aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for MikroTik RouterBOARD 493G (rb4xx series)Christopher Hill2020-06-157-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD RB493G, ported from the ar71xx target. See https://routerboard.com/RB493G for details Specification: - SoC Qualcomm Atheros AR7161 - RAM: 256 MiB - Storage: 128MiB NAND - Ethernet: 9x 1000/100/10 Mbps - USB 1x 2.0 / 1.0 type A - PCIe: 3x Mini slot - MicroSD slot Working: - Board/system detection - Ethernet - SPI - NAND - LEDs - USB - Sysupgrade Enabled (but untested due to lack of hardware): - PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed Installation methods: - tftp boot initramfs image, scp then flash via "sysupgrade -n" - nand boot existing OpenWrt, scp then flash via "sysupgrade -n" Notes: - initramfs image will not work if uncompressed image size over ~8.5Mb - The "rb4xx" drivers have been enabled Signed-off-by: Christopher Hill <ch6574@gmail.com>
* ath79: add Mikrotik rb4xx series driversChristopher Hill2020-06-156-0/+817
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds 3 Mikrotik rb4xx series drivers as follows: rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device that interfaces between the SoC SPI bus and its two children below. rb4xx-gpio: This is the GPIO expander. rb4xx-nand: This is the NAND driver. The history of this code comes in three phases. 1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/. Module-author: Gabor Juhos <juhosg@openwrt.org> Module-author: Imre Kaloz <kaloz@openwrt.org> Module-author: Bert Vermeulen <bert@biot.com> 2. Next several ar71xx patches were applied bringing the code current. commit 7bbf4117c6fe4b764d9d7c62fb2bcf6dd93bff2c Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> commit af79fdbe4af32a287798b579141204bda056b8aa commit 889272d92db689fd9c910243635e44c9d8323095 commit e21cb649a235180563363b8af5ba8296b9ac0baa commit 7c09fa4a7492ca436f2c94bd9a465b7c5bbeed6f Signed-off-by: Felix Fietkau <nbd@nbd.name> 3. Finally a heavy refactor to split the driver into the three new subsystems, and updated to work with the device tree configuration, plus updates and review feedback incorporated Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Christopher Hill <ch6574@gmail.com>
* ath79: patch upstream Mikrotik rb4xx-spi driver to be device tree awareChristopher Hill2020-06-154-0/+224
| | | | | | | Backport upstream patches that make drivers/spi/spi-rb4xx.c device tree aware, plus a null pointer fix. Signed-off-by: Christopher Hill <ch6574@gmail.com>
* bcm63xx: a226m-fwb: fix linux partition offsetDaniel González Cabanelas2020-06-151-4/+4
| | | | | | | | | | | | | | | | | | The Pirelli A226M-FWB has a wrong linux partition offset, caused by a copy-paste error. As of result of this, OpenWrt is currently broken in this unit. Fix it. While at it, also use generic node names and fix the addresses there as well. Fixes: a27d59bb4274 ("brcm63xx: switch to new partition layout specification") Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> [also fix/update node names, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: ag71xx: don't warn on RGMII_RXID and RGMII_TXIDDavid Bauer2020-06-151-0/+4
| | | | | | | | | | Currently, ag71xx will trigger a warning when TX xor RX-Delay modes are enabled. Handle them identical to the already implemented RGMII modes, as they are only different for the attached PHY. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix IPv4-only corner case in 01_enable_packet_steeringAdrian Schmutzler2020-06-151-0/+1
| | | | | | | | | | | | | | | | The uci config section network.globals set up in /bin/config_generate will only be created if /proc/sys/net/ipv6 exists. Correspondingly, lacking IPv6 support, the command uci set network.globals.packet_steering=1 will fail with "uci: Invalid argument" as the network.globals config has not been set up. Fix that by adding the setup there as well. Fixes: dfd62e575c6c ("ramips: enable packet steering by default on mt7621") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "kirkwood: disable image for Linksys EA3500 (Audi)"Pawel Dembicki2020-06-141-1/+0
| | | | | | | | | | This reverts commit d9ff49967145600ff4bbc0f4eecef11fd96f6b16. At this moment kernel can be fitted in EA3500 image. Tested by onefreeman (OpenWrt forum user) Tested-by: Jacks <jack338c@gmail.com> (Github user @jack338c) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: refresh kernel configPawel Dembicki2020-06-141-9/+4
| | | | | | | | It was made by running "make kernel_oldconfig". Suggested-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: move ext4 support to modulesPawel Dembicki2020-06-142-11/+9
| | | | | | | | | | | | Ext4 support is built in kirkwood kernel. This patch moves ext4 support to modules and enables it for devices with SATA interface. Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [rebase] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: move usb support to modulesPawel Dembicki2020-06-145-6/+4
| | | | | | | | | | | | | | | USB support built in kernel isn't required for booting. This patch move USB support to modules. CONFIG_USB_STORAGE is removed because it can be found in kmod-usb-storage and all usb support for this targed is moved to kmods. Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310] Tested-by: Alberto Bursi <bobafetthotmail@gmail.com> [nsa325, ea4500] Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [keep CONFIG_SCSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: move mmc/sd features to modulesPawel Dembicki2020-06-143-4/+19
| | | | | | | | | | All devices are using nand images. Built-in MMC/SD modules are not needed anymore. Run tested: pogo v4 Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: move sata features to modulesPawel Dembicki2020-06-145-5/+13
| | | | | | | | | | All devices are using nand images. Built-in SATA modules are not needed anymore. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [only move CONFIG_SATA_MV] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [pogo v4]
* kirkwood: move led triggers to dtsPawel Dembicki2020-06-143-11/+27
| | | | | | | | | This patch moves led trigger settings from 01_leds file to dts. Now "linux,default-trigger" property is used. Tested-by: Alberto Bursi <bobafetthotmail@gmail.com> [nsa310,nsa325] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: check kernel-size for NBG6617David Bauer2020-06-141-0/+1
| | | | | | | | | The ZyXEL NBG6617 has a separate kernel partition which is 4MiB large. Add the kernel size to validate the kernel won't be bigger than this fixed limit. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add image size checks for several devicesDavid Bauer2020-06-141-3/+6
| | | | | | | This adds image size checks for various devies using an automatic mtdsplit. Signed-off-by: David Bauer <mail@david-bauer.net>
* musl: use official release tarAlexander Couzens2020-06-141-6/+3
| | | | | | | | | | | To prevent "wrong" musl packages which have a new version number but the package still contains an old version, because PKG_SOURCE_VERSION was unchanged. Ref: musl ml https://www.openwall.com/lists/musl/2020/05/22/4 Reviewed-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* iproute2: update to 5.7.0Hans Dedecker2020-06-132-2/+48
| | | | | | Update iproute2 to latest stable 5.7.0; for the changes see https://lwn.net/Articles/822152/ Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* hostapd: hostapd_set_psk_file: fix defaut value for macJohann Neuhauser2020-06-131-1/+1
| | | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Bringing up of station vlan fails if the optional mac entry isn't set. The default mac "00:00:00:00:00:00", which should match all stations, is mistakenly set to the non used variable "isolate". This results in a wrong formatted .psk file which has to be "vlan_id mac key". fixes: 5aa2ddd0: hostapd: add support for wifi-station and wifi-vlan sections Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ipq40xx: use zImage for EX6100v2 and EX6150v2David Bauer2020-06-131-3/+1
| | | | | | | | | | | | | | The NETGEAR EX61500v2 and EX6150v2 U-Boot does not support booting LZMA compressed images. Currently, they are using GZIP compressed kernels, which results in ledd flash being available to the root and overlay filesystems. Using a zImage results in a smaller kernel and therefore increases available space for rootfs and overlayfs. Size reduced: ~1.1 MiB Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: disable DSA and SwitchdevDENG Qingfang2020-06-132-11/+0
| | | | | | | | | | ipq40xx is still using swconfig based switch management. This might change in he future, however disable the DSA and Switchdev support for now. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [rephrased commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for EnGenius EMR3500Yen-Ting-Shen2020-06-137-1/+267
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (2 ports) USB: 1 x 2.0 (Host controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMR3500. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [squashed update patch, updated to 5.4, dropped BOARD_NAME, migrated to SOC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: essedma: Disable TCP segmentation offload for IPv6Sven Eckelmann2020-06-131-7/+4
| | | | | | | | | | | | | | | | | | | | | It was noticed that the the whole MAC can hang when transferring data from one ar40xx port (WAN ports) to the CPU and from the CPU back to another ar40xx port (LAN ports). The CPU was doing only NATing in that process. Usually, the problem first starts with a simple data corruption: $ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null ... Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected. ... Read error at byte 48807936/352321536 (Decryption has failed.). Retrying. But after a short while, the whole MAC will stop to react. No traffic can be transported anymore from the CPU port from/to the AR40xx PHY/switch and the MAC has to be resetted. Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: John Crispin <john@phrozen.org>
* ramips: drop useless label-mac-device for RouterBOARD 750Gr3Adrian Schmutzler2020-06-131-1/+0
| | | | | | | | | | | | | | With the new driver, MAC addresses are not set up in DTS anymore, and therefore label-mac-device will be useless there. Setup is done properly in 02_network, so this just removes the obsolete alias. Fixes: 5e50515fa6b3 ("ramips/mt7621: mikrotik: don't use mtd-mac-address in DTS") Suggested-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm47xx: move device definitions to subfilesAdrian Schmutzler2020-06-124-852/+848
| | | | | | | | | With several subtargets, the image/Makefile becomes crowded after a while. Many targets have moved their device definitions to $subtarget.mk files to have them more organized, let's do this here as well. Cc: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix port display for TRENDnet TEW-810DRJ. Scott Heppler2020-06-121-1/+1
| | | | | | | | | | This updates the display port order for the TEW-810DR to be in line with the DIR-810L. Both share the same board and pictures on the vendors' pages indicate the same external numbering scheme as well. Signed-off-by: J. Scott Heppler <shep971@centurylink.net> [replace commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: add support for NETGEAR WAC104Pawel Dembicki2020-06-124-1/+186
| | | | | | | | | | | | | | | | | | | | | | | | NETGEAR WAC104 is an AP based on castrated R6220, without WAN port and USB. SoC: MediaTek MT7621ST RAM: 128M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7612EN an+ac MediaTek MT7603EN bgn ETH: MediaTek MT7621ST (4x LAN) BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: 7x (3x GPIO controlled) Installation: Login to netgear webinterface and flash factory.img Back to stock: Use nmrpflash to revert stock image. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ath79: add support for D-Link DAP-2695-A1Stijn Tintel2020-06-117-0/+235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: * SoC: Qualcomm Atheros QCA9558 * RAM: 256MB * Flash: 16MB SPI NOR * Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD) * WiFi 2.4GHz: Qualcomm Atheros QCA9558 * WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E * LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER * Buttons: 1x RESET * UART: 1x RJ45 RS-232 Console port Installation via stock firmware: * Install the factory image via the stock firmware web interface Installation via bootloader Emergency Web Server: * Connect your PC to the LAN1(PoE) port * Configure your PC with IP address 192.168.0.90 * Open a serial console to the Console port (115200,8n1) * Press "q" within 2s when "press 'q' to stop autoboot" appears * Open http://192.168.0.50 in a browser * Upload either the factory or the sysupgrade image * Once you see "write image into flash...OK,dest addr=0x9f070000" you can power-cycle the device. Ignore "checksum bad" messages. Setting the MAC addresses for the ethernet interfaces via /etc/board.d/02_network adds the following snippets to /etc/config/network: config device 'lan_eth0_1_dev' option name 'eth0.1' option macaddr 'xx:xx:xx:xx:xx:xx' config device 'wan_eth1_2_dev' option name 'eth1.2' option macaddr 'xx:xx:xx:xx:xx:xx' This would result in the proper MAC addresses being set for the VLAN subinterfaces, but the parent interfaces would still have a random MAC address. Using untagged VLANs could solve this, but would still leave those extra snippets in /etc/config/network, and then the device VLAN setup would differ from the one used in ar71xx. Therefore, the MAC addresses of the ethernet interfaces are being set via preinit instead. The bdcfg partition contains 4 MAC address labels: - lanmac - wanmac - wlanmac - wlanmac_a The first 3 all contain the same MAC address, which is also the one on the label. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: enable wrgg MTD splitterStijn Tintel2020-06-112-0/+2
| | | | | | This is required for the D-Link DAP-2695-A1. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mtd: enable wrgg support for ath79Stijn Tintel2020-06-111-1/+1
| | | | | | This is required for the D-Link DAP-2695-A1. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* odhcpd: remove bogus IPKG_INSTROOT referenceKevin Darbyshire-Bryant2020-06-112-2/+2
| | | | | | | | | IPKG_INSTROOT is only set under image builder and we won't be running this script at build time either, so remove the reference before it gets cargo-culted into other scripts. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: rtl8367b: fix external interface modesINAGAKI Hiroshi2020-06-112-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The interface mode number of RGMII_33V is 7 on RTL8367, but it's 9 on RTL8367B. the external interface modes for RTL8367 are follows: - 0, Disabled - 1, RGMII - 2, MII_MAC - 3, MII_PHY - 4, TMII_MAC - 5, TMII_PHY - 6, GMII - 7, RGMII_33V the external interface modes for RTL8367B are follows: - 0, Disabled - 1, RGMII - 2, MII_MAC - 3, MII_PHY - 4, TMII_MAC - 5, TMII_PHY - 6, GMII - 7, RMII_MAC - 8, RMII_PHY - 9, RGMII_33V But the driver in U-Boot of RT-N56U GPL tar blocks using RGMII_33V (9) mode and it seems to be unsupported on RTL8367B, so drop it from switch-case in rtl8367b_extif_set_mode. ref (RTL8367): - TL-WR2453ND v1 ref (RTL8367B): - ASUS RT-N56U - TP-Link Archer C2 v1 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* imagebuilder: Remove json_info_files/ before buildPaul Spooren2020-06-111-0/+1
| | | | | | | | | | | | | | The folder `json_info_files` contains multiple JSON files which describe created firmware images. The folder is not removed between builds as the ImageBuilder does not use `image.mk`. Not removing the JSON files result in a merged `profiles.json` file containing entries for outdated or non-existing images. This commit adds the `json_info_files/` cleanup step to the ImageBuilder Makefile. Signed-off-by: Paul Spooren <mail@aparcar.org>
* imagebuilder: pass IB=1 on checking requirementsPaul Spooren2020-06-111-1/+1
| | | | | | | | | | | The patch 4a1a58a3 build, imagebuilder: Do not require libncurses-dev was supposed to remove libncurses as a requirement for the ImageBuilder. However as the IB=1 is only exported during building, not for checking requirements, it did never actually work. This commit export IB=1 to the requirement check. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: fix port display for D-Link DIR-810LAdrian Schmutzler2020-06-111-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | The port order displayed in LuCI is currently inverted for this devices: LuCI - Device LAN1 - LAN4 LAN2 - LAN3 LAN3 - LAN2 LAN4 - LAN1 Fix it. Strangely, the owner of a TRENDnet TEW-810DR reports that the initial port order is correct, while both devices share the same board and look similar from the outside. Since I cannot investigate this without having any of the devices, this does only touch the DIR-810L for now. While at it, also merge in the case for zbtlink,zbt-we2026, as the display port specified for WAN there won't have any effect anyway. Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: switch to upstream NAND patchesÁlvaro Fernández Rojas2020-06-119-35/+191
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: fix WAN LED for D-Link DIR-810L/TRENDnet TEW-810DRAdrian Schmutzler2020-06-114-20/+19
| | | | | | | | | | | | | | | | | | The WAN LED on DIR-810L was actually blinking on LAN1 port activity. This has already been improved for the TEW-810DR, where the GPIO has been set up explicitly rather than having it controlled by the switch. This patch also applies this setup to the DIR-810L. In addition, the trigger in 01_leds is set up with ucidef_set_led_switch for both devices now, so state changes should be displayed correctly as well. Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L] Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
* soloscli: fix uci-defaults fileAdrian Schmutzler2020-06-112-3/+1
| | | | | | | | | | The folder for the uci-defaults file of this package is wrong, so the file most probably has not been executed at all for several years at least. Fix the folder and remove the useless shebang for the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* apm821xx: move device definitions to subfilesAdrian Schmutzler2020-06-113-158/+152
| | | | | | | | | | | | With several subtargets, the image/Makefile becomes crowded after a while. Many targets have moved their device definitions to $subtarget.mk files to have them more organized, let's do this here as well. While at it, also move subtarget-specific build recipes. Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: simplify inclusion of subtarget image filesAdrian Schmutzler2020-06-1111-72/+15
| | | | | | | | | | | | | | Many target use a repetitive if-include scheme for their subtarget image files, though their names are consistent with the subtarget names. This patch removes these redundant conditions and just uses the variable for the include where the target setup allows it. For sunxi, this includes a trivial rename of the subtarget image Makefiles. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for the Netgear WNDRMAC v1Renaud Lepage2020-06-115-1/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2 Specifications ============== * SoC: Atheros AR7161 * RAM: 64mb * Flash on board: 16mb * WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n) * Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit) * Power: 12 VDC, 2.5 A * Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1) Flash Instructions ================== It is possible to use the OEM Upgrade page to install the `factory` variant of the firmware. After the initial upgrade, you will need to telnet into the router (default IP 192.168.1.1) to install anything. You may install LuCI this way. At this point, you will have a web interface to configure OpenWRT on the WNDRMAC v1. Please use the `sysupgrade` variant for subsequent flashes. Recovery Instructions ===================== A TFTP-based recovery flash is possible if the need arises. Please refer to the WNDR3700 page on openwrt.org for details. https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery Signed-off-by: Renaud Lepage <root@cybikbase.com> [update DTSI include name] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for the Netgear WNDRMAC v2Renaud Lepage2020-06-114-4/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear WNDRMAC v2 is a hardware variant of the Netgear WNDR3800 Specifications ============== * SoC: Atheros AR7161 * RAM: 128mb * Flash on board: 16mb * WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n) * Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit) * Serial console: Yes, 115200 / 8N1 (JTAG) * USB: 1x2.0 * Power: 12 VDC, 2.5 A * Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v2) Flash Instructions ================== It is possible to use the OEM Upgrade page to install the `factory` variant of the firmware. After the initial upgrade, you will need to telnet into the router (default IP 192.168.1.1) to install anything. You may install LuCI this way. At this point, you will have a web interface to configure OpenWRT on the WNDRMAC v2. Please use the `sysupgrade` variant for subsequent flashes. Recovery Instructions ===================== A TFTP-based recovery flash is possible if the need arises. Please refer to the WNDR3800 page on openwrt.org for details. https://openwrt.org/toh/netgear/wndr3800#recovery_flash_in_failsafe_mode Signed-off-by: Renaud Lepage <root@cybikbase.com> [do not add device to uboot-envtools, update DTSI name] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename DTSI for Netgear WNDR devices based on ar7161Adrian Schmutzler2020-06-115-4/+4
| | | | | | | This renames the DTSI for Netgear WNDR devices based on ar7161 to indicate that the file is not limited to WNDR3700 models. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: limit uci commit to the changed config fileAdrian Schmutzler2020-06-111-1/+1
| | | | | | | Since 01_enable_packet_steering only touches the network config, limit the uci commit to this as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use amber LED for boot/failsafe on Netgear EX3700/EX6130Adrian Schmutzler2020-06-112-16/+16
| | | | | | | | | According to the manual, the amber power LED is used to indicate boot, while the green LED is meant to indicate a running system. While at it, also adjust the DT node names for all LEDs. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear EX6120Adrian Schmutzler2020-06-116-2/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * CPU: 580 MHz * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The device is identical to the EX6130 except for the mains socket and the hardware ID. Installation: The -factory images can be flashed from the device's web interface or via nmrpflash. Notes: MAC addresses were set up based on the EX6130 setup. This is based on prior work of Adam Serbinski and Mathias Buchwald. Tested by Mathias Buchwald. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add mt7621 ethernet driver improvementsFelix Fietkau2020-06-102-0/+98
| | | | | | | - Speed up MDIO bus access - Improve performance on tx completion Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport upstream DSA GRO supportFelix Fietkau2020-06-101-0/+143
| | | | | | Should improve performance Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: enable packet steering by default on mt7621Felix Fietkau2020-06-101-0/+4
| | | | | | | It provides a significant performance boost, especially with flow offloading enabled Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: disable receive packet steering for DSA slave devicesFelix Fietkau2020-06-101-4/+9
| | | | | | | It is already handled on the master device. Doing it twice reduces performance Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: enable hostapd 802.11ax support if kmod-mt7915e is selectedFelix Fietkau2020-06-101-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 03:54:42 +0000