| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
97bcdcf uxc: fix segfault caused by use-after-free
6398e05 uxc: don't free the stack
324ebd0 jail: fs: add support for asymmetric mount bind
c44ab7f jail: netifd: generate netifd uci config and mount it
82dd390 jail: make use of per-container netifd via ubus
The new per-jail netifd is now configured by filtering the host
network configuration. As libuci is used for that, procd-ujail now
depends on libuci.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
| |
be8cd8f interface: don't fork() to start jail interface
7a048bd interface, ubus: rework netns up/down
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
| |
83598c2e872f mt76: avoid possible infinite loop in mt76_tx_status_check
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
1af0242d1241 mt76: mt7915: replace a 64 bit divsion with a call to div_u64_rem
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Our backports version does not have support for kcov in mac80211
Fixes build errors on some platforms
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
74dedf9352c5 mt76: mt7615: fix skb use-after-free on mac reset
7201290eda43 mt76: mt7921: Fix out of order process by invalid event pkt
ca1b57e9971a mt76: mt7915: add a missing HT flag for GI parsing
4932c5d80153 of: net: pass the dst buffer to of_get_mac_address()
51d9eb3e6f52 mt76: mt7915: fix endianness warnings in mu radiotap
833ca13014ab mt76: mt7921: Add mt7922 support
8f8ed44d026e mt76: mt7915: add control knobs for thermal throttling
16f18bab6b11 mt76: mt7915: send EAPOL frames at lowest rate
affea639c586 mt76: mt7921: send EAPOL frames at lowest rate
ac00fed412d4 mt76: mt7915: fix potential overflow of eeprom page index [update]
e576ddb76dfa mt76: mt7915: switch proper tx arbiter mode in testmode
222847c3d5eb mt76: mt7915: fix bit fields for HT rate idx
d04814366c83 mt76: add support for setting mcast rate
4602acc9271a mt76: mt7921: fix dma hang in rmmod
ec2cf3bf96fd mt76: connac: fix GTK rekey offload failure on WPA mixed mode
2fdb9d621431 mt76: connac: add support for limiting to maximum regulatory Tx power
489ace63d42c mt76: mt7921: get rid of monitor_vif
22da8d28fcc8 mt76: mt7921: get rid of mt7921_mac_set_beacon_filter
c94130519786 mt76: mt7921: introduce mt7921_mcu_set_beacon_filter utility routine
51cff39d7ad3 mt76: overwrite default reg_ops if necessary
da11c1c6edef mt76: mt7615: move mt7615_mcu_set_p2p_oppps in mt76_connac module
47f50b0aa4b8 mt76: mt7921: report HE MU radiotap
4f48ba4b0254 mt76: mt7915: checkpatch cleanup
bc7ee7d7bdea mt76: mt7915: add HE-LTF into fixed rate command
6a19e40820aa mt76: mt7921: continue to probe driver when fw already downloaded
8b3d8e2de084 mt76: mt7921: fix firmware usage of RA info using legacy rates
17305a54b166 mt76: mt7921: fix kernel warning from cfg80211_calculate_bitrate
801c15577293 mt76: mt7921: fix endianness warnings in mt7921_mac_decode_he_mu_radiotap
0182a5b99a7a mt76: mt7915: update mac timing settings
e2ee9d0a33ed mt76: use IEEE80211_OFFLOAD_ENCAP_ENABLED instead of MT_DRV_AMSDU_OFFLOAD
fa6504aceb4f Revert "mt76: mt7915: checkpatch cleanup"
56b842b72a72 mt76: mt7915: fix wmm index on DBDC cards
8044311f5de5 mt76: mt7915: fix potential NPE in TXS processing
28da4baec7c5 mt76: mt7915: fix he_mcs capabilities for 160mhz
f7088ebe7452 mt76: mt7915: add LED support
ee019046284d mt76: mt7915: introduce bss coloring support
9848094e4bb5 mt76: mt7921: Fix fall-through warning for Clang
5710d0643418 mt76: add a bound check in mt76_calculate_default_rate()
a509cf2b654e mt76: mt7921: move mt7921_queue_rx_skb to mac.c
5a0f2382fcfe mt76: mt7915: rework debugfs queue info
62ffc31f4d7b mt76: mt7915: rename debugfs tx-queues
4750b5c918e5 mt76: mt7921: always wake device if necessary in debugfs
ac6adf74b3f2 mt76: mt7921: update mib counters dumping phy stats
eb75b9266ce6 net:wireless:mt76: fix boolreturn.cocci warnings
d7c4698435b3 mt76: mt7921: fix the inconsistent state between bind and unbind
9dcfba3169c4 mt76: switch from 'pci_' to 'dma_' API
d8b5e42c9a73 mt76: fill boottime_ns in Rx path
8ee6446075f2 mt76: disable BH around napi_schedule() calls
e17d730bf2f6 mt76: mt7915: add LED support [update to v3]
80fe40c9457e mt76: mt7915: enable configured beacon tx rate
c8f0d1d81d05 mt76: mt7915: fix hwmon temp sensor mem use-after-free
3b9ba7e02076 mt76: mt7615: fix hwmon temp sensor mem use-after-free
5e82eceb45cb mt76: mt7921: start reworking tx rate reporting
eb66b5c9ff77 mt76: mt7921: add support for tx status reporting
c8010f170e76 mt76: mt7921: report tx rate directly from tx status
4dc7f3db572b mt76: mt7921: remove mcu rate reporting code
db89c6f86724 mt76: mt7921: remove mt7921_sta_stats
6bb8b4267dbe mt76: move spin_lock_bh to spin_lock in tasklet
0eacf41985da mt76: mt7915: honor all possible error conditions in mt7915_mcu_init()
4dfff296ee6e mt76: mt7915: fix possible infinite loop release semaphore
537ed88dd2d0 mt76: mt7921: robustify hardware initialization flow
e0b846159221 mt76: mt7921: fix retrying release semaphore without end
c55dedcea268 mt76: mt7915: add ethtool stats support
d1d5e8cd3a3e mt76: mt7915: add tx stats gathered from tx-status callbacks
1687189d68b7 mt76: mt7915: add some per-station tx stats to ethtool
f4dde5f765af mt76: mt7915: add tx mu/su counters to mib
9752bf0643c9 mt76: mt7915: add more MIB registers
4727415017c9 mt76: mt7915: add mib counters to ethtool stats
4ca80a749e7f mt76: connac: set 6G phymode in mt76_connac_get_phy_mode{,v2}
3f2a5d39631e mt76: connac: enable 6GHz band for hw scan
817a41826bd7 mt76: connac: add 6GHz support to mt76_connac_mcu_set_channel_domain
a6ab81c21080 mt76: connac: set 6G phymode in single-sku support
ca4f47028a44 mt76: connac: add 6GHz support to mt76_connac_mcu_sta_tlv
d2e192ea81e2 mt76: connac: add 6GHz support to mt76_connac_mcu_uni_add_bss
c3dd12b4c8ae mt76: connac: enable hw amsdu @ 6GHz
91ed2b256c20 mt76: add 6GHz support
de8c4f92621f mt76: mt7921: add 6GHz support
f143aedc1d57 mt76: introduce packet_id idr
bcc8d9e03a5d mt76: remove mt76_wcid pointer from mt76_tx_status_check signature
ccbd84763153 mt76: substitute sk_buff_head status_list with spinlock_t status_lock
69bb59df894c mt76: schedule status timeout at dma completion
03a992645310 mt76: support reading EEPROM data embedded in fdt
75615480b3fe mt76: introduce __mt76_mcu_send_firmware routine
e8e2eae41f94 mt76: drop MCU header size from buffer size in __mt76_mcu_send_firmware
4c455e8b1a20 mt76: mt7915: introduce __mt7915_get_tsf routine
9d49c611a2d7 mt76: mt7915: introduce mt7915_mcu_twt_agrt_update mcu command
f44ca79c9aed mt76: mt7915: introduce mt7915_mac_add_twt_setup routine
2f9555a2f18f mt76: mt7915: enable twt responder capability
440e2db8d541 mt76: mt7915: add twt_stats knob in debugfs
eb5f640f8afa mt76: debugfs: improve queue node readability
53d7eb3b4884 mt76: mt7615: fix monitor mode tear down crash
2aa3d4414826 mt76: mt7921: add delay config for sched scan
47e8e96e8e4d mt76: use a separate CCMP PN receive counter for management frames
5560b08f8e2d mt76: do not access 802.11 header in ccmp check for 802.3 rx skbs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
Required for an upcoming mt76 update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
Fixes packaging of eBPF modules
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
| |
Refreshed patch.
Disable hiredis backend since it seems to default to it now.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit f536f5ebddd9c532a08ac4a9be3ef0c02f7bfeb8.
As Hauke commented, this causes builder failures on 5.4 kernels.
This revert includes changes to the mx100 kernel modules
dependency as well as the uci led definitions.
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
The python path cannot be embedded in the meson binary as it changes
with the SDK.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.
While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage
Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.
The gzip compressed version would be 4116k.
[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5a2 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit will add support for the Meraki MX100 in OpenWRT.
Specs:
* CPU: Intel Xeon E3-1200 Series 1.5GHz 2C/4T
* Memory: 4GB DDR3 1600 ECC
* Storage: 1GB USB NAND, 1TB SATA HDD
* Wireless: None
* Wired: 10x 1Gb RJ45, 2x 1Gb SFP
UART:
The UART header is named CONN11 and is found in the
center of the mainboard. The pinout from Pin 1 (marked
with a black triangle) to pin 4 is below:
Pin 1: VCC
Pin 2: TX
Pin 3: RX
Pin 4: GND
Note that VCC is not required for UART on this device.
Booting:
1. Flash/burn one of the images from this repo to a
flash drive.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Hook up UART to the MX100, plug in the USB drive,
and then power up the device.
4. At the BIOS prompt, quickly press F7 and then
scroll to the Save & Exit tab.
5. Scroll down to Boot Override, and select the
UEFI entry for your jumpdrive.
Note: UEFI booting will fail if the SATA cable for
the HDD is plugged in.
The issue is explained under the Flashing instructions.
Flashing:
1. Ensure the MX100 is powered down, and not plugged
into power.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Using the Mini USB female port found by the SATA
port on the motherboard,
flash one of the images to the system. Example:
`dd if=image of=/dev/sdb conv=fdatasync` where sdb
is the USB device for the MX100's NAND.
4. Unplug the Mini USB, hook up UART to the MX100,
and then power up the device.
5. At the BIOS prompt, quickly press F7 and then
scroll to the Boot tab.
6. Change the boot order and set UEFI: USB DISK 2.0
as first, and USB DISK 2.0 as second.
Disable the other boot options.
7. Go to Save & Exit, and then select Save Changes and
Reset
Note that OpenWRT will fail to boot in UEFI mode when
the SATA hard drive is plugged in. To fix this, boot
with the SATA disk unplugged and then run the following
command:
`sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg`
Once the above is ran, OpenWRT will boot when the HDD
is plugged into SATA. The reason this happens is the
UEFI implementation for the MX100 will always set
anything on SATA to HD0 instead of the onboard USB
storage, so we have to accomidate it since OpenWRT's
GRUB does not support detecting a boot disk via UUID.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This adds a userspace interpretation of the nu801 driver used by Meraki
hardware. Previously this was a driver that was added per target, but as
multiple targets now have this driver, we should move to something that
can be shared by all targets since no driver exists upstream.
Co-developed-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
try to reduce the kernel size by disabling and moving
options from the common kernel configuration to the
SATA target that doesn't have the constraints.
For NAND this has become necessary because as with 5.10
some devices outgrew their kernels. Though, in my tests
this didn't help much: just a smidgen over 100kib was
saved on the uncompressed kernel.
... running make kernel_oldconfig also removed some
other config symbols, mostly those that already set
from elsewhere or became obsolete in the meantime.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
| |
disables the MX60(W) from being built by the builders for now.
But there's an effort to bring it back:
<https://github.com/openwrt/openwrt/pull/4617>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
| |
The D-Link DIR-685 has a small screen with a framebuffer
console, so if we have this, when we start, display the
banner on this framebuffer console so the user know they
are running OpenWRT as root filesystem.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Due to 5.10 increased kernel size, the current 4MiB-ish kernel
partition got too small. Luckily, netgear's uboot environment
is setup to read 0x60000 bytes from the kernel partition location.
... While at it: also do some cleanups in the DTS in there.
The original (re-)installation described in
commit d82d84694e60 ("apm821xx: add support for the Netgear WNDAP620 and WNDAP660")
seemed to be still working for now. What I noticed though
is that the bigger initramfs images needed to use a different
destination address (1000000) to prevent it overwriting
itself during decompression. i.e:
# tftp 1000000 openwrt-...-wndap620-initramfs-kernel.bin
# bootm
However, in case of the WNDAP620+660 the factory.img image can be
written directly to the flash through uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
| |
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Both NAND and SATA targets need the DMA engine in one way
or another.
Due to a kernel config refresh various existing symbols
got removed from the apm821xx main config file as well.
(That being said, they are still included because the
built-in crpyto4xx depends on these.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
While the binary `python3.10` is correctly detected by the build system
the default `python3` binary is currently not detected if pointing to a
Python 3.10 installation.
Fix this by extending the grep regex.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
| |
All patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
| |
All patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.
For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This target has testing support for more than half a year now.
Time to switch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Now that we have fully switched to nvmem interface we can drop
the use of mtd-mac-address patches as it's not used anymore and
the new nvmem implementation should be used for any new device.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
LED labels got reversed by accident, so fix it to the usual color:led_name format.
Fixes: 78cf3e53b1f4 ("mvebu: add Globalscale MOCHAbin")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This target has testing support for more than half a year now.
Time to switch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
Linux 5.10 has been there as testing kernel for a while now.
Do the switch and drop config and patches for Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
| |
Enable kernel options to allow loading device tree overlay via configfs
at runtime. This is useful for devboards like the BPi-R2 and BPi-R64
which got RasbPi-compatible 40-pin GPIO header which allow all sorts
of extensions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
| |
The otto GPIO driver does not work with rtl9300 SoCs. Add
the legacy driver again and use that by default in the 9300 .dtsi
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Enables Aquantia PHY support in the kernel
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
|
|
| |
RTL8393 SoCs older than Revision C hang on accesses to PHYs with PHY address
larger or equal to the CPU-port (52). This will make scanning the MDIO bus
hang forever. Since the RTL8390 platform does not support more than
52 PHYs, return -EIO for phy addresses >= 52. Note that the RTL8390 family
of SoCs has a fixed mapping between port number and PHY-address.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Removes unnecessary output from the RTL PHY drivers.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Adds support for debugfs on RTL9300, in particular the drop counters.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
Adds SoC specific routing offload implementations for
RTL8380/90 and RTL9300. RTL83xx supports merely nexthop
routing, RTL9300 full host and prefix routes.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
Add generic support for listening to FIB and Event notifier updates and
use this information to hook into the L3 hardware capabilities of the
RTL SoCs.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
| |
This hack adds support for the Aquantia 4th generation, 10GBit
PHYs AQR113C and AQR813.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
| |
Improve handling of multi-gig ports on the RTL9300 when probing
the MDIO bus.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
|
|
|
| |
The ingress filter registers use 2 bits for each port to define the filtering
state, whereas the egress filter uses 1 bit. So for for the ingress filter
the register offset for a given port is:
(port >> 4) << 4: since there are 16 entries in a register of 32 bits
and for the egress filter:
(port >> 5) << 4: since there are 32 entries in a register of 32 bits
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
Configure a sane L2 learning configuration upon DSA driver load so that the
switch can start learning L2 addresses. Also configure the correct flood masks
for broadcast and unknown unicast traffice.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
This adds RTL93xx-specific MAC configuration routines that allow also configuration
of 10GBit links for phylink. There is support for the Realtek-specific HISGMI
protocol.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Adds the RTL930x-specific PIE support routines.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Adds the RTL839x-specific PIE support routines.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
| |
Adds the RTL838x-specific PIE support routines.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
| |
This adds support for offloading TC flower by using the Packet Inspection Engine
of the RTL-SoCs. Basic infrastructure support is provide with callbacks to the
tc subsystem and support for HW packet counters.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|