| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
(cherry picked from commit 39799974a372fb4333d21f077c670b8a56b9d696)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There are two versions which are identical apart from the enclosure:
YunCore AX820: indoor ceiling mount AP with integrated antennas
YunCore HWAP-AX820: outdoor enclosure with external (N) connectors
Hardware specs:
SoC: MediaTek MT7621DAT
Flash: 16 MiB SPI NOR
RAM: 128MiB (DDR3, integrated)
WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
LED: Status (green)
Button: Reset
Power: 802.11af/at PoE; DC 12V,1A
Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external
Flash instructions:
The "OpenWRT support" version of the AX820 comes with a LEDE-based
firmware with proprietary MTK drivers and a luci webinterface and
ssh accessible under 192.168.1.1 on LAN; user root, no password.
The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
you will have to force the upgrade due to a different factory name.
Remember: Do *not* preserve factory configuration!
MAC addresses as used by OEM firmware:
use address source
2g 44:D1:FA:*:0b Factory 0x0004 (label)
5g 46:D1:FA:*:0b LAA of 2g
lan 44:D1:FA:*:0c Factory 0xe000
wan 44:D1:FA:*:0d Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.
Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
(cherry picked from commit 4891b865380e2b7f32acf0893df9c1ca9db8d4ea)
|
|
|
|
|
|
|
|
|
|
| |
Includes image support for new TP-Link devices:
ddc3e00e314d tplink-safeloader: add TP-Link EAP265 HD support
ceea1a7fe56e tplink-safeloader: add TP-Link Deco M4R v1 and v2 support
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 0f207ade12fdfffae3554c6a7214aa670a8d6854)
|
|
|
|
|
|
|
| |
05fd700 tplink-safeloader: TP-Link RE650 v2 support
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 36790ca6940b84dede450c54df9f75500454b92b)
|
|
|
|
|
|
|
|
|
|
|
|
| |
This backports a patch from Linux 5.10.116 to fix a compile problem
introduced in 5.10.114.
drivers/usb/phy/phy-generic.c could not find
devm_regulator_get_exclusive().
Fixes: 8592df67f40b ("kernel: bump 5.10 to 5.10.114")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7400adae8d86dde3c60752bf66d487aa1b138bc1)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed:
backport-5.10/850-v5.17-0004-PCI-aardvark-Clear-all-MSIs-at-setup.patch
pending-5.10/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit b754b0c721131005efa7127151088e9c23dc9053)
|
|
|
|
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 8592df67f40b3afdee68e36dc3820187ec0f98fc)
|
|
|
|
|
|
|
|
|
|
| |
Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit f167f4a9a42e6d1e186487883500299cc82b1b9f)
|
|
|
|
|
|
|
|
|
| |
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 byte OOB. This adds a static NAND ID entry to correct this.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 0bc794a66845738eef7eeb7e13877ffb8aec17f7)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
From Andreas Böhler:
"Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC
in contrast to the Macronix NAND with 4 bit ECC.".
Uboot needs to know this in order to have a chance to load from
the NAND.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 057bac2e1fc796fb4b2440a896be43bca138be84)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ZTE MF286A and MF286R feature a "power switch override" GPIO in stock
firmware as means to prevent power interruption during firmware update,
especially when used with internal battery.
To ensure that this GPIO is
properly driven as in stock firmware, configure it with userspace GPIO
switch.
It was observed that on some units, the modem would not be
restarted together with the board itself on reboot, this should help
with that as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 1fabeeb799abca1d4fb5ba541410ba847cdc20d9)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This partially reverts
commit cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data").
After switching to nvmem RTL30VW, wifi was broken:
[ 19.118319] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 19.118377] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 19.130285] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[ 19.159092] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[ 19.238764] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[ 19.238847] ath10k_ahb a000000.wifi: failed to fetch board file: -12
[ 19.247362] ath10k_ahb a000000.wifi: could not probe fw (-12)
[ 20.190797] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 20.190853] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 20.202893] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[ 20.231357] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[ 20.317318] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[ 20.317399] ath10k_ahb a800000.wifi: failed to fetch board file: -12
[ 20.326098] ath10k_ahb a800000.wifi: could not probe fw (-12)
Bootloader mangles in NAND partitions and removes precal@X nodes in
working system:
root@OpenWrt:~# echo $(cat /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/label)
0:ART
root@OpenWrt:~# ls /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/
label name reg
Revert to legacy method fixed the problem.
Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit af425e42212d476dd95ec31f18d85b19004c9268)
|
|
|
|
|
|
|
|
|
|
|
|
| |
On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree.
Because of GPIO_OUT_FUNCTION4 register was not initialized on start,
GPIO17 was uncontrollable, it always in high state. According to QCA9531
documentation, default setting of GPIO17 is SYS_RST_L. In order to make
GPIO17 controllable, it should write value 0x00 on bits [15:8] of
GPIO_OUT_FUNCTION4 register, located at 0x1804003C address.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
(cherry picked from commit 57efdd6a2d815d2491c5b7f22ffaeb6a845bfd0a)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add the reg and color property to each channel node. This
update is to accommodate the multicolor framework.
Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>
Note:
There is only a single extremely bright RGB-LED.
The RGB-color channels (i.e.: blue-0, blue-1 and blue-2)
are running in parallel to increase the current delivery
beyond what a single PWM-output on the LED controller
could do.
BugLink: https://github.com/openwrt/openwrt/issues/9851
Reported-By: Thomas Bøge <thomas@boegenielsen.dk>
Tested-By: Thomas Bøge <thomas@boegenielsen.dk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 834c9b3f055e5ea719f6adfb3fa979e32f2adbd0)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
None of the devices supported by target xway are using Realtek
RTL8366S, RTL8367A and RTL8367B switches. The switches mentioned
earlier were enabled when bumping the kernel version to 3.7 in
commit 3a948770cf46 ("add linux-v3.7").
Switches used by individual devices are listed below.
Device Switch PHY
Arcadyan ARV4510PW Infineon ADM6996I int. switch
Arcadyan ARV4519PW Atheros AR8216 int. switch
Arcadyan ARV7506PW11 Realtek RTL8306G int. switch
Arcadyan ARV7510PW22 Atheros AR8216 int. switch
Arcadyan ARV7518PW Atheros AR8216 int. switch
Arcadyan ARV7519PW Atheros RTL8306G int. switch
Arcadyan ARV7525PW N/A IC+ IP101A
Arcadyan ARV752DPW Realtek RTL8306G int. switch
Arcadyan ARV752DPW22 Atheros AR8216 int. switch
Arcadyan ARV8539PW22 Atheros AR8216 int. switch
AVM Fritzbox 7312 int. SoC Atheros AR8030-A
AVM Fritzbox 7320 int. SOC Lantiq PEF7071V
AudioCodes MediaPack MP-252 Infineon ADM6996I int. switch
BT Home Hub 2B Infineon ADM6996I int. switch
BT Home Hub 3A Infineon PSB6972 Lantiq PEF7071V
Buffalo WBMR-HP-G300H-A Atheros AR8316 int. switch
Buffalo WBMR-HP-G300H-B Atheros AR8316 int. switch
Lantiq EASY50712 Infinein ADM6996I int. switch
Netgear DGN3500 Realtek RTL8366RB int. switch
Netgear DGN3500B Realtek RTL8366RB int. switch
Siemens Gigaset sx76x Infineon ADM6996I int. switch
ZTE H201L Realtek RTL8306G int. switch
ZyXEL P-2601HN-F1 Realtek RTL8306E int. switch
ZyXEL P-2601HN-F3 Realtek RTL8306E int. switch
Reduces uncompressed kernel size by 36 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(checkpatch.pl fixes)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 8b5d2a73255298b916259ccbc609e4667a335844)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Do not reset the RTL930x SerDes on link changes, instead set up
the SDS with internal PHYs for the SFP+ ports only.
This fixes the 8 1GBit ports on the Zyxel XGS1250 which
do not work without this patch.
A complete SerDes reset was performed on all SerDes links. For copper
1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There
is however no support for setting up the XGMII link on RTL9300/RTL9310,
thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit
ports. No SerDes reset should be done for these links.
The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely
different. All these modes need to be suitably RX calibrated and the
pre- main and post- amplifiers set up properly for TX.
The 10GBit SFP+ fiber links are recalibrated instead of reset, which
e.g. is necessary when someone pulls a module out and puts another in.
This makes swapping out 10GBit fiber modules possible. 1GBit modules are
not yet supported, nor any modules with an internal phy.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[rewrite commit message based on discussion]
Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit d1b824650f1ee694ec2dbdd2f4f9ec64e650cf86)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes a bug where frames sent to the switch itself were
flooded to all ports unless the MAC address of the CPU-port
was learned otherwise.
Tested-by: Wenli Looi <wlooi@ucalgary.ca>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[fix code formatting]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 98bb26f9f762408e42bd8a906f0eb01c41ada10a)
|
|
|
|
|
|
|
|
|
| |
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 064e7e57b483e6879de0facef4f1fce86ec4ad47)
|
|
|
|
|
|
|
|
|
|
| |
There are many ways to add external RTC to Raspberry Pi boards. Let's
include support for this for the whole target and while at it, sort
features alphabetically.
Fixes: #9594
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit ff09905a468b4cc44f039a76568e8fe6cbaea8d9)
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 203ffc4ca75d43ac32b164c5a474e3ce36999809)
|
|
|
|
|
|
|
| |
sync xt_FLOWOFFLOAD code with latest version of nft_flow_offload
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 726ef8ba2dbe4d4a693c4d9300bc69e234e6d67d)
|
|
|
|
|
|
|
| |
This series also contains other improvement for hardware flow offload support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 0f029b3d2b505b40aca9a24a002838ed1060f83d)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove restrictions on source and destination addresses, which aren't
specified on RFC8415, and for some reason in openwrt are configured
to allow both link-local and ULA addresses.
As cleared out in issue #5066 there are some ISPs that use Gloabal
Unicast addresses, so fix this rule to allow them.
Fixes: #5066
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
[rebase onto firewall3, clarify subject, bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 65258f5d6093809c541050256646795bc0a460a9)
|
|
|
|
|
|
|
| |
9e11b37 fstools: remove SELinux restorecon hack
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4509b790f09183b2ac757371f6d79052f232e4cd)
|
|
|
|
|
|
|
| |
652e6df init: restore SELinux labels after policy is loaded
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fb011118664756ee33bf16a39bf6e73d02cc2d3f)
|
|
|
|
|
|
|
|
|
|
| |
Remove forgotten redundant selinuxenabled call and skip the whole
thing in case $IPKG_INSTROOT is set as labels are anyway applied only
later on in fakeroot when squashfs is created.
Fixes: 6d7272852e ("base-files: add missing $IPKG_INSTROOT to restorecon call")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7b07c3cff57f057d6780d34adeb23c06123732db)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
try to clean up some labeling inconsistencies
iwinfo loose ends
ucode loose ends
Makefile: adjust mintesttgt (adds blockmount/blockd)
nftables: reads inherited netifd pipe
ucode: reads inherited netifd pipes
mountroot: fowner
sandbox: writes inherited dropbear pipes
unbound related to /tmp/etc/ssl
unbound loose ends
adds a sslconftmpfile for /tmp/etc/ssl
README: maintain a wish list in the README
iwinfo: netifd forgot write
gptfdisk loose ends
iwinfo: netifd wpad reads/writes inherited netifd fifo files
netifd (mac80211.sh) executes iwinfo
luci: executes wireguard
luci-cgi: audits xtables execute access
rcuhttpd: lists ssl certfile dirs
iwinfo, wifi,nftables usage of ttyd pty if available
urandomseed: seedrng needs cap_sys_admin
iwinfo iwinfo, nftables and some chronyd rules related to ntp nts server
nftables, wifi and adds iwinfo skel
nftables, rpcd, ucode
nftables, ucode and seedrng ucode, fw3/nftables, luci
adds ucode skel and some fw3/nftables related
urandomseed: some seedrng rules
fw3 adds some support for fw4
urandomseed: /etc/seedrng is for seed.credit
hotplugcal: runs ucode which is interpreter like
adds a nftables skeleton and makes xtables optional
agent: allow all agents to write inherited dropbear pipes
urandomseed: this seems to be replaced by seedrng
kmodloader: label /etc/modules.conf kmodloader.conffile
Revert "shelexecfile: remove auditallow rule"
Makefile: sort the modules to process by secilc
Moves back to git.defensec.nl
unbound odhcpd (ip) reads net proc
tcp dump
shelexecfile: remove auditallow rule
rrd.cil: fixes indent
Target rddtool from cgi-io instead of runnit it without transition
rrd.cil related
rrd, rpcd, cgiio clean ups related to luci-app-statistics
Rules for rrd files and luci-statistics
unboundcontrol ordering
Several missing permissions
blockmount, dnsmasq, hotplugcall, rpcd, unbound
adds mctp_socket (linux 5.15)
ip: forgot tc-tiny type transition to go along with the fc spec
ip: adds a fc spec for tc-tiny (called by sqm)
adds ttyACM fc spec and various assorted loose ends
.gitattributes: do not export the github workflows
workflow use selinux 3.3
project moved back to https://git.defensec.nl/selinux-policy.git
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
(cherry picked from commit 43794570986e33770d9039399d16a665f6c7c495)
|
|
|
|
|
|
|
|
| |
Update to overlooked v2 version of Dominick Grift's patch.
Fixes: 5109bd164c ("base-files: address sed in-place without SELinux awareness")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6d7272852e0b2634b2fa93a131ea8659ec87f079)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
sed(1) in busybox does not support this functionality:
https://git.savannah.gnu.org/cgit/sed.git/tree/sed/execute.c#n598
This causes /etc/group to become mislabeled when a package requests
that a uid/gid be added on OpenWrt with SELinux
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[move restorecon inside lock]
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
(cherry picked from commit 5109bd164c8f2273329483f990188fb36cf3ad68)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
f0fc66a libfstools: check for overlay mounting errors
128ecaf Update / fix extroot comments
8a0ba3b libfstools: get rid of "extroot_prefix" global variable
649cd3f libfstools: use variable for overlay mount-point
922f1b3 libfstools: avoid segfault in find_mount_point
ce5eacb libfstools: mtd: improve error handling
898b328 blockd: restore device_move semantics
0917d22 block: don't probe mtdblock on NAND (with legacy exceptions)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4e8d095013fb822eaa4fd6b4512a434fc17ac901)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After the switch to pre-calibration, ath10k would fail to initialize
the PCIE Wi-Fi on the GL-B200 as follows:
ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[...]
ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=GL-B2200 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:01:00.0: failed to fetch board file: -12
ath10k_pci 0000:01:00.0: could not probe fw (-12)
Repackage the BDF file after renaming relevant fields and files to
allow for the Wi-Fi interface to start again.
Fixes: 80d34d9d593 ("ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200")
CC: Christian Lamparter <chunkeey@gmail.com>
CC: Robert Marko <robimarko@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit e3f9af4fb6e4ba8bf54cb4240f318ad32260a6fa)
|
|
|
|
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
(cherry picked from commit e08942e76a162962892020a0f7e52ef751ec68e4)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased:
ath79/patches-5.10/901-phy-mdio-bitbang-prevent-rescheduling-during-command.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
(cherry picked from commit cab20be008591f89dd89c4e444cdf022fa7f57eb)
|
|
|
|
|
|
|
|
|
|
| |
resolve issue
- https://github.com/openwrt/openwrt/issues/9800
add the upstream patch:
- f2fs-tools.git/patch/?id=f056fbeff08d30a6d9acdb9e06704461ceee3500
Signed-off-by: Kerma Gérald <gandalf@gk2.net>
(cherry picked from commit 1aac1b36d3cf44c8bfa8d4a6d8df6e815fc06529)
|
|
|
|
|
|
|
|
|
|
|
| |
Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.
Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
(cherry picked from commit 6e9c814022e41a7cfa4db3b1a41e257fd1515bea)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In commit 7e614820a892 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
This change fixes Github issue #9779 [1].
[1]: https://github.com/openwrt/openwrt/issues/9779
Fixes: 7e614820a892 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(cherry picked from commit 1d06277407d3e294589ecde46328303a9f3803fd)
|
|
|
|
|
|
|
|
| |
targetclean should not remove BUILD_LOG
Fixes: db34b93331e9 (add a version that can be bumped to force toolchain/target rebuild)
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
(cherry picked from commit aeaa816cd2bd22de165c71a41d8d198a9235e971)
|
|
|
|
|
|
|
|
|
| |
If logfacility is a path to a file it needs to be r/w mounted in the
sandbox as well for dnsmasq to work.
Reported-by: @iointerrupt
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b5fa44f60165d66d74131778df0b64b706887e2)
|
|
|
|
|
|
|
| |
These don't have switches that could be configured using swconfig.
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
(cherry picked from commit 089eb02abcd7512c6d182953560eb2453ef144ca)
|
|
|
|
|
|
|
| |
The `Description` should be capital.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
(cherry picked from commit b8ed98b10004d5de25c1b4b2d2b59b15fc04f794)
|
|
|
|
|
|
|
|
|
|
|
|
| |
When adding support to the router's built-in modem, this required
package was omitted, because it was already enabled in the image
configuration in use for testing, and this went unnoticed.
In result, the modem still isn't fully supported in official images.
As it is the primary WAN interface, add the missing package.
Fixes: e02fb42c53ba ("comgt: support ZTE MF286R modem")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 8a1003c5986514d7a78f78b3ee94003837d82582)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Signed-off-by: Alban Bedel <albeu@free.fr>
(cherry picked from commit f953a1a4bfba2fa70c12bb80938aa66481a673b6)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.
Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617
- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072
Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit ab7e53e5cce703c7a62efbe1d41fb94c2228a178)
|
|
|
|
|
|
|
|
|
|
| |
Ensure that the libucode recipe is processed before the ucode one in
order to reliably encode the ABI version into ucode's libucode dependency.
Fixes: #9788
Ref: https://forum.openwrt.org/t/fw4-wont-start-after-upgrade/126308
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 573ce80ca612b0f642b7cbd5d9d33d89b7e96670)
|
|
|
|
|
|
|
| |
dc6847e iwinfo: nl80211: omit A-hwmode on non-5GHz hardware
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f757a8a09885e3c8bb76371e037b8c0731111980)
|
|
|
|
|
|
|
|
| |
Add configuration to use uboot-envtools with the Extreme Networks
WS-AP3825i.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit fb7ff6b027d1c69e97e6d39e688a969c164065c8)
|
|
|
|
|
|
|
|
|
|
| |
The bootloader does seem to not correctly patch in the MAC address for
eth0 / eth1 in some cases. While the root cause is not known, manually
applying the MAC-Address in preinit does not hurt.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c6d52515e009d96e0afbe77310bf172f113d0eef)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The WS-AP3825i uses Atheros PHYs which according to the datasheet
require the reset to be asserted for at least 1 ms.
This fixes broken eth1 upon soft-reboot. eth0 is no affected, as the
ifup / ifdown cycle in preinit prevents this issue from happening when
the system is ready.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8b3c313515c1ae37be9d61a4e92c4bf4b43f605f)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
fc83d46 ruleset: set auto-merge directive for interval sets
9bce873 fw4: fix skipping invalid ipset entries
425ea8a fw4: fix applying zone flags for source bound rules
a378883 fw4: fix emitting family specific redirect rules without any addrs
11feddf fw4: bracketize IPv6 addresses in dnat addr:port notation
9972f7d fw4: ensure to capitalize weekday names
fde8070 treewide: forward compatibility changes
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commits 1a35ac99905adc35059489d6e19c7de42ef4cc01 and
af02a12d7ccb64a3abbd9683dd22275b538f6d50)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
e14b099 syntax: implement support for ES6 template literals
111cf06 vm: stop executing bytecode on return of nested calls
33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commits cef3e6a69c4751189e946cf2ff0e00304f9fff6e,
0400774a1001835b912ecf2097bba1306deba9f8 and
c59704334c4a01bc18ab489f86d4ca7d2ea3cb8f)
|