aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mvebu: add Kobol Helios 4 deviceAlberto Bursi2020-07-179-0/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Helios 4 is a NAS from Kobol that is powered by an Armada 38x MicroSOM from Solidrun, similarly to Clearfog. This device has: -Armada 38x CPU (dual core ARMv7 1.6 Ghz) -2 GB of ECC RAM -Gigabit ethernet (Marvell) -2x USB 3.0 ports -4x Sata 3.0 ports -i2c header (J9 |>GND|SDA|SCL|VCC) -2x 3-pin fan headers with PWM -micro-usb port is a TTL/UART to USB converter connected to TTL -MicroSD card slot -System, 4xSata and 1xUSB LEDs NOT WORKING: fan control Fan Control requires a kernel patch that is available in the Armbian project (the "default firmware" of this device) and named mvebu-gpio-remove-hardcoded -timer-assignment This patch isn't acceptable by OpenWrt, it should be upstreamed. I also have that patch in my own local OpenWrt builds, in case you want a more clean and less confusing patch for upstreaming. To install, write the disk image on a micro SD card with dd or win32 disk imager, insert the card in the slot. Check that the dip switch battery for boot selection is as follows Switch 1 and 2 down/off, switches 3, 4, 5 up/on. Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
* uboot-mvebu: add uboot for helios 4Alberto Bursi2020-07-171-0/+8
| | | | | | add u-boot for Helios 4 NAS Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
* nat46: update to latest git HEADHans Dedecker2020-07-161-3/+3
| | | | | | ac712ad nat46-netdev: Add support for removing a rule Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: add support for D-Link DIR-867/DIR-882 A1Mateus B. Cassiano2020-07-166-152/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7300 v1Santiago Rodriguez-Papa2020-07-1610-159/+239
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600) * Flash: Macronix MX30LF1G18AC-TI (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Everything works! Been running it for a couple weeks now and haven't had any problems. Please let me know if you run into any. Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev> [use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: provide common definition for ELECOM WRC GS devicesAdrian Schmutzler2020-07-167-35/+24
| | | | | | | | | | | | | | Add a common definition for ELECOM WRC "GS" devices to mt7621.mk to not repeat the same assignments five times. To keep the naming consistent, slightly rename the DTSI and the factory image recipe as well. Note that elecom_wrc-1167ghbk2-s uses a slightly different build recipe for the factory image, so we keep it separate. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
* ramips: add support for ELECOM WRC-1750GS/GSVINAGAKI Hiroshi2020-07-163-0/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GS is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. WRC-1750GSV has the same hardware with WRC-1750GS. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-1750GS (or WRC-1750GSV) normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button for WRC-1750GS : wrc-1750gs-squashfs-factory.bin for WRC-1750GSV: wrc-1750gsv-squashfs-factory.bin 4. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: backport latest pci/e driver from upstreamJohn Crispin2020-07-167-24/+1932
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: generate UBI images for the rev boardJohn Crispin2020-07-163-2/+48
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: minor fix to eip97 driverJohn Crispin2020-07-161-2/+2
| | | | | | This patch makes the driver work on the newer v2.3 core. Signed-off-by: John Crispin <john@phrozen.org>
* ath79: harmonize model names for Ubiquiti devicesAdrian Schmutzler2020-07-1517-27/+26
| | | | | | | | | | | | | | | | | | | | This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: replace backticks in lib/upgrade/nand.shAdrian Schmutzler2020-07-151-4/+4
| | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* package: drop PKG_VERSION for purely local packagesAdrian Schmutzler2020-07-1515-22/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the package guidelines, PKG_VERSION is supposed to be used as "The upstream version number that we're downloading", while PKG_RELEASE is referred to as "The version of this package Makefile". Thus, the variables in a strict interpretation provide a clear distinction between "their" (upstream) version in PKG_VERSION and "our" (local OpenWrt trunk) version in PKG_RELEASE. For local (OpenWrt-only) packages, this implies that those will only need PKG_RELEASE defined, while PKG_VERSION does not apply following a strict interpretation. While the majority of "our" packages actually follow that scheme, there are also some that mix both variables or have one of them defined but keep them at "1". This is misleading and confusing, which can be observed by the fact that there typically either one of the variables is never bumped or the choice of the variable to increase depends on the person doing the change. Consequently, this patch aims at clarifying the situation by consistently using only PKG_RELEASE for "our" packages. To achieve that, PKG_VERSION is removed there, bumping PKG_RELEASE where necessary to ensure the resulting package version string is bigger than before. During adjustment, one has to make sure that the new resulting composite package version will not be considered "older" than the previous one. A useful tool for evaluating that is 'opkg compare-versions'. In principle, there are the following cases: 1. Sole PKG_VERSION replaced by sole PKG_RELEASE: In this case, the resulting version string does not change, it's just the value of the variable put in the file. Consequently, we do not bump the number in these cases so nobody is tempted to install the same package again. 2. PKG_VERSION and PKG_RELEASE replaced by sole PKG_RELEASE: In this case, the resulting version string has been "version-release", e.g. 1-3 or 1.0-3. For this case, the new PKG_RELEASE will just need to be higher than the previous PKG_VERSION. For the cases where PKG_VERSION has always sticked to "1", and PKG_RELEASE has been incremented, we take the most recent value of PKG_RELEASE. Apart from that, a few packages appear to have developed their own complex versioning scheme, e.g. using x.y.z number for PKG_VERSION _and_ a PKG_RELEASE (qos-scripts) or using dates for PKG_VERSION (adb-enablemodem, wwan). I didn't touch these few in this patch. Cc: Hans Dedecker <dedeckeh@gmail.com> Cc: Felix Fietkau <nbd@nbd.name> Cc: Andre Valentin <avalentin@marcant.net> Cc: Matthias Schiffer <mschiffer@universe-factory.net> Cc: Jo-Philipp Wich <jo@mein.io> Cc: Steven Barth <steven@midlink.org> Cc: Daniel Golle <dgolle@allnet.de> Cc: John Crispin <john@phrozen.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* vxlan: bump and change to PKG_RELEASEAdrian Schmutzler2020-07-151-1/+1
| | | | | | | | | | | | | Bumping package version has been overlooked in a previous commit. While at it, use PKG_RELEASE instead of PKG_VERSION, as the latter is meant for upstream version number only. (The effective version string for the package would be "3" in both cases, so there is no harm done for version comparison.) Fixes: 0453c3866feb ("vxlan: fix udp checksum control") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBridge MVieno Hakkerinen2020-07-155-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti PowerBridge M, which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - Internal antenna: 25 dBi - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other Bullet M (XM) boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbridge-m-squashfs-factory.bin Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
* ravpower-mcu: bump PKG_RELEASEDavid Bauer2020-07-151-1/+1
| | | | | | Fixes commit b94d1a2d2786 ("ravpower-mcu: remove target dependency") Signed-off-by: David Bauer <mail@david-bauer.net>
* vxlan: fix udp checksum controlJohannes Kimmel2020-07-151-0/+2
| | | | | | | | | | | So far, passing "rxcsum" and "txcsum" had no effect. Fixes: 95ab18e0124e ("vxlan: add options to enable and disable UDP checksums") Signed-off-by: Johannes Kimmel <fff@bareminimum.eu> [add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ravpower-mcu: remove target dependencyDavid Bauer2020-07-151-1/+0
| | | | | | | Remove the target dependency as the tool is also usable with other battery-powered routers. Signed-off-by: David Bauer <mail@david-bauer.net>
* iproute2: tc: fix missing em_ipset moduleTony Ambardar2020-07-142-1/+33
| | | | | | | | | | | | | Feature detection doesn't recognize ipset v7 use on kernel v5.x systems and thus disables the tc ematch function em_ipset. - backport patch: * 002-configure-support-ipset-v7.patch: 650591a7a70c configure: support ipset version 7 with kernel version 5 Fixes: 4e0c54bc5bc8 ("kernel: add support for kernel 5.4") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* iproute2: tc: fix dynamic symbol table size optimizationTony Ambardar2020-07-141-1/+1
| | | | | | | | | Recent iproute2 5.x versions modified the symbols resolved for plugins, causing "tc .. action xt .." to fail. Update the list of symbols to fix. Fixes: b61495409bb3 ("iproute2: tc: reduce size of dynamic symbol table") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix ethernet vlan double taggingJohn Crispin2020-07-142-11/+36
| | | | | | | | As the the SoC uses implicit vlan tagging for dual MAC support, the offload feature breaks when using double tagging. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: merge all ar40xx patches into one single patchJohn Crispin2020-07-142-30/+22
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: really fix aliases node for Qualcomm IPQ8064/DB149Adrian Schmutzler2020-07-142-2/+12
| | | | | | | | | | | | | | | Having looked at this again, it appears that only gsbi2_serial is actually enabled for this device, so the entry in the broken aliases node was correct. Therefore, this needs to set its own serial0 instead of inheriting "serial0 = &gsbi4_serial;" from DTSI. Do this with the correctly named aliases node now. Fixes: c83f7b6d217f ("ipq806x: fix aliases node name for Qualcomm IPQ8064/DB149") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: use consistent DT labels for gsbiX_serialAdrian Schmutzler2020-07-142-4/+4
| | | | | | | | | | Kernel uses the label gsbiX_serial, so let's adjust our labels to this naming scheme. This is cosmetic, and actually only already existing gsbi4_serial has been used at all. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: fix aliases node name for Qualcomm IPQ8064/DB149Adrian Schmutzler2020-07-142-11/+1
| | | | | | | | | | | | | | | | | | | | | | | This device uses a node incorrectly named "alias" instead of "aliases" since it was introduced. Remove it without replacement, as the definitions in it don't seem to be required anyway: The serial0 definition has never been effective anyway and this would be the only device deviating from the common setting "serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong node prevented us from finding out about the wrong serial definition?) The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48f6 anyway, the redundant definition in the alias node was just overlooked back then. Fixes: 0fd202f3e563 ("ipq806x: add db149 dts files") Fixes: d2a2eb7e48f6 ("ipq806x: replace caf nss-gmac driver by upstream stmmac") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* procd: allow optional watchdog instance parameterDaniel Bailey2020-07-141-2/+2
| | | | | | | | | | | | | | Optional instance watchdog timeout and watchdog mode can be set by adding: procd_set_param $mode $timeout $mode is an integer [0-1] representing instance watchdog mode of operation: 0 = disabled 1 = passive mode, client must periodically poke watchdog via ubus $timeout is an integer representing how often, in seconds, the watchdog must be poked. Signed-off-by: Daniel Bailey <danielb@meshplusplus.com>
* procd: update to git HEADDaniel Golle2020-07-141-3/+3
| | | | | | | 639df57 uxc: fix build with uClibc-ng b2230e4 procd: add service instance watchdog Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: use rgmii-id instead of rgmii in ubnt,lap-120Roger Pueyo Centelles2020-07-131-3/+2
| | | | | | | | | | | Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init) the incoming incoming traffic on the ubnt,lap-120 devices Ethernet port was not making it through. Using rgmii-id instead of rgmii (same configuration as ubnt,litebeam-ac-gen2) fixes it. Fixes FS#2893. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* build,json: fix compatibility with Python 3.5Paul Spooren2020-07-131-1/+1
| | | | | | | | The f-string feature was introduced in Python 3.6. As Buildbots may run on Debian 9, which comes per default with Python 3.5, this would cause an issue. Instead of f-strings use the *legacy* `.format()` function. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: add support for D-Link DIR-878 A1Mathieu Martin-Borret2020-07-133-1/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MT7621AT RAM: 128MB Flash: 16MB NOR SPI flash WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz) LAN: 5x1000M Firmware layout is Uboot with extra 96 bytes in header Base PCB is AP-MTKH7-0002 LEDs Power Green,Power Orange,Internet Green,Internet Orange LEDs "2.4G" Green & "5G" Green connected directly to wifi module Buttons Reset,WPS,WIFI Flashing instructions: Upload image via emergency recovery mode Push and hold reset button (on the back of the device) until power led starts flashing (about 10 secs or so) while powering the device on. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device. Some browsers/OS combinations are known not to work, so if you don't see the percentage complete displayed and moving within a few seconds, restart the procedure from scratch and try anoher one, or try the command line way. Alternative method using command line on Linux: curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1 Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com> [use of generic uimage-padhdr in image generation code] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: mtdsplit_uimage: add SGE parserMathieu Martin-Borret2020-07-131-0/+38
| | | | | | | Adding SGE parser for SGE (T&W) Shenzhen Gongjin Electronics to add 96 bytes padding the the firmware image Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
* glibc: fix avx2 strncmp offset compare condition check [BZ #25933]Hans Dedecker2020-07-131-2/+2
| | | | | | | 4e8a33a959 NEWS: Mention BZ 25933 fix fd15ba932d Fix avx2 strncmp offset compare condition check [BZ #25933 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* rockchip: don't disable timer LED triggerDavid Bauer2020-07-131-1/+0
| | | | | | | | The timer LED trigger is enabled in all targets (except for lantiq xway-legacy). It's necessary for the OpenWrt preinit LED pattern to work. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: use downstream GPIO button implementationDavid Bauer2020-07-132-2/+1
| | | | | | | | Use the OpenWrt netlink GPIO button implementation to forward button presses to procd. This is necessary to make failsafe-mode access using a button possible. Signed-off-by: David Bauer <mail@david-bauer.net>
* procd: update to git HEADDaniel Golle2020-07-131-3/+3
| | | | | | | | | | | | | | aed7fb3 procd: fix compilation with uClibc-ng 9d0f831 jail: fix segfault with len(uidmap/gidmap) > 1 42a6217 jail: consider PATH for argv in OCI container 83f4b72 jail: actually chdir into OCI defined CWD fc9f614 jail: parse and run OCI hooks 02eec92 jail: memory allocation fixes 71e75f4 jail: refactor mount support to cover OCI spec b586e7d jail: don't make mount source read-only dacab12 uxc: fix 'stop' command Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm47xx: disable image for Linksys WRT160n v3Adrian Schmutzler2020-07-131-0/+1
| | | | | | | | | | | | The device can only hold 3.6 MB, but newer images (since 18.06) are bigger, so flashing a new version fails. This disables default build for this device based on the bug report referenced below. Fixes: FS#1963 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate Netgear devices for mt7628Adrian Schmutzler2020-07-137-283/+151
| | | | | | | | | | | | | | | This creates a common DTSI and shared image definition for the relatively similar Netgear devices for mt7628 platform. As a side effect, this raises SPI flash frequency for the R6120, as it's expected to work there as well if it works for R6080 and R6020. Based on the data from the other devices, it also seems probable the 5g MAC address for R6120 could be extracted from the caldata, and the mtd-mac-address there could be dropped. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* wireguard: bump to 1.0.20200712Jason A. Donenfeld2020-07-131-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This release brings parity with the commits Linus released a few hours ago into 5.8-rc5. * receive: account for napi_gro_receive never returning GRO_DROP The napi_gro_receive function no longer returns GRO_DROP ever, making handling GRO_DROP dead code. This commit removes that dead code. Further, it's not even clear that device drivers have any business in taking action after passing off received packets; that's arguably out of their hands. * device: implement header_ops->parse_protocol for AF_PACKET WireGuard uses skb->protocol to determine packet type, and bails out if it's not set or set to something it's not expecting. For AF_PACKET injection, we need to support its call chain of: packet_sendmsg -> packet_snd -> packet_parse_headers -> dev_parse_header_protocol -> parse_protocol Without a valid parse_protocol, this returns zero, and wireguard then rejects the skb. So, this wires up the ip_tunnel handler for layer 3 packets for that case. * queueing: make use of ip_tunnel_parse_protocol Now that wg_examine_packet_protocol has been added for general consumption as ip_tunnel_parse_protocol, it's possible to remove wg_examine_packet_protocol and simply use the new ip_tunnel_parse_protocol function directly. * compat: backport ip_tunnel_parse_protocol and ip_tunnel_header_ops These are required for moving wg_examine_packet_protocol out of wireguard and into upstream. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* scripts/env: Fix 56f813674a scripts/env: use command -v instead of whichKevin Darbyshire-Bryant2020-07-121-1/+1
| | | | | | | | | | We don't need to see how git will be executed and it produces non silent output on 'scripts/env diff' commands when there are no differences unlike before. Re-introduce original silent behaviour. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: fix dsa binding for TP-Link TL-WR941ND v2Chuanhong Guo2020-07-122-13/+9
| | | | | | | | | upstream changed dt-bindings for marvell 88e6060 to use mdio-device and dropped support for legacy bindings. fix it in our local dts. Fixes: FS#2524 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qihoo,c301: use phy-supply for usb vbusChuanhong Guo2020-07-121-2/+2
| | | | | | | | Linux phy subsystem provides support for a phy regulator defined via phy-supply property. Use it to turn on usb power only when usb is probed. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mvebu: add support for MACCHIATObin Single ShotTomasz Maciej Nowak2020-07-124-7/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based Marvell ARMADA 8040 Community board. Single Shot was broken as the device tree is different on the Double Shot Board. Specifications: - Quad core Cortex-A72 (up to 2GHz) - DDR4 DIMM slot with optional ECC and single/dual chip select support - Dual 10GbE (1/2.5/10GbE) SFP+ 2.5GbE (1/2.5GbE) via SFP 1GbE via copper - SPI Flash - 3 X SATA 3.0 connectors - MicroSD connector - eMMC - PCI x4 3.0 slot - USB 2.0 Headers (Internal) - USB 3.0 connector - Console port (UART) over microUSB connector - 20-pin Connector for CPU JTAG debugger - 2 X UART Headers - 12V input via DC Jack - ATX type power connector - Form Factor: Mini-ITX (170 mm x 170 mm) More details at http://macchiatobin.net Installation: Write the Image to your Micro SD Card and insert it in the MACCHIATObin Single Shot SD Card Slot. In the U-Boot Environment: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually (hanging lines indicate wrapped one-line command): setenv fdt_name armada-8040-mcbin-singleshot.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv On newer Bootloaders (18.12) the Variables have been changed, use: setenv fdt_name armada-8040-mcbin-singleshot.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r $image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr_r - $fdt_addr_r' Reported-by: Alexandra Alth <alexandra@alth.de> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Tested-by: Alexandra Alth <alexandra@alth.de> [add specs and installation as provided by Alexandra Alth] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* scripts/mkits.sh: fix use of printfAdrian Schmutzler2020-07-111-2/+3
| | | | | | | | | | | Due to a line break, printf was accidentally called with three arguments instead of two, causing a different output than before. Fix it by splitting the printf command into two lines. Fixes: 907053193a1c ("scripts/mkits.sh: replace echo -e with printf") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate recipes with uimage_padhdrAdrian Schmutzler2020-07-113-13/+8
| | | | | | | | | | | There are already two very similar recipes using uimage_padhdr in ramips target, and a third one is about to be added. Make the recipe more generic, so redefinitions are not necessary anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
* mvebu: fix support for Marvell 8040 MACCHIATOBinAdrian Schmutzler2020-07-115-6/+20
| | | | | | | | | | | | | | | | | | | | | | Between kernels 4.20 and 5.0, a new variant of this board has been introduced ("Single Shot"), and the existing one has been renamed with the appendix "Double Shot". [1] This also adjusted the first compatible in the list: marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot This patch updates the OpenWrt implementation of this device by adjusting the relevant references to that compatible (i.e., our board name). To still provide support for 4.19 with our setup, this adds a small patch to change the compatible there as well. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52 Cc: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* bcm63xx: R5010UNv2: fix flash partitions for 16MB flashDaniel González Cabanelas2020-07-111-5/+5
| | | | | | | | | | | The router Nucom R5010UN v2 has the partitions defined for a 8MB flash, but the flash chip is 16MB size. We are wasting half of the flash. Fix it and use generic names for partitions. Fixes: 474cde61234c ("brcm63xx: probe SPI flash through DT") Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* build: improve ccache supportRoman Yeryomin2020-07-119-10/+29
| | | | | | | | | | | | | | | | | | Set CCACHE_DIR to $(TOPDIR)/.ccache and CCACHE_BASEDIR to $(TOPDIR). This allows to do clean and dirclean. Cache hit rate for test build after dirclean is ~65%. If CCACHE is enabled stats are printed out at the end of building process. CCACHE_DIR config variable allows to override default, which could be useful when sharing cache with many builds. cacheclean make target allows to clean the cache. Changes from v1: - remove ccache directory using CCACHE_DIR variable - remove ccache leftovers from sdk and toolchain make files - introduce CONFIG_CCACHE_DIR variable - introduce cacheclean make target Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ramips: mt7621: refactor set affinity scriptDENG Qingfang2020-07-111-19/+7
| | | | | | | | The current one only looks for mt76x2e and mt7603e, and does not work for 2 or more same Wi-Fi chips. Refactor the script to cover those cases. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ltq-vmmc: update permission handlingSebastian Kemper2020-07-112-13/+7
| | | | | | | | | | | | | | The firmware is currently just copied. It can end up with o= on the device (this is the case for voice_ar9_firmware.bin for instance). Instead of copying it the Makefile is changed to use the macro "$(INSTALL_DATA)" in order for the file to be world-readable. While at it refactor the device node creation in the init script with loop. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net> [removed 2nd part with custom group handling for device nodes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* layerscape: define IMAGE_SIZE and LS_SYSUPGRADE_IMAGE_SIZEYangbo Lu2020-07-113-10/+18
| | | | | | | | | Define 64m IMAGE_SIZE for flash firmware.bin since the flash size is 64MB. Define 48m LS_SYSUPGRADE_IMAGE_SIZE for flash sysupgrade.bin which contains maximum 16MB kernel and 32MB rootfs according to memory map. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-27 12:37:48 +0000