aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: 5.10: add patches to fix macronix flashNick Hainke2021-12-293-1/+65
| | | | | | | | | | | | | | | | | | | | | | | mtd: spi-nor: locking support for MX25L6405D Macronix MX25L6405D supports locking with four block-protection bits. Currently, the driver only sets three bits. If the bootloader does not sustain the flash chip in an unlocked state, the flash might be non-writeable. Add the corresponding flag to enable locking support with four bits in the status register. mtd: spi-nor: disable 16-bit-sr for macronix Macronix flash chips seem to consist of only one status register. These chips will not work with the "16-bit Write Status (01h) Command". Disable SNOR_F_HAS_16BIT_SR for all Macronix chips. Refreshed: - 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Signed-off-by: Nick Hainke <vincent@systemli.org>
* utils/px5g-wolfssl: make selfsigned certicates compatible with chromiumSergey V. Lobanov2021-12-292-1/+21
| | | | | | | | | | | | | | Chromium based web-browsers (version >58) checks x509v3 extended attributes. If this check fails then chromium does not allow to click "Proceed to ... (unsafe)" link. This patch add three x509v3 extended attributes to self-signed certificate: 1. SAN (Subject Alternative Name) (DNS Name) = CN (common name) 2. Key Usage = Digital Signature, Non Repudiation, Key Encipherment 3. Extended Key Usage = TLS Web Server Authentication SAN will be added only if CONFIG_WOLFSSL_ALT_NAMES=y Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
* libs/wolfssl: add SAN (Subject Alternative Name) supportSergey V. Lobanov2021-12-292-2/+7
| | | | | | | | | x509v3 SAN extension is required to generate a certificate compatible with chromium-based web browsers (version >58) It can be disabled via unsetting CONFIG_WOLFSSL_ALT_NAMES Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
* ramips: add support for ipTIME A3004TWonJung Kim2021-12-293-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: NAND 128MB (Macronix NAND 128MiB 3,3V 8-bit) - WiFi: - 2.4GHz: MT7615E - 5GHz : MT7615E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: 1. Flash initramfs image using OEM's Recovery mode 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: - Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power up with holding down the reset key until CPU LED stop blinking. 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0` 3. Flash image via tftp to `192.168.0.1` Additional Notes: This router shares one MT7915E chip for both 2.4Ghz/5Ghz. radio0 will not working on 5Ghz as it's not connected to the antenna. Signed-off-by: WonJung Kim <git@won-jung.kim> (added led dt-bindings) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for WeVO AIR DUOSungbo Eo2021-12-293-1/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on MediaTek MT7620A. Specifications: * SoC: MT7620A * RAM: 64 MiB * Flash: SPI NOR 16 MiB * USB & SATA bridge controller: JMicron JMS567 * SATA 6Gb/s: 2.5" drive slot * USB 3.0: Micro-B * USB 2.0: connected to SoC * Wi-Fi: * 2.4 GHz: SoC built-in * 5 GHz: MT7612EN * Ethernet: 5x 1GbE * Switch: MT7530WU * UART: 4-pin 1.27 mm pitch through-hole (57600 baud) * Pinout: (3V3)|(RXD) (TXD) (GND) Notes: * The drive is accessible through the external USB port only when the router is turned off. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. The image filename should have ".upload" extension. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* bcm27xx: add AMP2 to HifiBerry DAC+ / DAC+ Pro packageTorsten Duwe2021-12-291-6/+9
| | | | | | | | | | | | | According to the vendor [1] these HATs share the same DT overlay: hifiberry-dacplus. The PCM512x-compatible control unit is attached to I2C, so the additional snd-soc-pcm512x-i2c kernel module is required. Also explicitly note the Amp2 support to reduce confusion for those users. [1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/> Signed-off-by: Torsten Duwe <duwe@lst.de> (added bcm27xx tag, changed commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kirkwood: add support for two clones from EndianPawel Dembicki2021-12-294-0/+241
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | They are Endian 4i Edge 200 and his clone Endian UTM Mini. Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 512MB (Micron 29F4G08AAC) - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2) - Lan 5: 1x GBE (Marvell 88E1116R-NNC1) - Storage: MicroSD Slot - WLAN: MiniPCIe Slot present, and fitted with SparkLan WPEA-110N/E (Atheros AR9280 chipset) (ONLY Endian UTM Mini WLAN) - USB: 1x USB 2.0 port - Console: RJ-45 port - LEDs: 3x GPIO controlled Notes: - WLAN led (Endian UTM Mini) is drived by MPCIE card Installation by TFTP + serial: - Setup TFTP server and copy initramfs image - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Installation by USB + serial: - Copy initramfs image to fat32 usb drive - Connect pendrive to USB 2.0 front socket - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv usb reset fatload usb 0:1 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: add support for NETGEAR ReadyNAS Duo v2Pawel Dembicki2021-12-2913-2/+601
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC. Specification: - Processor Marvell 88F6282 (1.6 GHz) - 256MB RAM - 128MB NAND - 1x GBE LAN port (PHY: Marvell 88E1318) - 1x USB 2.0 - 2x USB 3.0 - 2x SATA - 3x button - 5x leds - serial on J5 connector accessible from rear panel (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!) Installation by USB + serial: - Copy initramfs image to fat32 usb drive - Connect pendrive to USB 2.0 front socket - Connect serial console - Stop booting in u-boot - Do: usb reset setenv bootargs 'console=ttyS0,115200n8 earlyprintk' setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' saveenv fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Installation by TFTP + serial: - Setup TFTP server and copy initramfs image - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Known issues: - Power button and PHY INTn pin are connected to the same GPIO. It causes that every network restart button is pressed in system. As workaround, button is used as regular BTN_1. For more info please look at file: RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c from Netgear GPL sources. Tested-by: Raylynn Knight <rayknight@me.com> Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: generic: backport linkstation-poweroff driverPawel Dembicki2021-12-294-0/+254
| | | | | | | | | | | Linkstation poweroff driver was added to mvebu target, but is required for kirkwood target too. This commit make two changes: - move linkstation-poweroff support patch from mvebu to generic and replace upstream accepted version - backport small linkstation-poweroff fix from 5.12 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* packages: kernel: add i2c hwmon g762 kmod packagePawel Dembicki2021-12-291-0/+15
| | | | | | | This patch adds kernel module for Global Mixed-mode Technology Inc G762 and G763 fan speed PWM controller chips. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* scripts: dump-target-info print kernel versionsPaul Spooren2021-12-291-3/+23
| | | | | | | | | | | | | | | | | | | | | | | | | This commits adds the ability to print Kernel versions of all targets/subtargets. If a testing Kernel is set print that version as well. Example output: apm821xx/nand 5.10 apm821xx/sata 5.10 arc770/generic 5.4 archs38/generic 5.4 armvirt/32 5.10 armvirt/64 5.10 at91/sam9x 5.10 at91/sama5 5.10 ath25/generic 5.4 ath79/generic 5.4 5.10 ath79/mikrotik 5.4 5.10 --- %< --- This should help to get a quick update on the state of Kernels. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ath79: remove pre-5.10 specific kernel codeDavid Bauer2021-12-295-65/+2
| | | | | | With Kernel 5.4 support removed, we can get rid of this legacy code. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: aw9523: add can_sleep flag for GPIO chipDavid Bauer2021-12-291-1/+1
| | | | | | | | The GPIO expander is connected via I2C, thus the can_sleep flag has to be set to true. This should fix spurious "scheduling while atomic" bugs in the kernel ringbuffer. Signed-off-by: David Bauer <mail@david-bauer.net>
* tfa-layerscape: fix build on systems without openssl headersHauke Mehrtens2021-12-281-1/+2
| | | | | | | | | | | | | | | | | | The build fails when the openssl/sha.h header file is not installed on the host system. Fix this by setting the HOSTCCFLAGS variable to the OpenWrt HOST_CFLAGS variable, without setting this the include paths and other modifications in the host flags done by OpenWrt will be ignored by the build. This fixes the following build problem: gcc -c -D_GNU_SOURCE -D_XOPEN_SOURCE=700 -Wall -Werror -pedantic -std=c99 -O2 -I../../include/tools_share fiptool.c -o fiptool.o In file included from fiptool.h:16, from fiptool.c:19: fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory 19 | # include <openssl/sha.h> | ^~~~~~~~~~~~~~~ Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* layerscape: restool: Remove build of manpagesHauke Mehrtens2021-12-281-0/+18
| | | | | | | | The build of the manpages needs the pandoc tool, this is not in the minimal requirements of OpenWrt, just remove the build of the restool manpage. This fixes the build on systems without pandoc like the OpenWrt build bots. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: yet again, replace patch with updated pending patchDaniel Golle2021-12-272-37/+125
| | | | | | | | | Upon comment of Russell King ('Oh no, not this "-1 disease" again.') clean up mdio read and write return type and value in mtk_eth_soc driver and also use appropriate return values for bus-busy-timeout- errors in newly added Clause 45 access code. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: add fallback for WPS on stationsRaphaël Mélotte2021-12-271-7/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Up to now the WPS script triggered WPS on the stations only if it could not trigger it successfully on any hostapd instance. In a Multi-AP context, there can be a need (to establish a new wireless backhaul link) to trigger WPS on the stations, regardless of whether there is already a hostapd instance configured or not. The current script makes it impossible, as if hostapd is running and configured, WPS would always be triggered on hostapd only. To allow both possibilities, the following changes are made: - Change the "pressed" action to "release", so that we can make use of the "$SEEN" variables (to know for how long the button was pressed). - If the button is pressed for less than 3 seconds, keep the original behavior. - If the button is pressed for 3 seconds or more, trigger WPS on the stations, regardless of the status of any running hostapd instance. - Add comments explaining both behaviors. - While at it, replace the usage of '-a' with a '[] && []' construct (see [1]). This gives users a "fallback" mechanism to onboard a device to a Multi-AP network, even if the device already has a configured hostapd instance running. [1]: https://github.com/koalaman/shellcheck/wiki/SC2166 Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
* mediatek: replace patch with version sent upstreamDaniel Golle2021-12-272-94/+166
| | | | | | | | | Replace recently added patch 701-net-ethernet-mtk_eth_soc-add-support-for-clause-45-mdio.patch with version sent upstream 701-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-access.patch Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath25: add kernel 5.10 supportSergey Ryazanov2021-12-2714-0/+3843
| | | | | | | | | | | | | | | | | | Copy and refresh patches and config from 5.4 to 5.10. Most patches require no more then automatic refresh. The only exception is the Ethernet driver patch, which requires some more work: * drop eth_change_mtu() usage since it was removed from the kernel, it anyway useless for drivers that utilizes alloc_etherdev(); * add the txqueue number argument to the .ndo_tx_timeout callback function; * replace ioremap_nocache() which was finally removed from the kernel by the ioremap() with the same behaviour. Switch target to the new kernel version. Signed-off-by: Daniel Golle <daniel@makrotopia.org> [use KERNEL_TESTING_PATCHVER for now] Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ath25: refresh kernel 5.4 configSergey Ryazanov2021-12-271-54/+2
| | | | | | | | | | | | The target config require some refresh due to the just introduced filtering of the "run-time" options, MIPS eBPF JIT backporting, and so on. The configuration is easily updated using make kernel_oldconfig. So let's update it now in preparation for v5.10 support to reduce the new kernel configuration diff. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* Move mvswitch 88E6060 driver to the ath25Sergey Ryazanov2021-12-276-9/+25
| | | | | | | | | | | | | | | | | | | | | | ath25 requires a 88E6060 driver to support boards such as Fonera 2.0g (FON2202). The swconfig based mvswitch driver has not yet been ported to the 5.10 kernel as the only user is the ath25 target while all other targets have been switched to the upstream DSA implementation. Switching ath25 to the DSA implementation is a complex task, since we need either per-board platform data or DTS support. ath25 lacks both of them and builds only a single generic image. So we need to keep the swconfig driver implementation to easly and quickly port ath25 to the 5.10 kernel. Since porting the mvswitch driver to 5.10 as a generic driver is not an option, and since the ath25 is its only user, make mvswitch a target specific driver to be able to port it to the 5.10 kernel as part of the kernel version update of the target. This will allow us quickly migrate to the next kernel version and not delay the next firmware release. Suggested-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: bump 5.10 to 5.10.88Rui Salvaterra2021-12-277-63/+8
| | | | | | | | | Deleted (upstreamed): mpc85xx/patches-5.10/002-powerpc-85xx-fix-oops-when-CONFIG_FSL_PMC-n.patch [1] [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.88&id=151ffac3ac277ad7c2a5f201b566b56d97ed3a99 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* apm821xx: remove broken PCIe MSI supportChristian Lamparter2021-12-275-41/+0
| | | | | | | | These never worked and upstream is in the process of removing them as well. Legacy PCI interrupt signaling is still working as before. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: remove overlapping partitionsChristian Lamparter2021-12-271-26/+17
| | | | | | | | Apart from the dtb partition, these were all "read-only;" they serve no purpose other than being a copy of what netgear had defined in their original firmware. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix WD MyBook Live DUO USB-PortChristian Lamparter2021-12-272-1/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | where to begin? the USB regulator settings were just a part of the issue. With them changed, according to the forum it still failed when a USB device was connected to the port with: dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers dwc2 4bff80000.usbotg: exit partial_power_down failed dwc2 4bff80000.usbotg: HC died; cleaning up One clue was found upstream in commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices") |Disable power_down by setting the parameter to |DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic |Meson SoCs where USB devices are only recognized when plugged in before |booting Linux. A hot-plugged USB device was not detected even though the |device got power (my USB thumb drive for example has an LED which lit |up). |[...] the same method proposed there worked with APM821xx's USB IP-Core. Link: https://forum.openwrt.org/t/wd-my-book-duo-usb/111926/2 Reported-by: thwe and takimata (openwrt forum) Fixes: b70d3557e05 ("apm821xx: clean up gpio-hogs") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* linux-firmware: amd: consolidate amd's linux-firmware entriesChristian Lamparter2021-12-274-65/+29
| | | | | | | | | | | | this patch consolidates the amd64-microcode (moved to linux-firmware.git, previously this was an extra debian source package download), amdgpu and radeon firmwares into a shared "amd" makefile. With the upcoming 20211216 linux-firmware bump, this will include a microcode update for ZEN 3 CPUs. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* tools/mkimage: update to 2021.10Huangbin Zhan2021-12-276-399/+12
| | | | | | | | | | | | | | Changelog: - upstream now needs OpenSSL in order to be able to sign FITs. See: commit cb9faa6f98ae ("tools: Use a single target-independent config to enable OpenSSL") - removes upstream patches. Link: https://github.com/u-boot/u-boot/commit/cb9faa6f98ae56d70d59505dad290dd3d381cb7b Tested-by: Sergey V. Lobanov <sergey@lobanov.in> Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* umbim: add missing json_close_object callMartin Schiller2021-12-271-0/+1
| | | | | | | | Otherwise, connection setup may fail due to JSON parse error in netifd. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [Updated commit description] Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* umbim: explicitly check for PIN1 stateMartin Schiller2021-12-271-1/+2
| | | | | | | | | | | PIN2 is used only to restrict changing of fixed dialling feature, does not affect network registration. Therefore explicitly check for PIN1 state during connection setup, which is required for network registration. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [Updated commit description] Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* umbim: call umbim disconnect in error caseMartin Schiller2021-12-271-1/+13
| | | | | | | | This is needed to properly close the control channel. Otherwise, on the next try the caps call may fail. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* apm821xx: drop 5.4 config and patchesChristian Lamparter2021-12-2711-1956/+0
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* realtek: netgear-gs110tpp: Add system LEDsSander Vanheule2021-12-271-0/+33
| | | | | | | | The GS110TPP has an RGB LED used for system status indication. Expose all three components as separate GPIO LEDs connected via the device's RTL8231. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: netgear-gigabit: Enable RTL8231Sander Vanheule2021-12-271-2/+4
| | | | | | | | | | | | | | | | Since the move to 5.10, there are now two GPIO drivers. The gpio0 node refers to the internal GPIOs, so the indirect-access-bus-id is no longer relevant for that node. Set indirect-access-bus-id to the correct value (31) on the correct node (gpio1) and enable the device. Cc: Raylynn Knight <rayknight@me.com> Cc: Michael Mohr <akihana@gmail.com> Cc: Stijn Segers <foss@volatilesystems.org> Cc: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Bjørn Mork <bjorn@mork.no>
* kernel: mtd: parsers: add nvmem support to cmdlinepartAnsuel Smith2021-12-272-0/+240
| | | | | | | | | | | | | | | | | | | Assuming cmdlinepart is only one level deep partition scheme and that static partition are also defined in DTS, we can assign an of_node for partition declared from bootargs. The cmdlinepart parser is the first parser checked and if it does find some partition declared in the bootargs, every other parser is ignored. This means that the fixed-partition parser is ignored and an of_node for the mtd is never assigned. Fix this by searching a defined of_node using a similar fixed_partition parsing logig, check if a partition is present with the same label, check that it has the same offset and size and finally assign an of_node to the mtd. The NVMEM can now find the of_node for the mtd and correctly works. Fixes: abc17bf306ac ("ath79: convert mtd-mac-address to nvmem implementation") Tested-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* base-files: upgrade: fix efi partitions size calculationJavier Marcet2021-12-271-1/+1
| | | | | | | | | We were missing (not using) the last sector of each partition, compared with the output of gparted. Signed-off-by: Javier Marcet <javier@marcet.info> [moved the dot] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* toolchain: musl: disable crypt size hack by defaultPetr Štetiar2021-12-271-3/+4
| | | | | | | | | | | | | | | | Enable this option and thus re-include crypt() support for the SHA256, SHA512 and Blowfish ciphers on all devices. According to commit 9365745f8e7b ("musl: add a hack to remove unused crypt() algorithms, saves ~14k after lzma") it should add about ~14k to the resulting image, which seems to be a reasonable size increase for consistent crypt() support. Decided to not remove this hack completely as it might be still useful for people trying to fit custom images onto smaller devices and the patch is rather simple so we can afford to keep it for now. References: https://github.com/openwrt/openwrt/pull/1331 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* rockchip: remove Kernel 5.4David Bauer2021-12-2712-1559/+0
| | | | | | | As v5.10 is the default kernel version now, the files for v5.4 can be dropped. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove kernel 5.4David Bauer2021-12-2710-725/+0
| | | | | | | As v5.10 is the default kernel version now, the files for v5.4 can be dropped. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: remove kernel 5.4David Bauer2021-12-2741-4607/+0
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add missing function declarationDavid Bauer2021-12-271-0/+10
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add missing UBNT_REVISIONNick Hainke2021-12-271-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The UBNT_REVISION was already added for the ubnt-xw target because: U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails ... By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again. commit d42a7c469909 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method") Fixes errors in the form of (tftp flashing): sent DATA <block=8577, 412 bytes> received ERROR <code=2, msg=Firmware check failed> Error code 2: Firmware check failed The missing UBNT_REVISION was not noticed before, since the UBNT_REVISION field for the ubnt-xm target was also set to: "42.OpenWrt-..." Probably, UBNT_REVISION for the ubnt-xm target was set by the ubnt-xw and was never overridden somewhere else. However, it is missing and should be part of the ubnt-xm device. Signed-off-by: Nick Hainke <vincent@systemli.org>
* sunxi: Use rtl8723bu-firmware instead of rtl8723bs-firmwareHauke Mehrtens2021-12-271-4/+4
| | | | | | | | The firmware for the rtl8723bs chip is now included in the rtl8723bu-firmware package. Fixes: 397dfe4a97e6 ("linux-firmware: Update to version 20121216") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tcpdump: libpcap: Remove http://www.us.tcpdump.org mirrorHauke Mehrtens2021-12-272-4/+2
| | | | | | | | The http://www.us.tcpdump.org mirror will go offline soon, only use the normal download URL. Reported-by: Denis Ovsienko <denis@ovsienko.info> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* linux-firmware: Update to version 20121216Hauke Mehrtens2021-12-272-9/+3
| | | | | | | | | | | | | | | | | | | | | The rtl8723bs firmware was removed and a symlink to the rtl8723bu firmware was created like it is done in upstream linux-firmware. The following OpenWrt packages are changing: * amdgpu-firmware: Multiple updates and new files * ar3k-firmware: Multiple updates and new files * ath10k-firmware-qca6174: Updated ath10k/QCA6174/hw3.0/board-2.bin * bnx2x-firmware: Added bnx2x-e1-7.13.21.0.fw, bnx2x-e1h-7.13.21.0.fw and bnx2x-e2-7.13.21.0.fw * iwlwifi-firmware-iwl8260c: Updated iwlwifi-8000C-36.ucode * iwlwifi-firmware-iwl8265: Updated iwlwifi-8265-36.ucode * iwlwifi-firmware-iwl9000: Updated iwlwifi-9000-pu-b0-jf-b0-46.ucode * iwlwifi-firmware-iwl9260: Updated iwlwifi-9260-th-b0-jf-b0-46.ucode * r8169-firmware: Updated rtl8153c-1.fw * rtl8723bs-firmware: removed * rtl8723bu-firmware: Added rtlwifi/rtl8723bs_nic.bin symlink * rtl8822ce-firmware: Updated rtw8822c_fw.bin Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: mt7622: unifi6lr: properly register Ethernet PHYDaniel Golle2021-12-261-8/+4
| | | | | | | | | | | This change enables proper Ethernet link status and speed reporting on the Ubiquiti UniFi 6 LR access point: mtk_soc_eth 1b100000.ethernet eth0: PHY [mdio-bus:08] driver [Aquantia AQR112C] (irq=POLL) mtk_soc_eth 1b100000.ethernet eth0: configuring for phy/2500base-x link mode mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: enable driver for Aquantia PHYsDaniel Golle2021-12-261-0/+1
| | | | | | | Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T PHY in the Ubiquiti UniFi 6 LR access point. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Clause 45 MDIO accessDaniel Golle2021-12-261-0/+94
| | | | | | | Add support for Clause 45 MDIO PHY register read and write operations to mtk_eth_soc driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: generic: refresh patchDaniel Golle2021-12-261-1/+1
| | | | | | 722-net-phy-aquantia-Add-AQR113-driver-support.patch needs refresh. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: mac80211: refresh patchsetNick Hainke2021-12-241-5/+5
| | | | | | | Refreshed: - 311-mac80211-use-coarse-boottime-for-airtime-fairness-co.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: ath10k: provide a build variant for small RAM devicesNick Hainke2021-12-243-4/+82
| | | | | | | | | | | | | | | | | | | | | | | Based on: 1ac627024de9 ("kernel: ath10k-ct: provide a build variant for small RAM devices") Like described in the ath10k-ct-smallbuffers version, oom-killer gets triggered frequently by devices with small RAM. That change is necessary for many community mesh networks which use ath10k based devices with too little RAM. The -ct driver has been proven unstable if used with 11s meshing and only wave2 chipsets are supporting 11s. Freifunk Berlin is nowadays assembling its firmware-based completely of vanilla OpenWRT with some package additions which are made through the imagebuilder. Therefore we cannot take the approach other freifunk communities have taken to maintain that patch downstream [1]. Other communities consider these devices as broken and that change would pretty much give those devices a second life [2]. [1] - https://git.freifunk-franken.de/mirror/openwrt/commit/450b306e540bc0f2c8a8841bbe4d9612f2b8cdea [2] - https://github.com/freifunk-gluon/gluon/issues/1988#issuecomment-619532909 Signed-off-by: Simon Polack <spolack+git@mailbox.org> Signed-off-by: Nick Hainke <vincent@systemli.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-29 23:33:57 +0000