aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ltq-vdsl-mei: avoid underscore in package nameSungbo Eo2020-02-231-4/+4
| | | | | | | As 07e1d88d7beb ("kernel: avoid underscore in *6lowpan package names") shows, underscores might cause build failures. Replace underscore with dash. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: move includes to DTSI for mt7628an_tplink_8m*Adrian Schmutzler2020-02-2213-33/+6
| | | | | | | | | | All devices inherited from mt7628an_tplink_8m.dtsi and mt7628an_tplink_8m-split-uboot.dtsi contain the same additional includes in the DTS files. Move them to the DTSI files instead. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move compatible for Ubiquiti Edgerouter X to DTS fileAdrian Schmutzler2020-02-222-2/+1
| | | | | | | | | | | | So far, the compatible for the Ubiquiti Edgerouter X has been defined in the DTSI file and inherited for the edgerouterx.dts, but overwritten for the edgerouterx-sfp.dts. In contrast, the model was stored in the DTS file in both cases. To resolve this somewhat confusing situation, move the compatible with the device name for edgerouterx to the DTS file as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant includes in DTS filesAdrian Schmutzler2020-02-227-15/+2
| | | | | | | | | | Many DTS files contain the same includes again that are already present in the DTSI files they are derived from. Remove those redundant includes in the DTS files. For vocore, the include is moved to the parent DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove redundant includes in DTS filesAdrian Schmutzler2020-02-2217-50/+0
| | | | | | | | | Many DTS files contain the same includes again that are already present in the DTSI files they are derived from. Remove those redundant includes in the DTS files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* packages/boot: bump arm-trusted-firmware-mvebu versionScott Roberts2020-02-221-4/+4
| | | | | | | The current version of ATF does not support power off for SGMII COMPHY. Update to latest ATF to resolve this issue. Signed-off-by: Scott Roberts <ttocsr@gmail.com>
* mac80211: backport fix TID field in monitor mode transmitFredrik Olofsson2020-02-221-0/+45
| | | | | | Backport 753ffad3d6243303994227854d951ff5c70fa9e0 as merged in Linux v5.5-rc3. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
* kernel: fix xt_connmark.hMartin Schiller2020-02-221-2/+2
| | | | | | | | | Commit a1cfe0dcbb24 (kernel: connmark set-dscpmark follow upstreamimg attempt") broke the usage of xt_connmark.h in user-space (e.g. strongswan), because the BIT() macro is unknown there. Fixes: a1cfe0dcbb24 (kernel: connmark set-dscpmark follow upstreamimg attempt") Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* toolchain/binutils: Add binutils 2.34Daniel Engberg2020-02-226-3/+93
| | | | | | | Refresh patches Drop 300-012_check_ldrunpath_length.patch Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* package/utils/f2fs-tools: Update to 1.13.0Daniel Engberg2020-02-223-63/+4
| | | | | | | | Update f2fs-tools to 1.13.0 Remove upstreamed patches Disable build of static library Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* generic: refresh patchesAleksander Jan Bajkowski2020-02-223-47/+8
| | | | | | | | just run: make target/linux/refresh V=s Fixes: 6e315de0f422acf66c3505a4ed8c095a0f5d3424 Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* usbmode: Update modeswitch data to 20191128Davide Fioravanti2020-02-221-2/+2
| | | | | | Add support for new hardware Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* kernel: remove non-existant symbols from 4.19 configAleksander Jan Bajkowski2020-02-226-17/+0
| | | | | | These symbols only exist in kernel version <= 4.15 Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* kernel: replace SUBDIRS with M in package recipesTomasz Maciej Nowak2020-02-2218-21/+21
| | | | | | | The SUBDIRS variable has been removed in kernel 5.4, and was deprecated since the beginnig of kernel git history in favour of M or KBUILD_EXTMOD. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* linux-firmware: update to 20200122DENG Qingfang2020-02-221-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update linux-firmware to 20200122 git log --pretty=oneline --abbrev-commit 20191215..20200122 1eb2408 linux-firmware: Update firmware file for Intel Bluetooth AX200 0dc1611 linux-firmware: Update firmware file for Intel Bluetooth AX201 d03f79c linux-firmware: Update firmware file for Intel Bluetooth 9560 aab62bc linux-firmware: Update firmware file for Intel Bluetooth 9260 ed0aa3a nvidia: add TU102/TU104/TU106 signed firmware 9c340bd amdgpu: update navi10 firmware for 19.50 3b4a503 amdgpu: Add navi10 TA ucode 16cc13a Merge branch 'v1.1.3' of https://github.com/ruiwang-mtk/linux_fw_vpu_v1.1.37f3177d mediatek: update MT8173 VPU firmware to v1.1.3 67d4ff5 Mellanox: Add new mlxsw_spectrum firmware xx.2000.2714 f1c9e7b radeon: update oland rlc microcode from amdgpu b1dafb7 amdgpu: update vega20 microcode for 19.50 c38789e amdgpu: update vega12 microcode for 19.50 5a141c1 amdgpu: update vega10 microcode for 19.50 a03173a amdgpu: update picasso microcode for 19.50 86e9a5f amdgpu: update raven2 microcode for 19.50 febe09a amdgpu: update raven microcode for 19.50 af76fd0 amdgpu: update navi10 microcode for 19.50 b5b176a amdgpu: update navi14 microcode for 19.50 ad90178 amdgpu: add TA microcode for Raven asics 379551b qed: Add firmware 8.42.2.0 58b4003 Merge branch 'RB3-wlan-firmware-1387-v2' of https://github.com/andersson/linux-firmware 5967a45 Adjust WHENCE entry to check_whence doesn't complain d1e743d Merge branch 'master' of https://github.com/NXP/mwifiex-firmware d6219ab qcom: Switch SDM845 WLAN firmware e65245c linux-firmware: add NXP firmware licence file 6871bff Merge branch 'ath10k-20191220' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware b142c2e ath10k: WCN3990 hw1.0: add firmware WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 8809b87 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00070 513d70c ath10k: QCA988X hw2.0: update firmware-5.bin to 10.2.4-1.0-00047 203435b ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00070 a66d2fc ath10k: QCA9887 hw1.0: update firmware-5.bin to 10.2.4-1.0-00047 6d19154 ath10k: QCA6174 hw3.0: update board-2.bin c4586ff linux-firmware: Update AMD cpu microcode Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* iw: update to 5.4DENG Qingfang2020-02-223-118/+43
| | | | | | | Update iw to 5.4 This increases the ipk size of iw-tiny/full by about 400 bytes Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* libbsd: update to 0.10.0Rosen Penev2020-02-224-295/+6
| | | | | | | | | | Removed all upstream patches. Added PKG_BUILD_PARALLEL for faster compilation. Small Makefile rearrangements for consistency between packages. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* build: Add additional kernel debug optionsHauke Mehrtens2020-02-223-0/+78
| | | | | | | | Make it possible to activate some additional kernel debug options. This can be used to debug some problems in kernel drivers. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com> Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* build: Add KCOV kernel code coverage for fuzzingHauke Mehrtens2020-02-221-0/+33
| | | | | | | The adds an option to activate KCOV (Code coverage for fuzzing). Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com> Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* build: Add option KERNEL_KASANHauke Mehrtens2020-02-223-0/+54
| | | | | | | | The kernel kernel address sanitizer is able to detect some memory bugs in the kernel like out of range array accesses. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com> Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* build: Add option KERNEL_UBSANHauke Mehrtens2020-02-223-0/+42
| | | | | | | | The kernel Undefined Behavior Sanitizer is able to detect some memory bugs in the kernel like out of range array accesses. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com> Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* x86: Add missing kernel option CONFIG_X86_DECODER_SELFTESTHauke Mehrtens2020-02-222-0/+2
| | | | | | | | | This option has now a different dependency and can be activated, set a default value. Fixes: 20b5a4ca01ca ("kernel: bump 4.19 to 4.19.101") Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com> Tested-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* rssileds: add dependencies based on LDFLAGSAdrian Schmutzler2020-02-221-1/+1
| | | | | | | | | | | | | | | | | This adds the direct dependencies introduced by TARGET_LDFLAGS to the package's DEPENDS variable. This was found by accidentally building rssileds on octeon, which resulted in: "Package rssileds is missing dependencies for the following libraries: libnl-tiny.so" Though the dependencies are provided when building for the relevant targets ar71xx, ath79 and ramips, it seems more tidy to specify them explicitly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: do not expose status LED to user config by defaultAdrian Schmutzler2020-02-221-23/+0
| | | | | | | | | | | | So far, the state of status LEDs is set up in 01_leds for many devices in kirkwood target. As those LEDs are also controlled by diag.sh, exposing them to the user via uci config by default seems not helpful and might even have confusing results for the user. Thus, remove the ucidef_set_led_default setup for power/status LED, but do not touch the rest where user control is actually a feature. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: set default state for status LEDs in device treeAdrian Schmutzler2020-02-2226-50/+78
| | | | | | | | | | This adds the default-state = "on"; statement for the power or primary status LED in DTS on kirkwood. This will ensure that this LED will be lit up very early in the boot process (i.e. before diag.sh is executed) and thus will provide an additional hint to the user when problems arise during early boot process. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: add diag LEDs for ZyXEL NSA325Adrian Schmutzler2020-02-222-0/+60
| | | | | | | This device has had no diag LEDs set up so far, so let's just add them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: use generic diag.shPawel Dembicki2020-02-2225-113/+542
| | | | | | | | | | | | | | | | | | This commit removes the target-specific diag.sh script. This way, the generic one is used for the target, which uses DT-aliases to specify the LEDs used. Generic diag.sh allow to use different LEDs to indicate different states. Non-red status LEDs for indicating boot and a running system. Where possible, the red or orange LEDs are used to indicate failsafe mode and a running upgrade. Compile-tested: all target devices. Run-tested: CheckPoint L-50 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [remove unrelated cosmetic changes, rename some labels, add pogo_e02] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lldpd: bump to 1.0.5Stijn Tintel2020-02-223-23/+4
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ath79: add support for Teltonika RUT955Daniel Golle2020-02-214-0/+397
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344) - built-in 4G/3G module (example: Quectel EC-25EU) - internal microSD slot (spi-mmc, buggy and disabled for now) - RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0) - RS422/RS485 (AR934x high speed UART, /dev/ttyATH1) - analog 0-24V input (MCP3221) - various digital inputs and outputs incl. a relay - 11x LED (4 are driven by AR9344, 7 by 74HC595) - 2x miniSIM slot (can be swapped via GPIO) - 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS) - 1x button (reset) - DC jack for main power input (9-30 V) - debugging UART available on PCB edge connector Serial console (/dev/ttyS0) pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2". Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* serial: ar933x_uart: add rs485 supportDaniel Golle2020-02-211-0/+271
| | | | | | | | | Add support for RS485 tranceiver with transmit/receive switch hooked to a RTS GPIO pin. Use the 'rts-gpios' and 'rs485-rts-active-low' properties as described in devicetree/bindings/serial/rs485.yaml. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for TP-Link TL-WA701ND/730RE/801ND/901ND v1Adrian Schmutzler2020-02-218-1/+89
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the various clones of the TL-WA830RE recently supported in fb99ac6807f2 ("ath79: add support for TP-Link TL-WA830RE v1"): - tplink,tl-wa701nd-v1 - tplink,tl-wa730re-v1 - tplink,tl-wa801nd-v1 - tplink,tl-wa830re-v1 (already supported) - tplink,tl-wa901nd-v1 Since these devices are 100%-clones in ar71xx, this patch adds all of them without run-testing (as this has been done for TL-WA830RE v1). Specifications: - SOC: Atheros AR7240 - CPU: 400MHz - Flash: 4 MiB (Spansion S25FL032P) - RAM: 32 MiB (Zentel A3S56D40FTP-G5) - WLAN: Atheros AR9280 bgn 2x2 - Ethernet: 1 port (100M) Flash instructions: - install from u-boot with tftp (requires serial access) > setenv ipaddr a.b.c.d > setenv serverip e.f.g.h > tftpboot 0x80000000 \ openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin > erase 0x9f020000 +0x3c0000 > cp.b 0x80000000 0x9f020000 0x3c0000 > bootm 0x9f020000 - flash factory image from OEM WebUI - sysupgrade from ar71xx image Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix HiWiFi HC5761A USB portDENG Qingfang2020-02-211-1/+12
| | | | | | Export GPIO 41 to power USB port Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by defaultPetr Štetiar2020-02-201-9/+3
| | | | | | | | | | | | | | | | | | | | | | | | Looking at the current upstream driver implementation, it seems like the TX/RX flow control is enabled only if the flow control pause option is resolved from the device/link partner advertisements (or otherwise set). On the other hand, our current in-tree driver force enables TX/RX flow control by default, thus possibly leading to TX timeouts if the other end sends pause frames (which are not properly handled?): WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324 NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out Disabling the flow control on PORT 5 MAC seems to fix this issues as the pause frames are then filtered out. While at it, I'm removing the if condition completely as suggested, since this code is run only on mt7621 SoC, so there is no need to check for the silicon revisions. Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12 Suggested-by: Felix Fietkau <nbd@nbd.name> Reported-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mt76: update to the latest versionFelix Fietkau2020-02-201-3/+3
| | | | | | | | f4415afce213 mt76: mt76u: loop over all possible rx queues in mt76u_rx_tasklet 5b9f949cb760 mt76: mt76u: fix a possible memory leak in mt76u_init fd892bc033fb mt76: mt76u: rely only on data buffer for usb control messagges Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: correct Siemens WS-AP3610 blocksizeDavid Bauer2020-02-201-0/+1
| | | | | | | With the wrong blocksize, the rootfs was not positioned on the boundary of a block, thus breaking the mtdsplit driver. Signed-off-by: David Bauer <mail@david-bauer.net>
* ppp: backport security fixesPetr Štetiar2020-02-204-1/+129
| | | | | | | | 8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP 8d7970b8f3db pppd: Fix bounds check in EAP code 858976b1fc31 radius: Prevent buffer overflow in rc_mksid() Signed-off-by: Petr Štetiar <ynezz@true.cz>
* util-linux: Update to 2.35.1Daniel Engberg2020-02-203-6/+6
| | | | | | | | Update util-linux to 2.35.1 and refresh patches. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [commit subject and description tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add label MAC address for Ubiquiti Picostation M (XM)Adrian Schmutzler2020-02-191-0/+1
| | | | | | | This adds the label MAC address for the Ubiquiti Picostation M (XM). This was overlooked when adding support in the previous patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti Picostation M (XM)Adrian Schmutzler2020-02-195-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti Picostation M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - External antenna: 5 dBi (USA), 2 dBi (EU) - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti Nanostation Loco M (XM)Sven Roederer2020-02-195-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti Nanostation Loco M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - NS Loco M2: built-in antenna: 8 dBi; AR9287 - NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Note that only certain firmware versions accept unsigned images. Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin Tested on NanoStation Loco M2. Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloaderAdrian Schmutzler2020-02-193-10/+4
| | | | | | | | | | | Several devices with tplink-safeloader contain default values (0x0) for TPLINK_HWID and TPLINK_HWREV in their device definitions. Move those to common tplink-safeloader definition so they do not have to be repeated each time. While at it, set default value for tplink-v1 and tplink-v2 as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mt76: update to the latest versionFelix Fietkau2020-02-191-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | bd0df1b017a8 mt76: avoid extra RCU synchronization on station removal d5a5e97b67c7 mt76: mt76x2: avoid starting the MAC too early a67e42990d8a mt76: mt7615: fix msdu_id endianness in mt7615_write_hw_txp d3af8bd3c722 mt76: mt7615: set proper length in strncmp 9c43417db17c mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap 764e1d208a06 mt76: mt7615: fix tx power reporting 1881241c7ee5 mt76: fix rounding issues on converting per-chain and combined txpower fa14e7f33199 mt76: mt7615: rework rx phy index handling a205ce3e3e2d mt76: mt7615: fix ext_phy flag for stations 457a93203690 mt76: mt7615: fix MT_TX_HW_QUEUE_EXT_PHY to deal with mac80211 changes c75cf513c674 mt76: do not set HOST_BROADCAST_PS_BUFFERING for mt7615 cc56c400167c mt76: fix LED link time failure 4dbd56b86970 mt76: mt76x0u: add support to TP-Link T2UHP e226309c4bc4 mt76: mt7615: rely on mt76_queues_read for mt7622 c6a025318075 mt76: mt76u: extend RX scatter gather number dfc24bc504e3 mt76: mt76u: rename stat_wq in wq 2bbffd2cb37b mt76: mt7615: remove rx_mask in mt7615_eeprom_parse_hw_cap f408a2b7566c mt76: Introduce mt76_mcu data structure 17ecf0762542 mt76: mt76x02: fix handling MCU timeouts during hw restart 284e9fd72912 mt76: mt7615: fix monitor injection of beacon frames 8f8e9161b355 mt76: fix array overflow on receiving too many fragments for a packet Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: avoid underscore in *6lowpan package namesEneas U de Queiroz2020-02-192-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | Packages kmod-bluetooth_6lowpan and kmod-ieee802154_6lowpan contain an underscore in the package name. This causes problems in package/install because when building a list of package files to install offline using opkg, it uses a wildcard of the form $(dir)/$(pkg)_*.ipk. If you were to select kmod-bluetooth=y, but kmod-bluetooth_6lowpan=m, the latter would be picked up by that wildcard, and make package/install would fail: Collected errors: * satisfy_dependencies_for: Cannot satisfy the following dependencies * for kmod-bluetooth_6lowpan: * kmod-6lowpan * opkg_install_cmd: Cannot install package kmod-bluetooth_6lowpan. Changing the wildcard pattern is not trivial, and there may be other places in the build system making this assumption about the package name format. Using a dash in place of the underscore avoids the issue. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* dnsmasq: fix uci-defaults script to exit 0 so it is cleaned upRussell Senior2020-02-191-0/+2
| | | | | | | | | | A file, package/network/services/dnsmasq/files/50-dnsmasq-migrate-resolv-conf-auto.sh, was added in commit 6a2855212096d2c486961a0841b037bae4b75de7, but it does not exit in a way that tells the uci-defaults mechanism that it succeeded, and so it is not cleaned up after running successfully. Add an exit 0 to the end to correct that. Signed-off-by: Russell Senior <russell@personaltelco.net>
* tools/bison: Update to 3.5.1Daniel Engberg2020-02-191-3/+3
| | | | | | | | Update bison to 3.5.1 Use POSIX threads as the previous option is no longer valid Disable NLS support to be consistent with other tools such as e2fsprogs and sed Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/e2fsprogs: Update to 1.45.5Daniel Engberg2020-02-181-3/+4
| | | | | | | Update e2fsprogs to 1.45.5 Enable pthreads support Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/gmp: Remove obsolete optionsDaniel Engberg2020-02-181-2/+1
| | | | | | Remove mpbsd argument Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/sed: Update to 4.8Daniel Engberg2020-02-181-3/+5
| | | | | | | | Update sed to 4.8 Use POSIX threads Disable i18n and selinux support Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/patchelf: Update to 0.10Daniel Engberg2020-02-181-2/+2
| | | | | | Update patchelf to 0.10 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/libressl: Update to 3.0.2Daniel Engberg2020-02-182-25/+2
| | | | | | Update libressl to 3.0.2 and remove 010-avoid-glibc.patch as fix is added by upstream Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 05:21:09 +0000