aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: Askey RT4230W REV6: use usual writing for pcie partChukun Pan2021-08-251-3/+5
| | | | | | | | The problem has been fixed in f47cb405cafd ("ipq806x: fix pci broken on bootm command"), now the pcie part can be written in the usual way. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
* ramips: add support for DomyWifi DM202/DM203/DW22DShiji Yang2021-08-257-0/+255
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SOC: MT7620A + MT7610E * ROM: 16 MiB spi flash (W25Q128FVSG) * RAM: 128 MiB DDR2 (W971GG6KB-25) * WAN: 10/100M *1 * LAN: 10/100M *4 * USB: Type-A USB2.0 *1 * SD: MicroSD *1 * Button: Reset *1 * Antennas: 2.4 GHz *2 + 5 GHz *1 * TTL Baudrate: 57600 * U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3 Installation: * Web UI Update 1. Open http://192.168.10.1/upgrade.html in the browser. 2. Rename firmware to a short name like firmware.bin and then upload it. 3. Fill in the password column with the following content: password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware * TFTP + U-Boot 1. Connect device with a TTL cable. 2. Press "2" when booting to select "Load system code then write to Flash via TFTP". 3. Upload firmware by tftpd64, it will boot when write instruction is executed. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Motorola MWR03Shiji Yang2021-08-253-0/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SOC: MT7628AN + MT7612E * ROM: 8 MiB Flash * RAM: 64 MiB DDR2 * WAN: 10/100M *1 * LAN: 10/100M *3 * Button: Reset *1 * LEDs: orange *1, white *1 * Antennas: 2.4 GHz *2 + 5 GHz *2 * TTL Baudrate: 57600 * TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100 MAC addresses as verified by OEM firmware: use address source 2g *:d8 factory 0x0004 (label) 5g *:d9 factory 0x8004 LAN *:d7 factory $label -1 WAN *:da factory $label +2 Installation (TFTP + U-Boot): * Connect device with a TTL cable and open a serial session by PuTTY. * Press "2" when booting to select "Load system code then write to Flash via TFTP". * Configure the IP of local host server. * Upload firmware by tftpd64, it will boot when write instruction is executed. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [fix DTS line endings, fix label MAC address, adjust status LED names, convert mtd-mac-address-increment to mac-address-increment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: Askey RT4230W REV6: fix caldata scriptChukun Pan2021-08-241-2/+6
| | | | | | | | | | The partition name in the device dts is '0:ART'. Be independent to prevent this part from becoming incorrect once the kernel v5.4 gone. Fixes: da8428d277cd ("ipq806x: add support for Askey RT4230W REV6") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: add new flash layout support to Phicomm K2Shiji Yang2021-08-244-15/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Descriptions： Phicomm K2 (PSG1218) got a new "permanent_config" partition after update firmware to v22.5. This partition located in front of the firmware partition, same as The Phicomm K2P and K2G. Due to this change the new bootloader can't load previous firmware any more. This commit is aimed at add support for Phicomm K2 which official firmware version is 22.5.x or newer. For which runs old firmware version, just update OpenWrt that has a prefix of "k2-v22.4". For uniform naming, this commit also changed the model name PSG1218 to a more recognizable name K2, refer to Phicomm K2G, K2P K2T. OpenWrt selection table: official firmware version OpenWrt v22.4.x.x or older phicomm_k2-v22.4 v22.5.x.x or newer phicomm_k2-v22.5 Installation: Same as Phicomm K2G, K2P, PSG1208. a. TFTP + U-Boot b. Open telnet by some web page vulnerability (Search Baidu by key words "K2 telnet"), and then we can upload firmware image to /tmp and write it to firmware partition with mtd instruction. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [rebase, add/harmonize version in model variables, fix version typo in commit message, wrap commit message properly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: move Phicomm MAC address setup to DTSIAdrian Schmutzler2021-08-244-41/+15
| | | | | | The setup is the same for all devices, so move it up one level. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* procd: update to git HEADDaniel Golle2021-08-241-3/+3
| | | | | | | | | | | | | | | | 8a8306d uxc.c: fix coverity resource leak warning 7f2398e jail: devices: create parent folder when creating devices 0603c8d jail: return to hook callback instead of just calling it 3edb7eb jail: check return value when opening console af048a3 jail: use portable sizeof(void *) 6010bd3 utils: make sure read() string is 0 terminated f6daca3 uxc: free string returned by blobmsg_format_json_indent() 51f1cd2 trace: free string returned by blobmsg_format_json_indent() d716cb5 trace: handle open() return value and make sure string is terminated b824a89 jail: preload: avoid NULL-dereference in case things go wrong 167dc24 jail: protect against strcat buffer overflows Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* netifd: update to the latest versionFelix Fietkau2021-08-241-3/+3
| | | | | | | | | | 94170ae24bc9 device: extend device settings flags to 64 bit 1eb0fafaa986 device: add support for configuring device link speed/duplex ed84473b7af9 bridge: memset bst->config by default to avoid stale config values 6519cf31e4b0 bridge: add support for an external STP daemon 454e9c33c906 bridge: tune default stp parameters Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: update to the latest versionFelix Fietkau2021-08-241-3/+3
| | | | | | d716ac4bc423 list.h: add a few missing iterator macros Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add missing change for encap offload on devices with sw rate controlFelix Fietkau2021-08-243-21/+65
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: refresh patchFelix Fietkau2021-08-241-12/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: enable ht40 in wpa_supplicant when using wider HE modesFelix Fietkau2021-08-241-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix HT40 mode for 6G bandFelix Fietkau2021-08-241-3/+4
| | | | | | The channel offset used for VHT segment calculation was missing for HT Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uhttpd: add config option for json_scriptStijn Tintel2021-08-242-2/+3
| | | | | | | | | | Add a config option for json_script instead of unconditionally including all json files in /etc/uhttpd in every uhttpd instance. This makes it possible to configure a single instance with an unconditional redirect, which currently renders all other uhttpd instances unusable. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Felix Fietkau <nbd@nbd.name>
* odhcpd: update to latest git HEADHans Dedecker2021-08-231-3/+3
| | | | | | | 01b4e60 dhcpv4: fix uninitialized hostname in some ubus events 1666769 dhcpv6-ia: allow up to 64 bit wide hostid Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* base-files: fix option to make /var persistentStijn Tintel2021-08-231-1/+1
| | | | | | | | | | | | The option was initially named TARGET_ROOTFS_LN_VAR_TMP, and the check was correct. When renaming the option to something more suitable, the check was changed to check for n, but when an option is not set, it's not n but empty. This results in the check always evaluating to false. Fix the check by checking for y with ifneq. Fixes: 57807f50ded6 ("base-files: add option to make /var persistent") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ath79: add support for Atheros DB120 reference boardZoltan HERPAI2021-08-224-14/+292
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Atheros DB120 reference board. Specifications: SoC: QCA9344 DRAM: 128Mb DDR2 Flash: 8Mb SPI-NOR, 128Mb NAND flash Switch: 5x 10/100Mbps via AR8229 switch (integrated into SoC), 5x 10/100/1000Mbps via QCA8237 via RGMII WLAN: AR9300 (SoC, 2.4G+5G) + AR9340 (PCIe, 5G-only) USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x reset LEDs: a lot Slots: 2x mPCIe + 1x mini-PCI, but using them requires additional undocumented changes. Misc: The board allows to boot off NAND, and there is I2S audio support as well - also requiring additional undocumented changes. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-atheros_db120-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> [explicit factory recipe in generic.mk, sorting in 10-ath9k-eeprom, convert to nvmem, use fwconcat* names in DTS, remove unneeded DT labels, remove redundant uart node] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBeam M2 (XW)Russell Senior2021-08-224-0/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Ubiquiti PowerBeam M2 (XW), e.g. PBE-M2-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-ubnt_powerbeam-m2-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM2HP Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: rename Ubiquiti PowerBeam M (XW) to PowerBeam M5 (XW)Russell Senior2021-08-224-7/+7
| | | | | | | | | | | | | | The commit [1] added support for Ubiquiti PowerBeam M (XW), tested on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different ethernet configuration, so make the support specific to the m5 version in anticipation of adding specific support for the m2 in a separate commit. [1] 12eb5b2384a6 ("ath79: add support for Ubiquiti PowerBeam M (XW)") Signed-off-by: Russell Senior <russell@personaltelco.net> [fix model name in DTS, format commit reference in commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: add option to make /var persistentStijn Tintel2021-08-222-0/+13
| | | | | | | | | | | | | | | | In OpenWrt, /var is symlinked to /tmp by default. This is done to reduce the amount of writes to the flash chip, which often have not the greatest durability. As a result, things like DHCP or UPnP lease files, are not persistent across reboots. Since OpenWrt can run on devices with more durable storage, it makes sense to have an option for a persistent /var. Add an option to make /var persistent. When enabled, /var will no longer be symlinked to /tmp, but /var/run will be symlink to /tmp/run, as it should contains only files that should not be kept during reboot. The option is off by default, to maintain the current behaviour. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* lldpd: bump to 1.0.12Stijn Tintel2021-08-221-3/+3
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mediatek: mt7623: enable clock drivers for Mali-450 and audioDaniel Golle2021-08-221-2/+2
| | | | | | | Built clock drivers for G3DSYS and AUDSYS into the kernel to allow multimedia features (GPU and audio) to work if they exist. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq806x: fix min<>target opp-microvolt DTS mixupShane Synan2021-08-215-96/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rearrange all voltage triplets for "opp_table0" to match the specifications. "opp-microvolt" and "opp-microvolt-<name>" triplets are in order of <target min max>, and NOT <min target max>. Previously, the CPU would *always* spend its time at the "minimum" voltage, ignoring the actual intended target. This is a regression from previous behavior. On an NBG6817 with a Qualcomm CPU of PVS bin #2... (see &opp_table0 -> opp-1725000000 -> opp-microvolt-speed0-pvs2-v0) * Before: /usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_* ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <== 1260000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <== 1200000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <== 1140000 * After: /usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_* ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <== 1260000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <== 1140000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <== 1200000 To check voltages and frequencies at run time, use... /bin/cat /sys/kernel/debug/regulator/regulator_summary && /bin/cat /sys/kernel/debug/clk/clk_summary | grep "hfpll" See https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/Documentation/devicetree/bindings/opp/opp.txt?h=v5.4.142#n91 Fixes: 1e25423be8ac ("ipq806x: refresh dtsi patches") Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com> Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com> [commit message style cleanup, another kernel refresh] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for Onion Omega 2(+)Adrian Schmutzler2021-08-211-4/+6
| | | | | | | | | | Thanks to a hint from Michael Siegenthaler in 4b4fa2f9fed7 ("ramips: fix ethernet MAC address on Omega2"), the label MAC address of the Onion Omega 2(+) can be set based on its documentation [1]. [1] https://docs.onion.io/omega2-docs/mac-address.html Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* firmware-utils: fix build on not LinuxKevin Darbyshire-Bryant2021-08-212-2/+2
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ltq-vdsl: add missing backslashJan Hoffmann2021-08-211-2/+2
| | | | | | This error was introduced with the recent cleanup. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* bcm27xx: switch to kernel 5.10Álvaro Fernández Rojas2021-08-211-1/+1
| | | | | | | After testing it on RPi B+ and RPi 4B it seems stable enough to enable it on OpenWrt master. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: add kernel 5.10 supportÁlvaro Fernández Rojas2021-08-21745-2/+227568
| | | | | | | | | | | Rebased RPi foundation patches on linux 5.10.59, removed applied and reverted patches, wireless patches and defconfig patches. bcm2708: boot tested on RPi B+ v1.2 bcm2709: boot tested on RPi 4B v1.1 4G bcm2711: boot tested on RPi 4B v1.1 4G Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* generic: fix debloat dma-buf 5.10 patchÁlvaro Fernández Rojas2021-08-211-2/+12
| | | | | | | | | | The current patch produces the following error when CONFIG_DMABUF_HEAPS is enabled: drivers/built-in.a: member drivers/dma-buf/heaps in archive is not an object Fixes: b10d6044599d ("kernel: add linux 5.10 support") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* generic: add missing 5.10 config symbolsÁlvaro Fernández Rojas2021-08-211-0/+15
| | | | | | These symbols are needed for bcm27xx 5.10 kernel support. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx-gpu-fw: update to latest versionÁlvaro Fernández Rojas2021-08-211-15/+15
| | | | | | Multiple firmware fixes needed for kernel updates. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx-userland: update to latest versionÁlvaro Fernández Rojas2021-08-211-2/+2
| | | | | | Properly recognise all BCM2711 variants Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mediatek: mt7623: backport musb, improve HDMI consoleDaniel Golle2021-08-216-5/+369
| | | | | | | | | Backport support for dual-role USB 2.0 as that's what is actually built-into MT7623. Improve HDMI console by enabling VT and setting up tty1..tty6. Re-add accidentally removed CONFIG_ARM_ARCH_TIMER. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* prereq-build: require python3-distutilsAndre Heider2021-08-211-0/+4
| | | | | | | | | | | | | | | | | | | | | | | Debian and Ubuntu ship a python3-minimal package which does not include the distutils module. This is not supported by upstream and can be considered a broken python distribution. In practice, many scripts depend on said module, and this is a reoccuring pain point for building various OpenWrt packages. Require and check for said module, enough time has been wasted on this. A list of just the most recent issues: https://github.com/openwrt/packages/pull/16304 https://github.com/openwrt/packages/pull/16027 https://github.com/openwrt/packages/pull/15443 https://github.com/openwrt/packages/pull/14394 https://github.com/openwrt/packages/pull/12909 https://github.com/openwrt/packages/issues/12443 https://github.com/openwrt/packages/pull/11035 https://github.com/openwrt/packages/issues/10993 Signed-off-by: Andre Heider <a.heider@gmail.com>
* ramips: fix ethernet MAC address on Omega2Michael Siegenthaler2021-08-211-3/+3
| | | | | | | | | | | | | | | | According to https://docs.onion.io/omega2-docs/mac-address.html, 0x28 is the correct location to read the address on Onion Omega 2(+) devices. This fixes a regression introduced by commit 77e850fe76e3 ("ramips: tidy up MAC address setup for Linkit Smart and Omega2"), which was a cleanup that intended to preserve existing behavior. In my testing with v19.07.7, however, the MAC address determined from the device tree takes precedence over the one set by 02_network, so the aforementioned commit actually changed the behavior. Signed-off-by: Michael Siegenthaler <msiegen@google.com> [Adapt patch to nvmem usage] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ltq-vdsl/ltq-vdsl-app: clean up configure argsJan Hoffmann2021-08-212-16/+10
| | | | | | | | | | | | | | | | | | | | | The userspace application now uses the model=full option to match the configuration of the kernel module. The source no longer contains SOAP support, which was the primary reason to build only typical instead of full before. This makes several CLI commands, which were already supported in the kernel module, available in the userspace application. For example, this includes bbsg which allows to get information about VDSL2 bands. Some previously applied build options were redundant. Disabling ADSL MIB support is unnecessary, as it only applies to Danube. ADSL LED support is no longer included in the source. ReTx counters are already included with model type full. This increases the size of the userspace application by approximately 15 kB (uncompressed). The kernel module does not change at all. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* firmware-utils: add support for ZyXEL ZLD firmwareVincent Wiemann2021-08-212-1/+832
| | | | | | | | | | | | | | | | This commit adds a tool for extracting and creating firmware archives for: - ZyXEL NWA5121-N - ZyXEL NWA5121-NI - ZyXEL NWA5123-NI - ZyXEL NWA5123-AC - ZyXEL NWA5301 - ZyXEL NWA3560N v2 - ZyXEL WAC6100 - ZyXEL WAC6500 And maybe others... Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
* dropbear: allow to use with xinetdFritz D. Ansel2021-08-211-2/+0
| | | | | | | | | | | | | with xinetd allowed+blocked (ipv6) hosts could be set what is not possible with stock dropbear package The file size increased 12 Bytes, so this "opimisation" did not really helped. Within a compressed storage format it is 0.. ipk: 111.171 -> 111.361 = 190 bytes bin: 215.128 -> 215.140 = 12 bytes Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
* kernel: bump 5.4 to 5.4.142John Audia2021-08-2113-113/+57
| | | | | | | | | | | | | | | Removed upstreamed: hack-5.4/991-platform-x86-pcengines-apuv2-revert-simswitch.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.141John Audia2021-08-215-6/+6
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.60Rui Salvaterra2021-08-215-8/+8
| | | | | | No deleted or manually refreshed patches. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* gdb: update to 10.2Rosen Penev2021-08-217-106/+100
| | | | | | | | | | | Replace some OpenWrt patches with openembedded ones for easier maintainability. Remove several outdated ones as well. Replace PKG_RELEASE with AUTORELEASE to avoid manual bumps. Remove !arc dependency as it is supported upstream now. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: mt7623: enable more hardware featuresDaniel Golle2021-08-214-15/+118
| | | | | | | In order to make HDMI console available on the BananaPi BPi-R2 select various Kconfig symbols which are useful for systems with graphics. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: pass console=tty1 for BPi-R2Daniel Golle2021-08-211-1/+1
| | | | | | | BananaPi BPi-R2 comes with HDMI and MIPI-DSI. Use dislpay facility in Linux by add "console=tty1" boot argument. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: Do not deactivate staging driversHauke Mehrtens2021-08-216-6/+0
| | | | | | | | | Do not deactivate the kernel configuration symbol CONFIG_STAGING in the target configurations any more. This prevented the build of the exfat.ko for example. Fixes: FS#3979 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* layerscape: Do not activate ext2 and ext3 driver optionsHauke Mehrtens2021-08-211-6/+0
| | | | | | | | The ext3 driver was already removed, the kernel config options are only there for backwards compatibility. The eth4 driver takes care of ext3 file systems. The ext4 driver also handled ext2 file systems. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* archs38: Do not activate ext3 driver optionsHauke Mehrtens2021-08-211-3/+0
| | | | | | | | The ext3 driver was already removed, the kernel config options are only there for backwards compatibility. The eth4 driver takes care of ext3 file systems. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* at91bootstrap: Fix compile with binutils 2.36Hauke Mehrtens2021-08-211-0/+38
| | | | | | | This fixes a build problem seen after binutils 2.36 is used by default. Fixes: 3f41153b1c28 ("toolchain/binutils: switch to version 2.36.1 by default") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-at91: fix dtc compilation on host gcc 10Hauke Mehrtens2021-08-212-9/+49
| | | | | | Backport a patch from upstream U-Boot to fix the compile with host GCC 10. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* wolfssl: fix build with GCC 10 on 32 x86 targetsStijn Tintel2021-08-201-0/+123
| | | | | | Backport upstream patch to fix build with GCC 10 on 32 x86 targets. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-17 00:48:38 +0000