0x000000000000-0x00000000c000 : "routerboot" [ 0.866548] 0x00000000c000-0x00000000d000 : "hard_config" [ 0.872832] 0x00000000d000-0x00000000e000 : "bios" [ 0.878580] 0x00000000e000-0x00000000f000 : "soft_config" Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: reduce spi-max-frequency for Mikrotik wAP G-5HacT2HnDRoger Pueyo Centelles2020-04-161-1/+1
| | | | | | | | The previous spi-max-frequency value did not work with all the CPU speed settings (configurable with rbcfg or from the stock firmware); the new one does for the three of them. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: MikroTik: fix missing nand on kernel 5.4Koen Vandeputte2020-04-161-0/+1
| | | | | | | | | | | | | | | | | | | | | Following symbol got renamed upstream: CONFIG_MTD_NAND --> CONFIG_MTD_RAW_NAND Also add this renamed symbol so NAND also works on kernel 5.4. After: [ 0.628372] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 0.634862] nand: Samsung NAND 128MiB 3,3V 8-bit [ 0.639554] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.647263] Scanning device for bad blocks [ 0.656228] random: fast init done [ 0.789652] 3 fixed-partitions partitions found on MTD device ar934x-nand [ 0.796550] Creating 3 MTD partitions on "ar934x-nand": [ 0.801874] 0x000000000000-0x000000040000 : "booter" [ 0.807715] 0x000000040000-0x000000400000 : "kernel" [ 0.813551] 0x000000400000-0x000008000000 : "ubi" Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.115Koen Vandeputte2020-04-1647-294/+110
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch - 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch Fixes: - CVE-2020-8647 - CVE-2020-8648 (potentially) - CVE-2020-8649 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.176Koen Vandeputte2020-04-1624-325/+82
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch - 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch - 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch Fixes: - CVE-2020-8648 (potentially) - CVE-2020-8647 - CVE-2020-8649 Compile-tested on: cns3xxx, octeontx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: improve status LED definitions for GL-AR750Hannu Nyman2020-04-161-1/+5
| | | | | | | | Improve the status LED functionality in GL-AR750 by adding the definitions for different statuses (boot, failsafe, running, flashing). Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-29 03:21:14 +0000