aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* libnetfilter-conntrack: bump to 1.0.9Stijn Tintel2022-02-171-2/+2
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Jo-Philipp Wich <jo@mein.io>
* ath25: drop Linux 5.4 supportRui Salvaterra2022-02-1713-3843/+0
| | | | | | We've been bumped to 5.10, no need to carry this stuff anymore. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: fix NAND flash driver ECC bit position maskFelix Fietkau2022-02-161-1/+1
| | | | | | | | The bit position mask was accidentally made too wide, overlapping with the LSB from the byte position mask. This caused ECC calculation to fail for odd bytes Signed-off-by: Chad Monroe <chad.monroe@smartrg.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport fix for initializing skb->cb in the bridge code to 5.4Felix Fietkau2022-02-162-2/+30
| | | | | | Fixes issues with proxyarp Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm4908: backport watchdog and I2C changesRafał Miłecki2022-02-1616-26/+282
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mt76: update to the latest versionFelix Fietkau2022-02-151-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ddd3c2f38b30 mt76: redefine mt76_for_each_q_rx to adapt mt7986 changes 7fa5229a4228 mt76: improve signal strength reporting 025a72cd2d24 mt76: mt7915: fix injected MPDU transmission to not use HW A-MSDU 8c765fd92d97 mt76: mt7615: introduce SAR support 799a15bb68f9 mt76: fix endianness errors in reverse_frag0_hdr_trans c114919f0c08 mt76: mt7915: Fix channel state update error issue 93191a37e59a mt76: mt7915: fix potential memory leak of fw monitor packets cde589b2efb7 mt76: mt7921s: fix missing fc type/sub-type for 802.11 pkts 6ef22f4dc4e4 mt76: mt7915: add support for MT7986 7f1818cd8f2d mt76: mt7915: introduce band_idx in mt7915_phy 1d57a0d506db mt76: mt7915: initialize smps mode in mt7915_mcu_sta_rate_ctrl_tlv() 1f2a4816a3de mt76: mt7615: fix compiler warning on frame size d60f335e785b mt76: mt7915: fix endianness warnings in mt7915_debugfs_rx_fw_monitor d0ab636cb61c mt76: mt7915: fix endianness warnings in mt7915_mac_tx_free() 9d9bd7b3c48c mt76: connac: adjust wlan_idx size from u8 to u16 be1091f1172d mt76: mt7615: Fix assigning negative values to unsigned variable d4fc42889a30 mt76: mt7915: check band idx for bcc event 98ee3e2889ea mt76: mt7915: fix logic error and remove the unused member of mt7915_dev bbbbafb67bac mt76: mt7915: fix compiler warning abd80cf68db1 mt76: mt7915: fix the muru tlv issue a050c14b5631 mt76: mt7915: use min_t() to make code cleaner 9fee8f3736eb mt76: mt7915e: Fix degraded performance after temporary overheat f2e1a62cf0d0 mt76: mt7915e: Add a hwmon attribute to get the actual throttle state. c67df0d3130a mt76: mt7915e: Enable thermal management by default Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix traffic stalls on forwarded mesh packets due to wrong AC selectionFelix Fietkau2022-02-151-0/+50
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* feeds: use git-src-full to allow Git versioningPaul Spooren2022-02-152-9/+9
| | | | | | | | | | | | | | | Both $(AUTORELEASE) and $(PKG_SRC_VERSION) (from luci.git) use the Git log to determine releases and package timestamps. Feeds are shallow cloned by default, resulting in an incomplete Git log and therefore different local package versions than offered upstream. This commits sets the default feeds to use `src-git-full` to solve that. Add fixes from "2b1d92f: scripts/feeds: silence git warning by selecting pull style" to `src-git-full` Signed-off-by: Paul Spooren <mail@aparcar.org>
* build: store source_date_epoch as integerPaul Spooren2022-02-141-1/+1
| | | | | | | | | The value is retreived from a env variable which defaults to be read as a string. However the SOURCE_DATE_EPOCH is a unix timestamp aka integer. Fix this to allow downstream tools to parse the value directly. Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: fix a race condition leading to a crash in hw flow offloadingFelix Fietkau2022-02-141-5/+6
| | | | | | | flowtable->net was initialized too late, and this could be triggered even without hardware offload support on the device Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix copy&paste mistake in bridge offload codeFelix Fietkau2022-02-141-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621: do memory detection on KSEG1Chuanhong Guo2022-02-141-0/+58
| | | | | | | | | | | | | | | | | | | | It's reported that current memory detection code occasionally detects larger memory under some bootloaders. Current memory detection code tests whether address space wraps around on KSEG0, which is unreliable because it's cached. Rewrite memory size detection to perform the same test on KSEG1 instead. While at it, this patch also does the following two things: 1. use a fixed pattern instead of a random function pointer as the magic value. 2. add an additional memory write and a second comparison as part of the test to prevent possible smaller memory detection result due to leftover values in memory. Fixes: 6d91ddf517 ("ramips: mt7621: add support for memory detection") Reported-by: Rui Salvaterra <rsalvaterra@gmail.com> Tested-by: Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* procd: simplify uxc init scriptDaniel Golle2022-02-131-7/+1
| | | | | | | | 'uxc boot' is inteded to be called multiple times, so there is not need to guard the first call on boot -- the actual code anyway didn't do that, so just remove it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: remove 640-bridge-only-accept-EAP-locally.patchFelix Fietkau2022-02-122-164/+0
| | | | | | | The issue of EAP frames sent to group address (or the wrong address) has been addressed in mac80211, so this hack is no longer needed Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add a fast path for the bridge codeFelix Fietkau2022-02-122-4/+821
| | | | | | | | | This caches flows between MAC addresses on separate ports, including their VLAN in order to bypass the normal bridge forwarding code. In my test on MT7622, this reduces LAN->WLAN bridging CPU usage by 6-10%, potentially even more on weaker platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tcpdump: Fix CVE-2018-16301Hauke Mehrtens2022-02-122-1/+102
| | | | | | | | | | | This fixes the following security problem: The command-line argument parser in tcpdump before 4.99.0 has a buffer overflow in tcpdump.c:read_infile(). To trigger this vulnerability the attacker needs to create a 4GB file on the local filesystem and to specify the file name as the value of the -F command-line argument of tcpdump. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: fix rekey failure in drivers with 802.3 decap offloadFelix Fietkau2022-02-121-0/+43
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* firewall4: update to latest Git HEADJo-Philipp Wich2022-02-121-3/+3
| | | | | | | | | | | | | 53caa1a fw4: resolve zone layer 2 devices for hw flow offloading 9fe58f5 fw4: rework and fix family inheritance logic 8795296 tests: mocklib: fix infinite recursion in wrapped print() 281b1bc tests: change mocked wan interface type to PPPoE 93b710d tests: mocklib: forward compatibility change 1a94915 fw4: only stage reflection rules if all required addrs are known 5c21714 fw4: add device iifname/oifname matches to DSCP and MARK rules 3eacc97 tests: adjust 01_ruleset test case to latest changes Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ucode: update to latest Git HEADJo-Philipp Wich2022-02-121-3/+3
| | | | | | | | a29bad9 compiler: fix patchlist corruption on switch statement syntax errors 86f0662 lib: change `ord()` to always return single byte value 116a8ce vallist: fix storing/retrieving short strings with 8bit byte value Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: bump 5.10 to 5.10.100John Audia2022-02-117-11/+11
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.99John Audia2022-02-116-58/+7
| | | | | | | | | | | | | | | | | | | | Had to update generic defconfig (make kernel_menuconfig CONFIG_TARGET=generic) for this bump, but since that only modifies the target defined in .config, and since that target also needed to be updated for unrelated reasons, manually propagated the newly added symbol to the generic config. Removed upstreamed: pending-5.10/860-Revert-ASoC-mediatek-Check-for-error-clk-pointer.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.99&id=080f371d984e8039c66db87f3c54804b0d172329 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.98John Audia2022-02-1126-92/+68
| | | | | | | | | | | | | Manually rebased: bcm27xx/patches-5.10/950-0675-drm-vc4-hdmi-Drop-devm-interrupt-handler-for-CEC-int.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* ramips: add support for ELECOM WRC-2533GS2INAGAKI Hiroshi2022-02-112-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GS2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB (NT5CC64M16GP-DI) - Flash : SPI-NOR 16 MiB (MX25L12835FM2I-10G) - WLAN : 2.4/5GHz 4T4R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/Keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-2533GS2 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC Addresses: LAN : 04:AB:18:xx:xx:FB (Factory, 0xFFF4 (hex)) WAN : 04:AB:18:xx:xx:FC (Factory, 0xFFFA (hex)) 2.4 GHz : 04:AB:18:xx:xx:FD (Factory, 0x4 (hex)) 5 GHz : 04:AB:18:xx:xx:FE (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: move MAC configs to device dts from wrc-gs-2pci.dtsiINAGAKI Hiroshi2022-02-117-24/+144
| | | | | | | | | | | | | | | | | | | | | | The locations of MAC addresses in mtd for LAN/WAN on ELECOM WRC-2533GS2 are changed from the other WRC-GS/GST devices with 2x PCIe. So move the related configurations in mt7621_elecom_wrc-gs-2pci.dtsi to dts of each model. - WRC-1750GS - WRC-1750GSV - WRC-1750GST2 - WRC-1900GST - WRC-2533GST - WRC-2533GST2 -> LAN: 0xE000, WAN: 0xE006 - WRC-2533GS2 -> LAN: 0xFFF4, WAN: 0xFFFA Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: update WLAN MAC address of ipTIME A3004TSungbo Eo2022-02-111-0/+6
| | | | | | | | | | | | | | | | Reported MAC addresses: | interface | MAC address | source | comment |-----------|-------------------|----------------|--------- | LAN | 90:xx:xx:18:xx:1F | | [1] | WAN | 90:xx:xx:18:xx:1D | | | WLAN 2G | 92:xx:xx:48:xx:1C | | | WLAN 5G | 90:xx:xx:18:xx:1C | factory 0x4 | | | 90:xx:xx:18:xx:1C | config ethaddr | [1] Used in this patch as WLAN 2G MAC address with the local bit set Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME AX2004MSungbo Eo2022-02-115-0/+197
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: * SoC: MT7621A * RAM: 256 MiB * Flash: NAND 128 MiB * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 5x 1GbE * Switch: SoC built-in * USB: 1x 3.0 * UART: J4 (115200 baud) * Pinout: [3V3] (TXD) (RXD) (GND) MAC addresses: | interface | MAC address | source | comment |-----------|-------------------|----------------|--------- | LAN | 58:xx:xx:00:xx:9B | | [1] | WAN | 58:xx:xx:00:xx:99 | | | WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4 | | WLAN 5G | 5A:xx:xx:40:xx:98 | | | | 58:xx:xx:00:xx:98 | config ethaddr | [1] Used in this patch as WLAN 5G MAC address with the local bit set Load addresses: * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. The stock web interface will flash only on the inactive boot partition, but the recovery web page will always flash on boot partition 1. Installation via recovery mode: 1. Press reset button, power up the device, wait >10s for CPU LED to stop blinking. 2. Upload recovery image through the recovery web page at 192.168.0.1. Revert to stock firmware: 1. Install stock image via recovery mode. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* octeon: switch to Kernel 5.10Paul Spooren2022-02-111-2/+1
| | | | | Acked-by: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Paul Spooren <mail@aparcar.org>
* target/linux: add missing symbolRosen Penev2022-02-111-0/+1
| | | | | | Found when building the qoriq target. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/cmake: add MAKE config variableRosen Penev2022-02-111-1/+2
| | | | | | | | | Makes sure that Ninja from staging_dir is used and nowhere else. Reported by reproducible builds project. Builds have been failing ever since tools/cmake started using Ninja. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* qosify: update to the latest versionFelix Fietkau2022-02-101-3/+3
| | | | | | | | e230e71e0a12 map: fix copy-paste error in codepoints map 580d2ccf89f3 bpf: declare tcp_ports/udp_ports without typedef 8d6c19a81f3f ubus: fix a use-after-free bug Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt7622: linksys-e8450: enable using mt7531 switch irqDaniel Golle2022-02-101-0/+4
| | | | | | | | Turns out the MT7531 switch IRQ line is connected to GPIO#53 just like on the BPi-R64, so this seems to be part of the reference design and will probably apply to most MT7622+MT7531 boards. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mt7622: bpi-r64: enable using mt7531 switch irqDaniel Golle2022-02-101-0/+13
| | | | | | | | | | Now that we support link-state-change interrupts, wire up MT7531 IRQ line which is connected to GPIO#53 according to the schematics [1]. As a result, PHY state no longer needs to be polled on that board. [1]: https://forum.banana-pi.org/t/bpi-r64-mt7622-schematic-diagram-public/10118 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: backport MT7530 IRQ supportDENG Qingfang2022-02-102-0/+428
| | | | | | | | | | | Support MT7530 PHY link change interrupts, and enable for MT7621. For external MT7530, a GPIO IRQ line is required, which is board-specific, so it should be added to each DTS. In case the interrupt-controller property is missing, it will fall back to polling mode. Signed-off-by: DENG Qingfang <dqfext@gmail.com>
* ath25: switch to 5.10 KernelPaul Spooren2022-02-101-1/+1
| | | | | Tested-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: backport MediaTek Ethernet PHY driverDENG Qingfang2022-02-095-0/+163
| | | | | | | | | | | | | | Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and MT7531. Fix some link up/down issues. The errornous check for the PHY mode which broke things with MT7531 has been removed as suggested by patch net: phy: mediatek: remove PHY mode check on MT7531 As a result, things are working fine now on MT7622+MT7531 as well. Signed-off-by: DENG Qingfang <dqfext@gmail.com> Tested-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* meta: drop issue_templateJo-Philipp Wich2022-02-091-13/+0
| | | | | | | The contents do not apply anymore now that the switch to Github issue has been decided. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: generic: select the fq_codel qdisc by defaultRui Salvaterra2022-02-092-101/+4
| | | | | | | | | The kernel configuration allows us to select a default qdisc. Let's do this for 5.10 (as 5.4 is on its way out) and get rid of the hacky patch we've been carrying. Acked-by: Jo-Philipp Wich <jo@mein.io> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ucode: update to latest Git HEADJo-Philipp Wich2022-02-081-4/+4
| | | | | | a317c17 compiler: fix incorrect loop break targets Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: move KERNEL_LOADADDR into Device/DefaultSungbo Eo2022-02-081-1/+1
| | | | | | | | | | | | Commit f4a79148f8cb ("ramips: add support for ipTIME AX2004M") was reverted due to KERNEL_LOADADDR leakage, and it seems the problem can be mitigated by moving the variable definition into Device/Default. By this, KERNEL_LOADADDR redefined in a device recipe will not be leaked into the subsequent device recipes anymore and thus will remain as a per-device variable. Ref: cd6a6e3030ff ("Revert "ramips: add support for ipTIME AX2004M"") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq806x: Enlarge D7800 flash - use netgear partitionMike Lothian2022-02-082-7/+4
| | | | | | | | | | | | | | | | | | | | | | Increase the available flash memory size in Netgear R7800 by repurposing the unused "netgear" partition that is located after the firmware partition. Available flash space for kernel+rootfs+overlay increases by 68 MB from 32 MB to 100 MB. In a typical build, overlay space increases from 15 to 85, increasing the package installation possibilities greatly. Reverting to the OEM firmware is still possible, as the OEM firmware contains logic to initialise the "netgear" partition if its contents do not match expectations. In OEM firmware, "netgear" contains 6 UBI sub-partitions that are defined in /etc/netgear.cfg and initialisation is done by /etc/preinit This is based on https://github.com/openwrt/openwrt/commit/fb8a578aa70572b3e56b64d296e22c2931e77b69 Signed-off-by: Mike Lothian <mike@fireburn.co.uk>
* wireguard-tools: allow generating private_keyLeonardo Mörlein2022-02-081-0/+19
| | | | | | | | | | When the uci configuration is created automatically during a very early stage, where no entropy daemon is set up, generating the key directly is not an option. Therefore we allow to set the private_key to "generate" and generate the private key directly before the interface is taken up. Signed-off-by: Leonardo Mörlein <me@irrelefant.net> Tested-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* hostapd: refresh patchesDavid Bauer2022-02-0830-132/+132
| | | | | | Refresh patches after updating to hostapd v2.10. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: update to v2.10David Bauer2022-02-089-447/+57
| | | | | | | | | | | | | | | | | | Upstreamed patches: 020-mesh-make-forwarding-configurable.patch e6db1bc5da3fd7d5f4dba24aa102543b4749912f 550-WNM-allow-specifying-dialog-token.patch 979f19716539362f8ce60a77bf1b88fdcf5ba8e5 720-ACS-fix-channel-100-frequency.patch 2341585c349231af00cdef8d51458df01bc6965f 741-proxyarp-fix-compilation-with-Hotspot-2.0-disabled.patch 08bdf4f90de61a84ed8f4dd918272dd9d36e2e1f Compile-tested: wpad-wolfssl hostapd-openssl Run-tested: ath79-generic Signed-off-by: David Bauer <mail@david-bauer.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* firewall4: update to latest Git HEADJo-Philipp Wich2022-02-071-3/+3
| | | | | | | a0518b6 fw4: gracefully handle unsupported hardware offloading ac99eba init: fix boot action in init script Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* hostapd: automatically calculate channel center freq on chan_switchFelix Fietkau2022-02-071-0/+34
| | | | | | Simplifies switching to different channels when on >= VHT80 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* rpcd: update to latest Git HEADJo-Philipp Wich2022-02-071-5/+6
| | | | | | | | | 909f2a0 ucode: adjust to latest ucode api 4c532bf ucode: add ucode interpreter plugin 9c6ba38 treewide: adjust ubus object type names 75a96dc build: honour CMake install prefix in hardcoded paths Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uhttpd: update to latest Git HEADJo-Philipp Wich2022-02-073-9/+56
| | | | | | | | | | | | | 2f8b136 main: fix leaking -p/-s argument values 881fd3b ucode: adjust to latest ucode api 8b2868e file: specify UTF-8 as charset for dirlists, add option to override 3a5bd84 main: add ucode options to help text 16aa142 examples: add ucode handler example 3ceccd0 ucode: add ucode plugin support f0f1406 examples: add example Lua handler script 9e87095 listen: avoid invalid memory access Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firewall4: update to latest Git HEADJo-Philipp Wich2022-02-071-3/+3
| | | | | | | | | | | | | b54f462 fw4: parse traffic rules before forwarding rules 4d5af8b fw4: consolidate helper code 300c737 fw4: fix applying zone family restrictions to forwardings eb9c25a tests: implement fs.opendir() mock interface d30ff48 tests: fix mocked fs.popen() trace log 52831a0 fw4: improve flowtable handling 7cb10c8 fw4: disable "flow_offloading_hw" option for now b2241a1 fw4: fix enabling NAT reflection rules for DNATs without explicit family Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ucode: update to latest Git HEADJo-Philipp Wich2022-02-071-3/+3
| | | | | | | | | | | | | | | | | | | | | 11adf0c source: convert source objects into proper uc_value_t type 3a49192 treewide: rework function memory model 7edad5c tests: add functional tests for builtin functions d5003fd lib: fix leaking tokener in uc_json() on parse exception 5d0ecd9 lib: fix infinite loop on empty regexp matches in uc_replace() 3ad57f1 lib: fix infinite loop on empty regexp matches in uc_match() 32d596d lib: fix infinite loop on empty regexp matches in uc_split() 3e3f38d vm: ensure consistent trace output between gcc and clang compiled ucode 3600ded vm: fix leaking function value on call exception 3059295 vm: NULL-initialize pointer to make cppcheck happy 98e59bf source: zero-initialize conversion union to make cppcheck happy 7a65c14 run_tests.sh: change workdir to testcase directory during execution afec8d7 run_tests.sh: support placing supplemental testcase files 3ada6e0 run_tests.sh: always treat outputs as text data 2cb627f program: rename bytecode load/write functions, track path of executed file 1094ffa lib: fix memory leak in uc_require_ucode() Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* netifd: update to latest Git HEADJo-Philipp Wich2022-02-071-3/+3
| | | | | | | | | fd4c9e1 system-linux: expose hw-tc-offload ethtool feature in device status dump 3d76f2e system-linux: add wrapper function for creating link config messages 88af2f1 system-linux: delete bridge devices using netlink 85c3548 system-linux: create bridge devices using netlink Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-19 13:08:26 +0000