| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
| |
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Setting this options modifies the rootfs size of created images. When
installing a large number of packages it may become necessary to
increase the size to have enough storage.
This option is only useful for supported devices, i.e. with an attached
SD Card or installed on a hard drive.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 7b7edd25a571568438c886529d3443054e02f55f)
|
|
|
|
|
|
|
|
|
|
| |
Prevent the BBT translation layer from remapping the UBI used for
storing rootfs.
Explicitly define the number of blocks reserved for remapping.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 076da59f17803e9412ef5e50988aff6c7e536292)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The DAP-X1860 is a wall-plug AX1800 repeater.
Specifications:
- MT7621, 256 MiB RAM, 128 MiB SPI NAND
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- Ethernet: 1 port 10/100/1000
- LED RSSI bargraph (2x green, 1x red/orange), status
and RSSI LEDs are incorrectly populated red/orange
(should be red/green according to documentation)
Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
- Upload factory.bin, confirm flashing
(seems to work best with Chromium-based browsers)
Revert to OEM firmware:
- tar -xvf DAP-X1860_RevA_Firmware_101b94.bin
- openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \
-out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ==
- tar -xvf FWImage.st1
- flash kernel_DAP-X1860.bin via Recovery
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
(cherry picked from commit 3c31f6b521bb5fc49e222a8f2bcd454b73452a0e)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix flash I/O instability observed in newer devices with cFeon
QH64A-104HIP (detected as en25qh64).
Ref: https://forum.openwrt.org/t/support-for-tp-link-re305-v3/75893/91
Reported-by: Dimitri Souza <dimitri.souza@gmail.com>
Tested-by: Dimitri Souza <dimitri.souza@gmail.com>
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[alter commit-message - target master]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2122c80b321d439cf8b669ae26fcfeec605cf2cc)
|
|
|
|
|
|
|
|
| |
Fixes Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 561
Fixes: #11701 for both 3500(B)
Signed-off-by: Maik Goette <github@beeit.de>
(cherry picked from commit 4d9c38d654fdfb72ef641573bbf5b0f73f638f2e)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds libbpf to the dependencies of tc-mod-iptables.
The package tc-mod-iptables is missing libbpf as a dependency,
which leads to the build failure described in bug #9491
LIBBPF_FORCE=on set, but couldn't find a usable libbpf
The build dependency is already automatically added because some other
packages from iproute2 depend on libbpf, but bpftools has multiple build
variants. With multiple build variants none gets build by default and
the build system will not build bpftools before iproute2.
Fixes: #9491
Signed-off-by: Kien Truong <duckientruong@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit fa468d4bcdc7e6eb84ea51d9b05368ed87c43aae)
|
|
|
|
|
|
|
|
|
|
|
| |
22.03.1+ and snapshot builds no longer fit the 6M flash space
available for these models.
This disables failing buildbot image builds for these devices.
Images can still be built manually with ImageBuilder.
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
(cherry picked from commit 4965cbd259bb9001e8724f53520f4be1e4723212)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.
Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
(cherry picked from commit 7ea965b57803ceec20222279377e611652ac217f)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix the trivial abscence of $() when assigning engine config files to
the main libopenssl-config package even if the corresponding engines
were not built into the main library.
This is mostly cosmetic, since scripts/ipkg-build tests the file's
presence before it is actually included in the package's conffiles.
Fixes: 30b0351039 "openssl: configure engine packages during install"
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit c75cd5f6028da6ceb1fb3438da93e2305cd720b1)
|
|
|
|
|
|
|
|
|
|
| |
Some vendors of Senao boards have put a bootloader
that cannot handle both large gzip or large lzma files.
There is no disadvantage by doing this for all of them.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 8342c092a03caedbf160d4ac3982c6a9be91261f)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
glinet forum users reported the problem at
https://forum.gl-inet.com/t/gl-ar300m16-openwrt-22-03-0-rc5-usb-port-power-off-by-default/23199
The current code uses the regulator framework to control the USB power
supply. Although usb0 described in DTS refers to the regulator by
vbus-supply, but there is no code related to regulator implemented
in the USB driver of QCA953X, so the USB of the device cannot work.
Under the regulator framework, adding the regulator-always-on attribute
fixes this problem, but it means that USB power will not be able to be
turned off. Since we need to control the USB power supply in user space,
I didn't find any other better way under the regulator framework of Linux,
so I directly export gpio.
Signed-off-by: Luo Chongjun <luochongjun@gl-inet.com>
(cherry picked from commit b352124cd2115fec648a00956a848660df9477d3)
|
|
|
|
|
|
|
|
|
|
| |
Fix DT_DEBUG handling on MIPS in musl libc.
With this change gdb will load the symbol files for shared libraries on MIPS too.
This patch was taken from this thread: https://www.openwall.com/lists/musl/2022/01/09/4
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
(cherry picked from commit fcdd407e8e16b90e1995789ba217be5591a88d2f)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Changes:
7f7a9f7 wireless-regdb: update regulatory database based on preceding changes
660a1ae wireless-regdb: Update regulatory info for Russia (RU) on 5GHz
fe05cc9 wireless-regdb: Update regulatory rules for Japan (JP) on 6GHz
d8584dc wireless-regdb: Update regulatory rules for Japan (JP) on 5GHz
c04fd9b wireless-regdb: update regulatory rules for Switzerland (CH)
f29772a wireless-regdb: Update regulatory rules for Brazil (BR)
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
(cherry picked from commit 1173edf23b3440137d60162d1ef9f48ffa13e3e2)
|
|
|
|
|
|
|
|
|
| |
Sourcing of image/Config.in will not happen
When a target is installed from target/linux/feeds/
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 522a60cd31686a3d1b6d7ed1229eb68568aa89ac)
|
|
|
|
|
|
|
|
| |
Fixes the boot loader LZMA decompression issue:
LZMA ERROR 1 - must RESET board to recover
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
(cherry picked from commit 84c04ff4069a652755267d126418b211379c1cbf)
|
|
|
|
|
|
|
|
| |
This removes the non-selectable 'Kernel' item
when make menuconfig.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 3e4c014008659c760b2e4638f606da90df1e3c93)
|
|
|
|
|
|
|
|
|
|
| |
Some packages offer functionalities guarded by these options and it'll
be impossible to reach them without changing Config-build.in. So allow
to toggle these in more friendly way, by exposing them in configuration
menu.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit 477ff0821a5e532adc0861d4093029967f5e1178)
|
|
|
|
|
|
|
|
|
| |
Remove upstreamed patches.
Switch to normal tarballs. Codeload recently had a reproducibility issue.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 44c24b3ac5d4523c0f9f55691d28387508e93de5)
|
|
|
|
|
|
|
| |
Fixes bogus errors on ubus calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit cf992ca862f271936f61367236378378f0d91b6d)
|
|
|
|
|
|
|
|
|
| |
Pahole version is being autodetected during runtime since kernel 5.15.96
via in-kernel scripts/pahole-version.sh so add CONFIG_PAHOLE_VERSION to
kernel filter in order to prevent it from being added to target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5d8f14bfefc6f12e93425ee522bdce75a7c979d6)
|
|
|
|
|
|
|
|
| |
The dhcphostsfile must be mounted into the (ujail) sandbox.
The file can not be accessed without this mount.
Signed-off-by: Ruben Jenster <rjenster@gmail.com>
(cherry picked from commit 936df715de3d33947ce38ca232b05c2bd3ef58f1)
|
|
|
|
|
|
|
|
| |
ipaddr option can be in CIDR notation,
but udhcp wants just an IP address
Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
(cherry picked from commit 506bb436c678779e8ee54e83a7fb3e4e880037ec)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The nand driver normally while waiting for the device to become ready;
this is normally fine, but xway_nand holds the ebu_lock spinlock, and
this can cause lockups if other threads which use ebu_lock are
interleaved. Fix this by waiting instead of polling.
This mainly showed up as crashes in ath9k_pci_owl_loader (see
https://github.com/openwrt/openwrt/issues/9829 ), but turning on
spinlock debugging shows this happening in other places too.
This doesn't seem to measurably impact boot time.
Tested on bt_homehub-v5a with 5.10 and 5.15.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[Add commit description into patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d3b47909b199b876f67a0387b5545cb73bd6b815)
|
|
|
|
|
|
|
|
|
| |
Potentially fixes some driver data structure corruption issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9779ee021d30508eb9e7ebf1ec0a28a4be3c4c19)
[Change patch number]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Nests kernel and ubi into firmware partition in-order to be compatible
with OEM firmware. This allows restoring oem firmware from a backup of
firmware2. Add jffs2 partition which is present in the oem firmware.
Add support for mediatek NMBM (wear leveling on newer mediatek devices).
Exclude UBI partition from NMBM management.
Continues PR #10685.
Tested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit 787ecdf66de6798540fb8b756404566341b4733c)
|
|
|
|
|
|
|
|
|
| |
The Asus RT-AX1800U is identical to the already supported Asus RT-AX53U.
Use the ALT0 buildroot tags to show both devices.
Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit acd3b5e83b99879b326a940907a9ff334586f86b)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the missing LEDs to Asus RT-AX53U.
Based on PR #10400 and patch provided in #11068
- enable the two LEDs controlled by mt7915e for wireless;
- add label to power LED so it works properly and fix formatting;
- add the USB LED;
- switch LEDs are best left to be controlled by hardware for now.
Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com>
Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Co-Authored-By: Hartmut Birr <e9hack@gmail.com>
Tested-by: Felix Baumann <felix.bau@gmx.de>
Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Marian Sarcinschi <znevna@gmail.com>
(cherry picked from commit c4b806d5c4ccc653968620e6e9aec93bc4e370e5)
|
|
|
|
|
|
|
|
|
|
| |
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition
can be correctly read.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 75451681d03e609ac8a3d1cd7469eefa53e18ca4)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for read/writing uboot env by renaming the second partition
to its stock label "nvram" and remove the deemed unnecessary
"read-only". Split the first partition "u-boot" in two, in order
to allow `fw_setenv` safe write-access to the uboot environment
variables.
This implements hauke's request from [1].
Based on the patch provided by Shiji Yang.
[1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224
Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description, fix some whitespace problem ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3f1e9f6f3b14385cab7ca6d1dcc2a4b658475bc3)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Mikrotik R11e-LTE6 modem is similar to ZTE MF286R modem, added
earlier: it has a Marvel chip, able to work in ACM+RNDIS mode, knows ZTE
specific commands, runs OpenWrt Barrier Breaker fork.
While the modem is able to offer IPv6 address, the RNDIS setup is unable
to complete if there is an IPv6 adress.
While it works in ACM+RNDIS mode, the user experience isn't as good as
with "proto 3g": the modem happily serves a local IP (192.168.1.xxx)
without internet access. Of course, if the modem has enough time
(for example at the second dialup), it will serve a public IP.
Modifing the DHCP Lease (to a short interval before connect and back to
default while finalizing) is a workaround to get a public IP at the
first try.
A safe workaround for this is to excercise an offline script of the
pingcheck program: simply restart (ifdown - ifup) the connection.
Another pitfall is that the modem writes a few messages at startup,
which confuses the manufacturer detection algorithm and got disabled.
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (2366): Failed to parse message data
daemon.notice netifd: mikrotik (2366): WARNING: Variable 'ok' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2366): Unsupported modem
daemon.notice netifd: mikrotik (2426): Stopping network mikrotik
daemon.notice netifd: mikrotik (2426): Failed to parse message data
daemon.notice netifd: mikrotik (2426): WARNING: Variable '*simdetec:1,sim' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2426): Unsupported modem
daemon.notice netifd: Interface 'mikrotik' is now down
A workaround for this is to use the "delay" option in the interface
configuration.
I want to thank Forum members dchard (in topic Adding support for
MikroTik hAP ac3 LTE6 kit (D53GR_5HacD2HnD)) [1]
and mrhaav (in topic OpenWrt X86_64 + Mikrotik R11e-LTE6) [2]
for sharing their experiments and works.
Another information page was found at eko.one.pl [3].
[1]: https://forum.openwrt.org/t/137555
[2]: https://forum.openwrt.org/t/151743
[3]: https://eko.one.pl/?p=modem-r11elte
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit dbd6ebd6d84b35599a0446559576df41f487200e)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The MikroTik R11e-LTE6 modem goes into flight mode (CFUN=4) at startup
and the radio is off (*RADIOPOWER: 0):
AT+RESET
OK
OK
*SIMDETEC:2,NOS
*SIMDETEC:1,SIM
*ICCID: 8936500119010596302
*EUICC: 1
+MSTK: 11, D025....74F3
*ADMINDATA: 0, 2, 0
+CPIN: READY
*EUICC: 1
*ECCLIST: 5, 0, 112, 0, 000, 0, 08, 0, 118, 0, 911
+CREG: 0
$CREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
+CGREG: 0
+CEREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
*RADIOPOWER: 0
+MMSG: 0, 0
+MMSG: 0, 0
+MMSG: 1, 0
+MPBK: 1
While the chat script is able to establish the PPP connection,
it's closed instantly by the modem: LCP terminated by peer.
local2.info chat[7000]: send (ATD*99***1#^M)
local2.info chat[7000]: expect (CONNECT)
local2.info chat[7000]: ^M
local2.info chat[7000]: ATD*99***1#^M^M
local2.info chat[7000]: CONNECT
local2.info chat[7000]: -- got it
local2.info chat[7000]: send ( ^M)
daemon.info pppd[6997]: Serial connection established.
kern.info kernel: [ 453.659146] 3g-mikrotik: renamed from ppp0
daemon.info pppd[6997]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[6997]: Using interface 3g-mikrotik
daemon.notice pppd[6997]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.info pppd[6997]: LCP terminated by peer
daemon.notice pppd[6997]: Connection terminated.
daemon.notice pppd[6997]: Modem hangup
daemon.info pppd[6997]: Exit.
daemon.notice netifd: Interface 'mikrotik' is now down
Sending "AT+CFUN=1" to modem deactivates the flight mode and
solves the issue:
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (7051): sending -> AT+CFUN=1
daemon.notice pppd[7137]: pppd 2.4.9 started by root, uid 0
local2.info chat[7140]: abort on (BUSY)
local2.info chat[7140]: abort on (NO CARRIER)
local2.info chat[7140]: abort on (ERROR)
local2.info chat[7140]: report (CONNECT)
local2.info chat[7140]: timeout set to 10 seconds
local2.info chat[7140]: send (AT&F^M)
local2.info chat[7140]: expect (OK)
local2.info chat[7140]: ^M
local2.info chat[7140]: +CESQ: 99,99,255,255,255,255^M
local2.info chat[7140]: ^M
local2.info chat[7140]: *CESQ: 99,99,255,255,255,255,0^M
local2.info chat[7140]: AT&F^MAT&F^M^M
local2.info chat[7140]: OK
local2.info chat[7140]: -- got it
...
local2.info chat[7140]: send (ATD*99***1#^M)
local2.info chat[7140]: expect (CONNECT)
local2.info chat[7140]: ^M
local2.info chat[7140]: ATD*99***1#^M^M
local2.info chat[7140]: CONNECT
local2.info chat[7140]: -- got it
local2.info chat[7140]: send ( ^M)
daemon.info pppd[7137]: Serial connection established.
kern.info kernel: [ 463.094254] 3g-mikrotik: renamed from ppp0
daemon.info pppd[7137]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[7137]: Using interface 3g-mikrotik
daemon.notice pppd[7137]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.warn pppd[7137]: Could not determine remote IP address: defaulting to 10.64.64.64
daemon.notice pppd[7137]: local IP address 100.112.63.62
daemon.notice pppd[7137]: remote IP address 10.64.64.64
daemon.notice pppd[7137]: primary DNS address 185.29.83.64
daemon.notice pppd[7137]: secondary DNS address 185.62.131.64
daemon.notice netifd: Network device '3g-mikrotik' link is up
daemon.notice netifd: Interface 'mikrotik' is now up
To send this AT command to the modem the "runcommand.gcom" script
dependency is moved from comgt-ncm to comgt.
As the comgt-ncm package depends on comgt already, this change
is a NOOP from that point of view.
But from the modem's point it is a low hanging fruit as the modem
is usable with installing comgt and kmod-usb-ncm packages.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit 91eca7b04ff1309c7408baa1f1631d7623ce50cf)
|
|
|
|
|
|
|
|
| |
The XMC XM25QH64C is a 8MB SPI NOR chip. The patch is verified on TL-WPA8631P v3.
Datasheet available at https://www.xmcwh.com/uploads/442/XM25QH64C.pdf
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
(cherry picked from commit 19752bdfa3e75da8290f525186e9fd8349df9c93)
|
|
|
|
|
|
|
| |
Refresh the kernel patches.
Fixes: c2331038b257 ("kernel: remove obsolete netfilter tcp window size check bypass patch")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
| |
On any currently supported hardware, the performance impact should not
matter anymore.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 75e78bcaab847557ce1782eb2dea9dff9a029171)
|
|
|
|
|
|
|
| |
Fixes CVE-2022-47522
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit d54c91bd9ab3c54ee06923eafbd67047816a37e4)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch solves the problem of receiving "error" responses when
initially calling gcom. This avoids unnecessary NO_DEVICE failures.
A retry loop retries the call after an "error" response within the
specified delay. A successful response will continue with the connection
immediately without waiting for max specified delay, bringing the
interface up sooner.
Signed-off-by: Mike Wilson <mikewse@hotmail.com>
(cherry picked from commit 8f27093ce784daad5a9b1c89f51d0a76a8bbb07b)
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit f598880162e83ddc0139e00c5248497d06f5fff7)
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased:
backport-5.10/611-v5.12-net-ethernet-mediatek-support-setting-MTU.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 3ca98495897126113912f7ee4537f69459d21332)
|
|
|
|
|
|
|
| |
No patches needed to be rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 72d9d2b923b389f09e2ba43f4aba22c068e6cbb7)
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased:
ramips/patches-5.10/810-uvc-add-iPassion-iP2970-support.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit d4aad642ff80750ec16a58058eb6da718e2129cd)
|
|
|
|
|
|
|
| |
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/net/sched?h=v5.10.173&id=18c3fa7a7fdbb4d21dafc8a7710ae2c1680930f6
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit fbfec3286e8bfce3a78749b7bcb67e658665f197)
|
|
|
|
|
|
|
|
|
|
|
|
| |
We use late loading[1] so need to set this option despite upstream adding a
kernel taint when this option is set. See discussion in PR#12149 for more details.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v5.10.173&id2=v5.10.172
1. https://github.com/openwrt/openwrt/blob/master/target/linux/x86/base-files/lib/preinit/02_load_x86_ucode
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 0c5ffe1ab2b4843635555e2a234f8bd5cb4d6978)
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed:
backport-5.10/804-0001-net-Remove-WARN_ON_ONCE-sk-sk_forward_alloc-from-sk_.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.171&id=3e4bbd1f38a8d35bd2d3aaffdb5f6ada546b669a
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 50cb897d251133752ea2cd338153a6dcb011ea98)
|
|
|
|
|
|
|
| |
No patches modified for this bump
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit a14cc979a2a081c31763b994219ae0d0ddebd9f2)
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add fix:
target/linux/generic/backport-5.10/804-0001-net-Remove-WARN_ON_ONCE-sk-sk_forward_alloc-from-sk_.patch[3]
All other patches automatically rebased.
3. https://lore.kernel.org/stable/20230227211548.13923-1-kuniyu@amazon.com
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit b88955aa2294c61f21bdf7014e10d8ea29d0c346)
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit cb2661844a5d54d44230ee564d4f17605a794a49)
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit ffaabee9b8d9da7c15a50f52897ae5f70b40b4e7)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The USB port on the MR8300 randomly fails to feed bus-powered devices.
This is caused by a misconfigured pinmux. The GPIO68 should be used to
enable the USB power (active low), but it's inside the NAND pinmux.
This GPIO pin was found in the original firmware at a startup script in
both MR8300 and EA8300. Therefore apply the fix for both boards.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ed64c3323590e3c9fa8b423bf37689023a7a101f)
Signed-off-by: Steffen Scheib <steffen@scheib.me>
|
|
|
|
|
|
|
|
|
|
| |
Fixes boot loader LZMA decompression issues (LZMA ERROR 1)
As reported in issue #12208
Reported-by: Raúl M. <raul.m@sparkedhost.com>
Tested-by: Raúl M. <raul.m@sparkedhost.com>
Signed-off-by: Tony Butler <spudz76@gmail.com>
(cherry picked from commit 889bbf89bb679f0c5b0fa432e27a3e0dd8940a4e)
|