aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* tools: build bash on macOS and use it for ipkg-buildFelix Fietkau2022-01-273-1/+25
| | | | | | | | | On macOS, system binaries silently drop the environment variables for injecting extra shared libraries (used by fakeroot). This is done for security reasons. Work around this by building bash from source, so that it gets an ad-hoc signature and does not have these restrictions Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/coreutils: build chownFelix Fietkau2022-01-271-1/+1
| | | | | | | On ARM macOS, injecting extra shared libraries does not work for system binaries. This causes fakeroot to fail for chown calls Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/fakeroot: fix unresolved symbols on arm64 macOSFelix Fietkau2022-01-271-10/+43
| | | | | | | The $INODE64 symbol variants are not present, since the base system always uses 64-bit file offsets Signed-off-by: Felix Fietkau <nbd@nbd.name>
* sdk: ship llvm toolchainFelix Fietkau2022-01-271-2/+1
| | | | | | This allows ebpf packages like qosify to be built with it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netfilter: correct some dependenciesTiago Gaspar2022-01-271-2/+2
| | | | | | | | | | | | nf-nathelper-extra and nf-conntrack-netlink had iptables related dependencies, yet, when looking for the respective kernel symbols and checking it's dependencies it was confirmed that iptables wasn't required and that these were either it's own moodule or tool independent (nftables or iptables). Correct these and make sure no unneeded extras are pulled in. Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
* rockchip: disable UHS modes for NanoPi R4SDavid Bauer2022-01-271-0/+26
| | | | | | | | | | | The NanoPi R4S leaves the SD card in 1.8V signalling when rebooting while U-Boot requires the card to be in 3.3V mode. Remove UHS support from the SD controller so the card remains in 3.3V mode. This reduces transfer speeds but ensures a reboot whether from userspace or following a kernel panic is always working. Signed-off-by: David Bauer <mail@david-bauer.net>
* meta: create FUNDING.ymlPaul Spooren2022-01-261-0/+1
| | | | | | | By adding this file a badge should appear in the GitHub web interface to motivate people donate money to the OpenWrt project. Signed-off-by: Paul Spooren <mail@aparcar.org>
* mediatek: mt7623: include regular AHCI PCI driverDaniel Golle2022-01-251-1/+1
| | | | | | | | | The legacy image for the UniElec U7623-02 until now included kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that board uses a PCIe-connected AHCI controller for the SATA port and mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* scripts/feeds: install targets to target/linux/feeds and support overridingFelix Fietkau2022-01-241-8/+26
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* scripts/feeds: fix installing targets without explicitly specifying the feedFelix Fietkau2022-01-241-0/+2
| | | | | | Add similar code to what is done on packages Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: increase scan depth for finding targetsFelix Fietkau2022-01-241-1/+1
| | | | | | This allows targets to be put into target/linux/feeds Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: change PYTHON to python3Felix Fietkau2022-01-241-1/+1
| | | | | | | | On recent macOS, /usr/bin/python3 is a wrapper that finds the right python executable It checks argv[0] to determine if python2 or python3 should be called. Always execute it as python3 to ensure it calls the right version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: drop 5.4 kernelRobert Marko2022-01-2448-7415/+0
| | | | | | | Since 5.10 is now default, no point in keeping 5.4 around. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* uboot-mediatek: update to version 2022.01Daniel Golle2022-01-2321-111/+62
| | | | | | | Tested on BananaPi R2 (SD, eMMC), BananaPi R64 (SD, eMMC, SPI-NAND) and UniElec U7623-02 (eMMC). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: store random MAC address in U-Boot env on first bootDaniel Golle2022-01-231-0/+14
| | | | | | | For devboards without a MAC address assigned from factory, store the random MAC in U-Boot env on first boot to make it persistent. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add configuration for UniElec U7623 boardDaniel Golle2022-01-232-5/+9
| | | | | | | Add U-Boot env settings to allow accessing the environment using fw_printenv and fw_setenv tools on the UniElec U7623 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: rework images for U7623-02 boardDaniel Golle2022-01-2313-313/+95
| | | | | | | | | | | | | | | | | | | | | | Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz file once which will upgrade U-Boot and switch to the new image layout. Users of the vendor firmware need to first flash the legacy image to then sunsequently carry out a full-flash upgrade. Alternatively the board can also be flashed using MediaTek's proprietary SP Flash Tool. Configuration as well as persistent MAC address will be lost once at this point and you will have to redo (or restore) all configuration manually. To restore the previous persistent MAC address users may set it manually using fw_setenv ethaddr 00:11:22:33:44:55 For future upgrades once running OpenWrt past this commit, the usual *sysupgrade.itb file can be used. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: update build for the U7623-02 boardDaniel Golle2022-01-236-70/+273
| | | | | | | Brings bootmenu and production/recovery dual-boot scheme like on the BPi-R2, BPi-R64, E8450 and UniFi 6 LR. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add common DTS aliases for UniElec U7623 boardDaniel Golle2022-01-231-2/+8
| | | | | | | | * Use serial0 instead of serial2 for the only serial port * Add LED aliases * Add ethernet0 alias to inherit ethaddr from U-Boot env Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uml: make use of 'rootfs-part' featureDaniel Golle2022-01-232-2/+2
| | | | | | | Use 'rootfs-part' feature instead of referencing the TARGET_uml in Config-images.in. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi: make use of 'rootfs-part' featureDaniel Golle2022-01-232-2/+2
| | | | | | | Use 'rootfs-part' feature instead of referencing the TARGET_sunxi in Config-images.in. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* omap: make use of 'rootfs-part' featureDaniel Golle2022-01-232-2/+2
| | | | | | | Use 'rootfs-part' feature instead of referencing the TARGET_omap in Config-images.in. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZEDaniel Golle2022-01-233-5/+5
| | | | | | | Enable 'rootfs-part' feature to make the size of the partition of the production image configurable instead of hard-coding it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* netifd: update to git HEADHans Dedecker2022-01-231-3/+3
| | | | | | ed71876 iprule: add support for uidrange Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ucode: add temporary fix for integer formatting on 32bit systemsJo-Philipp Wich2022-01-232-1/+12
| | | | | | | | | | | | The ucode VM always passes 64bit integer values to sprintf implementation while the `%d` format expects 32bit integers on 32bit platforms, leading to incorrect formatting results. Temporarily solve the issue by casting the numeric argument to int until a more thorough fix arrives with the next update. Fixes: FS#4234 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath79: add support for GL.iNet GL-XE300Victorien Molle2022-01-222-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet GL-XE300 is a 4G LTE Wireless router, based on QCA9531 SoC. Specifications: - SoC: QCA9531 (650MHz) - RAM: DDR2 128M - Flash: SPI NOR 16M + SPI NAND 128M - WiFi: 2.4GHz with 2 antennas - Ethernet: - 1x LAN (10/100M) - 1x WAN (10/100M) - LTE: - USB: 1x USB 2.0 port - UART: - 3.3V, TX, RX, GND / 115200 8N1 MAC addresses as verified by OEM firmware: use address source LAN *:c5 art 0x0 (label) WAN *:c6 label + 1 WLAN *:c7 art 0x1002 Installation via U-Boot rescue: 1. Press and hold reset and power buttons simultaneously 2. Wait for the LAN led to blink 5 times 3. Release reset and power buttons 4. The rescue page is accessible via http://192.168.1.1 5. Select the OpenWrt factory image and start upgrade 6. Wait for the router to flash new firmware and reboot Revert to stock firmware: i. Download the stock firmware from GL.Inet website ii. Use the same method explained above to flash the stock firmware Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr> [update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: correct vendor name for COMFAST/JoowinRodrigo Araujo2022-01-227-44/+50
| | | | | | | | | | | | | | | | When Joowin WR758AC V1 and V2 devices were added, they should have been added with the primary manufacturer name which is COMFAST, since Joowin is just an alternate vendor name on some coutries or stores. Fix this by changing the the vendor name on the respective files and set Joowin as ALT0 variants while ensuring compatibility for early users. Also adjust the model names to better follow the naming rules. As a side effect, fix mt76x8 network script which was left incorrectly unsorted on the case block conditions. Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2") Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* ramips: read Tenbay T-MB5EU address from single locationDavid Bauer2022-01-221-5/+2
| | | | | | | | | | | | | Currently the WAN MAC address is read from a different offset contrary to all other addresses. There's conflicting information whether offset 0x28 on the factory partition contains the valid WAN mac for all devices while 0x4 seems to be uniform. Read the WAN mac from this location and calculate it. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: update Tenbay T-MB5EU wireless MAC addressDavid Bauer2022-01-221-2/+1
| | | | | | | | | | | | | | The current MAC address assignment is still incorrect. Use the same MAC address as seen on the stock firmware for both wireless interfaces. The 5GHz MAC address OUI is +2 in the first EUI octet. We currently don't do this in OpenWrt. Ignore this offset for now. With the current assignment, recurring MAC addresses between radios is already taken care of. Signed-off-by: David Bauer <mail@david-bauer.net>
* util-linux: Add tasksetHauke Mehrtens2022-01-211-0/+15
| | | | | | | This adds the taskset application from util Linux. It is already built, but not packaged yet. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* ltq-vdsl-mei: Remove static linkingHauke Mehrtens2022-01-211-0/+47
| | | | | | | | | This removes -static compile option. The -static option tells GCC to link this statically with the libc, which we do not want in OpenWrt. We want to link everything dynamically to the libc. This fixes a compile problem with glibc. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq806x: Netgear D7800: Fix RAM and enable PCIe #2David Woodhouse2022-01-211-1/+15
| | | | | | | This board has 512MiB of RAM like the R7800, and the VDSL modem is attached to the second PCIe port. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* ipip: add 'nohostroute' optionMatthew Hagan2022-01-192-3/+6
| | | | | | | | Add the nohostroute option as available for gre and wg tunnels to allow the user to prevent explicit creation of a route to the peer address. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ath79: add support for reset key on MikroTik RB912UAG-2HPnDDenis Kalashnikov2022-01-197-8/+282
| | | | | | | | | | | | | | | | | | | | | | On MikroTik RB91x board series a reset key shares SoC gpio line #15 with NAND ALE and NAND IO7. So we need a custom gpio driver to manage this non-trivial connection schema. Also rb91x-nand needs to have an ability to disable a polling of the key while it works with NAND. While we've been integrating rb91x-key into a firmware, we've figured out that: * In the gpio-latch driver we need to add a "cansleep" suffix to several gpiolib calls, * When gpio-latch and rb91x-nand fail to get a gpio and an error is -EPROBE_DEFER, they shouldn't report about this, since this actually is not an error and occurs when the gpio-latch probe function is called before the rb91x-key probe. We fix these related things here too. Signed-off-by: Denis Kalashnikov <denis281089@gmail.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* layerscape: switch to 5.10 KernelPaul Spooren2022-01-191-1/+1
| | | | | | | Tested by multiple users and since all targets need to be on Kernel 5.10 to be part of the next release, add changes. Signed-off-by: Paul Spooren <mail@aparcar.org>
* build: switch to firewall4 by defaultPaul Spooren2022-01-191-4/+3
| | | | | | | This commit replaces firewall aka firewall3 with its nftables based successor firewall4. Signed-off-by: Paul Spooren <mail@aparcar.org>
* mvebu: cortexa9: Fix board.d/01_ledsKlaus Kudielka2022-01-181-1/+1
| | | | | | | Fix syntax error in the case statement Fixes: 9149ed4f05f8 ("mvebu: cortexa9: Add support for Ctera C200-V2") Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
* ipq40xx: rename RT-AC42U WLAN/LAN LEDsSungbo Eo2022-01-172-8/+10
| | | | | | | | | | Assign LED numbers properly by adding function-enumerator property in DTS. While at it, remove default trigger of LAN LEDs as it will be handled in 01_leds anyway. Fixes: 51b9aef553a8 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: image: remove unused DTB_SIZE variableSungbo Eo2022-01-171-2/+0
| | | | | | It is not included in DEVICE_VARS anyways. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* treewide: drop use of whichAnsuel Smith2022-01-179-11/+20
| | | | | | | | | | | | | | Ubuntu started to flag which as deprecated and it seems which is not really standard and may vary across Distro. Drop the use of which and use the standard 'command -v' for this simple task. Which is still present in the prereq if some package/script still use which. A utility script called command_all.sh is implemented that will just mimic the output of which -a. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* build: add HOST_CXXFLAGS for host buildSergey V. Lobanov2022-01-162-0/+2
| | | | | | | Added HOST_CXXFLAGS to specify CXXFLAGS during host-compile (e.g. to specify c++ standard: HOST_CXXFLAGS += -std=c++11) Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
* firmware-utils: update to latest masterHauke Mehrtens2022-01-161-3/+3
| | | | | | d885b49 tplink-safeloader: support Archer C6v3.0 (BR) Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ustream-ssl: update to Git version 2022-01-16Hauke Mehrtens2022-01-161-4/+4
| | | | | | 868fd88 ustream-openssl: wolfSSL: Add compatibility for wolfssl >= 5.0 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* omap: add support for the TRNG Hardware AcceleratorAlexey Smirnov2022-01-161-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to TI docs (Processor SDK Linux Getting Started Guide) the Random Number Generator hardware is found on OMAP16xx, OMAP2/3/4/5, AM33xx/AM43xx boards. It already defined in device tree files. Let's enable it. Some tests: root@RTS1_OI:~# rngtest -c 1000 </dev/hwrng rngtest 6.10 Copyright (c) 2004 by Henrique de Moraes Holschuh This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. rngtest: starting FIPS tests... rngtest: bits received from input: 20000032 rngtest: FIPS 140-2 successes: 999 rngtest: FIPS 140-2 failures: 1 rngtest: FIPS 140-2(2001-10-10) Monobit: 0 rngtest: FIPS 140-2(2001-10-10) Poker: 0 rngtest: FIPS 140-2(2001-10-10) Runs: 1 rngtest: FIPS 140-2(2001-10-10) Long run: 0 rngtest: FIPS 140-2(2001-10-10) Continuous run: 0 rngtest: input channel speed: (min=198.710; avg=1265.501; max=2976.417)Kibits/s rngtest: FIPS tests speed: (min=1.780; avg=37.085; max=39.736)Mibits/s rngtest: Program run time: 15961329 microseconds Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
* ltq-deu: add ltq-deu back to default packagesDaniel Kestrel2022-01-163-7/+9
| | | | | | | | | After enhancing ltq-deu, build it by default for the devices using it. Reverts: 964863b ("ltq-deu: Mark lantiq DEU broken") Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
* ath79: use lzma-loader for ZyXEL NBG6716Lech Perczak2022-01-161-3/+3
| | | | | | | | | | | | | | | | | Since gzip-compressed kernel image stopped fitting on 4MB kernel partition on the device, use lzma-loader wrapping LZMA-compressed kernel. This yields bootable device once again, and saves a very substantial amount of space, the kernel size decreasing from about 4.4MB to about 2.5MB for 5.10 kernel. This avoids changing of the flash layout for the device. While at that, reactivate the build for the device. Fixes: 5d8ea6d34f9 ("ath79: Deactivate ZyXEL NBG6716 by default") Cc: André Valentin <avalentin@marcant.net> Cc: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Alex Henrie <alexhenrie24@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: Add support for OpenMesh OM2P v1Sven Eckelmann2022-01-167-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR7240 rev 2 * 350/350/175 MHz (CPU/DDR/AHB) * 32 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 18-24V passive POE (mode B) + used as WAN interface - eth1 + builtin switch port 4 + used as LAN interface * 12-24V 1A DC * external antenna The device itself requires the mtdparts from the uboot arguments to properly boot the flashed image and to support dual-boot (primary + recovery image). Unfortunately, the name of the mtd device in mtdparts is still using the legacy name "ar7240-nor0" which must be supplied using the Linux-specfic DT parameter linux,mtd-name to overwrite the generic name "spi0.0". Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Allow to set spi-nor mtd name via devicetreeSven Eckelmann2022-01-161-0/+54
| | | | | | | | | | | | | | | On ar71xx, it was possible to overwrite the name of the spi-nor mtd device identifier using the flash_platform_data which each mach-*.c could adjust for its devices. A similar feature was introduced for mtd-physmap in devicetree's. The property linux,mtd-name can be used to set the name and provide a stable identifier for mtdpart from the bootloader. But this feature is not yet available upstream for spi-nor devices which also might receive their partition layout from the bootloader. But the OpenWrt pistachio support for this property can simply be imported into ath79 to gain this support. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM5P-AC v2Sven Eckelmann2022-01-164-33/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* lantiq: backport latest upstream patchesAleksander Jan Bajkowski2022-01-163-0/+266
| | | | | | | | | | | | This patch includes a series of performance improvements. All patches were accepted and should land in 5.17. NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500): Down Up Before 539 Mbps 599 Mbps After 624 Mbps 695 Mbps Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-10 21:51:40 +0000