aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* at91: drop /etc/config/firewallPaul Spooren2022-01-151-6/+0
| | | | | | | | | | The file can't be part of base files or the base-files and firewall packages collide. Two packages must not provide the same config files without having a defined CONFLICT since it would result in an undeterministic config state depending on what package is installed last. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: add support for ipTIME A6004NS-MSeongUk Moon2022-01-154-176/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A. Specifications: - SoC: MediaTek MT7621A (880MHz, Duel-Core) - RAM: DDR3 256MB - Flash: SPI NOR 16MB (Winbond W25Q128BV) - WiFi: MediaTek MT7615E (2.4GHz, 5GHz) - Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated) - USB: USB 3.0 x1 - UART: [3.3V, TX, RX, GND] (57600 8N1) Installation via web interface: 1. Flash initramfs image using OEM's Firmware Update page. 2. Connect to OpenWrt with an SSH connection to `192.168.1.1`. 3. Perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power on the device and connect the shell through UART. 2. Connect to the shell and press the `t` key on the keyboard. 3. Set fixed IP with `192.168.0.2` with subnet mask `255.255.255.0` 4. Flash image via TFTP to `192.168.0.1` Additional Notes: 1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz. 2. If the 5Ghz frequency is too high, 5Ghz may not work. 3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi). Signed-off-by: SeongUk Moon <antegral@antegral.net> [convert CRLF to LF] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for HUMAX E2Kyoungkyu Park2022-01-154-1/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 64MB - Flash: SPI NOR 8MB (MXIC MX25L6405D) - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610E - Ethernet: 1x 10/100Mbps - Switch: SoC internal - UART: J2 (57600 8N1) - pinout: [3V3] (RXD) (GND) (TXD) Installation and Recovery via TFTP: 1. Connect ethernet cable between Router port and PC Ethernet port. 2. Set your computer to a static IP **192.168.1.1** 3. Turn the device off and wait a few seconds. Hold the WPS button on front of device and insert power. 4. Send a firmware image to **192.168.1.6** using TFTP. You can use any TFTP client. (tftp, curl, Tftpd64...) 5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!** The device will be automatically rebooted. Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
* lantiq: add additional caldata offsetsDavid Bauer2022-01-151-3/+2
| | | | | | | | | | | | | | | It was reported the AVM FritzBox 7430 has different offsets for the caldata depending on the device. Whether this is due to custom bad-block handling or up to the installed bootloader-version is unknown. Try both known caldata offsets like it is already done for the ipq40xx NAND based models. Use the same approach for the FritzBox 7412. While it is currently unknown, whether it is affected, applying the same logic has no downsides. Signed-off-by: David Bauer <mail@david-bauer.net>
* firmware-utils: update to latest masterMatthias Schiffer2022-01-141-3/+3
| | | | | | 84dbf8ee49f5 tplink-safeloader: fix Archer A7v5 factory flashing from vendor fw > v1.1.x Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* lantiq: flag FritzBox 7360 family buttons active-lowDavid Bauer2022-01-141-2/+2
| | | | | | | | All buttons of the FritzBox 7360 family are active-low, not active-high. Corrent the GPIO flag. This fixes release triggers upon push of a button. Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me> Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add op-class to get_status outputDavid Bauer2022-01-141-2/+9
| | | | | | Include the current operation class to hostapd get_status interface. Signed-off-by: David Bauer <mail@david-bauer.net>
* netifd: update to git HEADHans Dedecker2022-01-141-3/+3
| | | | | | 3043206 system: fix compilation with glibc 2.34 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mediatek: mt7623: Enable PCIe bus 0 (and thus SATA) on U7623David Woodhouse2022-01-141-0/+8
| | | | Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* kernel: split kernel version to dedicated filesAnsuel Smith2022-01-133-4/+9
| | | | | | | | | | Move the kernel versions and hash to dedicated files. This makes kernel bump quicker and fix some annoying problem with rebasing when multiple kernel bump are proposed. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [Rebased on top of current master] Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* iptables: enable nftable support by defaultPaul Spooren2022-01-141-2/+2
| | | | | | | | | | | | | | OpenWrt plans to move over to firewall4 which uses nftables under the hood. To allow a smooth migration the package `iptables-nft` offer a transparent wrapper to apply iptables rules to nftables. Without the config option for nftables the package isn't installed and therefore can't be tested. This commit enabled it and therefore provides the wrapper. The size of the iptables package increases from 25436 to 26500 Bytes. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: enable badblock table support on linksys ea7xxx devicesFelix Fietkau2022-01-132-0/+6
| | | | | | Use remapping only on the kernel partitions. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mtk_bmt: add support for the bbt format used on mt7621Felix Fietkau2022-01-131-6/+202
| | | | | | | | | This does not have spare blocks for remapping, and it is also not suitable for random write access. It only skips over bad blocks on linear writes of an image to a partition. As such, it is really only suitable for the kernel partition, or other partitions with mostly static data Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mtk_bmt: add abstraction for supporting other formatsFelix Fietkau2022-01-131-90/+122
| | | | | | Preparation for supporting remapping on MT7621 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621_nand: fix writing upper half of fdm dataFelix Fietkau2022-01-131-1/+1
| | | | | | | Since the loop iterates from 0-3, subtracting 4 from the shift multiplier does not make any sense Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: rework and fix mt7622-rfb1-ubi supportFelix Fietkau2022-01-134-12/+15
| | | | | | | | Limit bmt remapping range to cover everything up to and including the kernel image, use the rest of the flash area for ubi. Fix partition table and sysupgrade support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mtk_bmt: remap blocks after reaching bitflip thresholdFelix Fietkau2022-01-131-0/+4
| | | | | | This ensures that blocks are remapped before data becomes corrupt Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mtk_bmt: pass number of bitflips on read to the callerFelix Fietkau2022-01-131-2/+9
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mtk_bmt: add support for limiting range of remappingFelix Fietkau2022-01-131-7/+29
| | | | | | | | This can be used to support ubi on top of mtk_bmt without reflashing the boot loader. The boot loader + factory + kernel area is covered, while the rest is passed through as-is Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mtk_bmt: extend debug interfaceFelix Fietkau2022-01-131-0/+96
| | | | | | | Add support for showing remapped blocks and garbage collecting old remapped blocks triggered by using the mark_good/mark_bad files Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mtk_bmt: fix remapping after read/write failureFelix Fietkau2022-01-131-11/+67
| | | | | | Copy from the previous block in order to preserve existing data Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: move mediatek BMT support patch to generic patchesFelix Fietkau2022-01-136-871/+866
| | | | | | | Preparation for supporting BMT on MT7621. Move source files to the files/ subdirectory in order to simplify maintenance Signed-off-by: Felix Fietkau <nbd@nbd.name>
* generic: platform/mikrotik: use MTD notifierDenis Kalashnikov2022-01-134-28/+61
| | | | | | | | | | | | | | | | | | | | If the SPI probe is sufficiently delayed, the routerboot driver may fail to init as the routerboot partitions are not yet available. Register an MTD user notifier instead of doing straight init so that the init subroutines are only executed when the target MTD partitions are present. Because the init/exit routines can now be called outside of the kernel normal init/exit calls, they cannot be jettisoned and must always be available: the __init and __exit qualifiers are thus removed. Reported-by: Denis Kalashnikov <denis281089@gmail.com> Signed-off-by: Denis Kalashnikov <denis281089@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> [bump hardconfig/softconfig versions] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: qca955x: remove double declarationKoen Vandeputte2022-01-131-2/+1
| | | | | | No need to mention the same value twice Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: rb912: remove unused propertyKoen Vandeputte2022-01-131-1/+0
| | | | | | | ar934x does not define property 'rgmii-enabled' in the parsing code remove it Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: rb912: fix pll init issuesKoen Vandeputte2022-01-131-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds. Investigation shows that the board failed to adapt the ethernet pll values as shown here: [ 5.284359] ag71xx 19000000.eth: failed to read pll-handle property added custom prints in code and triggering a link switch: [ 62.821446] Atheros AG71xx: fast reset [ 62.826442] Atheros AG71xx: update pll 2 [ 62.830494] Atheros AG71xx: no pll regmap! Comparison with another very similar board (rb922 - QCA955x) showed a missing reference clock frequency in dts, which seems to cause a pll init issue. Unfortunately, no errors are printed when this occurs. Adding the frequency property fixes the pll init as it can be parsed now by the ethernet driver. [ 55.861407] Atheros AG71xx: fast reset [ 55.866403] Atheros AG71xx: update pll 2 [ 55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000 Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mikrotik: make soft_config writableOskari Lemmela2022-01-134-4/+0
| | | | | | Parent mtd partition needs to be writable Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mikrotik: enable variable size eraseOskari Lemmela2022-01-135-0/+401
| | | | | | | Add support for variable size erase blocks. Enable it to all targets which has mikrotik targets. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* generic: platform/mikrotik: make soft_config writable without 4K sectorsOskari Lemmela2022-01-131-15/+4
| | | | | | | | | Make soft_config writable in all cases. Performing soft_config commit will fail if mtd partition is not writable. Signed-off-by: Oskari Lemmela <oskari@lemmela.net> [bump rb_softconfig version number] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx: bump SDMA firmware to v3.6Koen Vandeputte2022-01-131-0/+0
| | | | | | No changelog available Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* netifd: update to git HEADHans Dedecker2022-01-121-3/+3
| | | | | | | | 96902e8 Revert "netifd: add devtype to ubus call" 29e6acf netifd: add devtype to ubus call 7ccbf08 netifd: add devtype to ubus call Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* procd: update to git HEADDaniel Golle2022-01-121-3/+3
| | | | | | | | | | ca6c35c uxc: usage message cosmetics e083dd4 uxc: fix two minor issues reported by Coverity 35dfbff procd: jail/cgroups: correctly enable "rdma" when requested 3b3ac64 procd: mount /dev with noexec ac2b8b3 procd: clean up /dev/pts mounts Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: deny write to uImage.FIT sub-image partitionsDaniel Golle2022-01-112-4/+8
| | | | | | | Set policy bit to force read-only mode on uImage.FIT filesystem sub-images mapped as block partitions by the FIT partition parser. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: Re-enable ARM arch timerDavid Woodhouse2022-01-101-0/+1
| | | | | | | | | CONFIG_ARM_ARCH_TIMER cannot be enabled in the config directly; it is only selected by CONFIG_HAVE_ARM_ARCH_TIMER. We need to enable the latter in our config. Signed-off-by: David Woodhouse <dwmw2@infradead.org> Fixes: 4f1c5b01c1 ("mediatek: mt7623: backport musb, improve HDMI console")
* mediatek: mt7623: Disable power button reset for U7623-02 boardDavid Woodhouse2022-01-101-0/+4
| | | | | | | | | | | | The Unielec U7623 doesn't have a physical power button; I think it's hard wired so that it turns on automatically when power is applied (unlike the Banana Pi R2 which is a pain). So the 'reset on long press of power button' behaviour that we get when we enable the PMIC keyboard driver is kind of unhelpful. Disable it. Signed-off-by: David Woodhouse <dwmw2@infradead.org> Fixes: 0d3f3323a2 ("mediatek: mt7623: enable more hardware features")
* firewall: update to latest HEADKevin Darbyshire-Bryant2022-01-101-3/+3
| | | | | | | | | 0f16ea5 options.c: add DSCP code LE Least Effort 24ba465 firewall3: remove redundant syn check df1306a firewall3: fix locking issue 3624c37 firewall3: support table load on access on Linux 5.15+ Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: Add support for OpenMesh OM5P-AC v1Sven Eckelmann2022-01-096-0/+237
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM5P-ANSven Eckelmann2022-01-096-2/+248
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 1T1R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + 10/100 Mbps Ethernet + builtin switch port 1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* opkg: update to git HEAD of 2022-01-09Daniel Golle2022-01-091-3/+3
| | | | | | | | | | db7fb64 libopkg: pkg_hash: prefer to-be-installed packages 2edcfad libopkg: set 'const' attribute for argv This should fix the ImageBuilder problems people are having since we introduced the 'uci-firewall' providers. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for ASUS RP-AC66Tamas Balogh2022-01-096-0/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC66 Repeater Hardware specifications: Board: AP152 SoC: QCA9563 DRAM: 64MB DDR2 Flash: 25l128 16MB SPI-NOR LAN/WAN: 1x1000M QCA8033 WiFi 5GHz: QCA9880 Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz MAC addresses as verified by OEM firmware: use address source Lan/Wan *:24 art 0x1002 (label) 2G *:24 art 0x1002 5G *:26 art 0x5006 Installation: Asus windows recovery tool: - install the Asus firmware restoration utility - unplug the router, hold the reset button while powering it on - release when the power LED flashes slowly - specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 - Start the Asus firmware restoration utility, specify the factory image and press upload - Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: - set computer to a static ip, 192.168.1.75 - connect computer to the LAN 1 port of the router - hold the reset button while powering on the router for a few seconds - send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* firewall4: bump to git HEADStijn Tintel2022-01-091-3/+3
| | | | | | | | | | | | 9a509d4 ruleset.uc: consolidate ip and ip6 offload 21f311d ruleset.uc: don't trim newline before comment sign f121383 tests: enable flow offloading in tests 550df40 tests: add test for unknown defaults option 47c5a5b tests: add test for deprecated rule option 69a89d6 tests: add test for unknown rule option 07579df fw4.uc: handle interface zone option Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mediatek mt7622: fix 300mhz typo in dtsFritz D. Ansel2022-01-091-0/+27
| | | | | | | | | | | | | | The lowest frequency should be 300MHz, since that is the label assigned to the OPP in the mt7622.dtsi device tree, while there is one missing zero in the actual value. To be clear, the lowest frequency should be 300MHz instead of 30MHz. As mentioned @dangowrt on the OpenWrt forum there is no benefit in leaving 30MHz as the lowest frequency. Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com> Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
* x86: improve sysinfo handling of dummy valuesStefan Lippers-Hollmann2022-01-081-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | Fall back to using board_vendor and board_name, if known dummy values are used for sys_vendor and product_name. Examples: To be filled by O.E.M.:To be filled by O.E.M. --> INTEL Corporation:ChiefRiver System manufacturer:System Product Name --> ASUSTeK COMPUTER INC.:P8H77-M PRO To Be Filled By O.E.M.:To Be Filled By O.E.M. --> ASRock:Q1900DC-ITX Gigabyte Technology Co., Ltd.:To be filled by O.E.M. --> Gigabyte Technology Co., Ltd.:H77M-D3H empty:empty --> TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211 To Be Filled By O.E.M.:To Be Filled By O.E.M. --> ASRock:H77 Pro4-M Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: janitorial work, respect line lengthsAlex Lewontin2022-01-081-19/+41
| | | | | | | This commit breaks up some lines so that they are shorter than 74 charcters. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* ipq806x: modularize generic subtargetAlex Lewontin2022-01-082-430/+431
| | | | | | | | This commit moves the device profiles within the ipq806x/generic subtarget into their own includable .mk file, to support eventually having subtargets other than generic. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* kernel: add kmod-usb-net-lan78xxJosef Schlehofer2022-01-081-0/+17
| | | | | | | | | | | | | | | | | Add kernel module for Microchip LAN78XX based USB 2 & USB 3 10/100/1000 Ethernet adapters. [1] This kernel module is required for the Seeed Studio's Mini Router based on RPI CM4 [2]. [1] <https://cateee.net/lkddb/web-lkddb/USB_LAN78XX.html> [2] <https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html> Link: <https://github.com/openwrt/openwrt/pull/4893> Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (added kmod-phy-microchip and kmod-fixed-phy dependencies, rpi3 needs lan78xx but has it built-in) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: provide kmod-fixed-phy as separate kmodChristian Lamparter2022-01-081-2/+17
| | | | | | | | | | Almost all targets have the fixed-phy feature built into the kernel. One big exception is x86. This caused a problem with the upcoming LAN78xx usb driver. Hence this patch breaks out the fixed-phy from of_mdio (which didn't include the .ko) and puts into a separate module. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: add kmod-phy-microchipChristian Lamparter2022-01-081-0/+15
| | | | | | | | phy drivers for Microchip's LAN88xx PHYs. This is needed for the "LAN7801" variant of the upstream lan78xx usb ethernet driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* toolchain/binutils: v2.37 Close the file descriptor if there is no archive fdHirokazu MORIKAWA2022-01-081-0/+184
| | | | | | | | | | | | | | | | | | | This fixes the following build error: /home/build/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-11.2.0_musl/lib/gcc/aarch64-openwrt-linux-musl/11.2.0/../../../../aarch64-openwrt-linux-musl/bin/ld: /home/sergey/openwrt2/build_dir/target-aarch64_cortex-a53_musl/node-v14.18.2/out/Release/obj.target/tools/v8_gypfiles/libv8_base_without_compiler.a: error adding symbols: malformed archive collect2: error: ld returned 1 exit status It's a bad error handling related to -EMFILE (too many open files). nodejs is probably just very close to open file limit. https://sourceware.org/bugzilla/show_bug.cgi?id=28138 https://github.com/nodejs/node/issues/39452 https://github.com/openwrt/packages/issues/17496 https://github.com/openwrt/packages/issues/16729 https://github.com/openwrt/packages/issues/17164 Signed-off-by: Hirokazu MORIKAWA <morikw2@gmail.com> [Take full patch from 2.37 branch and refresh] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: replace patches with version accepted upstreamAleksander Jan Bajkowski2022-01-085-15/+116
| | | | | | Replace recently added patches with version accepted upstream. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-19 10:56:25 +0000