aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: move parser_trx patches of custom magic to genericINAGAKI Hiroshi2022-03-065-4/+5
| | | | | | | | This patch moves the patches of parser_trx in mediatek target to generic/backport-5.10 to use the changes from ramips target and backport the additional patch of the parser. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: update MAC address configuration for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-2/+2
| | | | | | | | This patch converts MAC address configuration of Buffalo WCR-1166DS in 02_network to use the generic function of OpenWrt. And also, add label_mac. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: increase spi frequency for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-1/+1
| | | | | | | Use higher frequency than current and up the speed to access to the flash on WCR-1166DS. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: Add support for TP-Link TL-WPA8631P v3Joe Mullally2022-03-064-0/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AV1300 Gigabit Passthrough Powerline ac Wi-Fi Extender Specifications -------------- * SoC: MediaTek MT7621AT * CPU: 880 MHz MIPS 1004KEc dual-core CPU * RAM: 64 MiB DDR2 (Zentel A3R12E40DBF-8E) * Flash: 8 MiB SPI NOR (GigaDevice GD25Q64CSIG) * Ethernet: SoC built-in Switch 5x 1GbE * Port 0: PLC (connected through AR8035-A) * Port 1-3: LAN * WLAN: 2x2 2.4GHz 300 Mbps + 2x2 5GHz 867 Mbps (MT7603EN + MT7613BEN) * PLC: HomePlug AV2 (Qualcomm QCA7500) * PLC Flash: 2MiB SPI NOR (GigaDevice GD25Q16CSIG) * Buttons: Reset, LED, Pair, Wi-Fi * LEDs: Power (green), PLC (green/amber), LAN (green), 2.4G (green), 5G (green) * UART: J1 (57600 baud) * Pinout: (3V3) (GND) (RX) (TX) * Visually identify GND from connection to PCB ground plane Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please first check the OpenWRT Wiki page for confirmation that your OEM firmware version is supported. Signed-off-by: Joe Mullally <jwmullally@gmail.com>
* iproute2: Remove libxtables from some tc variantsHauke Mehrtens2022-03-051-3/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds the new tc-bpf variant and removes libxtables dependency from the tc-tiny variant. The tc-full variant stays like before and contains everything. This allows to use tc without libxtables. The variants have the following sizes: root@OpenWrt:/# ls -al /usr/libexec/tc-* -rwxr-xr-x 1 root root 282453 Mar 1 21:55 /usr/libexec/tc-bpf -rwxr-xr-x 1 root root 282533 Mar 1 21:55 /usr/libexec/tc-full -rwxr-xr-x 1 root root 266037 Mar 1 21:55 /usr/libexec/tc-tiny They are linking the following shared libraries: root@OpenWrt:/# ldd /usr/libexec/tc-tiny /lib/ld-musl-mips-sf.so.1 (0x77d6e000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d4a000) libc.so => /lib/ld-musl-mips-sf.so.1 (0x77d6e000) root@OpenWrt:/# ldd /usr/libexec/tc-bpf /lib/ld-musl-mips-sf.so.1 (0x77da6000) libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77d60000) libelf.so.1 => /usr/lib/libelf.so.1 (0x77d3e000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d1a000) libc.so => /lib/ld-musl-mips-sf.so.1 (0x77da6000) libz.so.1 => /usr/lib/libz.so.1 (0x77cf6000) root@OpenWrt:/# ldd /usr/libexec/tc-full /lib/ld-musl-mips-sf.so.1 (0x77de8000) libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77da2000) libelf.so.1 => /usr/lib/libelf.so.1 (0x77d80000) libxtables.so.12 => /usr/lib/libxtables.so.12 (0x77d66000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d42000) libc.so => /lib/ld-musl-mips-sf.so.1 (0x77de8000) libz.so.1 => /usr/lib/libz.so.1 (0x77d1e000) This is based on a patch from Tiago Gaspar. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-envtools: mt7622: add support for Ruijie RG-EW3200GX PROLanghua Ye2022-03-051-0/+3
| | | | | | | | Add U-Boot environment settings for Ruijie RG-EW3200GX PRO to allow users to access the bootloader environment using fw_printenv/fw_setenv while running OpenWrt. Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* mediatek: add support for Ruijie RG-EW3200GX PROLanghua Ye2022-03-054-1/+370
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | X32 Pro is another product name for it in the Chinese market. Specifications: - SoC: MT7622B - RAM: 256MB - Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR - Ethernet: 5x1GbE - Switch: MT7531BE - WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN - 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) - 2Keys: Mesh button + Reset button - UART: Marked J19 on board. 3.3v, 115200n1 - Power: 12V 2.5A MAC addresses as verified by OEM firmware: use address source WAN *:F4 ethaddr@product_info LAN *:F5 5g *:F6 2g *:F7 Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* kernel: add support for XMC XM25QH128CLanghua Ye2022-03-051-0/+11
| | | | | | | The XMC XM25QH128C is a 16MB SPI NOR chip. The patch is verified on Ruijie RG-EW3200GX PRO. Datasheet available at https://www.xmcwh.com/uploads/435/XM25QH128C.pdf Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* libnetfilter-conntrack: backport patch fixing compilation with 5.15Ansuel Smith2022-03-052-1/+50
| | | | | | Backport patch fixing compilation with 5.15 and musl provided by Robert Marko Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: bump 5.10 to 5.10.103Rui Salvaterra2022-03-05154-1537/+525
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* util-linux: add lsnsOskari Rauta2022-03-051-0/+16
| | | | | | lsns lists system namespaces Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
* uboot-mvebu: backport patch to fix nvme detail crashJosef Schlehofer2022-03-051-0/+92
| | | | | | | | | | | | | | | | | | | | | Steps to reproduce: 1. Insert NVMe disk with a reduction to Turris Omnia 2. Go to U-boot 3. Run these two commands: a) ``nvme scan`` b) ``nvme detail`` 4. Wait for crash This is backported from U-boot upstream repository. It should be included in the upcoming release - 2022.04 [1]. It was tested on Turris Omnia, mvebu, cortex-a9, OpenWrt master. [1] https://patchwork.ozlabs.org/project/uboot/patch/20211209100639.21530-1-pali@kernel.org/ Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Export the patch from U-Boot git] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mkhash: fix build errors on FreeBSD 13.0Georgi Valkov2022-03-051-1/+1
| | | | | | | | | | | | | | be64enc, be16dec, and be32dec are declared on FreeBSD 13.0, in /usr/include/sys/endian.h so we should not declare them. Fixes the following error during feeds update: staging_dir/host/bin/mkhash: No such file or directory gcc scripts/mkhash.c scripts/mkhash.c:111:1: error: redefinition of 'be64enc' 111 | be64enc(void *buf, uint64_t u) Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
* tools/fakeroot: restore macos bugfix that was dropped during the last updateFelix Fietkau2022-03-051-0/+43
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* qosify: bump to git HEADStijn Tintel2022-03-042-4/+4
| | | | | | | | interface: disable autorate-ingress by default Also change the example config to reflect this. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qosify: add PKG_RELEASEStijn Tintel2022-03-041-0/+1
| | | | | | | | | Without PKG_RELEASE, it's impossible to trigger package updates when changing files included in the package that are not in the qosify git repository. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Felix Fietkau <nbd@nbd.name>
* bcm4908: support "rootfs_data" on U-Boot devicesRafał Miłecki2022-03-043-13/+122
| | | | | | | | | | | | | | | | | | | | | | | | | 1. Create "rootfs_data" dynamicaly U-Boot firmware images can contain only 2 UBI volumes: bootfs (container with U-Boot + kernel + DTBs) and rootfs (e.g. squashfs). There is no way to include "rootfs_data" UBI volume or make firmware file tell U-Boot to create one. For that reason "rootfs_data" needs to be created dynamically. Use preinit script to handle that. Fire it right before "mount_root" one. 2. Relate "rootfs_data" to flashed firmware As already explained flashing new firmware with U-Boot will do nothing to the "rootfs_data". It could result in new firmware reusing old "rootfs_data" overlay UBI volume and its file. Users expect a clean state after flashing firmware (even if flashing the same one). Solve that by reading flash counter of running firmware and storing it in "rootfs_data" UBI volume. Every mismatch will result in wiping old data. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* procd: remove support for mounting /tmp in zramRui Salvaterra2022-03-031-10/+1
| | | | | | | | | | | | | | | | | The /tmp directory is mounted as tmpfs. The tmpfs filesystem is backed by anonymous memory, which means it can be swapped out at any time, if there is memory pressure [1]. For this reason, a zram swap device is a much better choice than mounting /tmp on zram, since it's able to compress all anonymous memory, and not just the memory assigned to /tmp. We already have the zram-swap package for this specific purpose, which means procd's tmp-on-zram is both redundant and more limited. A follow-up patch will remove support for mounting /tmp in zram from procd itself. [1] https://www.kernel.org/doc/Documentation/filesystems/tmpfs.txt Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: 5.10: remove CONFIG_DEVTMPFS{,_MOUNT} from kconfigsRui Salvaterra2022-03-016-11/+0
| | | | | | They are required for container support, but are handled in Config-kernel.in. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: 5.10: allocate last level PTEs in high memoryRui Salvaterra2022-03-017-7/+7
| | | | | | | | | | Enable support for allocating user space page table entries in high memory [1], for the targets which support this feature. This saves precious low memory (permanently mapped, the only type of memory directly accessible by the kernel). [1] https://www.kernel.org/doc/html/latest/vm/highmem.html Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.102John Audia2022-03-0119-92/+52
| | | | | | | | | | | | | | | Removed upstreamed: bcm4908/patches-5.10/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.102&id=f333c1916fd6b55900029bf8f918cc00009e2111 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.101John Audia2022-03-0141-188/+89
| | | | | | | | | | | | | | | | | Removed upstreamed: pending-5.10/841-USB-serial-option-add-ZTE-MF286D-modem.patch[1] bcm27xx/950-0592-drm-vc4-Allow-DBLCLK-modes-even-if-horz-timing-is-od.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.101&id=7113440a36c741efd7c76e3d70b3634100120cdb 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.101&id=21c890ca8eaecea06cabb92be2a53a6f26f56383 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: kmod-tcp-scalable: add scalable tcp congestion algorithmCatalin Toda2022-03-011-0/+18
| | | | Signed-off-by: Catalin Toda <catalinii@gmail.com>
* ipset: update to 7.15Florian Eckert2022-03-012-2/+14
| | | | | | | | | Update to the latest upstream version. In this version there is a new tool with which you can convert ipsets into nftables sets. Since we are now using nftables as default firewall, this could be a useful tool for porting ipsets to nftables sets. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* tools/libressl: update to version 3.4.2Josef Schlehofer2022-03-011-2/+2
| | | | | | | | | | | | | | | Release notes: https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.4.2-relnotes.txt ``` It includes the following security fix * In some situations the X.509 verifier would discard an error on an unverified certificate chain, resulting in an authentication bypass. Thanks to Ilya Shipitsin and Timo Steinlein for reporting. ``` Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* tools/mkimage: update to 2022.01Huangbin Zhan2022-03-013-17/+30
| | | | | | | | | | | | - enable dot config - enable openwrt verbose - add bison as dependency to avoid failure ``` bison -oscripts/kconfig/zconf.tab.c -t -l scripts/kconfig/zconf.y bison: /builder/shared-workdir/build/staging_dir/host/share/bison/m4sugar/m4sugar.m4: cannot open: No such file or directory ``` Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
* tools/fakeroot: update to 1.27Rosen Penev2022-03-015-134/+17
| | | | | | | | | | Remove macOS stuff. Upstream has fixed it in the same way. Add SOL_TCP define. Taken from elsewhere in the code. Refreshed patches. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/expat: update to 2.4.6Rosen Penev2022-03-012-11/+16
| | | | | | | | | | | Switched to CMake for faster compilation and greater parallel friendliness. Added CMake options from the packages feed. This release fixes various CVEs. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/findutils: update to 4.9.0Rosen Penev2022-03-012-2/+22
| | | | | | | | Add compilation fix for Ubuntu 20.04. Provided by upstream maintainer: https://github.com/openwrt/packages/issues/17912#issuecomment-1046726426 Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/zstd: update to 1.5.2Rosen Penev2022-03-012-11/+21
| | | | | | | Switched to building with meson as it's faster and does not need a dependency on cmake, which takes a long time to build. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/ccache: add cmake dependencyRosen Penev2022-03-011-1/+1
| | | | | | | This will be needed for the next commit as ccache's cmake dependency is satisfied by zstd currenly. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/cmake: update to 3.22.2Rosen Penev2022-03-011-2/+2
| | | | | | Mostly random Python 3.10 fixes. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/mtools: update to 4.0.37Rosen Penev2022-03-011-2/+2
| | | | | | No changelog is available. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/mklibs: update to 0.1.45Rosen Penev2022-03-0110-287/+37
| | | | | | | | | | | | | Refresh 2to3 patch. Upstream partially did this against some older python version. This is still needed. Refreshed other patches to be python3 safe. Remove uClibc patches as only musl is present now. Refresh others. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* layerscape: use semantic versions for LSDKPaul Spooren2022-03-019-9/+9
| | | | | | PKG_VERSION should not contain the package name but the version only. Signed-off-by: Paul Spooren <mail@aparcar.org>
* u-boot.mk: add LOCALVERSION (explicitly specify OpenWrt build)Josef Schlehofer2022-02-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For debugging purposes, we need to know if users are using modified U-boot versions or not. Currently, the U-boot version is somehow stripped. This is a little bit problematic when there are backported/wip/to-upstream patches. To make it more confusing, there was (before this commit) two U-boot versioning. U-boot compiled by OpenWrt build bots are missing ``Build:`` This is also the case when the U-boot is compiled locally. Example: ``` U-Boot SPL 2022.01 (Jan 27 2022 - 00:24:34 +0000) U-Boot 2022.01 (Jan 27 2022 - 00:24:34 +0000) ``` On the other hand, if you run full build, you can at least see, where it was compiled. Notice added ``Build:``. Example: ``` U-Boot 2022.01 (Jan 27 2022 - 00:24:34 +0000), Build: jenkins-turris-os-packages-burstlab-omnia-216 ``` In both cases, it is not clear to U-boot developers if it is an unmodified build. This is also caused that there is a missing ``.git`` file from U-boot folder, and so there is no history. It leads to that it can not contain suffix ``-dirty`` (uncommitted modifications) or even something else like number of commits, etc. [1] When U-boot is compiled as it should be, the version should look like this: ``U-Boot 2022.04-rc1-01173-g278195ea1f (Feb 11 2022 - 14:46:50 +0100)`` The date is not changed daily when there are new OpenWrt builds. This commit adds OpenWrt specific version, which could be verified by using strings. ``` $ strings bin/targets/mvebu/cortexa9/u-boot-omnia/u-boot-spl.kwb | grep -E "OpenWrt*" U-Boot SPL 2022.01-OpenWrt-r18942+54-cbfce92367 (Feb 21 2022 - 13:17:34 +0000) arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r18942+54-cbfce92367) 11.2.0 2022.01-OpenWrt-r18942+54-cbfce92367 U-Boot 2022.01-OpenWrt-r18942+54-cbfce92367 (Feb 21 2022 - 13:17:34 +0000) ``` [1] https://u-boot.readthedocs.io/en/latest/develop/version.html Reported-by: Pali Rohár <pali@kernel.org> Suggested-by: Karel Kočí <karel.koci@nic.cz> Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* image-commands.mk: Use ERROR_MESSAGE for imagesize failsPaul Spooren2022-02-281-1/+1
| | | | | | | | | | | | | If a image is bigger than the device can handle, an error message is printed. This is usually silenced and silently ignored, making it harder to debug. While it's possible to run the build in verbose mode (via `make V=s`) and grep for *is too big*, it's more intuitive to print the error message directly. For that use the newly unlocked `$(call ERROR_MESSAGE,...)` definition which now also print in non-verbose mode. Fixes: FS#50 (aka #7604) Signed-off-by: Paul Spooren <mail@aparcar.org>
* verbose.mk: print ERROR messages in non-verbosePaul Spooren2022-02-281-5/+4
| | | | | | | | | | | | | | | | | | | Using `make -j9` only prints a subset of messages to follow the build process progressing. However this silently skips over errors which might be of interested. Using `make V=s` easily floods the terminal making it hard to find error messages between the lines. A compromise is the usage of `$(call ERROR_MESSAGE,...)` which prints a message in red. This function is silenced in the non-verbose mode, even if only used at a single place in `package/Makefile` where it notifies about a OPKG corner case. This commit moves the `ERROR_MESSAGE` definition outside of the `OPENWRT_VERBOSE` condition and print error messages in every mode. With this in place further error messages are possible. Signed-off-by: Paul Spooren <mail@aparcar.org>
* bcm27xx: bcm2710: update defconfigJohn Audia2022-02-281-2/+0
| | | | | | | | | | | | Ran `make kernel_menuconfig CONFIG_TARGET=bcm2710` having used the snapshot config for bcm2710[1]. Manually added back two symbols that the make target removed, namely: * # CONFIG_SND_SOC_AD193X_I2C is not set * # CONFIG_SND_SOC_AD193X_SPI is not set 1. https://downloads.openwrt.org/snapshots/targets/bcm27xx/bcm2710/config.buildinfo Signed-off-by: John Audia <graysky@archlinux.us>
* bcm27xx: bcm2711: update defconfigJohn Audia2022-02-281-2/+0
| | | | | | | | | | | | | | | | | | Ran `make kernel_menuconfig CONFIG_TARGET=bcm2711` having used the snapshot config for bcm2711[1]. Manually added back two symbols that the make target removed, namely: * # CONFIG_SND_SOC_AD193X_I2C is not set * # CONFIG_SND_SOC_AD193X_SPI is not set Without adding these back, the build fails due to unsatisfied deps[2]. Build system: x86_64 Build-tested: bcm2711/multidevices 1. https://downloads.openwrt.org/snapshots/targets/bcm27xx/bcm2711/config.buildinfo 2. https://github.com/openwrt/openwrt/commit/a478202d74b66c3da17d57442649eb4f131fc7b2#commitcomment-67096592 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: move CONFIG_ASN1 to generic configJohn Audia2022-02-281-0/+1
| | | | | | | Rather than populating this symbol in the individual configs, move it to the generic config. Signed-off-by: John Audia <graysky@archlinux.us>
* iptables: bump PKG_RELEASEEtienne Champetier2022-02-281-1/+1
| | | | | | Following dependencies rework, bump PKG_RELEASE Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
* iptables: move libiptext* to their own packagesEtienne Champetier2022-02-282-20/+46
| | | | | | | | iptables-nft doesn't depend on libip{4,6}tc, so move libiptext* libs in their own packages to clean up dependencies Rename libxtables-nft to libiptext-nft Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
* iptables: rename to ip(6)tables-legacy, add PROVIDESEtienne Champetier2022-02-281-8/+12
| | | | | | | | Using PROVIDES allows to have other packages continue to depend on iptables and users to pick between legacy and nft version. Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
* iptables: move IPTABLES_{CONNLABEL,NFTABLES} to libxtablesEtienne Champetier2022-02-281-15/+15
| | | | | | Those 2 configs are not specific to iptables(-legacy) Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
* iptables: make mod depend on libxtablesEtienne Champetier2022-02-281-4/+3
| | | | | | | | | 'iptables-mod-' can be used directly by firewall3, by iptables and by iptables-nft. They are not linked to iptables but to libxtables, so fix the dependencies to allow to remove iptables(-legacy) Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
* iptables: fix libnftnl/IPTABLES_NFTABLES dependencyEtienne Champetier2022-02-281-5/+3
| | | | | | | | | libxtables doesn't depend on libnftnl, iptables-nft does, so move the dependency to not pull libnftnl with firewall3/iptables-legacy Also libxtables-nft depends on IPTABLES_NFTABLES Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
* mt7620: fix missing kernel config symbolPetr Štetiar2022-02-281-0/+1
| | | | | | | | | | | Fixes following missing kernel config symbol after adding GPIO watchdog: Software watchdog (SOFT_WATCHDOG) [M/n/y/?] m Watchdog device controlled through GPIO-line (GPIO_WATCHDOG) [Y/n/m/?] y Register the watchdog as early as possible (GPIO_WATCHDOG_ARCH_INITCALL) [N/y/?] (NEW) Fixes: 1a97c03d864e ("rampis: feed zbt-we1026 external watchdog") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ubus: bump to git HEADStijn Tintel2022-02-281-3/+3
| | | | | | | | 66baa44 libubus: introduce new status messages b3cd5ab cli: use UBUS_STATUS_PARSE_ERROR 584f56a cli: improve error logging for call command Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq806x: base-files: asrock: fix bootcount includePetr Štetiar2022-02-281-1/+1
| | | | | | | | | | | | | | | Fixes following warning message during image building process: Finalizing root filesystem... root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory Enabling boot root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory Enabling bootcount Fixes #9350 Fixes: 98b86296e67d ("ipq806x: add support for ASRock G10") Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 03:30:41 +0000