aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add LTE packages for GL-AP1300David Bauer2022-09-091-1/+1
| | | | | | | | Add LTE packages required for operating the LTE modem optionally shipped with the GL-AP1300. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit c7c350922668e262068c9301b75434d7bb4b8d10)
* ath79: add support for ZTE MF281David Bauer2022-09-083-4/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the ZTE MF281 battery-powered WiFi router. Hardware -------- SoC: Qualcomm Atheros QCA9563 RAM: 128M DDR2 FLASH: 2M SPI-NOR (GigaDevice GD25Q16) 128M SPI-NAND (GigaDevice) WLAN: QCA9563 2T2R 802.11 abgn QCA9886 2T2R 802.11 nac WWAN: ASRMicro ASR1826 ETH: Qualcomm Atheros QCA8337 UART: 115200 8n1 Unpopulated connector next to SIM slot (SIM) GND - RX - TX - 3V3 Don't connect 3V3 BUTTON: Reset - WPS LED: 1x debug-LED (internal) LEDs on front of the device are controlled using the modem CPU and can not be controlled by OpenWrt Installation ------------ 1. Connect to the serial console. Power up the device and interrupt autoboot when prompted 2. Connect a TFTP server reachable at 192.168.1.66 to the ethernet port. Serve the OpenWrt initramfs image as "speedbox-2.bin" 3. Boot the initramfs image using U-Boot $ setenv serverip 192.168.1.66 $ setenv ipaddr 192.168.1.154 $ tftpboot 0x84000000 speedbox-2.bin $ bootm 4. Copy the OpenWrt factory image to the device using scp and write to the NAND flash $ mtd write /path/to/openwrt/factory.bin firmware WWAN ---- The WWAN card can be used with OpenWrt. Example configuration for connection with a unauthenticated dual-stack APN: network.lte=interface network.lte.proto='ncm' network.lte.device='/dev/ttyACM0' network.lte.pdptype='IPV4V6' network.lte.apn='internet.telekom' network.lte.ipv6='auto' network.lte.delay='10' The WWAN card is running a modified version of OpenWrt and handles power-management as well as the LED controller (AW9523). A root shell can be acquired by installing adb using opkg and executing "adb shell". Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 1e1695f959e678868bb7911d059b847f38fc9cf4)
* realtek: fix RTL838x receive tag decodingBjørn Mork2022-09-081-3/+6
| | | | | | | | | | | | | | | | | | | | Commit dc9cc0d3e2a1 ("realtek: add QoS and rate control") replaced a 16 bit reserved field in the RTL83xx packet header with the initial cpu_tag word, shifting the real cpu_tag fields by one. Adjusting for this new shift was partially forgotten in the new RX tag decoders. This caused the switch to block IGMP, effectively blocking IPv4 multicast. The bug was partially fixed by commit 9d847244d9fd ("realtek: fix RTL839X receive tag decoding") Fix on RTL838x too, including correct NIC_RX_REASON_SPECIAL_TRAP value. Suggested-by: Jan Hoffmann <jan@3e8.eu> Fixes: dc9cc0d3e2a1 ("realtek: add QoS and rate control") Signed-off-by: Bjørn Mork <bjorn@mork.no> (cherry picked from commit 545c6113c93bbf7de1b0e515141a4565f7e6cece)
* mt76: update to the latest versionFelix Fietkau2022-09-061-3/+3
| | | | | | | d70546462b7b mt76: fix 5 GHz connection regression on mt76x0/mt76x2 Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 33c11442b2fc60313a2d3196c9b01cf9b0931305)
* hostapd: rename hostapd multicast_to_unicast option to multicast_to_unicast_allFelix Fietkau2022-09-061-5/+5
| | | | | | | | | | | | | | | | | | | | | There are two feature currently altered by the multicast_to_unicast option. 1. bridge level multicast_to_unicast via IGMP snooping 2. hostapd/mac80211 config multicast_to_unicast setting The hostapd/mac80211 setting has the side effect of converting *all* multicast or broadcast traffic into per-station duplicated unicast traffic, which can in some cases break expectations of various protocols. It also has been observed to cause ARP lookup failure between stations connected to the same interface. The bridge level feature is much more useful, since it only covers actual multicast traffic managed by IGMP, and it implicitly defaults to 1 already. Renaming the hostapd/mac80211 option to multicast_to_unicast_all should avoid unintentionally enabling this feature Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 09ea1db93b53d2c1e4a081f20fbbddd4bffd451d)
* bcm27xx: make NVMEM driver patch apply againRafał Miłecki2022-09-041-6/+7
| | | | | Fixes: 4efa0b70d54f1 ("kernel: backport U-Boot environment data NVMEM driver") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: enable NVMEM U-Boot env data driverRafał Miłecki2022-09-031-0/+3
| | | | | | | It's needed for devices with U-Boot bootloader. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit fb47b9fa1aa760de58f1b43d9f3e654acf1f1671)
* kernel: backport U-Boot environment data NVMEM driverRafał Miłecki2022-09-036-10/+361
| | | | | | | It parses U-Boot env data into NVMEM cells. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 34cf31043504473df3174a22d163b71b75e46542)
* kernel: backport mtd patch adding of_platform_populate() callsRafał Miłecki2022-09-033-8/+81
| | | | | | | This is required for non-parser drivers handling MTD devices. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 41e1e838fbbb0308ad7353a3714e04b8c4585e7e)
* OpenWrt v22.03.0: revert to branch defaultsHauke Mehrtens2022-09-035-11/+9
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* OpenWrt v22.03.0: adjust config defaultsv22.03.0Hauke Mehrtens2022-09-035-9/+11
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-mediatek: mt7622: suppress unwanted pinctrl warningDaniel Golle2022-09-033-6/+47
| | | | | | | Import patch which removes the default pinctrl of uart0 to suppress the unwanted warning. Apply also to downstream boards. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: fix DTS compatible of UniFi 6 LR variantsDaniel Golle2022-09-033-3/+3
| | | | | | | | Make sure the compatible string in DTS matches the now v1/v2 differentiated board name in target/linux/mediatek/image/mt7622.mk. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit be555b9dd8618b8da68c42ae8dda493337519838)
* uboot-mediatek: backport fix for unstable UART on MT7622Daniel Golle2022-09-031-0/+26
| | | | | | | | | | | | | Import pending patch "arm: dts: mt7622: force high-speed mode for uart" from Weijie Gao <weijie.gao@mediatek.com> fixing the UART problems on MT7622 which made it hard to use the U-Boot menu on devices with this SoC. This patch is also contained in commit c09eb08dad ("uboot-mediatek: add support for MT798x platforms") in the development branch. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: no compression means IH_COMP_NONEDaniel Golle2022-09-034-4/+121
| | | | | | | | | | | Treat missing compression node in FIT image as IH_COMP_NONE. This is implicentely already happening in most places, but for now was still triggering an annoying warning about initramfs compression being obsolete despite compression note being absent. Fix this. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0a18456ffc25d6a26911fca6f9079090243c2284)
* uboot-mediatek: fix factory reset on UBIDaniel Golle2022-09-032-2/+2
| | | | | | | | Truncating a UBI volume using `ubi write 0x0 volname 0x0` results in segfault on newer U-Boot. Write 1MB of 0s instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit d118cbdfece181994a96d1bcb1868bd807d481bf)
* uboot-envtools: mt7622: use 4k sectors for UniFi 6 LR (ubootmod)Daniel Golle2022-09-031-1/+1
| | | | | | | | | Use 4k sectors when accessing the U-Boot environment on the 64MiB SPI-NOR flash chip found in the UniFi 6 LR. The speeds up environment write access as only 4kB instead of 64kB have to be written. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit f0adf253fdcf78ce005dad9652b405a4ad2726e6)
* mediatek: mt7622: use variable sector size for spi-norDaniel Golle2022-09-031-0/+1
| | | | | | | Make use of minor sector size (4k) on supported SPI-NOR flash chips. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 51f4c8417819bc0ba6bc1808328478503e179fc4)
* uboot-mediatek: fix Ubiquiti UniFi 6 LR U-Boot modDaniel Golle2022-09-031-20/+8
| | | | | | | | Image names as well as the calculation of the padded image size did not work as intended. Fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0bc8889e7b4f19d7e33a9be6c3db918fed051501)
* mpc85xx: Drop pci aliases to avoid domain changesMartin Kennedy2022-09-026-0/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As of upstream Linux commit 0fe1e96fef0a ("powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and alias"), the PCIe domain address is no longer numbered by the lowest 16 bits of the PCI register address after a fallthrough. Instead of the fallthrough, the enumeration process accepts the alias ID (as determined by `of_alias_scan()`). This causes e.g.: 9000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11) 9000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ... to become 0000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11) 0000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ... ... which then causes the sysfs path of the netdev to change, invalidating the `wifi_device.path`s enumerated in `/etc/config/wireless`. One other solution might be to migrate the uci configuration, as was done for mvebu in commit 0bd5aa89fcf2 ("mvebu: Migrate uci config to new PCIe path"). However, there are concerns that the sysfs path will change once again once some upstream patches[^2][^3] are merged and backported (and `CONFIG_PPC_PCI_BUS_NUM_DOMAIN_DEPENDENT` is enabled). Instead, remove the aliases and allow the fallthrough to continue for now. We will provide a migration in a later release. This was first reported as a Github issue[^1]. [^1]: https://github.com/openwrt/openwrt/issues/10530 [^2]: https://lore.kernel.org/linuxppc-dev/20220706104308.5390-1-pali@kernel.org/t/#u [^3]: https://lore.kernel.org/linuxppc-dev/20220706101043.4867-1-pali@kernel.org/ Fixes: #10530 Tested-by: Martin Kennedy <hurricos@gmail.com> [Tested on the Aerohive HiveAP 330 and Extreme Networks WS-AP3825i] Signed-off-by: Martin Kennedy <hurricos@gmail.com> (cherry picked from commit 7f4b4c29f3489697dca7495216460d0ed5023e02)
* at91bootstrap: use sdmmc0 as booting media for sama5d27_som1_ekClaudiu Beznea2022-09-022-9/+3
| | | | | | | | | | | Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as default defconfig") changed default booting media for sama5d27_som1_ek board w/o any reason. Changed it back to sdmmc0 as it is for all the other Microchip supported distributions for this board (Buildroot, Yocto Project). The initial commit cannot be cleanly reverted. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> (cherry picked from commit e9f12931e60ee291cd7d2c8fd19a14682dae0197)
* uboot-at91: use sdmmc0 as booting media for sama5d27_som1_ekClaudiu Beznea2022-09-023-16/+10
| | | | | | | | | | | | Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs") changed the booting media to sdmmc1 as default booting w/o any reason. The Microchip releases for the rest of supported distributions (Buildroot, Yocto Project) uses sdmmc0 as default booting media for this board. Thus change it back to sdmmc0. With this remove references to sdmmc1 config. The initial commit cannot be cleanly reverted. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> (cherry picked from commit 9a49788008c18fd4fe6fefe9697962c102fb14c6)
* kernel: rename 5.20 patches to 6.0Rafał Miłecki2022-09-025-0/+0
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 372ee1919d281dd3e86121996805291a6948c982)
* bcm4908: enable & setup packet steeringRafał Miłecki2022-09-012-0/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without packet steering NAT masquarade speed on BCM4908 /jumps/ between two speeds: 1. 826 Mb/s (±3 Mb/s) 2. 909 Mb/s (±8 Mb/s) and it never reaches ~940 Mb/s. Proper packet steering can improve it. Below are testing results for running iperf TCP traffic from LAN to WAN. They were used to pick up golden values. ┌──────────┬──────────┬───────────┐ │ eth0 │ br-lan │ speed │ │ rps_cpus │ rps_cpus │ [Mbps] │ ├──────────┼──────────┼───────────┤ │ 0 │ 0 │ 743 / 804 │ │ 0 │ 1 │ 738 / 821 │ │ 0 │ 2 │ ✓ 940 │ │ 0 │ 4 │ ✓ 938 │ │ 0 │ 8 │ ✓ 941 │ ├──────────┼──────────┼───────────┤ │ 1 │ 0 │ 829 │ │ 1 │ 1 │ 829 │ │ 1 │ 2 │ ✓ 942 │ │ 1 │ 4 │ ✓ 941 │ │ 1 │ 8 │ ✓ 941 │ ├──────────┼──────────┼───────────┤ │ 2 │ 0 │ ✓ 942 │ │ 2 │ 1 │ 926 │ │ 2 │ 2 │ ✓ 942 │ │ 2 │ 4 │ ✓ 942 │ │ 2 │ 8 │ ✓ 941 │ ├──────────┼──────────┼───────────┤ │ 4 │ 0 │ ✓ 941 │ │ 4 │ 1 │ 925 │ │ 4 │ 2 │ ✓ 941 │ │ 4 │ 4 │ ✓ 941 │ │ 4 │ 8 │ ✓ 941 │ ├──────────┼──────────┼───────────┤ │ 8 │ 0 │ ✓ 942 │ │ 8 │ 1 │ 925 │ │ 8 │ 2 │ ✓ 941 │ │ 8 │ 4 │ ✓ 942 │ │ 8 │ 8 │ ✓ 942 │ └──────────┴──────────┴───────────┘ Ref: fcbd39689ebfe ("bcm53xx: enable & setup packet steering") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 57cad53f4e52be987cdd61308ff7d2704baca539)
* bcm4908: prepare for Asus GT-AX6000 supportRafał Miłecki2022-09-011-0/+10
| | | | | | | It isn't tested & Linux DT will surely need more work. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 3f2b2fe084c0019221a17e3217a01c41d003f6fd)
* bcm4908: backport bcmbca DT patches queued for 5.20Rafał Miłecki2022-09-0110-0/+1161
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit d63ef7c90f75393270ec4f5ff1b2563d6bd52066)
* bcm53xx: backport DT changes from 5.17 & 5.18Rafał Miłecki2022-09-019-1/+471
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a721fb9f839b3ca71da275a1c99620ef9342fb28)
* bcm53xx: drop dead upgrade codeRafał Miłecki2022-09-011-8/+0
| | | | | | | | platform_nand_pre_upgrade() is gone since commit 790692dde2b9 ("base-files: drop support for the platform_nand_pre_upgrade()"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a6dc0f680d3715322abd7a5dc1426f56274292ac)
* firewall4: update to latest Git HEADJo-Philipp Wich2022-09-011-3/+3
| | | | | | | | | f5fcdcf cli: introduce test mode and refuse firewall restart on errors a540f6d fw4: fix cosmetic issue with per-ruleset and per-table include paths 695e821 doc: fix swapped include positions in nftables.d README Signed-off-by: Jo-Philipp Wich <jo@mein.io> (cherry picked from commit ab31ffc425b59afc102f8a3275791c153f39c8f4)
* ucode: update to latest Git HEADJo-Philipp Wich2022-08-311-3/+3
| | | | | | | | | 344fa9e lib: extend render() to support function values 89452b2 lib: improve getenv() and split() implementations Signed-off-by: Jo-Philipp Wich <jo@mein.io> [fix commit subject] (cherry picked from commit c6d6306827e9296faad26981996825ce3e90259d)
* mac80211: disable ft-over-ds by defaultFelix Fietkau2022-08-301-1/+1
| | | | | | | | | Testing has shown it to be very unreliable in variety of configurations. It is not mandatory, so let's disable it by default until we have a better solution. Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 2984a0420649733662ff95b0aff720b8c2c19f8a)
* ramips: define Yuncore AX820 switch LEDsThibaut VARÈNE2022-08-292-0/+20
| | | | | | | | | | This patch defines the two switch LED to bring them under user control. Fixes: 158a5af80102d ("ramips: improve YunCore AX820 LEDs") Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> [rmilecki: leave "label"s in place] Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 7bee10a7d2d16251113147c28dd4548af5c14bab)
* ath79: add support for Extreme Networks WS-AP3805iAlbin Hellström2022-08-296-0/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: Qualcomm Atheros QCA9557-AT4A - RAM: 2x 128MB Nanya NT5TU64M16HG - FLASH: 64MB - SPANSION FL512SAIFG1 - LAN: Atheros AR8035-A (RGMII GbE with PoE+ IN) - WLAN2: Qualcomm Atheros QCA9557 2x2 2T2R - WLAN5: Qualcomm Atheros QCA9882-BR4A 2x2 2T2R - SERIAL: UART pins at J10 (115200 8n1) Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) - LEDs: Power (Green/Amber) WiFi 5 (Green) WiFi 2 (Green) - BTN: Reset Installation: 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to 1D01A8C0.img Configure the TFTP server to listen at 192.168.1.66/24. 2. Connect the TFTP server to the access point. 3. Connect to the serial console of the access point. Attach power and interrupt the boot procedure when prompted. Credentials are admin / new2day 4. Configure U-Boot for booting OpenWrt from ram and flash: $ setenv boot_openwrt 'setenv bootargs; bootm 0xa1280000' $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66; tftpboot 0x89000000 1D01A8C0.img; bootm' $ setenv bootcmd 'run boot_openwrt' $ saveenv 5. Load OpenWrt into memory: $ run ramboot_openwrt 6. Transfer the OpenWrt sysupgrade image to the device. Write the image to flash using sysupgrade: $ sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: Albin Hellström <albin.hellstrom@gmail.com> [rename vendor - minor style fixes - update commit message] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f8c87aa2d27ab405f284dd4357377ab5c893a345)
* kernel: Refresh on 5.10.138Hauke Mehrtens2022-08-2888-1228/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Refresh all patches on top of kernel 5.10.138. The following patches were applied upstream: bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch Upstream sets the pixel clock to 340MHz now, do not set it to 600MHz any more. bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch Fixes: 89956c653252 ("kernel: bump 5.10 to 5.10.138") Fixes: 4209c33ae27d ("kernel: bump 5.10 to 5.10.137") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mbedtls: update to version 2.28.1Hauke Mehrtens2022-08-283-24/+46
| | | | | | | | | | | | Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.1 This release of Mbed TLS provides bug fixes and minor enhancements. This release includes fixes for security issues. The build problem was reported upstream: https://github.com/Mbed-TLS/mbedtls/issues/6243 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit f3870546a544c39c6fde2e7e014394aa085d8057)
* Revert "mediatek: mt7622: fix banana pi r64 wps button"Petr Štetiar2022-08-281-40/+0
| | | | | | | | This reverts commit 5a81e0006380c301cdc691838f519275fc6c28d2 as it was backported upstream in commit a1e238690916 ("arm64: dts: mt7622: fix BPI-R64 WPS button"). Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.10 to 5.10.138John Audia2022-08-286-10/+10
| | | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit fc89ec06928469021010c2f5776450f739af07a5)
* kernel: bump 5.10 to 5.10.137Petr Štetiar2022-08-2822-38/+38
| | | | | | | | | | | Removed following upstreamed patch: * bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch All other patches automagically rebased. Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit d1163fd13f6498826d202f0b58cedf32d7891d52)
* iptables: default to ip(6)tables-nft when using buildrootEtienne Champetier2022-08-281-2/+2
| | | | | | | | | 35fec487e30f05c81bd135326a993dad7f861812 fixed opkg usage, but when using buildroot we were still defaulting to ip(6)tables-legacy Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com> (cherry picked from commit 0c8d7e34ab35f6b41f034fd94fec740970e0125b)
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-08-266-63/+68
| | | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 4807bd6a00bcf44dd821047db76a2a799f403cd4)
* hostapd: fix WPA3 enterprise keys and ciphersJoerg Werner2022-08-261-3/+10
| | | | | | | | | WPA3 enterprise requires group_mgmt_cipher=BIP-GMAC-256 and if 802.11r is active also wpa_key_mgmt FT-EAP-SHA384. This commit also requires corresponding changes in netifd. Signed-off-by: Joerg Werner <schreibubi@gmail.com> (cherry picked from commit 9fbb76c0470fd54f1f34909b1098d0f76078878f)
* iwinfo: update to latest HEADHauke Mehrtens2022-08-261-3/+3
| | | | | | | 0dad3e6 Add support for CCMP-256 and GCMP-256 ciphers Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit cc6a323e2328176b732b13f1f09745354270cd39)
* iproute2: Fix KERNEL_INCLUDE in SDKHauke Mehrtens2022-08-261-1/+1
| | | | | | | | | | | | | | | | | | In the SDK the folder $(LINUX_DIR)/user_headers/include does not exist, but it more or less contains the same content as $(LINUX_DIR)/include/uapi which also exists in the SDK. Since iproute2 commit 1d819dcc741e ("configure: fix parsing issue on include_dir option") it checks if this folder exists and aborts the build if it does not exists. https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/commit/?id=1d819dcc741e25958190e31f8186c940713fa0a8 With this commit the KERNEL_INCLUDE variable points to a valid folder with the kernel include headers. I am not sure if they are actually needed because the build worked before even with an invalid path. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 60738fedede1746922a8b227f24ad5c733661585)
* umbim: bump to git HEADHauke Mehrtens2022-08-261-3/+3
| | | | | | | 146bc77 umbim: fix invalid mbim message string encoding Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 90bedc411b1e98e9adf668dde09f8eafe4490344)
* mt76: update to the latest versionFelix Fietkau2022-08-261-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | 9485e3b47066 mt76: remove q->qid e5674c4aa402 mt76: mt7921: enable HW beacon filter not depending on PM flag 7fd299e3c921 mt76: mt7921: enable HW beacon filter in the initialization stage d5459efaaf14 mt76: mt7921: make mt7921_pci_driver static b8304b456e23 mt76: connac: move tx initialization/cleanup in mt76_connac module 6e0d7077486c mt76: mt7921: reduce log severity levels for informative messages cb80da974fe6 mt76: mt7921: reduce the mutex lock scope during reset a2d61f4f4063 mt76: mt7915 add ht mpdu density 08ea730c1130 mt76: add len parameter to __mt76_mcu_msg_alloc signature 60ef85fa352c mt76: introduce MT_RXQ_BAND2 and MT_RXQ_BAND2_WA in mt76_rxq_id 8ccbb38ca6e6 mt76: add phy_idx in mt76_rx_status eb19ac83c07e mt76: introduce phys array in mt76_dev structure 30887591e3ab mt76: add phy_idx to mt76_wcid 4bf8c20a9524 mt76: convert MT_TX_HW_QUEUE_EXT_PHY to MT_TX_HW_QUEUE_PHY e6c6bf8cee09 mt76: get rid of mt76_wcid_hw routine 120f73ad992a mediatek: mt76: mac80211: Fix missing of_node_put() in mt76_led_init() 111e92cf8c22 mediatek: mt76: eeprom: fix missing of_node_put() in mt76_find_power_limits_node() 13bedd62ff4a mt76: connac: introduce mt76_connac_reg_map structure 5ec78e1ec43d wifi: mt76: fix reading current per-tid starting sequence number for aggregation Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit ec7d32f3769fbd815f72a7471e4bb7a07aee359d)
* netifd: update to the latest versionFelix Fietkau2022-08-251-3/+3
| | | | | | | 76d2d41b7355 interface: fix use-after-free bug when rewriting resolv.conf Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 31648c4b59add5b1cb441073a46c80ab768b588c)
* netifd: update to git HEADHauke Mehrtens2022-08-251-3/+3
| | | | | | | | 87fbefd interface: support "zone" config option bfa039c netifd: fix WPA3 enterprise ciphers Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry-picked from commit 8008816a2ceeb7e66d27d9882685933bb9df4c76)
* rpcd: bump version to 2022-08-24Petr Štetiar2022-08-251-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | gcc 10 with -O2 reports following: In function ‘strncpy’, inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:244:4: /usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation] 106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest)); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ In function ‘strncpy’, inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:227:4: /usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation] 106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest)); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Since it is not possible to avoid truncation by strncpy, it is necessary to make sure the result of strncpy is properly NUL-terminated and the NUL must be inserted explicitly, after strncpy has returned. References: #10442 Reported-by: Alexey Smirnov <s.alexey@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 34ddd2e545f068e4684ecce98c1da3a6c7c9b04a)
* rpcd: update to latest Git HEADJo-Philipp Wich2022-08-251-3/+3
| | | | | | | ae5afea ucode: parse ucode plugin scripts in raw mode, init search path Signed-off-by: Jo-Philipp Wich <jo@mein.io> (backported from commit 66a360206e341abdd1e5560e9cb522d8e453b095)
* uhttpd: update to latest Git HEADJo-Philipp Wich2022-08-251-3/+3
| | | | | | | | | | | | | e3395cd ucode: initialize search path before VM init 8cb3f85 ucode: initialize default library search path 188dea2 utils: accept '?' as path terminator in uh_path_match() c5eac5d file: support using dynamic script handlers as error pages 290ff88 relay: trigger close if in header read state with pending data f9db538 ucode: ignore exit exceptions 8ba0b64 cmake: use variables and find_library for dependency Signed-off-by: Jo-Philipp Wich <jo@mein.io> (backported from commit 4ee77cfcfadcd2b28678a1f3e8e78383b0b21963)
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 18:49:54 +0000