| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased:
bcm27xx/patches-5.10/950-1031-net-lan78xx-Ack-pending-PHY-ints-when-resetting.patch
Removed upstreamed:
mvebu/patches-5.10/101-cpufreq-armada-37xx-forbid-cpufreq-for-1.2-GHz-variant.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
| |
Change `DAP-2965` to `DAP-2695` for device selection in menuconfig.
Fixes: cd09f26660b6 ("ath79: add support for D-Link DAP-2695-A1")
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
The TP-Link TL-MR3020 v3 only has a single MAC address assigned for
ethernet LAN as well as WiFi. This MAC address is also printed on the
casing.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
| |
The GigaDevices GD25Q64B found on the TL-MR3020 v3 supports the fast
read instruction. Add the required DT property in order to enable usage
of this property.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
| |
The GigaDevices GD25Q64B supports higher SPI clocks than 10 MHz. While
100 MHz do not work reliably, 50 MHz works without issues.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
| |
The modec{1,2} keys are actually switches.
Add the respective DTS properties to avoid accidental activation of
failsafe mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
| |
The hostapd.sh script already has support for configuring proxy-ARP,
however no built variant has support for it enabled.
Enable proxy-ARP support for hostapd-full builds in order to allow users
to actually use this feature.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
| |
The disable_dgaf config fiels is only available in case Hostapd is
compiled with Hotspot 2.0 support, however Proxy-ARP does not depend on
Hotspot 2.0.
Only add the code related to this config field when Hotspot 2.0 is
enabled to fix compilation with the aformentioned preconditions.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
| |
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
| |
The uImage.FIT partition uses page mapping without properly handling
paging errors. This can lead to Kernel Oops in case of read errors
while trying to parse uImage.FIT partitions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
| |
this change was missing during the spi-nand driver replacement, causing
build failure.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
|
|
| |
These options doesn't show up unless some kernel packages are selected,
so they are not covered by kernel_menuconfig.
Manually add them so that a build with all kmods can pass without user
interaction.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
| |
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
|
| |
there's no driver level remapping of oob data in the new spi-nand
driver and bmt oob signature starts at 0x0 of the dumped oob data.
change the default value to 0 for the new spi-nand driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
|
|
| |
mtd->size will be overrided by BMT which makes all mtd requests made by
bmt fail in request size checking.
this commit changes the driver to check against actual chip size in chip
info as a workaround.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
| |
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
| |
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
| |
we now have a standalone mtd driver and the old spi-mem driver along
with the hack in spi-nand core can be removed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
| |
This patch enables new spi-nand driver for mt7622 and mt7629.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds a new spi-nand driver which implements the SNFI of mt7622
and mt7629.
Unlike the existing snfi driver which makes use of the spi-mem framework
and the spi-nand framework with modified ecc support, this driver is
implemented directly on the mtd framework with other components untouched,
and provides better performance, and behaves exactly the same as the nand
framework.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This version fixes two vulnerabilities:
- SM2 Decryption Buffer Overflow (CVE-2021-3711)
Severity: High
- Read buffer overruns processing ASN.1 strings (CVE-2021-3712)
Severity: Medium
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
|
|
|
|
|
|
|
| |
this is no longer necessary as the AR71XX target
was superseded by ath79.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This was old code from the AR71XXs target days that
doesn't get compiled and used anymore.
Bringing up AR92xx and earlier chips from their
OWL-Emulator state is currently done by the upstream
ath9k-pci-owl-loader module. (see the kmod-owl-loader
package).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
OpenWrt's special gpio-button-hotplug driver is still using
exclusively the legacy GPIO Subsystem gpio_ API.
While it still does work fine for most devices, upstream
linux is starting to convert platform support like that of
the APU2/3/4 to the new GPIOD LOOKUP tables that are not
supported by it.
Hence, this patch replaces the gpio_ calls present in
gpio-button-hotplug with gpiod_ equivalent wherever
it's possible. This allows the driver to use the
gpiod lookup tables and still have a fallback for
legacy platform data code that just sets button->gpio
set to the real button/switch GPIO.
As a bonus: the active_low logic is now being handled
by the linux's gpio subsystem too. Another issue that
was address is the of_handle leak in the dt parser
error path.
Tested with legacy platform data: x86_64: APU2, MX-100
Tested on OF: ATH79; MR18, APM821xx: Netgear WNDR4700,
RAMIPS: WL-330N3G
LANTIQ: AVM FritzBox 7360v1
Reported-by: Chris Blake <chrisrblake93@gmail.com>
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Onion Omega is a hardware development platform with built-in WiFi.
https://onioniot.github.io/wiki/
Specifications:
- QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor)
- 64MB of DDR2 RAM running at 400 MHz
- 16MB of on-board flash storage
- Support for USB 2.0
- Support for Ethernet at 100 Mbps
- 802.11b/g/n WiFi at 150 Mbps
- 18 digital GPIOs
- A single Serial UART
- Support for SPI
- Support for I2S
Flash instructions:
The device is running OpenWrt upon release using the ar71xx target.
Both a sysupgrade
and uploading the factory image using u-boots web-UI do work fine.
Depending on the ssh client, it might be necessary to enable outdated
KeyExchange methods e.g. in the clients ssh-config:
Host 192.168.1.1
KexAlgorithms +diffie-hellman-group1-sha1
The stock credentials are: root onioneer
For u-boots web-UI manually configure `192.168.1.2/24` on your computer,
connect to `192.168.1.1`.
MAC addresses as verified by OEM firmware:
2G phy0 label
LAN eth0 label - 1
LAN is only available in combination with an optional expansion dock.
Based on vendor acked commit:
commit 5cd49bb067ca ("ar71xx: add support for Onion Omega")
Partly reverts:
commit fc553c7e4c8e ("ath79: drop unused/incomplete dts")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
|
|
|
|
|
|
|
|
|
| |
This integrates with netifd in order to provide STP/RSTP protocol support
in user space. It defaults to using RSTP for bridges with stp enabled.
This daemon has no config files, it uses the configuration passed from
netifd via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
50e6b20 libfstools: handle open() return value properly in F2FS check
e1b6811 blockd: include missing libubox/utils.h
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
| |
This patch has been accepted for linux v5.14.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
| |
Give users more control by exposing ephy leds.
Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Generally u-boot should keep read-only to avoid mis-overwriting and
bricking the device, but u-boot-env could be safely modified with u-boot
setenv tool.
Signed-off-by: David Yang <mmyangfl@gmail.com>
|
|
|
|
|
|
|
| |
The flash is Winbond 25Q128. As it has large rom, better to increase flash
frequency to 70MHz according to the flash spec and enable fast-read.
Signed-off-by: David Yang <mmyangfl@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)
Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/
Installation:
Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update
Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash
Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
- SoC: QCA9558
- DRAM: 128MB DDR2
- Flash: 16MB SPI-NOR
- Wireless: on-board abgn 2×2 2.4GHz radio
- Ethernet: 2x 10/100/1000 Mbps (1x 802.11af PoE)
- miniPCIe slot
Flash instruction:
- From u-boot
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj558-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
boot
- From cpximg loader
The cpximg loader can be started either by holding the reset button
during power up. Once it's running, a TFTP-server under 192.168.1.1 will accept
the image appropriate for the board revision that is etched on the board.
For example, if the board is labelled '6A07':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj558-16m-squashfs-cpximg-6a07.bin
Signed-off-by: Romain Mahoux <romain@mahoux.fr>
[convert to nvmem, remove redundant lan_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
The problem has been fixed in f47cb405cafd ("ipq806x: fix pci broken
on bootm command"), now the pcie part can be written in the usual way.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3
Installation:
* Web UI Update
1. Open http://192.168.10.1/upgrade.html in the browser.
2. Rename firmware to a short name like firmware.bin and then upload it.
3. Fill in the password column with the following content:
password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
1. Connect device with a TTL cable.
2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
3. Upload firmware by tftpd64, it will boot when write instruction is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
* SOC: MT7628AN + MT7612E
* ROM: 8 MiB Flash
* RAM: 64 MiB DDR2
* WAN: 10/100M *1
* LAN: 10/100M *3
* Button: Reset *1
* LEDs: orange *1, white *1
* Antennas: 2.4 GHz *2 + 5 GHz *2
* TTL Baudrate: 57600
* TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100
MAC addresses as verified by OEM firmware:
use address source
2g *:d8 factory 0x0004 (label)
5g *:d9 factory 0x8004
LAN *:d7 factory $label -1
WAN *:da factory $label +2
Installation (TFTP + U-Boot):
* Connect device with a TTL cable and open a serial session by
PuTTY.
* Press "2" when booting to select "Load system code then write
to Flash via TFTP".
* Configure the IP of local host server.
* Upload firmware by tftpd64, it will boot when write instruction
is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix DTS line endings, fix label MAC address, adjust status LED
names, convert mtd-mac-address-increment to mac-address-increment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
The partition name in the device dts is '0:ART'.
Be independent to prevent this part from becoming
incorrect once the kernel v5.4 gone.
Fixes: da8428d277cd ("ipq806x: add support for Askey RT4230W REV6")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Descriptions:
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.
OpenWrt selection table:
official firmware version OpenWrt
v22.4.x.x or older phicomm_k2-v22.4
v22.5.x.x or newer phicomm_k2-v22.5
Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
words "K2 telnet"), and then we can upload firmware image to
/tmp and write it to firmware partition with mtd instruction.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
The setup is the same for all devices, so move it up one level.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
8a8306d uxc.c: fix coverity resource leak warning
7f2398e jail: devices: create parent folder when creating devices
0603c8d jail: return to hook callback instead of just calling it
3edb7eb jail: check return value when opening console
af048a3 jail: use portable sizeof(void *)
6010bd3 utils: make sure read() string is 0 terminated
f6daca3 uxc: free string returned by blobmsg_format_json_indent()
51f1cd2 trace: free string returned by blobmsg_format_json_indent()
d716cb5 trace: handle open() return value and make sure string is terminated
b824a89 jail: preload: avoid NULL-dereference in case things go wrong
167dc24 jail: protect against strcat buffer overflows
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
| |
94170ae24bc9 device: extend device settings flags to 64 bit
1eb0fafaa986 device: add support for configuring device link speed/duplex
ed84473b7af9 bridge: memset bst->config by default to avoid stale config values
6519cf31e4b0 bridge: add support for an external STP daemon
454e9c33c906 bridge: tune default stp parameters
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
d716ac4bc423 list.h: add a few missing iterator macros
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
The channel offset used for VHT segment calculation was missing for HT
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
| |
Add a config option for json_script instead of unconditionally including
all json files in /etc/uhttpd in every uhttpd instance. This makes it
possible to configure a single instance with an unconditional redirect,
which currently renders all other uhttpd instances unusable.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
01b4e60 dhcpv4: fix uninitialized hostname in some ubus events
1666769 dhcpv6-ia: allow up to 64 bit wide hostid
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
The option was initially named TARGET_ROOTFS_LN_VAR_TMP, and the check
was correct. When renaming the option to something more suitable, the
check was changed to check for n, but when an option is not set, it's
not n but empty. This results in the check always evaluating to false.
Fix the check by checking for y with ifneq.
Fixes: 57807f50ded6 ("base-files: add option to make /var persistent")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Atheros DB120 reference board.
Specifications:
SoC: QCA9344
DRAM: 128Mb DDR2
Flash: 8Mb SPI-NOR, 128Mb NAND flash
Switch: 5x 10/100Mbps via AR8229 switch (integrated into SoC),
5x 10/100/1000Mbps via QCA8237 via RGMII
WLAN: AR9300 (SoC, 2.4G+5G) + AR9340 (PCIe, 5G-only)
USB: 1x 2.0
UART: standard QCA UART header
JTAG: yes
Button: 1x reset
LEDs: a lot
Slots: 2x mPCIe + 1x mini-PCI, but using them requires
additional undocumented changes.
Misc: The board allows to boot off NAND, and there is
I2S audio support as well - also requiring
additional undocumented changes.
Installation:
1. Original bootloader
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
available via TFTP
tftpboot 0x80060000 openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
2. pepe2k's u-boot_mod
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
available via TFTP, as "firmware.bin"
run fw_upg
Reboot the board.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[explicit factory recipe in generic.mk, sorting in 10-ath9k-eeprom,
convert to nvmem, use fwconcat* names in DTS, remove unneeded DT
labels, remove redundant uart node]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|