aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: use nand_do_upgrade for netis WF-2881Sungbo Eo2020-02-073-3/+19
| | | | | | | | | | WF-2881 sysupgrade image uses UBI rootfs, but still relies on default_do_upgrade. Because of this, config backup is not restored after sysupgrade. It can be fixed by switching to nand_do_upgrade and sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar properly, so one should use factory image to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: add LED trigger for TL-WR902AC v1 WAN LEDLech Perczak2020-02-071-0/+1
| | | | | | | | | | | Inspired by commit c48b571ad708, add an LED trigger for the WAN LED on top of the TP-Link TL-WR902AC v1. Currently, only the LED on the port itself shows the link state, while the LED on top of the device stays dark. The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at the port was labeled LAN. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for Atheros AR934x HS UARTDaniel Golle2020-02-072-0/+65
| | | | | | | | | AR934x chips also got the 'old' qca,ar9330-uart in addition to the 'new' ns16550a compatible one. Add support for UART1 clock selector as well as device-tree bindings in ar934x.dtsi to make use of that uart. Reported-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDEDaniel Golle2020-02-071-0/+64
| | | | | | | | | | | | | | | | On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x does not do any harm, so just set them unconditionally. Tested-by: Chuanhong Guo <gch981213@gmail.com Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm53xx: build images for Luxul ABR-4500 and XBR-4500 routersDan Haab2020-02-072-0/+37
| | | | | | | | Luxul ABR-4500 and XBR-4500 devices are wired routers with 5 Ethernet ports and 1 USB 3.0 port. Flashing requires using Luxul firmware 6.4.0 or newer and uploading firmware using "Firmware Update" web UI page. Signed-off-by: Dan Haab <dan.haab@legrand.com>
* firmware-utils: add lxlfw tool for generating Luxul firmwaresDan Haab2020-02-072-0/+283
| | | | | | It's a simple tool prepending image with a Luxul header. Signed-off-by: Dan Haab <dan.haab@legrand.com>
* ath79: ag71xx: use netif_receive_skb_list on 4.19Chuanhong Guo2020-02-071-1/+19
| | | | | | | | This new function make batch processing of network packets possible, which slightly improves performance. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Tested-by: Rosen Penev <rosenp@gmail.com>
* kernel: remove duplicate flash chip definitionDaniel Golle2020-02-062-18/+16
| | | | | | | XTX XT25F128A shares it's chip ID with XM25QH128A which got identical features. Hence there it makes no sense to add it to the driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: use ar934x-spi for ar933x as wellChuanhong Guo2020-02-061-3/+2
| | | | | | | | ar933x appears to have the same spi controller as ar934x but it's not mentioned in datasheet at all. Use new spi driver instead to gain more flash operating performance. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add new ar934x spi driverChuanhong Guo2020-02-0611-15/+346
| | | | | | | | | | | A new shift mode was introduced since ar934x which has a way better performance than current bitbang driver and can handle higher spi clock properly. This commit adds a new driver to make use of this new feature. This new driver has chipselect properly configured and we don't need cs-gpios hack in dts anymore. Remove them. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mac80211: brcm: backport remaining 5.6 kernel patchesRafał Miłecki2020-02-0610-3/+651
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* wireguard: bump to 0.0.20200205Jason A. Donenfeld2020-02-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | | * compat: support building for RHEL-8.2 * compat: remove RHEL-7.6 workaround Bleeding edge RHEL users should be content now (which includes the actual RedHat employees I've been talking to about getting this into the RHEL kernel itself). Also, we remove old hacks for versions we no longer support anyway. * allowedips: remove previously added list item when OOM fail * noise: reject peers with low order public keys With this now being upstream, we benefit from increased fuzzing coverage of the code, uncovering these two bugs. * netns: ensure non-addition of peers with failed precomputation * netns: tie socket waiting to target pid An added test to our test suite for the above and a small fix for high-load CI scenarios. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* ramips: add support for I-O DATA WN-AX1167GR2INAGAKI Hiroshi2020-02-054-0/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR2 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-AX1167GR2 normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D42 (COMB) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-DX1167RINAGAKI Hiroshi2020-02-056-4/+268
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: extend and rename wr1201-factory-headerINAGAKI Hiroshi2020-02-051-14/+16
| | | | | | | | | | | | | | | | | | | | | This commit adds the ability to set custom uImage magic to Build/wr1201-factory-header and renames it to "Build/custom-initramfs-uimage". Custom uImage header in initramfs image is required on following devices: - I-O DATA WN-AX1167GR2 - I-O DATA WN-AX2033GR - I-O DATA WN-AX2033GR2 - I-O DATA WN-DX1167R While at it, fix typo in comment. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run> [shorten commit title, minor commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "iwinfo: update to latest Git HEAD"Jo-Philipp Wich2020-02-052-3/+12
| | | | | | | | | This reverts commit 96424c143dd818b391d9b8da18249eca1d2e6c83. The commit changed libiwinfo's internal ABI which breaks a number of downstream projects, including LuCI and rpcd-mod-iwinfo. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* procd: support 'requirejail' attributeKevin Darbyshire-Bryant2020-02-042-2/+3
| | | | | | | | | | | | | | | | Bump procd package to reduce log spam related to missing jail binaries in a non-jail capable system. bcb8655 instance: add 'requirejail' attribute An additional jail attribute 'requirejail' can now be used to indicate mandatory use of a jailed environment and hence prevent process startup in the event that the jail subsystem is unavailable. Procd will now only log errors if jail is unavailable and 1) is a mandatory requirement or 2) a procd debug level of at least 2 is in use. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* iwinfo: update to latest Git HEADDavid Bauer2020-02-042-12/+3
| | | | | | | | | eba5a20 iwinfo: add device id for BCM43602 a6914dc iwinfo: add BSS load element to scan result bb21698 iwinfo: add device id for Atheros AR9287 7483398 iwinfo: add device id for MediaTek MT7615E Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm2708: update to latest patches from RPi foundationÁlvaro Fernández Rojas2020-02-04618-65/+3580
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm2708-gpu-fw: update to latest firmwareÁlvaro Fernández Rojas2020-02-041-15/+15
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: add support for GD25D05 SPI NORKoen Vandeputte2020-02-043-0/+87
| | | | | | | | | | | | | | | | | | | | | | This chip is used on newer RB912UAG-5HPnD r2 boards: Before: [ 0.642553] m25p80 spi0.0: unrecognized JEDEC id bytes: c8, 40, 10 [ 0.649381] NAND flash driver for the RouterBOARD 91x series After: [ 0.641714] m25p80 spi0.0: found gd25d05, expected m25p80 [ 0.649916] m25p80 spi0.0: gd25d05 (64 Kbytes) [ 0.655122] Creating 4 MTD partitions on "spi0.0": [ 0.660164] 0x000000000000-0x00000000c000 : "routerboot" [ 0.667782] 0x00000000c000-0x00000000d000 : "hard_config" [ 0.675073] 0x00000000d000-0x00000000e000 : "bios" [ 0.682613] 0x00000000e000-0x00000000f000 : "soft_config" [ 0.690304] NAND flash driver for the RouterBOARD 91x series Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.101Koen Vandeputte2020-02-0440-408/+88
| | | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14896 - CVE-2019-14897 Remove upstreamed: - 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch - 950-0202-staging-bcm2835-camera-fix-module-autoloading.patch - 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.169Koen Vandeputte2020-02-0427-327/+80
| | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14896 - CVE-2019-14897 Remove upstreamed: - 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch - 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: remove unnecessary execute permission bitSungbo Eo2020-02-041-0/+0
| | | | | | | | dts file does not need to be executable. 644 is enough. Fixes: f098c612b6db ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* mediatek: remove unnecessary execute permission bitSungbo Eo2020-02-043-0/+0
| | | | | | | | kernel config and patch files do not need to be executable. 644 is enough. Fixes: 01c8f2e97cc6 ("mediatek: bump to v4.19") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* uboot-envtools: ath79: add Netgear WNDR3700v2Michal Cieslakiewicz2020-02-041-1/+2
| | | | | | | | Add Netgear WNDR3700v2 to the list of supported boards. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> [rebase, adjusted commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: WNDR3700 v1/v2: make u-boot env partition writableMichal Cieslakiewicz2020-02-042-2/+0
| | | | | | | Remove read-only flag from U-boot environment partition for Netgear WNDR3700 v1 and v2 so u-boot-envtools can modify data there. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* mediatek: remove KERNEL_PATCHVER overwrite for mt7629Adrian Schmutzler2020-02-041-1/+0
| | | | | | | | Since whole target has been bumped to kernel 4.19 in 01c8f2e97cc6 ("mediatek: bump to v4.19") we do not need the overwrite in mt7629 subtarget anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: bump to v4.19John Crispin2020-02-044-1/+562
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* bcm4xxx: fix iwinfo behaviourJohn Crispin2020-02-042-0/+163
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ath79: add support for COMFAST CF-E560ACAugust Huber2020-02-035-6/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the COMFAST CF-E560AC, an ap143 based in-wall access point. Specifications: - SoC: Qualcomm Atheros QCA9531 - RAM: 128 MB DDR2 (Winbond W971GG6SB-25) - Storage: 16 MB NOR (Winbond 25Q128JVSO) - WAN: 1x 10/100 PoE ethernet (48v) - LAN: 4x 10/100 ethernet - WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM - WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM - USB: one external USB2.0 port - UART: 3.3v, 2.54mm headers already populated on board - LED: 7x external - Button: 1x external - Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod) MAC addressing: - stock LAN *:40 (label) WAN *:41 5G *:42 2.4G *:4a - flash (art partition) 0x0 *:40 (label) 0x6 *:42 0x1002 *:41 0x5006 *:43 This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and 0x5006, however the vendor firmware only reads from art:0x0 for the LAN interface and then increments in 02_network. They also jump 8 addresses for the second wifi interface (2.4 GHz). This behavior has been duplicated in the DTS and ath10k hotplug to align addresses with the vendor firmware v2.6.0. Recovery instructions: This device contains built-in u-boot tftp recovery. 1. Configure PC with static IP 192.168.1.10/24 and tftp server. 2. Place desired image at /firmware_auto.bin at tftp root. 3. Connect device to PC, and power on. 4. Device will fetch flash from tftp, flash and reboot into new image. Signed-off-by: August Huber <auh@google.com> [move jtag_disable_pins, remove unnecessary statuses in DTS, remove duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: WNDR3700 v2: add dash before version in device nameMichal Cieslakiewicz2020-02-034-9/+9
| | | | | | | | Adapt Netgear WNDR3700v2 device identification string to ath79 naming scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config, makefile, init scripts and device tree definition). Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* mt76: update to the latest versionFelix Fietkau2020-02-021-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 8f33a1e936fd mt76: mt7615: report firmware log event messages 43db699b1ad8 mt76: mt7615: increment the MAC address of the secondary PHY (DBDC) 161d1c73c62a mt7615: use local MAC address for the second PHY 9453dbe921b9 mt76: set dma-done flag for flushed descriptors 65745c5ac503 mt76: fix handling full tx queues in mt76_dma_tx_queue_skb_raw 14f37f8d86eb mt76: dma: do not write cpu_idx on rx queue reset until after refill 99ce68625473 mt76: mt7603: increase dma mcu rx ring size 62c447e2c75f mt76: enable Airtime Queue Limit support 1c258940d818 mt76: mt7615: report TSF information 2d22ef618712 mt76: mt7615: add per-phy mib statistics 8d690f3bfbc4 mt76: mt7615: add a get_stats() callback b06177ce387c mt76: move dev_irq tracepoint in mt76 module 5ac9889c33f1 mt76: move mac_txdone tracepoint in mt76 module 7801ebd775e3 mt76: mt7615: add tracing support fd877a17cc0a mt76: mt76x2: get rid of leftover target 039471502578 mt76: mt7615: initialize radar specs from host driver b208305e6275 mt76: mt7615: fix endianness in mt7615_mcu_set_eeprom fd1fa6860666 mt76: move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76_phy_init c94afbe3d70a mt76: mt7615: remove leftover routine declaration 29fec3a9b0b4 mt76: rely on mac80211 utility routines to compute airtime 2bb518752b3f mt76: mt76x02u: avoid overwrite max_tx_fragments a0f1ff0473b5 mt76: mt76u: check tx_status_data pointer in mt76u_tx_tasklet a5dca118bf40 mt76: mt76u: add mt76u_process_rx_queue utility routine 06caaf0d33b4 mt76: mt76u: add mt76_queue to mt76u_get_next_rx_entry signature cf8e2590e46b mt76: mt76u: add mt76_queue to mt76u_refill_rx signature 0077b30ce2c8 mt76: mt76u: use mt76_queue as mt76u_complete_rx context 06d466b86981 mt76: mt76u: add queue id parameter to mt76u_submit_rx_buffers 580ddd175eee mt76: mt76u: move mcu buffer allocation in mt76x02u drivers acc227e14d95 mt76: mt76u: introduce mt76u_free_rx_queue utility routine aa28404bf287 mt76: mt76u: stop/free all possible rx queues 885fe4a29bb9 mt76: mt76u: add mt76u_alloc_rx_queue utility routine c85dec848303 mt76: mt76u: add queue parameter to mt76u_rx_urb_alloc ca7991699109 mt76: mt76u: resume all rx queue in mt76u_resume_rx e2a39697fb0a mt76: mt76u: introduce mt76u_alloc_mcu_queue utility routine 39fb59ce927b mt76: mt76u: add {read/write}_extended utility routines 8c6cf328eb1f mt76: mt76u: take into account different queue mapping for 7663 e742618fc5ce mt76: mt76u: introduce mt76u_skb_dma_info routine 23b3328e52fe mt76: mt76u: add endpoint to mt76u_bulk_msg signature 82bedb294534 mt76: mt76u: introduce MT_DRV_RX_DMA_HDR flag 2db2bab099d0 firmware: update mt7615 N9 firmware to 20200107155603 60e27689603d firmware: update MT7615 CR4 firmware to 20190121161307 d15a4bbb3f69 mt76: mt7615: add __aligned(4) to txp structs 1c4ff4f2dc7f mt76: mt7615: move mmio related code from pci.c to mmio.c 51b1eb7a4902 mt76: mt7615: split up firmware loading functions f84b590b6454 mt76: mt7615: store N9 firmware version instead of CR4 92bafd4b1bfc mt76: mt7615: fix MT_INT_TX_DONE_ALL definition for MT7622 13a4269a1bfa mt76: mt7615: add dma and tx queue initialization for MT7622 ab94a85efb18 mt76: mt7615: add eeprom support for MT7622 f0b02d8115b0 mt76: mt7615: add calibration free support for MT7622 fd3ae9a342ae mt76: mt7615: disable 5 GHz on MT7622 80d3681b404d mt76: mt7615: implement probing and firmware loading on MT7622 79808e62324e mt76: mt7615: implement DMA support for MT7622 bddcbb25cd0e mt76: mt7615: decrease rx ring size for MT7622 6cd5c381eaee mt76: mt7615: disable DBDC on MT7622 f66b480434e9 mt76: mt7615: add Kconfig entry for MT7622 68f38eea39b5 firmware: add firmware for MT7622 built-in WiFi 7882bbd25c38 mt76: mt7615: fix and rework tx power handling 0f06914acfb4 mt76: mt7615: implement hardware reset support db97358df47e mt76: mt7615: add support for testing hardware reset b9d9f91b1522 mt76: mt7615: fix adding active monitor interfaces fd216cb5b2f9 mt76: mt7615: fix monitor mode on second PHY 269de7c22957 firmware: fix version number for upcoming mt7615 mcu v2 support patches 9f8c6c4a20b4 mt76: mt7615: simplify mcu_set_bmc flow ff32af25f83e mt76: mt7615: simplify mcu_set_sta flow f16433cd7889 mt76: mt7615: add a helper to encapsulate sta_rec operation 77b9d8586307 mt76: mt7615: add starec operating flow for firmware v2 170b21f9ec78 mt76: mt7615: use new tag sta_rec_wtbl 648ce1aaa493 mt76: mt7615: switch mt7615_mcu_set_tx_ba to v2 format 721673759d82 mt76: mt7615: switch mt7615_mcu_set_rx_ba to v2 format Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add wmac devicetree node for MT7622John Crispin2020-02-021-0/+11
| | | | | Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uci: update to version 2020-01-27Hans Dedecker2020-02-021-5/+4
| | | | | | | e8d8373 file: fix segfault in uci_parse_option aa5e77a file: fix segfault in uci_parse_config Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: hwmon: package mcp3021 moduleDaniel Golle2020-02-021-0/+15
| | | | | | | Package kernel module for Linear Technology MCP3021/3221 I2C connected current and voltage monitor chips. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add common definition for Device/tplink-v2Adrian Schmutzler2020-02-022-8/+13
| | | | | | | | | | | | | | | | This adds a shared definition Device/tplink-v2 to common-tp-link.mk. Though currently only one device in ath79 uses it, putting it in the common file seems more organized. The definitions are based on the implementation in ramips target, where a lot of devices is using tplink-v2-* commands already. The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because it's default in Build/tplink-v2-image anyway. While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS, which seems to have been overlooked when adding Archer D50 v1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename tplink-loader-okli to tplink-safeloader-okliAdrian Schmutzler2020-02-022-10/+10
| | | | | | | | | This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli since the latter more accurately describes the combination of tplink-safeloader and loader-okli use there. The old version might be confused with other uses of the okli loader. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename Device/tplink to Device/tplink-v1Adrian Schmutzler2020-02-021-6/+6
| | | | | | | | | As we have tplink-v2-header and tplink-v2-image recipes as well, this patch renames the Device/tplink definition to Device/tplink-v1, as it's using the tplink-v1-* commands. This should provide easier distinction in the future. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: image: align subtargets makefile namesTomasz Maciej Nowak2020-02-014-3/+3
| | | | | | | Align subtargets makefiles names to actual subtargets. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: image: sort devices alphabeticallyTomasz Maciej Nowak2020-02-012-114/+114
| | | | | | | | This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE200 v2Andreas Böhler2020-02-016-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:0D 2.4G: *:0E 5G : *:0F Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Additonal notes --------------- It is possible to flash back to stock by using tplink-safeloader to create a sysupgrade image based on a stock update. After the first boot, it is necessary upgrade to another stock image, otherwise subsequent boots fail with LZMA ERROR 1 and you have to attach serial to recover the device. Signed-off-by: Andreas Böhler <dev@aboehler.at> [remove DEVICE_VARS change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: collect and harmonize TP-Link image variants in common fileAdrian Schmutzler2020-02-014-114/+100
| | | | | | | | | | | | This moves the various variants of common device definitions for TP-Link devices to a common Makefile common-tp-link.mk. This provides the opportunity to reorganize and move parameters between individual device definitions and the common ones. While at it, also use the common definitions for previously independent definitions where appropriate. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* cypress-firmware: update to v4.14.77-2020_0115Álvaro Fernández Rojas2020-02-011-4/+58
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: connmark set-dscpmark follow upstreamimg attemptKevin Darbyshire-Bryant2020-01-313-159/+265
| | | | | | | | | | | | | | I'm having another attempt at trying to getting the 'store dscp into conntrack connmark' functionality into upstream kernel, since the restore function (act_ctinfo) has been accepted. The syntax has changed from 'savedscp' to 'set-dscpmark' since that conforms more closely with existing functionality. 4.14 backport is more of a hack since the structure versioning mechanism isn't in place. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* iptables: set-dscpmark follow upstreamimg attemptKevin Darbyshire-Bryant2020-01-313-215/+460
| | | | | | | | | | | I'm having another attempt at trying to getting the 'store dscp into conntrack connmark' functionality into upstream kernel, since the restore function (act_ctinfo) has been accepted. The syntax has changed from 'savedscp' to 'set-dscpmark' since that conforms more closely with existing functionality. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: add support for Ubiquiti NanoStation Loco M (XW)Roger Pueyo Centelles2020-01-314-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: do not set inherited phy-mode/status properties againAdrian Schmutzler2020-01-3114-22/+2
| | | | | | | | | There are several cases where phy-mode and status properties are set again in DTS(I) files although those were set to the same values in parent DTSI files already. Remove those cases (and thus also stop their proliferation by copy/paste). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: harmonize ethernet-phy naming schemeAdrian Schmutzler2020-01-316-15/+25
| | | | | | | | | | | A minority of ethernet-phy definitions seems to use numbers in label, name and reg property relatively random. This patch aligns their use to have the same numeric value for all of them. While at it, improve order of properties/add newlines for the ethX nodes where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: mt7623: remove left-over fragments of mt7623a-rfb-emmcAdrian Schmutzler2020-01-303-468/+2
| | | | | | | | | | | | | | The image creation for the mt7623a-rfb-emmc has been removed during a patch refresh without specific comment. The corresponding base-files entries and DTS patches for 4.14 are still there. Since mt7623 is pretty dead and nobody has missed this device, let's just remove the rest. Fixes: 050da2107a7e ("mediatek: backport upstream mediatek patches") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 18:34:13 +0000