aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mt76: update to the latest versionFelix Fietkau2021-05-131-3/+3
| | | | | | | | | | | | | | | | | | | | | | Includes fix for CVE-2020-24588 c7dd54a22e30 mt76: connac: skip wtbl reset on sta disconnect 3511fd430356 mt76: validate rx A-MSDU subframes aedc3145de6e mt76: fix possible NULL pointer dereference in mt76_tx 5c2baab92cd0 mt76: mt7615: fix NULL pointer dereference in tx_prepare_skb() af21659ee834 mt76: mt76x0: use dev_debug instead of dev_err for hw_rf_ctrl e423c16f16f7 mt76: mt7615: free irq if mt7615_mmio_probe fails f2d0da8da9b7 mt76: mt7663: enable hw rx header translation d2713a5d9de9 mt76: mt7921: fix mt7921_wfsys_reset sequence ce5f32d84f33 mt76: mt7921: Don't alter Rx path classifier 8ab8c7747197 mt76: connac: fw_own rely on all packet memory all being free a747b0bb4956 mt76: mt7921: enable deep sleep at runtime 2e6e999509b1 mt76: mt7921: add deep sleep control to runtime-pm knob 30bcb2338ce2 mt76: connac: fix WoW with disconnetion and bitmap pattern 56518f4a126e mt76: mt7921: consider the invalid value for to_rssi e969ab10a034 mt76: mt7921: add back connection monitor support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* busybox: update to 1.33.1Nick Hainke2021-05-125-132/+3
| | | | | | | | | | | | | | Remove backports: - 001-backport1330fix-ash-make-strdup-copy.patch - 002-backport1330fix-traceroute.patch - 005-backport-CVE-2021-28831.patch Remove upstreamed: - 010-fix-wrong-variable.patch Signed-off-by: Nick Hainke <vincent@systemli.org> [don't use $(AUTORELEASE) for now] Signed-off-by: Paul Spooren <mail@aparcar.org>
* mac80211: backport upstream fixes for FragAttacksFelix Fietkau2021-05-1223-7/+1466
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From the patch series description: Several security issues in the 802.11 implementations were found by Mathy Vanhoef (New York University Abu Dhabi), who has published all the details at https://papers.mathyvanhoef.com/usenix2021.pdf Specifically, the following CVEs were assigned: * CVE-2020-24586 - Fragmentation cache not cleared on reconnection * CVE-2020-24587 - Reassembling fragments encrypted under different keys * CVE-2020-24588 - Accepting non-SPP A-MSDU frames, which leads to payload being parsed as an L2 frame under an A-MSDU bit toggling attack * CVE-2020-26139 - Forwarding EAPOL from unauthenticated sender * CVE-2020-26140 - Accepting plaintext data frames in protected networks * CVE-2020-26141 - Not verifying TKIP MIC of fragmented frames * CVE-2020-26142 - Processing fragmented frames as full frames * CVE-2020-26143 - Accepting fragmented plaintext frames in protected networks * CVE-2020-26144 - Always accepting unencrypted A-MSDU frames that start with RFC1042 header with EAPOL ethertype * CVE-2020-26145 - Accepting plaintext broadcast fragments as full frames * CVE-2020-26146 - Reassembling encrypted fragments with non-consecutive packet numbers * CVE-2020-26147 - Reassembling mixed encrypted/plaintext fragments In general, the scope of these attacks is that they may allow an attacker to * inject L2 frames that they can more or less control (depending on the vulnerability and attack method) into an otherwise protected network; * exfiltrate (some) network data under certain conditions, this is specific to the fragmentation issues. A subset of these issues is known to apply to the Linux IEEE 802.11 implementation (mac80211). Where it is affected, the attached patches fix the issues, even if not all of them reference the exact CVE IDs. In addition, driver and/or firmware updates may be necessary, as well as potentially more fixes to mac80211, depending on how drivers are using it. Specifically, for Intel devices, firmware needs to be updated to the most recently released versions (which was done without any reference to the security issues) to address some of the vulnerabilities. To have a single set of patches, I'm also including patches for the ath10k and ath11k drivers here. We currently don't have information about how other drivers are, if at all, affected. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: kernel2minor: work around path length limitFrançois Chavant2021-05-121-2/+5
| | | | | | | | | | | | | | When building for MikroTik devices the kernel2minor tool will sometimes fail with: Can't get lstat from kernel file!: No such file or directory. This is because kernel2minor expects paths no longer than 250 chars. To work around this the include/image-commands.mk has been modified to copy the kernel to a temporary file (/tmp/tmp.XXXXXXXXXX) before calling kernel2minor. Signed-off-by: François Chavant <francois@chavant.info>
* busybox: add SRV support to nslookup_lede.c patchPerry Melange2021-05-122-2/+22
| | | | | | | | | | Add support for querying and parsing SRV DNS records to nslookup_lede.c This patch is based on http://lists.busybox.net/pipermail/busybox/2019-June/087359.html Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com> [reword subject, bump PKG_RELEASE] Signed-off-by: Paul Spooren <mail@aparcar.org>
* base-files: shinit: properly handle dashes in service namesJo-Philipp Wich2021-05-121-1/+1
| | | | | Fixes: FS#3801 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* build: fix opkg install step for large package selectionAlexander Egorenkov2021-05-121-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the list of packages to be installed in a built image exceeds a certain number, then 'opkg install' executed for target '$(curdir)/install' in package/Makefile fails with: /usr/bin/env: Argument list too long. On Linux, the length of a command-line parameter is limited by MAX_ARG_STRLEN to max 128 kB. * https://elixir.bootlin.com/linux/latest/source/include/uapi/linux/binfmts.h#L15 * https://www.in-ulm.de/~mascheck/various/argmax/ To solve the problem, store the package list being passed to 'opkg install' in a temporary file and use the shell command substitution to pass the content of the file to 'opkg install'. This guarantees that the length of the command-line parameters passed to the bash shell is short. The following bash script demonstrates the problem: ---------------------------------------------------------------------------- count=${1:-1000} FILES="" a_file="/home/egorenar/Repositories/openwrt-rel/bin/targets/alpine/generic/packages/base-files_1414-r16464+19-e887049fbb_arm_cortex-a15_neon-vfpv4.ipk" for i in $(seq 1 $count); do FILES="$FILES $a_file" done env bash -c "echo $FILES >/dev/null" echo "$FILES" | wc -c ---------------------------------------------------------------------------- Test run: ---------------------------------------------------------------------------- $ ./test.sh 916 130989 $ ./test.sh 917 ./test.sh: line 14: /bin/env: Argument list too long 131132 ---------------------------------------------------------------------------- Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net> [reword commit subject] Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: add kmod-leds-uledsKeith T. Garner2021-05-121-0/+14
| | | | | | | | | The allows userspace LEDs to be created and controlled. This can be useful for testing triggers and can also be used to implement virtual LEDs. Signed-off-by: Keith T. Garner <kgarner@kgarner.com> [squash fixup commit and improve option wording] Signed-off-by: Paul Spooren <mail@aparcar.org>
* generic: platform/mikrotik: release mtd device after useThibaut VARÈNE2021-05-122-2/+10
| | | | | | | | | | | | The code uses get_mtd_device_nm() which must be followed by a call to put_mtd_device() once the handle is no longer used. This fixes spurious shutdown console messages such as: [ 2256.334562] Removing MTD device #7 (soft_config) with use count 1 Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* kernel: move three accepted patches from pending to backportsDaniel Golle2021-05-113-1/+1
| | | | | | | | | | | | | | | 311-MIPS-zboot-put-appended-dtb-into-a-section.patch commit d2e850e96183 in kernel, part of v5.11 499-mtd-don-t-lock-when-recursively-deleting-partitions.patch commit cb4543054c5c in kernel, part of v5.13 103-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch commit 5a4fa44f5e1b in kernel, part of v5.13 Move them to backports folder to make maintainance easier. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: fix mac addresses of Youku YK1Shiji Yang2021-05-102-3/+4
| | | | | | | | | | | | | | MAC addresses read from official firmware value location Wlan xx 71 de factory@0x04 Lan xx 71 dd factory@0x28 Wan xx 71 df factory@0x2e Label xx 71 dd factory@0x28 Signed-off-by: Shiji Yang <yangshiji66@qq.com> [fix sorting in 02_network, redact commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use standard naming scheme for Zyxel NR7101 LED nodesAdrian Schmutzler2021-05-101-7/+7
| | | | | | | Make naming and DT label consistent with other devices at this target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mt76: update to the latest versionFelix Fietkau2021-05-101-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 186af01047b2 mt76: mt7921: introduce MCU_EVENT_LP_INFO event parsing 93b5c28c97d5 mt76: mt7921: add rcu section in mt7921_mcu_tx_rate_report a8e89c5a1d1f mt76: testmode: add support to send larger packet a0cc9a9e3877 mt76: mt7915: rework mt7915_tm_set_tx_len() c8b96630324e mt76: mt7915: fix rate setting of tx descriptor in testmode 22fd2958c42a mt76: mt7615: fix memleak when mt7615_unregister_device() 7401e0db3143 mt76: mt7915: fix memleak when mt7915_unregister_device() c3656268b3f6 mt76: mt7915: only free skbs after mt7915_dma_reset() when reset happens 0ce955b04ba8 mt76: mt7615: only free skbs after mt7615_dma_reset() when reset happens b03d1e62acf7 mt76: mt7615: use ieee80211_free_txskb() in mt7615_tx_token_put() 5ac02e22fb03 mt76: flush tx status queue on DMA reset c71f609b398a mt76: sync with upstream changes 23ecadd4af77 mt76: mt7615: fix hardware error recovery for mt7663 57a899ee3c3c mt76: mt7615: fix entering driver-own state on mt7663 42a2dddb706b mt76: mt7615: load ROM patch before checking patch semaphore status cf0e406af84a mt76: mt7915: add support for applying pre-calibration data 459940ccbc58 mt76: mt7921: move hw configuration in mt7921_register_device 0a094b11f3c0 mt76: improve mcu error logging bf536832e37d mt76: mt7921: run mt7921_mcu_fw_log_2_host holding mt76 mutex 7616f4f78163 mt76: mt7921: add wifisys reset support in debugfs e620bd881ef5 mt76: mt7921: abort uncompleted scan by wifi reset e8dacf59ab1c mt76: mt7915: rework the flow of txpower setting c8c78e577236 mt76: mt7915: directly read per-rate tx power from registers 1622bf4f8705 mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device ef96fafad8a9 mt76: Convert to DEFINE_SHOW_ATTRIBUTE 90e4bfea2948 mt76: mt7921: do not use 0 as NULL pointer 0a139d7f5966 mt76: connac: move mcu_update_arp_filter in mt76_connac module de26c73ce3c2 mt76: mt7921: remove leftover function declaration 1c0b6cb4f942 mt76: mt7921: fix a race between mt7921_mcu_drv_pmctrl and mt7921_mcu_fw_pmctrl 2923e3e2b8e4 mt76: mt7663: fix a race between mt7615_mcu_drv_pmctrl and mt7615_mcu_fw_pmctrl 74d0fdaa7a99 mt76: connac: introduce wake counter for fw_pmctrl synchronization 28c87e09a5ea mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path 36f664edc7db mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path 51b3d1a9a2b7 mt76: dma: add the capability to define a custom rx napi poll routine 4f1339c9fb72 mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi 1bc5e67a60be mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi 325f7b451c03 mt76: connac: unschedule ps_work in mt76_connac_pm_wake 12115052a02f mt76: connac: check wake refcount in mcu_fw_pmctrl e5d28e3cef66 mt76: connac: remove MT76_STATE_PM in mac_tx_free 475112a3cdcc mt76: mt7921: get rid of useless MT76_STATE_PM in mt7921_mac_work 112998f32d85 mt76: connac: alaways wake the device before scanning 4334f3e2fc43 mt76: mt7615: rely on pm refcounting in mt7615_led_set_config 0562380659ad mt76: connac: do not run mt76_txq_schedule_all directly acfa78df5708 mt76: connac: use waitqueue for runtime-pm ca74a4cd0722 mt76: remove MT76_STATE_PM in tx path 0c2d3e74852e mt76: mt7921: add awake and doze time accounting 45e0eefffe9f mt76: mt7921: enable sw interrupts fd2ff641166f mt76: mt7615: Fix a dereference of pointer sta before it is null checked 7e2521468767 mt76: mt7921: move mt7921_dma_reset in dma.c c9dd6b1fa171 mt76: mt7921: introduce mt7921_wpdma_reset utility routine 2ac7c7e9c568 mt76: mt7921: introduce mt7921_dma_{enable,disable} utilities 662a89f2b9d1 mt76: mt7921: introduce mt7921_wpdma_reinit_cond utility routine 614efe9e9180 mt76: connac: introduce mt76_connac_mcu_set_deep_sleep utility 0dbb16ef39d8 mt76: mt7921: enable deep sleep when the device suspends 3c19f569cc70 mt76: mt7921: fix possible invalid register access ade1f5aad4c6 mt76: move token_lock, token and token_count in mt76_dev 8d5c456be1ff mt76: move token utilities in mt76 common module fb04d9df5e52 mt76: mt7915: do not read rf value from efuse in flash mode 2126b2176336 mt76: mt7921: get rid of mcu_reset function pointer d325b7eff1b1 mt76: mt7921: improve doze opportunity 2ae25c7e547e mt76: mt7663: add awake and doze time accounting 349bbb9d6f13 mt76: connac: unschedule mac_work before going to sleep 98a235004dea mt76: mt7921: mt7921_stop should put device in fw_own state 63d80b9ab251 mt76: mt7921: introduce mt7921_mcu_sta_add routine 3c5bf837fdbd mt76: mt7615: fix a precision vs width bug in printk ded14da5eacc mt76: mt7915: fix a precision vs width bug in printk aaf0d254f9ea mt76: mt7921: fix a precision vs width bug in printk 757af5c67d32 mt76: move mt76_token_init in mt76_alloc_device ed41ed73a495 mt76: mt7921: reinit wpdma during drv_own if necessary 92fb81e085c6 mt76: mt7921: fix possible AOOB issue in mt7921_mcu_tx_rate_report 53d915a23bc9 mt76: connac: do not schedule wake_work if the runtime-pm is disabled 23fe1bdcf15a mt76: connac: do not schedule mac_work if the device is not running e5b19336c58e mt76: mt7615: do not set MT76_STATE_PM at bootstrap 0fc2136a61dd mt76_connac_mcu: move mt76_connac_mcu_update_arp_filter outside of CONFIG_PM e693f3e23e06 mt76: mt7915: add MSI support 5231e7300fa4 mt7915: disable ASPM 554b50dabf54 mt76: connac: fix uninitialized HT A-MPDU setting field in STA_REC_PHY 43b9c0a838bb mt76: mt7921: fix max aggregation subframes setting 5a387a0a3004 mt76: mt7921: enable rx hw de-amsdu c8cbcb87be07 mt76: connac: add missing configuration in mt76_connac_mcu_wtbl_hdr_trans_tlv 55921e57b380 mt76: mt7921: enable rx header traslation offload 01441f67d8b2 mt76: mt7921: enable rx csum offload c9ab76dd93a0 mt76: mt7915: move mt7915_queue_rx_skb to mac.c caedb4c4ee41 mt76: mt7615: fix fixed-rate tx status reporting c6ae95d43e6d mt76: improve tx status codepath 27d468d094e6 mt76: mt7915: rework tx rate reporting 3b4ca5b09e2c mt76: mt7615: avoid use of ieee80211_tx_info_clear_status e1f07d7f1cb9 mt76: mt7603: avoid use of ieee80211_tx_info_clear_status 18513ba5fbc2 mt76: mt7915: add support for tx status reporting 35f189cf81b2 mt76: mt7915: fix uninitialized variable in MSI error handling 9e928ac1ea9b mt76: dma: use ieee80211_tx_status_ext to free packets when tx fails 628eee9c386c mt76: fill queue entry wcid for all skbs with a station a9bc4d94b7a1 mt76: intialize tx queue entry wcid to 0xffff by default 998ca8af7d17 mt76: mt7915: fix tssi indication field of DBDC NICs 7dd24b3cfacf mt76: mt7915: fix a signedness bug in mt7915_mcu_apply_tx_dpd() 535025d65d8d mt76: mt7915: cleanup mt7915_mcu_sta_rate_ctrl_tlv() ff8bbe22dd87 mt76: mt7915: add .set_bitrate_mask() callback Signed-off-by: Felix Fietkau <nbd@nbd.name>
* rpcd: set correct PKG_SOURCE_DATEDaniel Golle2021-05-101-1/+1
| | | | | | | | The previous commit bumped the source commit level without reflecting that in PKG_SOURCE_DATA. Bump PKG_SOURCE_DATA as well. Fixes: 97e820c6d6 ("rpcd: update to latest HEAD") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* rpcd: update to latest HEADDavid Bauer2021-05-101-2/+2
| | | | | | 7a560a1 iwinfo: add 802.11ax HE support Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: fix error handling for of_get_phy_modeDavid Bauer2021-05-101-3/+3
| | | | | | | Errors are not indicated by the phy_mode value but returned separately from the function. Signed-off-by: David Bauer <mail@david-bauer.net>
* realtek: Fix VLAN issues introduced by multicast patchesBirger Koblitz2021-05-093-5/+5
| | | | | | | | | | This adds the CPU port to the unknown multicast flooding port mask, which fixes the VLAN issues introduced by the multicast group patches Tested-by: Russell Senior <russell@personaltelco.net> [Netgear GS108Tv3] Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> [whitespace fix] Signed-off-by: Petr Štetiar <ynezz@true.cz> [unknwon typo fix]
* kernel: bump 5.10 to 5.10.35Kevin Darbyshire-Bryant2021-05-0915-98/+46
| | | | | | | | | | Refresh kernel patches. Built under MacOS Run tested: x86_64 (apu2) Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 5.10 to 5.10.34Kevin Darbyshire-Bryant2021-05-091-2/+2
| | | | | | Nothing required refreshing, simplest kernel bump you've ever seen. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: mt7621: Add support for ZyXEL NR7101Bjørn Mork2021-05-097-0/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE with integrated directional 5G/LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7603E - Switch: 1 LAN port (Gigabiti) - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC - SIM: 2 micro-SIM slots under transparent cover - Buttons: Reset, WLAN under same cover - LEDs: Multicolour green/red/yellow under same cover (visible) - Power: 802.3at PoE via LAN port The device is built as an outdoor ethernet to 5G/LTE bridge or router. The Wifi interface is intended for installation and/or temporary management purposes only. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Remove the SIM/button/LED cover, the WLAN button and 12 screws holding the back plate and antenna cover together. The GPS antenna is fixed to the cover, so be careful with the cable. Remove 4 screws fixing the antenna board to the main board, again being careful with the cables. A bluetooth TTL adapter is recommended for permanent console access, to keep the router water and dustproof. The 3.3V pin is able to power such an adapter. MAC addresses: OpenWrt OEM Address Found as lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex) wwan0 usb0 random WARNING!! ISP managed firmware might at any time update itself to a version where all known workarounds have been disabled. Never boot an ISP managed firmware with a SIM in any of the slots if you intend to use the router with OpenWrt. The bootloader lock can only be disabled with root access to running firmware. The flash chip is physically inaccessible without soldering. Installation from OEM web GUI: - Log in as "supervisor" on https://172.17.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Installation from OEM ssh: - Log in as "root" on 172.17.1.1 port 22022 - scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp - Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit - Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Copying OpenWrt to the recovery partition: - Verify that you are running a working OpenWrt recovery image from flash - ssh to root@192.168.1.1 and run: fw_setenv CheckBypass 0 mtd -r erase Kernel2 - Wait while the bootloader mirrors Image1 to Image2 NOTE: This should only be done after successfully booting the OpenWrt recovery image from the primary partition during installation. Do not do this after having sysupgraded OpenWrt! Reinstalling the recovery image on normal upgrades is not required or recommended. Installation from Z-Loader: - Halt boot by pressing Escape on console - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - Sysupgrade to the OpenWrt sysupgrade image NOTE: ATNR will write the recovery image to both primary and recovery partitions in one go. Booting from RAM: - Halt boot by pressing Escape on console - Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu - Press "4" to select "4: Entr boot command line interface." - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Load it using "tftpboot 0x88000000 initramfs-recovery.bin" - Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL header This method can also be used to RAM boot OEM firmware. The warning regarding OEM applies! Never boot an unknown OEM firmware, or any OEM firmware with a SIM in any slot. NOTE: U-Boot configuration is incomplete (on some devices?). You may have to configure a working mac address before running tftp using "setenv eth0addr <mac>" Unlocking the bootloader: If you are unebale to halt boot, then the bootloader is locked. The OEM firmware locks the bootloader on every boot by setting DebugFlag to 0. Setting it to 1 is therefore only temporary when OEM firmware is installed. - Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware - Run "fw_setenv DebugFlag 0x1" in OpenWrt NOTE: OpenWrt does this automatically on first boot if necessary NOTE2: Setting the flag to 0x1 avoids the reset to 0 in known OEM versions, but this might change. WARNING: Writing anything to flash while the bootloader is locked is considered extremely risky. Errors might cause a permanent brick! Enabling management access from LAN: Temporary workaround to allow installing OpenWrt if OEM firmware has disabled LAN management: - Connect to console - Log in as "root" - Run "iptables -I INPUT -i br0 -j ACCEPT" Notes on the OEM/bootloader dual partition scheme The dual partition scheme on this device uses Image2 as a recovery image only. The device will always boot from Image1, but the bootloader might copy Image2 to Image1 under specific conditions. This scheme prevents repurposing of the space occupied by Image2 in any useful way. Validation of primary and recovery images is controlled by the variables CheckBypass, Image1Stable, and Image1Try. The bootloader sets CheckBypass to 0 and reboots if Image1 fails validation. If CheckBypass is 0 and Image1 is invalid then Image2 is copied to Image1. If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to Image2. If CheckBypass is 1 then all tests are skipped and Image1 is booted unconditionally. CheckBypass is set to 1 after each successful validation of Image1. Image1Try is incremented if Image1Stable is 0, and Image2 is copied to Image1 if Image1Try is 3 or larger. But the bootloader only tests Image1Try if CheckBypass is 0, which is impossible unless the booted image sets it to 0 before failing. The system is therefore not resilient against runtime errors like failure to mount the rootfs, unless the kernel image sets CheckBypass to 0 before failing. This is not yet implemented in OpenWrt. Setting Image1Stable to 1 prevents the bootloader from updating Image1Try on every boot, saving unnecessary writes to the environment partition. Keeping an OpenWrt initramfs recovery as Image2 is recommended primarily to avoid unwanted OEM firmware boots on failure. Ref the warning above. It enables console-less recovery in case of some failures to boot from Image1. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* firmware-utils: zytrx: Add util for ZyXEL specific headerBjørn Mork2021-05-092-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NR7101 prepend an additional header to U-Boot images. This header use the TRX magic 0x30524448 (HDR0), but is incompatible with TRX images. This code is reverse-engineered based on matching 32 bit numbers found in the header with lengths and different checksum calculations of the vendor images found on the device. The result was matched against the validation output produced by the bootloader to name the associated header fields. Example bootloader validation output: Zyxel TRX Image 1 --> Found! Header Checksum OK ============ZyXEL header information================== chipId : MT7621A boardId : NR7101 modelId : 07 01 00 01 kernel_len : (14177560) kernelChksum : (0x8DD31F69) swVersionInt : 1.00(ABUV.0)D1 swVersionExt : 1.00(ABUV.0)D1 Zyxel TRX Image 2 --> Found! Header Checksum OK ============ZyXEL header information================== chipId : MT7621A boardId : NR7101 modelId : 07 01 00 01 kernel_len : (14176660) kernelChksum : (0x951A7637) swVersionInt : 1.00(ABUV.0)D0 swVersionExt : 1.00(ABUV.0)D0 ================================================= Check image validation: Image1 Header Magic Number --> OK Image2 Header Magic Number --> OK Image1 Header Checksum --> OK Image2 Header Checksum --> OK Image1 Data Checksum --> OK Image2 Data Checksum --> OK Image1 Stable Flag --> Stable Image1 Try Counter --> 0 Image1: OK Image2: OK The coverage and algorithm for the kernelChksum field is unknown. This field is not validated by the bootloader or the OEM firmware upgrade tool. It is therefore set to a static value for now. The swVersion fields contain free form string values. The OEM firmware use ZyXEL structured version numbers as shown above. The strings are not interpreted or validated on boot, so they can be repurposed for anything we want the bootloader to display to the user. But the OEM web GUI fails to flash images with freeform strings. The purpose of the other strings in the header is not known. The values appear to be static. We assume they are fixed for now, until we have other examples. One of these strings is the platform name, which is taken as an input parameter for support other members of the device family. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* treewide: consolidate named GPIO patch into hack-5.10Ilya Lipnitskiy2021-05-093-337/+0
| | | | | | | | | ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export functionality. Consolidate the patch that adds it under hack-5.10 since this logic is obviously not target-specific. For those who want to disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ipq806x: Bring missing patches from 5.4 to 5.10Mark Mentovai2021-05-092-0/+119
| | | | | | | | | | | | | | Kernel 5.10 support for ipq806x was added at the same time that these patches were developed for kernel 5.4. This carries the patches forward to kernel 5.10. fa731838c524 ipq806x: dwmac: clear forced speed during probe 75ca641f1b84 ipq806x: Add "snps,dwmac" to all gmac compatible= d62825dd77b3 ipq806x: dwmac: set forced speed when using fixed-link Signed-off-by: Mark Mentovai <mark@moxienet.com> Run-tested: ipq806x/ubnt,unifi-ac-hd Cc: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: Add mising devices to kernel 5.10Mark Mentovai2021-05-091-1/+6
| | | | | | | | | | | | | | d53be2a2e981 migrated 0069-arm-boot-add-dts-files.patch from patches-5.4 to patches-5.10, but a subsequent patch in that set, 1e25423be8ac, erroneously removed several devices: ipq8062/nec,wg2600hp3 from 3bb16185737c ipq8064/asrock,g10 from 98b86296e67d ipq8064/ubnt,unifi-ac-hd from 4e46beb31342 Signed-off-by: Mark Mentovai <mark@moxienet.com> Run-tested: ipq806x/ubnt,unifi-ac-hd Cc: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: bump 5.4 to 5.4.117John Audia2021-05-094-32/+12
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* mediatek: reserve memory for ramoops and enable PSTOREDaniel Golle2021-05-086-13/+65
| | | | | | | Reserve 64KiB of memory for crashlogs and enable PSTORE feature in kernel config for MT7622. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediaktek: add support for PSTORE and check it on bootDaniel Golle2021-05-085-15/+131
| | | | | | | | Add support for pstore/ramoops now that DRAM content is preserved over reboot on MT7622. On each boot, check pstore and boot to recovery image in case there are records stored in it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: update to git HEADDaniel Golle2021-05-081-3/+3
| | | | | | | Most notably this enabled use of pstore/ramoops on MT7622 as DRAM content is now preserved over reboot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq806x: ecw5410: case-insensitive qcom-smem partitionsStefan Lippers-Hollmann2021-05-082-4/+20
| | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switches to normalizing the partition names to lower case. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: g10: case-insensitive qcom-smem partitionsStefan Lippers-Hollmann2021-05-082-3/+15
| | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switches to normalizing the partition names to lower case. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: nbg6817: case-insensitive qcom-smem partitionsStefan Lippers-Hollmann2021-05-083-6/+24
| | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switches to normalizing the partition names to lower case. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: dwmac: fix GMACs connected via SGMII fixed-linkMark Mentovai2021-05-081-6/+56
| | | | | | | | | | | | | | | | | | | | | | fa731838c524 cleared the forced speed in the QSGMII PCS_ALL_CH_CTL register during probe, but this is only correct for GMACs that are not configured with fixed-link. This prevented GMACs configured with both phy-mode = "sgmii" and fixed-link from working properly, as discussed at https://github.com/openwrt/openwrt/pull/3954#issuecomment-834625090 and the comments that follow. Notably, this prevented all communication between gmac2 and the switch on the Netgear R7800. The correct behavior is to set the QSGMII PCS_ALL_CH_CTL register by considering the gmac's fixed-link child, setting the speed as directed by fixed-link if present, and otherwise clearing it as was done previously. Fixes: fa731838c524 ("ipq806x: dwmac: clear forced speed during probe") Signed-off-by: Mark Mentovai <mark@moxienet.com> Tested-by: Hannu Nyman <hannu.nyman@iki.fi> Run-tested: ipq806x/ubnt,unifi-ac-hd, ipq806x/netgear,r7800 Cc: Petr Štetiar <ynezz@true.cz> Cc: Ansuel Smith <ansuelsmth@gmail.com> Tested-by: Ansuel Smith <ansuelsmth@gmail.com>
* Extend checks on build prerequisites for building OpenWRT coreBas Mevissen2021-05-081-1/+12
| | | | | | | | | | | | | OpenWRT requires a number of Perl modules to be installed. It wasn't checking on all of them. This patch adds checks for Perl FindBin, File::Copy, File::Compare and Thread::Queue modules. Failing to install these, will have the build break at some point. By adding these to the prereq-build.mk script, they are checked on forehand. Tested on a Fedora 33 and 34 (beta) that was freshly installed. Fedora appears to break up Perl modules into small packages that need to be installed for the build to succeed. Signed-off-by: Bas Mevissen <abuse@basmevissen.nl>
* uqmi: fix network registration loopThomas Richard2021-05-082-10/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With some debug in qmi.sh using following patch, some errors are visible in the registration step @@ -29,6 +29,7 @@ proto_qmi_init_config() { } proto_qmi_setup() { + set -x local interface="$1" local dataformat connstat plmn_mode mcc mnc local device apn auth username password pincode delay modes pdptype @@ -224,6 +225,8 @@ proto_qmi_setup() { fi done + registration=$(uqmi -s -d "$device" --get-serving-system) + [ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1 echo "Starting network $interface" During the boot of the system, modem could not start automatically its network registration. netifd: wan (9235): + echo 'Waiting for network registration' netifd: wan (9235): Waiting for network registration netifd: wan (9235): + local 'registration_timeout=0' netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system netifd: wan (9235): + grep '"searching"' netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system netifd: wan (9235): + registration='{"registration":"not_registered","plmn_mcc":208,"plmn_mnc":20,"plmn_description":"","roaming":true}' netifd: wan (9235): + '[' -n ] netifd: wan (9235): + echo 'Starting network wan' As the while loop checks only "searching" pattern, uqmi.sh script quits searching loop and continues whereas the modem is not registered Other issue, after X seconds modem stops searching. netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system netifd: wan (9213): + grep '"searching"' netifd: wan (9213): + '[' -e /dev/cdc-wdm0 ] netifd: wan (9213): + '[' 3 -lt 0 -o 0 '=' 0 ] netifd: wan (9213): + let registration_timeout++ netifd: wan (9213): + sleep 1 netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system netifd: wan (9213): + grep '"searching"' netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system netifd: wan (9213): + registration='{"registration":"not_registered"}' netifd: wan (9213): + '[' -n ] netifd: wan (9213): + echo 'Starting network wan' netifd: wan (9213): Starting network wan If registration_timeout is not expired, registration can be restarted Signed-off-by: Thomas Richard <thomas.richard@kontron.com> Tested-by: Florian Eckert <fe@dev.tdt.de>
* ipq40xx: fix hard_config partition size on MikroTik hAP-ac2Baptiste Jonglez2021-05-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The routerbootparts driver dynamically discovers the location of MikroTik partitions, but it cannot determine their size (except by extending them up to the start of the next discovered partition). The hard_config partition has a default size of 0x1000 in the driver, while it actually takes 0x2000 on the hAP-ac2. Set the correct size in the hAP-ac2 DTS. On most devices, this isn't a problem as the actual data fits in 0x1000 bytes. However, some devices have larger data that doesn't fit in 0x1000 bytes. In any case, all devices seen so far have enough space for a 0x2000 hard_config partition before the start of the dtb_config partition. With the current 0x1000 size: 0x00000000e000-0x00000000f000 : "hard_config" 0x000000010000-0x000000017bbc : "dtb_config" With this patch extending the size to 0x2000: 0x00000000e000-0x000000010000 : "hard_config" 0x000000010000-0x000000017bbc : "dtb_config" Other ipq40xx boards may need the same fix but it needs testing. References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324 Acked-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* sdk: unset BINARY_FOLDER and DOWNLOAD_FOLDER in final archivesSven Roederer2021-05-081-1/+7
| | | | | | | | | | | | | | | | Using these config-options to customize the folders used at build-time makes these folder settings appear in generated archive. This causes the SDK to be not portable, as it's going to use the build-time folders on the new systems. The errors vary from passing the build, disk out-of-space to permission denied. The build-time settings of these folders are passed into the archive via Config.build. The expected behavior is that the SDK acts after unpacking like these settings have their defaults, using intree folders. So just filter these folders out when running convert-config.pl to create Config.build. This addresses the same issue that's fixed in the previous commit for the imagebuilder. Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* imagebuilder: unset BINARY_FOLDER and DOWNLOAD_FOLDER in final archiveSven Roederer2021-05-081-0/+2
| | | | | | | | | | | | | | | | | | | | | Using these config-options to customize the folders used at build-time makes these folder settings appear in generated archive. This causes the imagebuilder to be not portable, as it's going to use the build-time folders on the new systems. Errors look like: mkdir: cannot create directory '/mnt/build': Permission denied Makefile:116: recipe for target '_call_image' failed make[2]: *** [_call_image] Error 1 Makefile:241: recipe for target 'image' failed make[1]: *** [image] Error 2 The build-time settings of these folders are passed into the archives via .config file. The expected behavior is that after unpacking the imagebuilder acts like these settings have their defaults, using intree folders. So unset the build-time settings. Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* uboot-envtools: change size for unifi-6-lrDaniel Golle2021-05-071-1/+1
| | | | | | | The previous commit increased the U-Boot environment size of the UniFi 6 LR to 0x4000. Also change it uboot-envtools accordingly. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: unifi-6-lr: fix erase of production paritionDaniel Golle2021-05-072-13/+15
| | | | | | | | | | | mtd erase needs to be aligned with erase blocks. Use padded image size for erasing the production volume. As the environment grew above the current size of 0x1000 bytes by introducing the new padding function, increase the env size to 0x4000. While at it, clean up reset button function to work to more reliable on that board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: Add support for Layer 2 MulticastBirger Koblitz2021-05-075-300/+1024
| | | | | | | | | | Adds support for Layer 2 multicast by implementing the DSA port_mdb_* callbacks. The Kernel bridge listens to IGMP/MLD messages trapped to the CPU-port, and calls the Multicast Forwarding Database updates. The updates manage the L2 forwarding entries and the multicast port-maps. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Setup all VLANs with default configurationsBirger Koblitz2021-05-075-0/+75
| | | | | | | | This sets up all VLANs with a default configuration on reset: - forward based on VLAN-ID and not the FID/MSTI - forward based on the inner VLAN-ID (not outer) Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add SoC-specific VLAN setup routineBirger Koblitz2021-05-074-114/+259
| | | | | | | | This adds SoC specific VLAN configuration routines, which alsoe sets up the portmask table entries that are referred to in the vlan profiles registers for unknown multicast flooding. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add support for clause45 PHYsBirger Koblitz2021-05-076-234/+563
| | | | | | | | This adds support for the MMD access registers the RTL-SoCs use to access clause 45 PHYs via mdio. This new interface is used to add EEE-support for the RTL8226 Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: improve EEE support for RTL8380/8390/9300Birger Koblitz2021-05-075-33/+301
| | | | | | | Clean up and fix bugs in the EEE support for RTL8380/90 Adds EEE support for RTL9300 Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add L2 hash bucket sizeBirger Koblitz2021-05-072-3/+5
| | | | | | | | Adds a hash-bucket size attribute for the different SoCs, in order to accomodate the buckets with 8 entries of the L2-forwarding tables on RTL93XX in contrast to only 4 on RTL83XX. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: remove unused FDB print routingBirger Koblitz2021-05-071-21/+0
| | | | | | remove fdb_dump debugging function Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add IGMP/MLD snooping supportBirger Koblitz2021-05-072-4/+7
| | | | | | | This adds snooping support for IGMP and MLD on RTL8380/90/9300 by trapping IGMP and MLD packets to the CPU. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: enable CRC offloadingBirger Koblitz2021-05-071-24/+93
| | | | | | | | | | Enables CRC calculation offloading on RTL8380/8390/9300. Tested on Zyxel XGS1210-10 (RTL9302)/GS1900-48 (RTL8390)/GS1900-10HP (RTL8382) On the Zyxel GS1900-10HP, an increase of 5% in iperf3 send throughput and 11% in receive throughput is seen. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* ipq806x: add missing wakeup-source for gpio keysAnsuel Smith2021-05-0716-0/+105
| | | | | | | wakeup-source is required for gpio keys to fix error genirq: irq_chip msmgpio did not update eff. affinity mask Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: apply correct voltage toleranceAnsuel Smith2021-05-073-77/+77
| | | | | | Voltage tolerance was 5%, not 5000. Update min and max voltage of the target opp. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 12:02:04 +0000