aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: mt7623: increase flexibility of finding recovery partitionDavid Woodhouse2020-07-261-8/+14
| | | | | | | I'm about to change the layout of the images for UniElec U7623 so make it find the recovery partition based on which the root partition is too. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: add U-Boot build for UniElec U7623David Woodhouse2020-07-264-7/+391
| | | | | | | | | Patches submitted upstream at https://patchwork.ozlabs.org/project/uboot/list/?series=189178 Tested on Banana Pi R2 and U7623-06. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: mt7623: fix Ethernet setup for TRGMII modeDavid Woodhouse2020-07-261-0/+62
| | | | | | This fixes the TX performance issues seen on MT7623 boards. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: fix Ethernet support on UniElec U7623David Woodhouse2020-07-261-10/+4
| | | | | | | The definition of the switch in the device-tree was not correct. Make it look more like the Banana Pi R2, which works. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: mt7623: fix sysupgrade from vendor OpenWrt on UniElec U7623David Woodhouse2020-07-263-6/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board ships with an ancient 14.07-based OpenWrt using block2mtd, and the MBR partition table contains nonsense. It is possible to sysupgrade to an upstream OpenWrt image, but the legacy layout of the OpenWrt images start at 0xA00 in the eMMC, with a raw uImage. The legacy OpenWrt image doesn't "own" the beginning of the device, including the MBR and U-Boot. This means that when a user upgrades to upstream OpenWrt, it doesn't boot because it can't find the right partitions. So hard-code them on the kernel's command line using CONFIG_CMDLINE_PARTITION (for block). Additionally, the vendor firmware doesn't cope with images larger than about 36MiB, because it only overwrites the contents of its "firmware" MTD partition. The current layout of the legacy image wastes a lot of space, allowing over 32MiB for the kernel and another 10MiB for the FAT recovery file system which is only created as 3MiB. So pull those in to allow 4¾ MiB for the kernel, 3MiB for recovery, and then we have over 20MiB for the root file system. This doesn't affect the new images which ship with a full eMMC image including a different MBR layout and a partition for U-Boot, because our modern U-Boot can actually pass the command line to the kernel, and the built-in one doesn't get used anyway. Tested by upgrading from vendor OpenWrt to the current legacy image, from legacy to itself, to the previous legacy layout, and then to finally the full-system image. This commit probably wants backporting to 19.07, which also doesn't install over the vendor OpenWrt and doesn't even have a full-system installation option. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: mt7623: add explicit console= to U7623 kernelDavid Woodhouse2020-07-261-1/+1
| | | | | | | The bootloader for legacy builds can't set it, so we end up unable to log in on the serial port. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* ath79: add support for Compex WPJ563Leon M. George2020-07-263-2/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR 2 Gigabit ethernet ports 3×3 2.4GHz on-board radio miniPCIe slot that supports 5GHz radio PoE 24V passive or 36V-56V passive with optional IEEE 802.3af/at USB 3.0 header Installation: To install, either start tftp in bin/targets/ath79/generic/ and use the u-boot prompt over UART: tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj563-squashfs-sysupgrade.bin erase 0x9f680000 +1 erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize boot The cpximg file can be used with sysupgrade in the stock firmware (add SSH key in luci for root access) or with the built-in cpximg loader. The cpximg loader can be started either by holding the reset button during power up or by entering the u-boot prompt and entering 'cpximg'. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '7A02': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj563-squashfs-cpximg-7a02.bin MAC addresses: <&uboot 0x2e010> *:71 (label) <&uboot 0x2e018> *:72 <&uboot 0x2e020> *:73 <&uboot 0x2e028> *:74 Only the first two are used (for ethernet), the WiFi modules have separate (valid) addresses. The latter two addresses are not used. Signed-off-by: Leon M. George <leon@georgemail.eu>
* lantiq: xrx200: disable unused switch and phyAleksander Jan Bajkowski2020-07-265-7/+6
| | | | | | | | | | | | | | | | | | | | xrx200 has a 6 port built-in switch with 2 integrated PHY. None of the xrx200 router uses external switch. Most boards use integrated or Lantiq (Intel) PEF7071 PHY. Only some FritzBox routers use AT803X PHY and VGV7510KW22 use ICPLUS PHY. Other unused PHY drivers may be removed. This patch enables these symbols only on xway and xway_legacy subtargets: - CONFIG_PSB6970_PHY (Driver for PHY in PSB6970 - 7 port FE Switch) - CONFIG_RTL8366RB_PHY (Driver for PHY in RTL8366 - 6 port GE Switch) - CONFIG_RTL8366_SMI (Driver for RTL8366 - 6 port GE Switch) Reduces image size by 7.3kB. Continuation of 58a6f06978f8 (PR: #2983) Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> [fix sorting in config files, small fix in commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: remove condition in Device/DefaultAdrian Schmutzler2020-07-252-16/+16
| | | | | | | | | | | | | | | | The current condition with part of the variables set dependent on the subtarget in Device/Default isn't really nice to read and also defeats the purpose of having a default node. This removes the special settings for mt7623 and moves them to the individual devices, which is not much of a problem as there are actually just two of them and they partly use different settings anyway. While at it, slightly adjust the order of variables and wrap some long lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: util: don't warn on missing sband iftype dataDavid Bauer2020-07-251-0/+28
| | | | | | | | | | | The kernel currently floods the ringbuffer with warnings when adding a mesh interface for a device not support HE 6GHz modes. Return without warning in this case, as mesh_add_he_6ghz_cap_ie calls ieee80211_ie_build_he_6ghz_cap regardless of the supported interface modes. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: mikrotik: use base mac on lan for RBwAPG-5HacT2HnDBjoern Dobe2020-07-251-0/+4
| | | | | | | | | The Mikrotik RBwAPG-5HacT2HnD has only a single ethernet interface (lan), and the vendor uses the base (label) MAC address for it. Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> [commit title/message improvement] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: rename POWER_ON_STRIP registerSungbo Eo2020-07-2516-25/+25
| | | | | | | | | | AR8327 datasheet[1] calls the register at address 0x0010 "Power-on Strapping Register". As it has nothing to do with "strip", let's rename it to "POWER_ON_STRAP" to make it easier to grasp. [1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: remove non-existant poe_passthrough for RouterBOARD 750Gr3John Thomson2020-07-251-3/+0
| | | | | | | | | | | | | | | | This 750gr3 GPIO17 switch was added based on vendor source, but only the 760iGS (which shares the rbsysfs board identifier) device has the physical wiring. The 750Gr3 actually does not support PoE out. Apart from that, note that the gpio base (480) would have required this GPIO to be referenced as 497 if it was kept. Fixes: 6ba58b7b020c ("ramips: cleanup the RB750Gr3 support") Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Winstars WS-WN583A6Davide Fioravanti2020-07-253-1/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet ports. Even if mine is branded as "Gemeita AC2100", the sticker on the back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6. Probably the real product name is the Wavlink WL-WN583A6 because of the many references to Wavlink in the OEM firmware and bootlog. Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 8MB NOR (GigaDevice GD25Q64B) ETH: 2x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7603E (2x2:2) - 5GHz: 1x MT7615E (4x4:4) - 6 internal antennas BTN: - 1x Reset button - 1x WPS button - 1x ON/OFF switch (working but unmodifiable) - 1x Auto/Schedule switch (working but unmodifiable. Read Note #3) LEDS: - 1x White led - 1x Red led - 1x Amber led - 1x Blue led - 2x Blue leds (lan and wan port status: working but unmodifiable) UART: - 57600-8-N-1 Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M83A6.V5030.191210 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box: mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done 3) Click "Apply" 4) After few seconds, in the textarea should appear this output: 16384+0 records in 16384+0 records out 8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s 384+0 records in 384+0 records out 196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s 15744+0 records in 15744+0 records out 8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s dd: can't open '/dev/mtd5ro': No such device dd: can't open '/dev/mtd6ro': No such device dd: can't open '/dev/mtd7ro': No such device Excluding the "X.XXXXXX seconds" part, you should get the same exact output. If your output doesn't match mine, stop reading and ask for help in the forum. 5) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd0ro http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files weight 0 byte, stop reading and ask for help in the forum. 6) Store these downloaded files in a safe place. 7) Reboot your router to remove any temporary file from your router. Installation ------------ Flash the initramfs image in the OEM firmware interface. When openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) The "System Command" page allows to run every command as root. For example you can use "dd" and "nc" to backup the OEM firmware. PC (SERVER): nc -l 5555 > ./mtdXro ROUTER (CLIENT): dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555 2) The OEM web interface accepts only images containing the string "WN583A6" in the filename. Currently the OEM interface accepts only the initramfs image probably because it checks if the ih_size in the image header is equal to the whole image size (instead of the kernel size) Read more here: https://forum.openwrt.org/t/support-for-strong-1200/22768/19 3) The white led (namely "Smart Night Light") can be controller by the user only if the side switch is set to "Schedule" otherwise it will be activated by the light condition (there is a photodiode on the top side of the router) 4) Router mac addresses: LAN XX:XX:XX:XX:XX:8F WAN XX:XX:XX:XX:XX:90 WIFI 2G XX:XX:XX:XX:XX:91 WIFI 5G XX:XX:XX:XX:XX:92 LABEL XX:XX:XX:XX:XX:91 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [remove chosen node, fix whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* oxnas: use vendor_model scheme for ox810seAdrian Schmutzler2020-07-251-3/+4
| | | | | | | | | | | | Most newer targets have been converted to consistently use vendor_model scheme for device definitions/image names, ox820 is using it as well, so let's just convert ox810se for consistency. While at it, use generic setup for DEVICE_DTS and add SUPPORTED_DEVICES. The latter have been introduced for ox820 already in cf7896117b3e ("oxnas: enable image metadata by setting SUPPORTED_DEVICES") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* procd: jail: fix build on glibc and uclibcDaniel Golle2020-07-251-3/+3
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2020-07-251-3/+3
| | | | | | | | 48777de rcS: cast format string to int64_t a4df90f jail: fix wrong format for 32-bit c482c5d jail: add support for referencing existing namespaces Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* cake-oot: update to latest HEADKevin Darbyshire-Bryant2020-07-241-3/+3
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* build: Remove dependency of user space stack cookies from kernelHauke Mehrtens2020-07-241-2/+0
| | | | | | | | | | | | Currently the user space stack cookies work well also when the kernel stack cookies are not activated. This is handled completely in user space and does not need kernel support. This dependency was probably needed some years ago when the libc did not support stack cookies. Reviewed-by: Ian Cooper <iancooper@hotmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* toolchain: binutils: Use version 2.34 by defaultHauke Mehrtens2020-07-242-5/+2
| | | | | | | | | | | | Switch to binutils version 2.34 for all CPUs by default. The ARC CPUs do not need any special binutils version any more. This increases the image size by 0.2% on MIPS (lantiq) Tested on lantiq, ipq40xx Acked-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: Fix warning in SPI driverHauke Mehrtens2020-07-231-0/+35
| | | | | | | This fixes a warning in the SPI driver at bootup. This warning is seen in kernel 5.4 on lantiq deives. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.8-rc2-1Hauke Mehrtens2020-07-2341-410/+687
| | | | | | | | | | | | | | | | | | | | | | | | The following patches: * 972-ath10k_fix-crash-due-to-wrong-handling-of-peer_bw_rxnss_override-parameter.patch * 973-ath10k_fix-band_center_freq-handling-for-VHT160-in-recent-firmwares.patch are replaced by this commit in the upstream kernel: * 3db24065c2c8 ("ath10k: enable VHT160 and VHT80+80 modes") The following patches were applied upstream: * 001-rt2800-enable-MFP-support-unconditionally.patch * 090-wireless-Use-linux-stddef.h-instead-of-stddef.h.patch The rtw88 driver is now split into multiple kernel modules, just put it all into one OpenWrt kernel package. rtl8812au-ct was patched to compile against the mac80211 from kernel 5.8, but not runtime tested. Add a patch which fixes ath10k on IPQ40XX, this patch was send upstream and fixes a crash when loading ath10k on this SoC. Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq40xx/ map-ac2200] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.7.5-1Hauke Mehrtens2020-07-2312-23/+23
| | | | | | The b43 and b43legacy driver now support DRIVER_11W_SUPPORT. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tools/mkimage: create .itb file with read-access for group,other not just owner.Ted Hess2020-07-231-0/+11
| | | | | | | This patch will fix the source of 403 errors on these files from downloads.openwrt.org. Signed-off-by: Ted Hess <thess@kitschensync.net>
* uboot-mediatek: remove swig requirementRosen Penev2020-07-232-1/+26
| | | | | | | | | Ever since this package was introduced, the SDK for mt7629 failed to build as it started failing on this package. Fixed by porting Hauke's similar patch for uboot-sunxi to uboot-mediatek. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* openvpn: Allow override of interface nameMichal Hrusecky2020-07-232-2/+37
| | | | | | | | | | | If using a configuration file for OpenVPN, allow overriding name of the interface. The reason is that then people could use configuration file provided by VPN provider directly and override the name of the interface to include it in correct firewall zone without need to alter the configuration file. Signed-off-by: Michal Hrusecky <michal@hrusecky.net> (cherry picked from commit c93667358515ec078ef4ac96393623ac084e5c9e)
* openpvn: Split out config parsing code for reuseMichal Hrusecky2020-07-233-13/+23
| | | | | | | | Split out code that parses openvpn configuration file into separate file that can be later included in various scripts and reused. Signed-off-by: Michal Hrusecky <michal@hrusecky.net> (cherry picked from commit 86d8467c8ab792c79809a08c223dd9d40da6da2e)
* ipq40xx: support reset button for WPJ419Phi Nguyen2020-07-231-0/+10
| | | | | | Compex WPJ419 has a reset button on a GPIO pin. Signed-off-by: Phi Nguyen <phind.uet@gmail.com>
* tools/flock: add PKG_{VERSION,RELEASE}Paul Spooren2020-07-231-0/+2
| | | | | | | | | | The stored source code of flock contains the version string of version 2.18, reflect that in the Makefile. Motivation is the tracking of changes in the buildsystem, which requires versioning of packages. Signed-off-by: Paul Spooren <mail@aparcar.org>
* tools/sstrip: add PKG_{VERSION,RELEASE}Paul Spooren2020-07-231-0/+2
| | | | | | | | | | | | Comparing the in tree stored source file of sstrip suggests it's version 2.0[0], reflect that in the Makefile. Motivation is the tracking of changes in the buildsystem, which requires versioning of packages. [0]: https://github.com/BR903/ELFkickers/commit/df4426a0f0ada861064d75c08cbebaac7c16b3ae#diff-d3ba694d91432a068d5d3b36abf8cd0f Signed-off-by: Paul Spooren <mail@aparcar.org>
* tools/firmware-utils: add PKG_RELEASEPaul Spooren2020-07-231-1/+2
| | | | | | | | | | | | There is no versioning information in the firmware-utils code nor the Makefile. Consider it as first release by adding PKG_RELEASE. Motivation is the tracking of changes in the buildsystem, which requires versioning of packages. Also update copyright. Signed-off-by: Paul Spooren <mail@aparcar.org>
* tools/patch-image: add PKG_RELEASEPaul Spooren2020-07-231-1/+2
| | | | | | | | | | | | There is no versioning information in the patch-image code nor the Makefile. Consider it as first release by adding PKG_RELEASE. Motivation is the tracking of changes in the buildsystem, which requires versioning of packages. Also update copyright. Signed-off-by: Paul Spooren <mail@aparcar.org>
* tools: drop PKG_VERSION for purely local packagesAdrian Schmutzler2020-07-232-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This applies to tools directory what has been done for package/ in commit 9c170cb92f4f ("package: drop PKG_VERSION for purely local packages"): In the package guidelines, PKG_VERSION is supposed to be used as "The upstream version number that we're downloading", while PKG_RELEASE is referred to as "The version of this package Makefile". Thus, the variables in a strict interpretation provide a clear distinction between "their" (upstream) version in PKG_VERSION and "our" (local OpenWrt trunk) version in PKG_RELEASE. For local (OpenWrt-only) packages, this implies that those will only need PKG_RELEASE defined, while PKG_VERSION does not apply following a strict interpretation. While the majority of "our" packages actually follow that scheme, there are also some that mix both variables or have one of them defined but keep them at "1". This is misleading and confusing, which can be observed by the fact that there typically either one of the variables is never bumped or the choice of the variable to increase depends on the person doing the change. Consequently, this patch aims at clarifying the situation by consistently using only PKG_RELEASE for "our" packages. For tools/, only three packages were affected. This fixes two of them, and leaves the remaining wrt350nv2-builder untouched, as the code there seems to have some versioning of its own that is treated as upstream version in PKG_VERSION. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "ramips: fix flash layout for TP-Link TL-WR841N v14"Adrian Schmutzler2020-07-222-8/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 1623defbdbb852a4018329d07673b4b8f66225a8. As already stated in the reverted patch, the OEM firmware will properly recreate the config partition if it is overwritten by OpenWrt. The main reason for adding the partition was the image size restriction imposed by the 0x3d0000 limitation of the TFTP flashing process. Addressing this by shrinking the firmware partition is not a good solution to that problem, though: 1. For a working image, the size of the content has to be smaller than the available space, so empty erase blocks will remain. 2. Conceptually, the restriction is on the image, so it makes sense to implement it in the same way, and not via the partitioning. Users could e.g. do initial flash with TFTP restriction with an older image, and then sysupgrade into a newer one, so TFTP restriction does not apply. 3. The (content) size of the recovery image is enforced to 0x3d0000 by the tplink-v2-image command in combination with TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* arc770: use generic 02_sysinfoAdrian Schmutzler2020-07-223-47/+1
| | | | | | | | | | | | | | | | | Currently arc770 sets a board name from compatible for no apparent reason. Just use the compatible directly instead. This theoretically removes a board name "generic" when no compatible was present, however, there is no case where this "generic" board name was actually used. This also fixes an issue where snps,axs101 would not have been properly detected anyway, as its case was not set up syntactically correct. Fixes: 576621f1e353 ("linux: add support of Synopsys ARC770-based boards") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* archs38: use generic 02_sysinfoAdrian Schmutzler2020-07-223-51/+2
| | | | | | | | | | | | | | | | | Currently archs38 sets a board name from compatible for no apparent reason. Just use the compatible directly instead. This theoretically removes a board name "generic" when no compatible was present, however, there is no case where this "generic" board name was actually used. This also fixes an issue where snps,axs103 would not have been properly detected anyway, as its case was not set up syntactically correct. Fixes: 73015c4cb378 ("linux: add support of Synopsys ARCHS38-based boards") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: switch MT7620 subtarget to 5.4David Bauer2020-07-221-0/+2
| | | | | | | | | MT7620 seems to work fine with kernel 5.4. Set the default kernel version to 5.4 to bring this to a broader audience. Tested on Archer C2 v1 / Archer C20i Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: increase SPI frequency for MT7620 ArcherDavid Bauer2020-07-223-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Increase the SPI frequency for the MT7620 based TP-Link Archer series to 30MHz. TP-Link uses different SPI flash chips for the same board revision, so be conservative to not break boards with a different chip. 30MHz should be well supported by all chips. Tested on Archer C2 v1 (GD25Q64B) and Archer C20i (W25Q64FV). Archer C20i (before) ==================== root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k 122+0 records in 122+0 records out real 0m 15.30s user 0m 0.00s sys 0m 15.29s Archer C20i (after) =================== root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k 122+0 records in 122+0 records out real 0m 5.99s user 0m 0.00s sys 0m 5.98s Signed-off-by: David Bauer <mail@david-bauer.net> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: re-enable image generation for GL-AR750SDavid Bauer2020-07-224-33/+23
| | | | | | | | | | | | | | | | The bootloader only writes the first 2MB of the image to the NOR flash when installing the NAND factory image. The bootloader is capable of booting larger kernels as it boots from the memory mapped SPI flash. Disable the NAND factory image. The NAND can be bootstrapped by writing the NAND initramfs image using the NOR upgrade method in the bootloader web-recovery and sysupgrading from there. The NOR variant is not affected. Also refactor the partition definitions in the DTS to make them less annoying to read. Signed-off-by: David Bauer <mail@david-bauer.net>
* kmod-sched-cake-oot: fix PKG_MIRROR_HASHKevin Darbyshire-Bryant2020-07-221-1/+1
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* umdns: fix compiling using gcc 10Kevin Darbyshire-Bryant2020-07-221-3/+3
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* glibc: fix memcpy and memmove for negative length [BZ #25620]Hans Dedecker2020-07-211-2/+2
| | | | | | | | 6f3459f985 Add NEWS entry for CVE-2020-6096 (bug 25620) 64246fccaf arm: CVE-2020-6096: Fix multiarch memcpy for negative length [BZ #25620] 9bbd2b6172 arm: CVE-2020-6096: fix memcpy and memmove for negative length [BZ #25620] Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: correctly define WiFi switch for TL-WR841ND v8Adrian Schmutzler2020-07-214-34/+51
| | | | | | | | | | | | | | | | | | | | | | | | The TL-WR841ND v8 feature a WiFi switch instead of a button. This adds the corresponding input-type to prevent booting into failsafe regularly. This has been defined correctly in ar71xx, but was overlooked when migrating to ath79. In contrast, the TL-WR842ND v2, which has the key set up as switch in ar71xx, actually has a button. The TL-MR3420 v2 has a button as well and is set up correctly for both targets. (Information based on TP-Link user guide) Note: While looking into this, I found that support PR for TL-MR3420 v2 switched reset button to ACTIVE_HIGH. However, the other two device still use ACTIVE_LOW. This seems strange, but I cannot verify it lacking the affected devices. Fixes: FS#2733 Fixes: 9601d94138de ("add support for TP-Link TL-WR841N/ND v8") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve LED support for D-Link DIR-615 D seriesAdrian Schmutzler2020-07-212-5/+8
| | | | | | | | | | | | | This patch adds a trigger for the WAN LED and enhances support for the WiFi LED by enabling activity indication. This is based on bug report feedback (see reference below). While at it, update the LED node names in DTS file. Fixes: FS#732 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* omap: derive DEVICE_DTS from device nameAdrian Schmutzler2020-07-211-3/+1
| | | | | | | | In most cases the DEVICE_DTS name can be derived easily from the node name, so let's do this to enforce harmonized names where possible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* apm821xx: derive DEVICE_DTS from device nameAdrian Schmutzler2020-07-213-6/+1
| | | | | | | | | | | The DEVICE_DTS variable always matches the device definition name, just with "_" replaced by "-". Thus, create a DEVICE_DTS definition in Device/Default and drop all the individual statements. If necessary in the future, local DEVICE_DTS will still overwrite that default. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm47xx: fix switch setup for Linksys WRT610N v2Adrian Schmutzler2020-07-211-0/+1
| | | | | | | | | | | | WRT610N V2 is not detected by the initial network configuration script. The switch remains unconfigured and wlan/lan vlans are not created. This adds the correct setup for the device. Fixes: FS#1869 Suggested-by: Alessandro Radicati Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* layerscape: fix indentAdrian Schmutzler2020-07-211-2/+2
| | | | | | Fix indent to be consistent with the rest of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix network setup for Ubiquiti ER-X/ER-X-SFPNelson Cai2020-07-201-2/+2
| | | | | | | | | | | | The function name ucidef_set_interface_lan_wan does not exist, use the proper name by adding an "s" and thereby fix network setup on these devices. Fixes: 22468cc40c8b (ramips: erx and erx-sfp: fix missing WAN interface) Signed-off-by: Nelson Cai <niphor@gmail.com> [commit message/title facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* hostapd: enter DFS state if no available channel is foundDavid Bauer2020-07-201-0/+37
| | | | | | | | | | | Previously hostapd would not stop transmitting when a DFS event was detected and no available channel to switch to was available. Disable and re-enable the interface to enter DFS state. This way, TX does not happen until the kernel notifies hostapd about the NOP expiring. Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 22:52:36 +0000