aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.4 to 5.4.109John Audia2021-04-0257-182/+182
| | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: pending-5.4/611-netfilter_match_bypass_default_table.patch The upstream change affecting this patch is the revert of an earlier kernel commit. Therefore, we just revert our corresponding changes in [1]. Build system: x86_64 Build-tested: ipq806x/R7800 [1] 9b1b89229f0e ("kernel: bump 5.4 to 5.4.86") Signed-off-by: John Audia <graysky@archlinux.us> [adjust manually rebased patch, add explanation] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: enhance support for Linksys EA9500Vivek Unune2021-04-014-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add leds and configs 2. Add network configs 3. Add script to clear partial boot flag 4. Hack to use port 5 as cpu port as port 8 connected to eth2 wont pass any frames 5. Enable EA9500 image generation Hardware Info: - Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz - Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 - DDR3 RAM - 256 MB - Flash - 128 MB (Toshiba TC58BVG0S3HTA00) - 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) - 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch - Ports - 8 Ports, 1 WAN Ports - Antennas - 8 Antennas - Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1 Flashing Instructions: 1. Connect a USB-TTL table to J6 on the router as well as a ethernet cable to a lan port and your PC. 2. Power-on the router. 3. Use putty or a serial port program to view the terminal. Hit Ctrl+C and interrupt the CFE terminal terminal. 4. Setup a TFTP server on your local machine at setup you local IP to 192.168.1.2 5. Start the TFTP Server 6. Run following commands at the CFE terminal flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2 nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit 7. Reboot router to be presented by OpenWrt Note: Only installation method via serial cable is supported at the moment. The trx firmware has to be flashed to both the partitions using following commands from CFE prompt. This will cover US and Non-US variants. Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use upstream Linksys EA9500 fixesRafał Miłecki2021-04-012-1/+30
| | | | | | One fix was accepted, one was added. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firewall4: update to latest Git HEADJo-Philipp Wich2021-04-011-3/+3
| | | | | | | | | | | | | 29fba84 tests: expand testing 6bf82a8 fw4.uc: fix family test functions 25b2c7d fw4.uc: fix parsing boolean "0" values 694d428 rule.uc: fix redundant whitespace in rules without target 7f69fbb ruleset.uc: reduce empty lines in output 8f8e42c fw4.uc: gracefully handle missing defaults section 25287af treewide: remove ucode module preloading 802b685 fw4.uc: remove upvalue caching Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ucode: update to latest Git HEADJo-Philipp Wich2021-04-011-3/+3
| | | | | | | | 973cc6c compiler: actually expand block scope fix to for/while alt syntax 97bf297 compiler: ensure that alternative if/for/while syntax has own block scope f0e2a64 tests: add missing test case for fixed switch codegen Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uboot-mediatek: adapt root= cmdline arg for bpi-r64Daniel Golle2021-03-311-2/+2
| | | | | | Adapt to FIT partition parser changes. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: fix FIT partition parser compatibility issuesDaniel Golle2021-03-312-65/+18
| | | | | | | | | | | | The uImage.FIT partition parser used to squeeze in FIT partitions in the range where partition editor tools (fdisk and such) expect the regular partition. This is confusing people and tools when adding additional partitions on top of the partition used for OpenWrt's uImage.FIT. Instead of squeezing in the additional partitions, rather start with all uImage.FIT partitions at offset 64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm4908: backport DT patch adding Ethernet MAC addressRafał Miłecki2021-03-311-0/+82
| | | | | | | This tells OS (Linux) where from MAC should be read (bootloader MTD partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: mt7622: improve sysupgrade on MMCDaniel Golle2021-03-311-49/+12
| | | | | | | Use generic functions to acquire rootdev. Make sure to wipe rootfs_data in case of '-n'. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* base-files: functions: introduce new helper functionsDaniel Golle2021-03-312-63/+68
| | | | | | | | | | | Introduce cmdline_get_var() to /lib/function.sh and make use of it in export_rootdev() in /lib/upgrade/common.sh, making the code more simple and removing one level of indentation. Introduce get_partition_by_name() to /lib/upgrade/common.sh which is useful on non-EFI GPT platforms like mt7622. Remove some dead-code while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bmips: backport pinctrl fixesÁlvaro Fernández Rojas2021-03-312-0/+82
| | | | | | Backport some minor upstream fixes for the pinctrl drivers. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* netifd: update to git HEADDaniel Golle2021-03-311-3/+3
| | | | | | | | | | 09632d4 device: remove left-over comment b22f83d handler: add mechanism to generate external device handler stubs 80bf9d7 extdev: add support for external device handlers 44c0f40 system-linux: reorder sysctl functions c84f3b0 system-linux: add device options used by wpad Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7620: ralink-i2s: fix modpost errorIlya Lipnitskiy2021-03-311-1/+2
| | | | | | | | Fixes the following error when building without CONFIG_MODULE_STRIPPED: FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct of_device_id is not terminated with a NULL entry! Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips/mt7621: enable support for cpuidleRui Salvaterra2021-03-311-1/+9
| | | | | | | | | | | MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support deep sleep idle states and have a specific cpuidle driver for them. Enable support for it, while also switching from constant timer ticks to the idle dynticks model, with the TEO governor. Run-tested on a Redmi AC2100. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips/mt7621: drop the timer recalibration patchRui Salvaterra2021-03-313-97/+10
| | | | | | | | | | | | | | | | | We've been carrying this patch for many years [1], in order to fix a timer calibration issue on MT7621. Turns out, after retesting with a recent kernel (Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls or inconsistent BogoMIPS values across CPUs). Manually refreshed: 322-mt7621-fix-cpu-clk-add-clkdev.patch 323-mt7621-memory-detect.patch [1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Tested-by: Donald Hoskins <grommish@gmail.com> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips/mt7621: drop the weak reordering patchRui Salvaterra2021-03-312-12/+2
| | | | | | | | | | | | | | | | | | In order to fix random hangs on MT7621, we've been selecting WEAK_REORDERING_BEYOND_LLSC for years [1]. However, these random hangs have been most likely caused by an oversight in the MIPS implementation of the kernel memory consistency model, which has already been fixed for some time (and backported to stable) [2]. Manually refreshed: 321-mt7621-timer.patch [1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=5c971cd6fdd7298a2017bdb6bea870088eddb8b9 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/mips?h=linux-5.4.y&id=42344113ba7a1ed7b5654cd5270af0d5698d8521 Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Tested-by: Donald Hoskins <grommish@gmail.com> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* firewall: update to latest git HEADHans Dedecker2021-03-301-3/+3
| | | | | | | a4355a6 firewall3: clean up the flow table detection logic edd0dc5 firewall3: create a common helper to find strings in files Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ncurses: add screen-256color terminfoPaul Spooren2021-03-291-1/+2
| | | | | | | The terminfo is required by the popular terminal multiplexer screen and tmux, offer it by default as the size impact is minimal with 885 Bytes. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ncurses: split long line of supported terminfoPaul Spooren2021-03-291-1/+12
| | | | | | | The terminfo files were all in one row which is terrible to read. Split them over multiple lines to improve readability. Signed-off-by: Paul Spooren <mail@aparcar.org>
* sunxi: enable wifi module on Pine64 boardsZoltan HERPAI2021-03-292-0/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi module, carrying an RTL8723BS. The wifi part is connected via SDIO, the BT part is connected via UART. The BT part requires additional code changes in the drivers so we'll skip that until 5.10. Aside from a DTS patch to enable the wifi module, add the required packages into the device definitions. [ 8.996970] RTL8723BS: module init start [ 9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40 [ 9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40 [ 9.014785] pnetdev = 000000009bdd5000 [ 9.047780] RTL8723BS: rtw_ndev_init(wlan0) [ 9.053349] RTL8723BS: module init ret =0 root@OpenWrt:/# iw list Wiphy phy0 wiphy index: 0 max # scan SSIDs: 9 max scan IEs length: 2304 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * monitor Band 1: Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (no IR) * 2472 MHz [13] (20.0 dBm) (no IR) * 2484 MHz [14] (20.0 dBm) (no IR) Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sunxi: enable MUSB in A53 subtargetZoltan HERPAI2021-03-291-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | The Pine64(+) and the SoPine64 baseboard has two USB ports. One of these (the lower) is connected directly to a USB host, the other one's (upper) PHY is shared with the separate OTG controller. In order to get it working, MUSB support needs to be enabled. As there are other targets which compile MUSB support into the kernel and not package it into modules, the same is done here. [ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.364250] usb usb5: Product: MUSB HDRC host driver [ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd [ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto [ 1.379891] hub 5-0:1.0: USB hub found [ 1.383677] hub 5-0:1.0: 1 port detected [...] [ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00 [ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 697.477180] usb 1-1: Product: USB Flash Disk Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* bmips: dts: align LEDsÁlvaro Fernández Rojas2021-03-296-32/+45
| | | | | | Align all bmips devices LED configurations. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: backport accepted pinctrl patchesÁlvaro Fernández Rojas2021-03-2939-2892/+3446
| | | | | | | These patches have been accepted for linux v5.13. External interrupts not supported for now. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: vr-3032u: fix gpio keysÁlvaro Fernández Rojas2021-03-291-2/+2
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700-v2: fix gpio keysÁlvaro Fernández Rojas2021-03-291-9/+9
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ucode: update to latest Git HEADJo-Philipp Wich2021-03-291-3/+3
| | | | | | | | | | | | | | | | | | | aa9621d compiler: rework switch statement code generation b5f0de1 vm: add trace mode instruction dump output fixes 0341d64 vm: fix another for-loop memory leak 00d9419 vm: fix further memory leaks in trace mode 20a3763 vm: fix loop variable memory leak in NEXTK/NEXTKV instruction 9a6ef2b lib: prevent use-after-free after uc_shift() 03f1324 object: free prototype object when registering existing ressource type b3d758b compiler: fix for/break miscompilation 86e3970 lib: fix value refcount of uc_unshift() return value fe464ea run_tests.sh: allow passing tests to run as arguments 091ae1b compiler: fix another try/catch miscompilation fcedb19 lib: fix passing uninitialized memory to sigprocmask() 0d0357d vm: fix leaking source context strings in trace mode 7a41fb3 lib: use execvp() in system() Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* bcm53xx: fix Linksys EA9500 partitionsRafał Miłecki2021-03-291-0/+58
| | | | | | Use proper DT binding. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport 5.13 mtd partitioning changesRafał Miłecki2021-03-2926-44/+629
| | | | | | | | 1. Use upstream accepted NVMEM patches 2. Minor fix for BCM4908 partitioning 3. Support for Linksys firmware partitions on Northstar Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mac80211: merge a few pending tx related fixesFelix Fietkau2021-03-283-0/+142
| | | | | | Improve performance and fix potential mgmt tx hangs/warnings Signed-off-by: Felix Fietkau <nbd@nbd.name>
* firewall3: update to latest git HEADTony Ambardar2021-03-271-3/+3
| | | | | | | | | | | | | | | This includes several improvements and fixes: 61db17e rules: fix device and chain usage for DSCP/MARK targets 7b844f4 zone: avoid duplicates in devices list c2c72c6 firewall3: remove last remaining sprintf() 12f6f14 iptables: fix serializing multiple weekdays 00f27ab firewall3: fix duplicate defaults section detection e8f2d8f ipsets: allow blank/commented lines with loadfile 8c2f9fa fw3: zones: limit zone names to 11 bytes 78d52a2 options: fix parsing of boolean attributes Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* mvebu: Fix mac addresses for GL.iNet GL-MV1000Sven Eckelmann2021-03-271-0/+4
| | | | | | | | | | | | | The original GL.iNet firmware has two different mac addresses in the factory/art partition. The first one is for the WAN interface only and the second one is for both lan0 and lan1. But the original submission for OpenWrt didn't initialize the mac addresses of the LAN ports for the DSA device at all. The ethernet mac address was then used for all DSA ports. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ramips: correct switch config of Youku yk1Shiji Yang2021-03-271-1/+4
| | | | | | | | | | There are only two lan ports and one wan port on Youku yk1 Fixes: e9baf8265bb8 ("ramips: add support for Youku YK1") Signed-off-by: Shiji Yang <yangshiji66@qq.com> [add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.108John Audia2021-03-2717-40/+33
| | | | | | | | | | | | | | | | | All modifications made by by update_kernel.sh. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 [only 5.4.107] No dmesg regressions, everything functional Run-tested by @timocapa: - ramips/mt7621/{Xiaomi R3G, Redmi 2100} - Lantiq/XWAY/Fritz!Box 7320/7330 Signed-off-by: John Audia <graysky@archlinux.us> [squash, edit commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix label_mac for NEC Aterm WG1200CRINAGAKI Hiroshi2021-03-271-2/+6
| | | | | | | | | | On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label on the case, not LAN. This patch fixes this issue. Fixes: 50fdc0374b ("ath79: provide label MAC address") Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mvebu: Add button support for GL.iNet GL-MV1000Sven Eckelmann2021-03-271-0/+17
| | | | | | | | | | | | | The original patch to support this device advertised support for the reset button and the "switch" in the commit message. But neither were actually integrated in the device tree or documented anywere. The button itself is now used to trigger a reset (as described in the official GL.iNet documentation). The switch itself is registered as BTN_0 like other devices from GL.iNet in ath79. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* kernel: Move CONFIG_USERIO to generic configHauke Mehrtens2021-03-2715-13/+2
| | | | | | | | The CONFIG_USERIO option is unset in multiple target configurations. On the sunxi target it is activated. Move the kernel configuration option to the generic kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Deactivate CONFIG_VFIO in generic kernel configHauke Mehrtens2021-03-274-3/+1
| | | | | | | | | Instead of deactivating this in every target config, deactivate it once in the generic kernel config. I was asked for this config option in a x86 64 build in OpenWrt 21.02. Fixes: 87046e87e229 ("kernel: add missing kernel config symbol") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: add missing kernel config symbolKevin Darbyshire-Bryant2021-03-271-0/+1
| | | | | | | | | | | | Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus malta (at least) prompted for this new symbol. Set it to 'false' in the default config. rockchip & X86 enable it in target specific configs. Thanks to Tony Ambardar for falling over this one Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mt76: update to the latest versionFelix Fietkau2021-03-261-3/+3
| | | | | | | | | | | | | | | | | | | | | 6886b57a1534 mt76: connac: introcuce mt76_sta_cmd_info data structure e529e8afe22a mt76: mt7921: properly configure rcpi adding a sta to the fw e4d522776804 mt76: mt7921: fix airtime reporting be2f67e8d3cb mt76: mt7915: fix key set/delete issue 09a1befde4b7 mt76: fix potential DMA mapping leak f66f8f41d47b mt76: mt7915: refresh repeater entry MAC address when setting BSSID 035e2f6f1ddf mt76: mt7921: get rid of mt7921_mac_wtbl_lmac_addr ee29cd5f3a6a mt76: mt7615: only enable DFS test knobs for mt7615 9a98b1a6f9c2 mt76: mt7615: cleanup mcu tx queue in mt7615_dma_reset() 3bd285424e7b mt76: mt7622: trigger hif interrupt for system reset bf6d9ee4acd1 mt76: mt7615: keep mcu_add_bss_info enabled till interface removal 115b74282314 mt76: mt7915: keep mcu_add_bss_info enabled till interface removal 57432e701d1a mt76: mt7915: cleanup mcu tx queue in mt7915_dma_reset() a519c49a6a42 mt76: mt7615: 0-terminate firmware log messages 4a22f2ffae2e mt76: mt7915: 0-terminate firmware log messages b8609066893a mt76: mt7615: fix chip reset on MT7622 and MT7663e Signed-off-by: Felix Fietkau <nbd@nbd.name>
* x86/base-files: add support for Sophos SG/XG-105Stan Grishin2021-03-262-0/+11
| | | | | | | This adds detection of the Sophos SG-105 and Sophos XG-105 models and assignment of ethernet ports these models have to LAN/WAN. Signed-off-by: Stan Grishin <stangri@melmac.net>
* openssl: bump to 1.1.1kEneas U de Queiroz2021-03-262-25/+24
| | | | | | | | | | | | This version fixes 2 security vulnerabilities, among other changes: - CVE-2021-3450: problem with verifying a certificate chain when using the X509_V_FLAG_X509_STRICT flag. - CVE-2021-3449: OpenSSL TLS server may crash if sent a maliciously crafted renegotiation ClientHello message from a client. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* README: add install command to build requirementsPetr Štetiar2021-03-261-2/+2
| | | | | | | | In commit 8c8496435a9d ("build: add GNU install to prerequisites") new dependency was added, but addition to README was omitted. Fixes: 8c8496435a9d ("build: add GNU install to prerequisites") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "openssl: refresh patches"Kevin Darbyshire-Bryant2021-03-2611-2498/+180
| | | | | | This reverts commit e27ef2da0d513494c3e9926ce8d44b63e4236a32. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* openssl: refresh patchesKevin Darbyshire-Bryant2021-03-2611-180/+2498
| | | | | | Tidy up some patch fuzz. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* elfutils: enable building with MIPS16Tony Ambardar2021-03-251-2/+2
| | | | | | | | | | | | | | | | | | Building with MIPS16 was disabled in 2013 due to an issue with GCC TLS: https://dev.archive.openwrt.org/ticket/13572. But after the problematic GCC version was retired, this change wasn't revisited. Re-enable MIPS16 builds to reduce average elfutils library sizes ~10%. This was compile-tested on malta/mips32be and malta/mips32le, and linked with iproute2 for run-testing. Package sizes follow: Library MIPS16:=0 MIPS16:=1 ------- --------- --------- libelf1 43217 37492 libasm1 12481 11658 libdw1 229723 205793 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel: bump 5.10 to 5.10.26Rui Salvaterra2021-03-264-14/+7
| | | | | | | | | | | | | | Automatically refreshed: ath79/patches-5.10/471-mtd-cfi_cmdset_0002-AMD-chip-0x2201-write-words.patch bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch generic/hack-5.10/204-module_strip.patch Run-tested: ath79 (TL-WDR3600) x86_64 (APU2 - ldir) Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* build,json: 3rd fixup of default_packagesPaul Spooren2021-03-251-18/+5
| | | | | | | | | | | | | | | | | | | | This became a bit of a tragedy, caused by a corner cases which wasn't put into account during testing. DEFAULT_PACKAGES are defined in target/linux/<target>/Makefile but also in target/linux/<target>/<subtarget>/target.mk. The latter was no longer imported when using DUMP=1, however not using DUMP=1 while running the Makefile in target/linux/<target>/ caused duplicate packages in the list. As a solution, which should have been used from day 0, `make` runs in target/linux/ without DUMP=1, resulting in no duplicate packages and all inclusions from include/target.mk, linux/target/<target>/{Makefile, <subtarget>/target.mk} While at it, sort the list of default packages. Signed-off-by: Paul Spooren <mail@aparcar.org>
* build,json: fixup fixup of arch_packagesPaul Spooren2021-03-241-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit "1bf2b3fe90 build,json: fixup missing arch_packages" fixes the missing package architecture locally but runs $(TOPDIR)/Makefile rather than a target specific one. While this works on local builds just fine, it causes the buildbots to add garbage to the `arch_packages` variable: cd \"/builder/shared-workdir/build\"; git log --format=%h -1 toolchain > /builder/shared-workdir/build/tmp/.ver_check\ncmp -s /builder/shared-workdir/build/tmp/.ver_check /builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl/stamp/.ver_check || { \\\n\trm -rf /builder/shared-workdir/build/build_dir/target-x86_64_musl /builder/shared-workdir/build/staging_dir/target-x86_64_musl /builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl /builder/shared-workdir/build/build_dir/toolchain-x86_64_gcc-8.4.0_musl; \\\n\tmkdir -p /builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl/stamp; \\\n\tmv /builder/shared-workdir/build/tmp/.ver_check /builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl/stamp/.ver_check; \\\n}\nx86_64 Only the last line contains the desired string. Future investigation should check why the build system prints this to stdout rather than stderr. Signed-off-by: Paul Spooren <mail@aparcar.org>
* build: add GNU install to prerequisitesKevin Darbyshire-Bryant2021-03-241-0/+4
| | | | | | | | | | | | | | | | The recent removal of usbutils from core and replacement by hwdata in packages has exposed hwdata's requirement for certain GNU options on 'install' (-T) Other packages (sqm-scripts) have openwrt specific makefile sections to avoid GNU options but I suspect this is going to get harder in the future. Add GNU install as a prerequisite and link into $STAGING_DIR/host/etc/bin as per similar GNU utils This resolves an issue building under MacOS which would otherwise use a non-GNU options aware version of 'install' Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* build: make sure asm gets built with -DPICPhilip Prindeville2021-03-241-3/+3
| | | | | | | | | | | | | | | | | Fixes issue openwrt/packages#14921, whereby inline ASM wasn't getting built as PIC; look at gmp-6.2.1/mpn/x86/pentium/popcount.asm for example: ifdef(`PIC',` ... for a routine that exists in both PIC and non-PIC versions. Make sure that wherever $(FPIC) gets passed as a variable expansion that it gets quoted where necessary (such as setting environment variables in shell commands). Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 07:49:00 +0000