aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Qualcomm AP143 reference boardsZoltan HERPAI2021-06-057-1/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9533 DRAM: 32Mb DDR1 Flash: 8/16Mb SPI-NOR LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC) on GMII WAN: 1x 10/100Mbps via MII WLAN: QCA9530 USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x WPS, 1x reset LEDs: 8x LEDs A version with 4Mb flash is also available, but due to lack of enough space it's not supported. As the original flash layout does not provide enough space for the kernel (1472k), the firmware uses OKLI and concat flash to overcome the limitation without changing the boot address of the bootloaders. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize Reboot the board. 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. For the 16M version of the board, please use openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> [use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE, set up IMAGE/factory.bin without metadata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for OpenMesh A40Sven Eckelmann2021-06-056-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh A60Sven Eckelmann2021-06-057-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8031 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* mac80211: split ath patch in dedicated subdirAnsuel Smith2021-06-0449-0/+8
| | | | | | | | | | The ath patch number is already large and adding other patch for ath11k will add more confusion with the patch numbering. Since the support of ath11k based device is imminent, prepare the mac80211 ath patch dir and split it in the dedicated ath5k, ath9k, ath10k and ath11k (empty for now). Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* hostapd: fix bringing up vlan interfaces with the no-bridge optionFelix Fietkau2021-06-041-7/+15
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: update to the latest versionFelix Fietkau2021-06-041-3/+3
| | | | | | | | | 61a71e5e49c3 bridge: dynamically create vlans for hotplug members cb6ee9608e10 bridge: fix dynamic delete of hotplug vlans 7f199050f395 wireless: pass the real network ifname to the setup script 50381d0a2998 bridge: allow adding/removing VLANs to configured member ports via hotplug Signed-off-by: Felix Fietkau <nbd@nbd.name>
* odhcpd: update to git HEADHans Dedecker2021-06-031-3/+3
| | | | | | | | a12fcb3 config: log config parse failures to syslog ebd4297 cmake: enforce additonal compiler checks 405da32 odhcpd: fix extra compiler warning Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* hostapd: fix radius problem due to invalid attributesJohn Crispin2021-06-031-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | The offending commit caused the configuration file to contain: radius_auth_req_attr= radius_acct_req_attr= which cause hostapd to add an ATTR of type 0 into the messages. hostapd: RADIUS message: code=4 (Accounting-Request) identifier=0 length=93 hostapd: Attribute 40 (Acct-Status-Type) length=6 hostapd: Value: 7 hostapd: Attribute 30 (Called-Station-Id) length=28 hostapd: Value: 'C4-41-1E-F5-2D-55:OpenWifi' hostapd: Attribute 61 (NAS-Port-Type) length=6 hostapd: Value: 19 hostapd: Attribute 0 (?Unknown?) length=3 <---------------- hostapd: Attribute 55 (Event-Timestamp) length=6 hostapd: Value: 1622726457 hostapd: Attribute 41 (Acct-Delay-Time) length=6 hostapd: Value: 0 hostapd: Attribute 44 (Acct-Session-Id) length=18 hostapd: Value: '9B5961E7235AAEC6' Fixes: 3bd6c8c728e (hostapd: add additional radius options) Signed-off-by: John Crispin <john@phrozen.org>
* ubus: update to version 2021-06-03Petr Štetiar2021-06-031-3/+3
| | | | | | | | | | | This update contains following changes: * ubusd: protect against too-short messages * ubusd: add per-client tx queue limit * ubusd: convert tx_queue to linked list Fixes: FS#1525 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mac80211: fix typoFelix Fietkau2021-06-031-1/+1
| | | | | | Remove stray parenthesis Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: ar8216: remove soft_resetDavid Bauer2021-06-031-8/+0
| | | | | | | | | | ar8xxx_soft_reset is effectively a NOP function. In the PHY state machine, the availability and result of a soft_reset function makes no difference for the code flow. Thus, we can safely remove this method. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: ar8216: add get_features methodDavid Bauer2021-06-031-23/+20
| | | | | | | | | | | | | | Modifying PHY capabilities in the probe function broke with upstream commit 92ed2eb7f4b7 ("net: phy: probe the PHY before determining the supported features"). AR8316 switches only support 10/100 Mbit/s link modes because of this change. Provide a get_features method for the PHY driver, so Gigabit link mode will be advertised to link partners again. Signed-off-by: David Bauer <mail@david-bauer.net>
* build/json: fix DEVICE_PACKAGESPaul Spooren2021-06-021-1/+1
| | | | | | | | | | The variable was missing in the definition of DEFAULT_DEVICE_VARS which caused it to contain wrong values, messing up the resulting JSON files. This patch adds the variable DEVICE_PACKAGES to DEFAULT_DEVICE_VARS. Suggested-by: Baptiste Jonglez <git@bitsofnetworks.org> Signed-off-by: Paul Spooren <mail@aparcar.org>
* mt76: update to the latest versionFelix Fietkau2021-06-021-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | bddc1db76d0f mt76: mt7915: drop the use of repeater entries for station interfaces 3c90f35dddac mt76: mt7915: add thermal sensor device support afab0e8202ff mt76: mt7915: add thermal cooling device support 41cf02184699 mt76: mt7615: add thermal sensor device support 2ac6b8762565 mt76: connac: update BA win size in Rx direction ddb301127291 mt76: mt7921: fix reset under the deep sleep is enabled e4cbefd1d69a mt76: mt7921: avoid unnecessary consecutive WiFi resets 393eea2034d7 mt76: mt7921: fix invalid register access in wake_work a15d46407ffa mt76: mt7921: fix OMAC idx usage e4d267d8e900 mt76: mt7921: enable runtime pm by default 50fd8ce2412a mt76: connac: add bss color support for sta mode e29058c3c860 mt76: mt7921: return proper error value in mt7921_mac_init c89c8c347b1e mt76: mt7921: do not schedule hw reset if the device is not running 9f7bb428e587 mt76: mt7921: reset wfsys during hw probe 22ea365913b5 mt76: mt7915: add .offset_tsf callback ad91f8e8e494 mt76: mt7615: add .offset_tsf callback 6f871f35e3c1 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower 597b68b7daa3 mt76: mt7615: remove useless if condition in mt7615_add_interface() 3945264468eb mt76: testmode: fix memory leak in mt76_testmode_alloc_skb bdcc57a11606 mt76: testmode: remove unnecessary function calls in mt76_testmode_free_skb a9763452601d mt76: testmode: remove undefined behaviour in mt76_testmode_alloc_skb 4aef2a2be464 mt76: mt7615: fix potential overflow on large shift d9dd7635b055 mt76: mt7915: use mt7915_mcu_get_mib_info() to get survey data d740e921758a mt76: mt7921: introduce mac tx done handling 259ddfc7cb73 mt76: mt7921: update statistic in active mode only 757b93f4b179 mt76: mt7921: remove leftover 80+80 HE capability 1fcff599b2e1 mt76: allow hw driver code to overwrite wiphy interface_modes c55c22e39b7d mt7915: update firmware to 2020110522 10548aef1f45 mt76: mt7915: improve error recovery reliability ed6b0c79820c mt76: mt7921: set MT76_RESET during mac reset 321443258bea mt76: move mt76_rates in mt76 module d1652e8af9e1 Revert "mt76: connac: do not schedule wake_work if the runtime-pm is disabled" 4f4cab39ed9f mt76: mt7915: read all eeprom fields from fw in efuse mode 71450535f164 mt76: mt7921: enable hw offloading for wep keys 833d577e430c mt76: mt7921: remove mt7921_get_wtbl_info routine 67b7a22d2b99 mt76: mt7921: enable random mac address during sched_scan cf1ff7bf4f1b mt76: mt7915: setup drr group for peers ef2f7aa8745f mt76: mt7615: update radar parameters b9f09f530223 mt76: mt7915: fix MT_EE_CAL_GROUP_SIZE Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add eap_server supportJohn Crispin2021-06-021-4/+21
| | | | | | | This makes it possible to avoid using a RADIUS server for WPA enterprise authentication Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add default values for r0kh/r1khFelix Fietkau2021-06-021-0/+7
| | | | | | | This allows WPA enterprise roaming in the same mobility domain without any manual key configuration (aside from radius credentials) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add support for specifying the maxassoc parameter as a device optionFelix Fietkau2021-06-022-1/+85
| | | | | | | It allows enforcing a limit on associated stations to be enforced for the full device, e.g. in order to deal with hardware/driver limitations Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add support for configuring proxy ARPFelix Fietkau2021-06-021-2/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add configurable rssi thresholds for rejecting assoc/probe requestsFelix Fietkau2021-06-021-1/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add support for configuring the beacon rateFelix Fietkau2021-06-021-1/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: do not enable VHT in the default config on 2.4 GHzFelix Fietkau2021-06-021-1/+1
| | | | | | | Some drivers advertise it, but it's not supported at the moment Reported-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix detecting VHT capabilities when generating the default configFelix Fietkau2021-06-021-1/+1
| | | | | | | The colon does not directly follow the "VHT Capabilities" string Reported-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport fix for hang on napi_disable with threaded NAPIFelix Fietkau2021-06-012-4/+57
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* glibc: update to latest 2.33 HEAD (BZ #27892)Hans Dedecker2021-05-301-2/+2
| | | | | | 0ef0e6de7f powerpc: Fix handling of scv return error codes [BZ #27892] Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* layerscape: refresh kernel configAdrian Schmutzler2021-05-302-202/+3
| | | | | | | | Run `make kernel_oldconfig CONFIG_TARGET=subtarget` This mostly aims at getting rid of redundant/unneeded symbols. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: add missing symbol CONFIG_AHCI_XGENEYangbo Lu2021-05-303-1/+2
| | | | | | | | Add missing symbol CONFIG_AHCI_XGENE. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [also add for 5.10, remove from layerscape target config] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.123John Audia2021-05-292-3/+3
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.122John Audia2021-05-291-2/+2
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* scripts: config.guess: update to 2021-05-24Paul Spooren2021-05-292-498/+788
| | | | | | | | | | | | This script hasn't seen an update in multiple years, update it to the latest version provided upstream. Both `config.guess` and `config.sub` are copied from upstream[1] and not modified. The full changelog is available within the upstream repository[1]. [1]: https://git.savannah.gnu.org/git/config.git Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: bump 5.10 to 5.10.41Kevin Darbyshire-Bryant2021-05-291-2/+2
| | | | | | | | No patches needed refreshing. Tested-on: X86_64 APU2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* hostapd: update to version 2021-05-22Adrian Schmutzler2021-05-291-4/+4
| | | | | | | | | | | This update only adds one commit: b102f19bcc53 tests: Opportunistic Wireless Encryption - SA Query The main reason for the bump is to have a newer PKG_SOURCE_DATE, so we can reset PKG_RELEASE to 1 (this has not been done for the most recent bump), and replace it with AUTORELEASE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: simplify setting device MACRafał Miłecki2021-05-281-11/+8
| | | | | | | | | | | | | | 1. Move code above interface generation It results in more logical order. Device gets its config section above interface section. 2. Drop the loop We have separated code handling bridges now so $device should be guaranteed to contain a single device name. 3. Drop section name It's not required by netifd or LuCI & it's not needed by this script as $device contains a single device name now. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ubox: fix init script validation of log_ip optionJo-Philipp Wich2021-05-282-2/+2
| | | | | | | | The underlying logread process uses usock() to handle remote connections which is able to handle both hostnames and IP addresses. Ref: https://github.com/openwrt/luci/issues/5077 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add support for Wavlink WL-WN578A2Thomas Aldrian2021-05-284-3/+182
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug wireless router. This device is also sold under the name SilverCrest SWV 733 A2. Device Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high - Buttons: Reset, WPS - Sliding mode switch: AP, repeater, client - Small sliding power switch Flashing instructions: U-Boot launches TFTP client if WPS button is pressed during power-on. Configure as follows: - Server IP: 192.168.10.100 - Filename (rename sysupgrade file to this): firmware.bin Flashing should not take more than a minute, device will reboot automatically. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* kernel: bump 5.10 to 5.10.40Rui Salvaterra2021-05-273-4/+4
| | | | | | | | Automatically refreshed: generic/hack-5.10/902-debloat_proc.patch generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* hostapd: support verbose build using V=scFelix Fietkau2021-05-271-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* base-files: generate network config with "device" optionsRafał Miłecki2021-05-274-22/+22
| | | | | | | Replace "ifname" with "device" as netifd has been recently patches to used the later one. It's more clear and accurate. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* hostapd: ACS: fix channel 100 frequencyDavid Bauer2021-05-262-1/+31
| | | | | | | | | | | Channel 100 is a valid channel to choose for 80MHz operation. However, it's assigned to 5500 MHz, not 5550MHz. In fact, there is no channel assigned to this frequency. Fix this obbvious typo to allow ACS to select channel 100 for 80 MHz operation again. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add missing v5.4 SPI chipselect patchDavid Bauer2021-05-261-0/+26
| | | | | | | | | The patch was not applied to the v5.4 target, thus breaking Kernel 5.4 on devices with multiple flash chips attache to the SPI bus. Fixes commit bd54e739541b ("ath79: set number of chipselect lines") Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: fix AutoLoad parameter for uleds moduleEvgeny Kolesnikov2021-05-261-1/+1
| | | | | | | | The name of the module is 'uleds', not 'leds-uleds'. Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com> [improve commit title] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for JCG Q20Chukun Pan2021-05-266-0/+201
| | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: add support for cudy WR2100Leon M. George2021-05-263-0/+218
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications SoC: MT7621 CPU: 880 MHz Flash: 16 MiB RAM: 128 MiB WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac MT7603E / MT7615E Ethernet: 5x Gbit ports Installation There are two known options: 1) The Luci-based UI. 2) Press and hold the reset button during power up. The router will request 'recovery.bin' from a TFTP server at 192.168.1.88. Both options require a signed firmware binary. The openwrt image supplied by cudy is signed and can be used to install unsigned images. R4 & R5 need to be shorted (0-100Ω) for the UART to work. Signed-off-by: Leon M. George <leon@georgemail.eu> [remove non-required switch-port node - remove trgmii phy-mode] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for TP-Link Archer C6U v1 (EU)Georgi Vlaev2021-05-264-1/+264
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6U v1 (EU). The device is also known in some market as Archer C6 v3. This patch supports only Archer C6U v1 (EU). Specifications: -------------- * SoC: Mediatek MT7621AT 2C2T, 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (Winbond 25Q128) * WiFi 5GHz: Mediatek MT7613BEN (2x2:2) * WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) * Ethernet: MT7630, 5x 1000Base-T. * LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB * Buttons: Reset, WPS. * UART: Serial console (115200 8n1), J1(GND:3) * USB: One USB2 port. Installation: ------------ Install the OpenWrt factory image for C6U is from the TP-Link web interface. 1) Go to "Advanced/System Tools/Firmware Update". 2) Click "Browse" and upload the OpenWrt factory image: openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin. 3) Click the "Upgrade" button, and select "Yes" when prompted. Recovery to stock firmware: -------------------------- The C6U bootloader has a failsafe mode that provides a web interface (running at 192.168.0.1) for reverting back to the stock TP-Link firmware. The failsafe interface is triggered from the serial console or on failed kernel boot. Unfortunately, there's no key combination that enables the failsafe mode. This gives us two options for recovery: 1) Recover using the serial console (J1 header). The recovery interface can be selected by hitting 'x' when prompted on boot. 2) Trigger the bootloader failsafe mode. A more dangerous option is force the bootloader into recovery mode by erasing the OpenWrt partition from the OpenWrt's shell - e.g "mtd erase firmware". Please be careful, since erasing the wrong partition can brick your device. MAC addresses: ------------- OEM firmware configuration: D8:07:B6:xx:xx:83 : 5G D8:07:B6:xx:xx:84 : LAN (label) D8:07:B6:xx:xx:84 : 2.4G D8:07:B6:xx:xx:85 : WAN Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
* ramips: add support for TP-Link Archer A6 v3Vinay Patil2021-05-264-1/+244
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the TP-Link Archer A6 v3 The router is sold in US and India with FCC ID TE7A6V3 Specification ------------- MediaTek MT7621 SOC RAM: 128MB DDR3 SPI Flash: W25Q128 (16MB) Ethernet: MT7530 5x 1000Base-T WiFi 5GHz: Mediatek MT7613BE WiFi 2.4GHz: Mediatek MT7603E UART/Serial: 115200 8n1 Device Configuration & Serial Port Pins --------------------------------------- ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN _______________________ | | Serial Pins: | VCC GND TXD RXD | |_____________________| LEDs: Power Wifi2G Wifi5G LAN WAN Build Output ------------ The build will generate following set of files [1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin [2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin [3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin How to Use - Flashing from TP-Link Web Interface ------------------------------------------------ * Go to "Advanced/System Tools/Firmware Update". * Click "Browse" and upload the OpenWrt factory image: factory.bin[2] * Click the "Upgrade" button, and select "Yes" when prompted. TFTP Booting ------------ Setup a TFTP boot server with address 192.168.0.5. While starting U-boot press '4' key to stop autoboot. Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin From u-boot command prompt run tftpboot followed by bootm. Recovery -------- Archer A6 V3 has recovery page activated if SPI booting from flash fails. Recovery page can be activated from serial console only. Press 'x' while u-boot is starting Note: TFTP boot can be activated only from u-boot serial console. Device recovery address: 192.168.0.1 Thanks to: Frankis for Randmon MAC address fix. Signed-off-by: Vinay Patil <post2vinay@gmail.com> [remove superfluous factory image definition, whitespacing] Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: sync nl80211.h with upstream and backport a WPA3 related commitFelix Fietkau2021-05-266-35/+659
| | | | | | Fixes compatibility issues with the latest hostapd update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* imx6: image: drop BOOT_SCRIPT and fix DEVICE_NAMEPiotr Dymacz2021-05-262-14/+3
| | | | | | | | | | | | | | This fixes Gateworks Ventana 'DEVICE_NAME' variable which value wasn't adjusted during migration to common 'vendor_model' image naming scheme (fixes: FS#3825). Furthermore, drop unused 'Build/boot-scr' recipe, get rid of redundant 'BOOT_SCRIPT' variable (use already provided 'DEVICE_NAME' instead) and drop custom 'DEVICE_NAME' variable from SolidRun CuBox-i image recipe (use default one instead). Fixes: cbc8bcfbaa ("imx6: image: use vendor_model scheme") Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* mac80211: add more HE capabilitiesFelix Fietkau2021-05-261-5/+81
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix center freq selection for 6 GHzFelix Fietkau2021-05-261-6/+20
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: fix adding back stations after a missed deauth/disassocFelix Fietkau2021-05-263-11/+37
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: update to version 2021-05-21Felix Fietkau2021-05-2653-2295/+238
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 00:07:22 +0000