aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-194-0/+199
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com> (cherry picked from commit 78c3534645958c123aa82cec9926a34eed5dd5dd)
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-193-1/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit bb505d82add5636da891bb97fdabc57947280e88)
* Revert "kernel: backport MT7530 VLAN fix"Stijn Tintel2022-04-195-523/+0
| | | | | | | | | | | There are various reports on Github and in the forum that this commit causes multiple problems. This reverts commit ee6ba216d8ba1b02154c287e64d709a8bc7b0054. Fixes: #9420 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit 3e0daca6447c3d5b9eb6d24ecb8e52f256f385cc)
* ath79: add support for MikroTik RouterBOARD wAP-2nD (wAP)David Musil2022-04-185-1/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik RouterBOARD wAP-2nd (sold as wAP) is a small 2.4 GHz 802.11b/g/n PoE-capable AP. Specifications: - SoC: Qualcomm Atheros QCA9533 - Flash: 16 MB (SPI) - RAM: 64 MB - Ethernet: 1x 10/100 Mbps (PoE in) - WiFi: AR9531 2T2R 2.4 GHz (SoC) - 3x green LEDs (1x lan, 1x wlan, 1x user) See https://mikrotik.com/product/RBwAP2nD for more info. Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Note: following 781d4bfb397cdd12ee0151eb66c577f470e3377d The network setup avoids using the integrated switch and connects the single Ethernet port directly. This way, link speed (10/100 Mbps) is properly reported by eth0. Signed-off-by: David Musil <0x444d@protonmail.com> (cherry picked from commit e20de224427008e0f26161f924bc347d974fd15a)
* mac80211: fix QCA9561 PA biasThibaut VARÈNE2022-04-181-0/+47
| | | | | | | | | | | | | | | This patch fixes an invalid TX PA DC bias level on QCA9561, which results in a very low output power and very low throughput as devices are further away from the AP (compared to other 2.4GHz APs), following a suggestion from nbd[1]. This patch has been submitted upstream[2]. [1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name [2] https://lore.kernel.org/linux-wireless/20220417145145.1847-1-hacks+kernel@slashdirt.org/ Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit 7dc52a78ae2c2f748a0c0c4adcb13979260b3498)
* mpc85xx: move Extreme WS-AP3825i GPIO extenderDavid Bauer2022-04-181-23/+25
| | | | | | | | Move the GPIO extender to the SoC node. Otherwise, the legacy PowerPC init code will not populate the BUS and thus never probe spi-gpio. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f0c09d0305835abc7bcc32285dc82c008159936d)
* kernel: Remove patch for kernel 5.15Hauke Mehrtens2022-04-171-48/+0
| | | | | | | | This patch was accidentally backported from master for kernel 5.15 too. Remove the version for kernel 5.15 and keep the version for kernel 5.10. Fixes: 9ab337dfbce7 ("kernel: backport pgalloc memory leak fix") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* readline: add host PICRosen Penev2022-04-171-0/+1
| | | | | | | | Python seems to fail to link to libreadline properly because of this. Not a fatal error but an error nontheless. Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit b363f7488643882b9c53a1e2c6db2a110703cc1d)
* kernel: bump 5.10 to 5.10.111John Audia2022-04-1724-179/+42
| | | | | | | | | | | | | | | Removed upstreamed: pending-5.10/850-0003-PCI-aardvark-Fix-support-for-MSI-interrupts.patch apm821xx/patches-5.10/150-ata-sata_dwc_460ex-Fix-crash-due-to-OOB-write.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us> (cherry picked from commit 0085dd6cb5e3c57dd22994c22ce893575711b6f7)
* linux-firmware: Update to version 20220411Hauke Mehrtens2022-04-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following files used in OpenWrt changed: amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam17h.bin amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam19h.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_smc.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sos.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_ta.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/arcturus_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ce.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_me.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_smc.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sos.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ta.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_ce.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_me.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/dcn_3_1_6_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ce.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_me.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_smc.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sos.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ta.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_ce.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_me.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_asd.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ce.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_me.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ta.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_asd.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_ce.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_me.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_mec.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_asd.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma1.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_asd.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_smc.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ce.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_me.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_smc.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_asd.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_ce.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_me.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_mec.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_ta.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_asd.bin amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_ta.bin amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_toc.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_asd.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_ce.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_me.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_mec.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_ta.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/raven_asd.bin amdgpu-firmware/lib/firmware/amdgpu/raven_ce.bin amdgpu-firmware/lib/firmware/amdgpu/raven_me.bin amdgpu-firmware/lib/firmware/amdgpu/raven_mec.bin amdgpu-firmware/lib/firmware/amdgpu/raven_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/raven_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/raven_ta.bin amdgpu-firmware/lib/firmware/amdgpu/raven_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_asd.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_ce.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_me.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_mec.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_ta.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/sdma_5_2_7.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ce.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_me.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_smc.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sos.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ta.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_me.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_me.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_me.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_me.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_asd.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ce.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_me.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ta.bin ibt-firmware/lib/firmware/intel/ibt-hw-37.8.10-fw-22.50.19.14.f.bseq iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 54d9051c5596814293edd9e6a534c8d1e56e6fcf)
* lantiq: fritz736x: Move GPIO resets to the inidvidual board.dts filesMartin Blumenstingl2022-04-174-32/+77
| | | | | | | | | | | FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0) and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362 SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the GPIO reset definitions to each individual board .dts and while at it, fix the GPIOs for the FRITZ!Box 7362 SL. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> (cherry picked from commit 56cd49bdc8ff762c52327ee7faa14cb99895e0fd)
* comgt: support ZTE MF286R modemCezary Jackiewicz2022-04-172-1/+23
| | | | | | | | | | | | | The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to establish connection with custom commands specific to ZTE modems. Two variants of modems were discovered, some identifying themselves as "ZTE", and others as plain "Marvell", the chipset manufacturer. The modem itself runs a fork of OpenWrt inside, which root shell can be accessed via ADB interface. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit e02fb42c53bad5dd36726c6ef5a46bfe31d2e400)
* comgt: ncm: try to detect interface for ttyACM portsLech Perczak2022-04-171-0/+4
| | | | | | | | | | | | Some modems expose ttyACM as their control ports, which have the "device" symlink pointing one level down in sysfs tree. Try to find network interfaces for them as well, this is commonly used for modems exposing ACM + RNDIS or ACM + ECM interface combinations. Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit ed7957810c0aee04943559be9b0ed23431ee0654)
* comgt: ncm: select first available network interface for deviceLech Perczak2022-04-171-3/+4
| | | | | | | | | | | | | | Some modems expose multiple network interfaces on the same USB device, causing the connection setup script to fail, because glob matching in the detection phase causes 'ls' to output more than one interface name plus their base directories in sysfs. Avoid that by listing the directories explicitly and then selecting first available interface. This is the case for some variants of ZTE MF286R built-in modem, which exposes both RNDIS and CDC-ECM network interfaces, causing the connection setup to fail. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit b2940bb8b2878ce193f2edaee3e7d4c44f4a2065)
* comgt: ncm: allow specification of interface nameLech Perczak2022-04-171-14/+18
| | | | | | | | | | | | | Add ifname property to UCI, which can be used to override the autodetected interface name in case the detection fails due to having none or more than one interface exposed by the modem, which is not explicitly linked to TTY port. This is needed on certain variants of ZTE MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces on the modem, on which the automatic detection may select the wrong network interface. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit a67629bbe25ef3d0e159db1e0c6ca81affd06898)
* kernel: backport ZTE RNDIS bogus MAC address fixLech Perczak2022-04-173-0/+239
| | | | | | | | | | | | This is required to support built-in modem of ZTE MF286R, in addition to other external modems, such as MF831, MF910, MF920, which refuse to reconfigure their remote MAC address, even if "locally administered" bit is set, leading to dropped traffic towards the host. Add a workaround for that issue already present in cdc_ether to rndis_host driver as well. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit c99013e242682a71051619806f9cc4f4e51a58fa)
* ipq806x: fix wrong CPU OPP for ipq8062Ansuel Smith2022-04-171-16/+16
| | | | | | | | | | Fix wrong CPU OPP for ipq8062. Revision of the SoC added an extra 25mV for every pvs. Also fix the voltage min/max value that were wrong. Reviewed-by: Robert Marko robimarko@gmail.com Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> (cherry picked from commit 3f0d87fd69b13f7d1fa06bdcc951a2896a0a9360)
* ipq806x: fix USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-171-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The existing device tree has incorrect definitions for usb3_0 and usb3_1 and the blocks they depend upon: their addresses and interrupts are swapped. However, their clocks and resets are not. The result is that the USB blocks are non-functional if only one of them is enabled. This fix backports the definitions from mainline Linux 5.15 to OpenWrt's 5.10 dtsi additions. See the relevant mainline code here: https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148 This fix does not break existing ports. But some ports may have enabled both USB blocks even thought their board only implements one, because enabling a single USB block would not have worked before this fix. This means that revisiting all ports of ipq806x devices that implement a single USB port is advised. This work must be done by maintainers that can determine which USB block corresponds to the implemented port on their hardware. Note that this fix swaps the names of the hardware ports. This is unfortunate, but will happen anyway when switching to kernel 5.15. Thus, it is best to do this ASAP, before users get to depend on port names. It is strongly recommended that this fix is backported to 22.03 before its release. This will minimize the number of users affected by the port name swap. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> (cherry picked from commit 284f2c2ae0e569660effa61c9f8d0f6459a2ae19)
* ipq806x: remove non-working fixes for USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-172-4/+0
| | | | | | | These workarrounds are incomplete and non-functional, and thus not needed. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> (cherry picked from commit 3a4d972d43987e1ab0f697817c0f68d1a4a706dc)
* build: target: improve UX of CONFIG_TARGET handlingPetr Štetiar2022-04-171-7/+15
| | | | | | | | | | | | | | | | | | | | | Make it clear, that for `make kernel_{menu,old}config` it's possible to use only following values for CONFIG_TARGET variable: * env * target * subtarget * subtarget_target This should prevent misuse like `make kernel_menuconfig CONFIG_TARGET=bcm2710` etc. Keep support for obsolete `platform` and `subtarget_platform` targets with deprecation notice so this compat stuff could be removed in the future. Signed-off-by: Petr Štetiar <ynezz@true.cz> Acked-by: Piotr Dymacz <pepe2k@gmail.com> (cherry picked from commit 68e672f32df3d6b8a75534df5962ac99b693601b)
* hostapd: add ubus link-measurements notificationsDavid Bauer2022-04-173-0/+43
| | | | | | | Notify external ubus subscribers of received link-measurement reports. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f6445cfa1acb32676723c49da3e3158b64a4b3d2)
* hostapd: add ubus method for requesting link measurementsDavid Bauer2022-04-171-0/+65
| | | | | | | | | | | Add a ubus method to request link-measurements from connected STAs. In addition to the STAs address, the used and maximum transmit power can be provided by the external process for the link-measurement. If they are not provided, 0 is used as the default value. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 965aa33a18c76bb2d5a1eeb0cfa01501b08e784a)
* hostapd: add support for enabling link measurementsDavid Bauer2022-04-171-0/+10
| | | | | | | | Allow external processes to enable advertisement of link-measurement RRM capability. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 2ca5c3da04c3f05a7477ae484768e03d4ca30711)
* mpc85xx: overhaul WS-AP3825i LED setupDavid Bauer2022-04-172-12/+31
| | | | | | | | | | | | | As the LED controller is working now, we can make good use of the LEDs now. - Drop the model-name prefix - Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such on the casing - Enable wired LEDs in userspace Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 9024f1e466f5ab64bc752d8a463d1867a2ba8d8e)
* image: strip metadata from images when used in other artifactsDaniel Golle2022-04-151-3/+11
| | | | | | | | | | Image metadata and signature is of no use for images which are included inside other artifacts (like an SD-card image). Strip them off before using images in artifacts or stashing them for the ImageBuilder as the contained signature breaks reproducibility. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 7a256d97d9ded84d1bfd531e775099774e7b6b06)
* mtools: update to version 4.0.39Daniel Golle2022-04-151-2/+2
| | | | | | | | | | Improvements since the 4.0.38 release are: - Rename strtoi to strosi (string to signed int). The strtoi function on BSD does something else (returns an intmax, not an int) Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 08ebc3881d3f351d2d4ca9202ca446c96b38a1e1)
* scripts/gen_image_generic.sh: fix order of files in EFI bootfsDaniel Golle2022-04-151-2/+19
| | | | | | | | | | | | | mtools recursive copy (mcopy -s ...) is using READDIR(3) to iterate over the directory entries, hence they end up in the FAT filesystem in traversal order which breaks reproducibility (rather than being added to the FAT filesystem in a reproducible order). Implement recursive copy in gen_image_generic.sh in Shell code instead, as in that way we can force files to be copied in reproducible order. Fixes: aece8f5ae8 ("scripts/gen_image_generic.sh: generate reproducible EFI filesystem") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 4d289ae7e63893f90957b77962c6b60574d35441)
* netifd: relax check in dhcp proto handlerDaniel Golle2022-04-151-1/+1
| | | | | | | | | | Checking whether /sbin/udhcpc is a symbolic link breaks using the DHCP proto handler inside procd-ujail where bind-mounts are used for the resolved link. Check whether /sbin/udhcpc is executable instead to allow using the proto handler for DHCP-provisioned containers. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit c5f113c43f43c20555298c8500bf91bffbe1f58b)
* procd: update to git HEADDaniel Golle2022-04-151-3/+3
| | | | | | | | | 6343c3a procd: completely remove tmp-on-zram support 5c5e63f uxc: fix potential NULL-pointer dereference eb03f03 jail: include necessary files for per-netns netifd instance Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 2c8873033e3c0b5a5e8f6080ea3a73fde6a55f39)
* base-files: more robust sysupgrade on NANDDaniel Golle2022-04-151-4/+10
| | | | | | | | | | Make sure sysupgrade on NAND also works in case of UBI volumes having index >9. While at it, also make sure UBI device is detected and abort in case it isn't. Use Shell built-in shorthand ':' instead of 'true'. Fixes #9708 Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0dbca1b2baf9c26514b517a1e5860f6a5b04d5ae)
* scripts/gen_image_generic.sh: generate reproducible EFI filesystemDaniel Golle2022-04-151-2/+3
| | | | | | | | | | Generate FAT filesystem for EFI boot in a reproducible way: * use '--invariant' option of mkfs.fat * set timestamps of all files to SOURCE_DATE_EPOCH * make sure files are ordered locale-independent Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit aece8f5ae8d15e5e79b8e34a176895209709afb6)
* scripts/gen_image_generic.sh: make ext4 bootfs reproducibleDaniel Golle2022-04-151-1/+1
| | | | | | | | Set fixed timestamp for kernel other files in /boot filesystem. This should help making x86 *combined* images reproducible. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 068ea2cde04e2666fb05731cea941bccfaeddc25)
* mediatek/mt7622: enable accelerated crypto driversEneas U de Queiroz2022-04-151-0/+10
| | | | | | | | | | Use ARMv8 Crypto Extensions for AES, ghash and sha256. This results in a 16 times speed gain in speed for aes-128-ctr, 17x in aes-128-gcm, and 9 times in sha256. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit c9c2b01b8441195807e8b492c7d3e385e6c6afdc)
* ath79: add support for Yuncore A930Thibaut VARÈNE2022-04-153-0/+129
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit a05dcb07241aa83a4416b56201e31b4af8518981)
* ath79: add support for Yuncore XD3200Thibaut VARÈNE2022-04-156-2/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit c91df224f54fdd44c9c0487a8c91876f5d273164)
* toolchain: musl: Update to version 1.2.3Hauke Mehrtens2022-04-132-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: new features: - qsort_r function (POSIX-future) - pthread_getname_np extension function - hard float on SPE FPU for powerpc-sf - SEEK_DATA and SEEK_HOLE exposed in unistd.h (Linux extensions) compatibility: - free now preserves errno (POSIX-future requirement) - setjmp is declared explicitly with returns_twice for non-GCC compilers - macro version of isascii is no longer defined for C++ - dynamic linker now tolerates zero-length LOAD segments - epoll_[p]wait is now a cancellation point - pwd/grp functions no longer fail on systems without AF_UNIX support - POSIX TZ parsing is stricter to allow more names to fallback to files - NULL is now defined as nullptr when used in C++11 or later - gettext now accepts null pointer as argument bugs fixed: - old regression in wcwidth of Hangul combining (vowel/final) letters - duplocale used wrong malloc when malloc was replaced (1.2.2 regression) - fmaf rounded wrong on archs without FE_TOWARDZERO (all softfloat archs) - popen didn't honor requirement not to leak other popen pipe fds to child - aligned_alloc and variants crashed on allocation failure - dl_iterate_phdr reported incorrect module TLS pointers - mishandling of some inputs in acoshf and expm1f and functions using them - potentially wrong-sign zero in cproj functions at infinity - multiple bugs in legacy function cuserid - minor posix_spawn file actions API conformance issues - pthread_setname_np fd leak - out-of-bound read in zoneinfo handling with distant-past times - out-of-tree builds lacked generated debug cfi for x86 asm arch-specific bugs fixed: - powerpc (32-bit) struct shmid_ds layout was wrong for some fields - time64 struct layout was wrong in sound ioctl fallback (32-bit archs) In addition it contains the following improvements: * protect stack canary from leak via read-as-string by zeroing second byte * fix excessively slow TLS performance on some mips models Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Rui Salvaterra <rsalvaterra@gmail.com> Tested-by: Rui Salvaterra <rsalvaterra@gmail.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> (cherry picked from commit 685ae2687bd1b199dc83ee1e16d47c05afca6102)
* mac80211: backport minstrel_ht fix for legacy ratesFelix Fietkau2022-04-121-0/+61
| | | | | | | Fixes OFDM rates on 5 GHz Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 5d5afd51772c9a992cb6bb9e0a9dce6feaa3fdef)
* musl-fts: add host buildRosen Penev2022-04-111-0/+2
| | | | | | | This will be used for libselinux. Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit 1fb099341e5879a8c5247020e5056676ba2f0745)
* kernel: Fix oob layout of XTX XT26G0xAFelix Matouschek2022-04-111-3/+3
| | | | | | | | | | | | | | | | The correct oob layout is: ECC: region->offset = 48; region->length = 16; Free: /* Reserve 1 byte for the BBM. */ region->offset = 1; region->length = 47; Signed-off-by: Felix Matouschek <felix@matouschek.org> (cherry picked from commit a5de91a88a8a33ced147bb5340fd45599f652d4d)
* kernel: Fix readid method of XTX XT26G0xAFelix Matouschek2022-04-111-3/+3
| | | | | | | The correct readid method is SPINAND_READID_METHOD_OPCODE_ADDR. Signed-off-by: Felix Matouschek <felix@matouschek.org> (cherry picked from commit 3711aee56d864fab066d76afadc9d04e1c18102e)
* nftables: add CONFLICT between versionsEneas U de Queiroz2022-04-111-1/+2
| | | | | | | Have nftables-json conflict with nftables-nojson. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit 1135b75d1fd26049a0644b304b7199e4a73c6a08)
* mac80211: Update to version 5.15.33-1Hauke Mehrtens2022-04-1133-439/+85
| | | | | | | | | | | | | | | This updates mac80211 to version 5.15.33-1 which is based on kernel 5.15.33. The removed patches were applied upstream. This new release contains many fixes which were merged into the upstream Linux kernel. This also contains the following new drivers which are needed for ath11k: * net/qrtr/ * drivers/bus/mhi/ Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 3aa96efa24c13c6e0aafa5ad826f3f95a3bd74f9)
* wolfssl: bump to 5.2.0Eneas U de Queiroz2022-04-114-9/+7
| | | | | | | | | | | | | | | | | Fixes two high-severity vulnerabilities: - CVE-2022-25640: A TLS v1.3 server who requires mutual authentication can be bypassed. If a malicious client does not send the certificate_verify message a client can connect without presenting a certificate even if the server requires one. - CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS v1.3 server can have its certificate heck bypassed. If the sig_algo in the certificate_verify message is different than the certificate message checking may be bypassed. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit e89f3e85eb1c1d81294e5d430a91b0ba625e2ec0)
* imagebuilder: export SOURCE_DATE_EPOCH to environmentDaniel Golle2022-04-101-0/+1
| | | | | | | | | Export SOURCE_DATE_EPOCH to environment so filesystem and image creation tools will make use of it. Fixes reproducibility of images generated with the ImageBuilder. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 5cf5dce05ae829ec848ad63a6da300c4fddcd510)
* arm-trusted-firmware-mediatek: remove no longer needed Configure stepDaniel Golle2022-04-101-4/+0
| | | | | | | | | As anyway only the default is called now we can as well also just remove the override for Build/Configure. Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit dffad93d3e34275b87d97724e64447d8bde537ff)
* trusted-firmware-a.mk: make sure include directory existsDaniel Golle2022-04-101-0/+3
| | | | | | | | | | | | | ARM Trusted Firmware builds do not depend on any target libraries as they are bare-metal builds. However, the compiler aborts due to -Werror=missing-include-dirs if the include dir doesn't exists and this can happen when building with parallelisation as that makes it likely for arm-trusted-firmware-* to be build very early before any of the libraries which would implicitely create the directory. Fix this by making sure the include dir exists before building. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 738d44f5ea6f6450c2c8a29cf5836e22b479340b)
* kernel: bump 5.10 to 5.10.110John Audia2022-04-1058-211/+93
| | | | | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-5.10/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch generic/pending-5.10/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch ipq40xx/patches-5.10/105-ipq40xx-fix-sleep-clock.patch All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Compile-/run-tested: ath79/generic (Archer C7 v2). Signed-off-by: Daniel Golle <daniel@makrotopia.org> [rebased in 22.03 tree] Signed-off-by: John Audia <graysky@archlinux.us> (cherry picked from commit b92ec82235b996ece32bc84af177adf1a4dcb90e)
* ipq40xx: add RT-AC2200 alternative name to RT-AC42U/RT-ACRH17Ray Wang2022-04-101-0/+2
| | | | | | | RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5. Signed-off-by: Ray Wang <raywang777@foxmail.com> (cherry picked from commit 3204906569768cabcbedb5eaa3a11e2fcb18cd48)
* ath79: Move TPLink WPA8630Pv2 to ath79-tiny targetJoe Mullally2022-04-109-42/+95
| | | | | | | | | | | | | | | | | | | | | | | | | | | | These devices only have 6MiB available for firmware, which is not enough for recent release images, so move these to the tiny target. Note for users sysupgrading from the previous ath79-generic snapshot images: The tiny target kernel has a 4Kb flash erase block size instead of the generic target's 64kb. This means the JFFS2 overlay partition containing settings must be reformatted with the new block size or else there will be data corruption. To do this, backup your settings before upgrading, then during the sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n". If you forget to do this and your system becomes unstable after upgrading, you can do this to format the partition and recover: * Reboot * Press RESET when Power LED blinks during boot to enter Failsafe mode * SSH to 192.168.1.1 * Run "firstboot" and reboot Signed-off-by: Joe Mullally <jwmullally@gmail.com> Tested-by: Robert Högberg <robert.hogberg@gmail.com> (cherry picked from commit 44e1e5d153d00915a7e516c9af3f440cbd84cf78)
* dropbear: bump to 2022.82Konstantin Demin2022-04-109-66/+90
| | | | | | | | | | | | | | | | | | | | | | | - update dropbear to latest stable 2022.82; for the changes see https://matt.ucc.asn.au/dropbear/CHANGES - use $(AUTORELEASE) in PKG_RELEASE - use https for all uris - refresh all patches - rewrite patches: - 100-pubkey_path.patch - 130-ssh_ignore_x_args.patch binary/pkg size changes: - ath79/generic, mips: - binary: 215112 -> 219228 (+4116) - pkg: 111914 -> 113404 (+1490) - ath79/tiny, mips: - binary: 172501 -> 172485 (-16) - pkg: 89871 -> 90904 (+1033) Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Konstantin Demin <rockdrilla@gmail.com> (cherry picked from commit 65256aee23a5104eb0c78411fdc73640c0b757ea)
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 18:47:52 +0000