aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: Add patches for 4.19Robert Marko2018-12-2726-0/+9289
| | | | | | | | | | | | | | | | This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
* ipq40xx: Add files for 4.19Robert Marko2018-12-2716-0/+3613
| | | | | | This copies over files from 4.14 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath79: add support for devolo WiFi pro 1750cDavid Bauer2018-12-274-1/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button There is also a Micro-B USB-port present but this only seems to be a dummy as the circuit next to it is not present (at least in my unit). It is also not mentioned in the devolo manual. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1200eDavid Bauer2018-12-276-0/+214
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer C7 v5TOCK Chiu2018-12-275-1/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for TP-Link Archer C7 v5, leveraging most effort from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5 but with a different flash layout. Specification: - QCA9563 SoC (750 MHz) - 128 MiB of RAM (DDR2) - 16 MiB of flash (SPI) - 5x 1 Gbps Ethernet (1x WAN + 4x LAN) - 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880 - 10x LED, 2x button - UART header on PCB Flash instructions: 1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin via web interface. Flash instructions using TFTP recovery: 1. Plug PC to one of the LAN ports 2. Set PC to fixed IP address 192.168.0.66 3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in TFTP root directory 4. Turn on the router with the reset button pressed for about 15 secs 5. Release the button and wait about 150 secs to complete flashing Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
* brcm2708: Add feature flag rootfs-partDaniel F. Dickinson2018-12-271-1/+1
| | | | | | | | | Even with squashfs brcm2708 requires ROOTFS_PART_SIZE because the overlay exists as a loopback device on the space not used by squashfs in the root partition. Also for ext4 (the other fs option) ROOTFS_PART_SIZE is required, so use feature flag rootfs-part to enable it. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* apm821xx: sata: set rootfs-part feature flagChristian Lamparter2018-12-271-1/+1
| | | | | | | | The rootfs-part feature flag ensures that CONFIG_ROOTFS_PART_SIZE symbol will be present at all times. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* tools/e2fsprogs: Update to 1.44.5Daniel Engberg2018-12-271-2/+2
| | | | | | Update e2fsprogs to 1.44.5 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* bcm53xx: update 4.19 configRafał Miłecki2018-12-271-20/+20
| | | | | | | There were 3 new symbols possible to choose: ARCH_BCM_HR2, PCI_V3_SEMI and PHY_BCM_SR_PCIE. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: add support for the kernel 4.19Rafał Miłecki2018-12-2722-0/+2097
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport DTS changes queued for the 4.21Rafał Miłecki2018-12-279-8/+180
| | | | | | It just replaces some downstream patches & adds relicensing work. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: rename dts backport patches changing their prefixesRafał Miłecki2018-12-2716-0/+0
| | | | | | | Start 03x with 030 instead of 035. It's a trivial change that adds more place for further backports in the 03x space. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: Fix KERNEL_STACKPROTECTOR on kernel 4.19Hauke Mehrtens2018-12-262-4/+10
| | | | | | | | | | | | The configuration option was renamed with kernel 4.19 from CONFIG_CC_STACKPROTECTOR to CONFIG_STACKPROTECTOR adapt the code to set both options. CONFIG_STACKPROTECTOR now sets the regular stack protector and CONFIG_STACKPROTECTOR_STRONG activates the additional protection of more functions. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Add compiler options to generic configurationHauke Mehrtens2018-12-261-0/+6
| | | | | | | | With kernel 4.19 new configuration options for the compiler were added. These are automatically selected and set, instead of having them in each target configuration, put them into the generic configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Deactivate CONFIG_COMPAT_BRKHauke Mehrtens2018-12-268-8/+0
| | | | | | | | | CONFIG_COMPAT_BRK disables the heap randomization which is only needed for very old and ancient user space applications, I am not aware that we run any of these, just deactivate this option for these targets to allow heap randomization. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm53xx: update pinctrl driver & use its new DT bindingRafał Miłecki2018-12-252-0/+130
| | | | | | | Driver has been updated upstream to support more precise DT binding and avoid mapping conflicts between pinctrl and USB 2.0 PHY. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: MIPS: math-emu Write-protect delay slot emulation pagesKevin Darbyshire-Bryant2018-12-243-0/+357
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=adcc81f148d733b7e8e641300c5590a2cdc13bf3 "Mapping the delay slot emulation page as both writeable & executable presents a security risk, in that if an exploit can write to & jump into the page then it can be used as an easy way to execute arbitrary code. Prevent this by mapping the page read-only for userland, and using access_process_vm() with the FOLL_FORCE flag to write to it from mips_dsemul(). This will likely be less efficient due to copy_to_user_page() performing cache maintenance on a whole page, rather than a single line as in the previous use of flush_cache_sigtramp(). However this delay slot emulation code ought not to be running in any performance critical paths anyway so this isn't really a problem, and we can probably do better in copy_to_user_page() anyway in future. A major advantage of this approach is that the fix is small & simple to backport to stable kernels. Reported-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")" Without patch: cat /proc/self/maps 00400000-0047a000 r-xp 00000000 1f:03 1823 /bin/busybox 00489000-0048a000 r-xp 00079000 1f:03 1823 /bin/busybox 0048a000-0048b000 rwxp 0007a000 1f:03 1823 /bin/busybox 77ec8000-77eed000 r-xp 00000000 1f:03 2296 /lib/libgcc_s.so.1 77eed000-77eee000 rwxp 00015000 1f:03 2296 /lib/libgcc_s.so.1 77eee000-77f81000 r-xp 00000000 1f:03 2470 /lib/libc.so 77f90000-77f92000 rwxp 00092000 1f:03 2470 /lib/libc.so 77f92000-77f94000 rwxp 00000000 00:00 0 7f946000-7f967000 rw-p 00000000 00:00 0 [stack] 7fefb000-7fefc000 rwxp 00000000 00:00 0 7ffac000-7ffad000 r--p 00000000 00:00 0 [vvar] 7ffad000-7ffae000 r-xp 00000000 00:00 0 [vdso] Patch applied: cat /proc/self/maps 00400000-0047a000 r-xp 00000000 1f:03 1825 /bin/busybox 00489000-0048a000 r-xp 00079000 1f:03 1825 /bin/busybox 0048a000-0048b000 rwxp 0007a000 1f:03 1825 /bin/busybox 77ed0000-77ef5000 r-xp 00000000 1f:03 2298 /lib/libgcc_s.so.1 77ef5000-77ef6000 rwxp 00015000 1f:03 2298 /lib/libgcc_s.so.1 77ef6000-77f89000 r-xp 00000000 1f:03 2474 /lib/libc.so 77f98000-77f9a000 rwxp 00092000 1f:03 2474 /lib/libc.so 77f9a000-77f9c000 rwxp 00000000 00:00 0 7fbed000-7fc0e000 rw-p 00000000 00:00 0 [stack] 7fefb000-7fefc000 r-xp 00000000 00:00 0 7fff6000-7fff7000 r--p 00000000 00:00 0 [vvar] 7fff7000-7fff8000 r-xp 00000000 00:00 0 [vdso] Note lack of write permission to 7fefb000-7fefc000 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: fix pinmux reg size for QCA955xChristian Lamparter2018-12-241-1/+1
| | | | | | | | The range of pinmux reg property "<0x1804002c 0x40>" for QCA955x SoC does not includes GPIO_FUNCTION register. Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath10k-ct: Update to 2018-12-20Robert Marko2018-12-244-21/+21
| | | | | | | | | | | This version removes a lot of unusefull warnings that would quickly overflow the dmesg. Warnings like this: ath10k_ahb a800000.wifi: Invalid legacy rate 26 peer stats ath10k_ahb a000000.wifi: Invalid VHT mcs 15 peer stats On this version I only had 2 warnings at all. Tested on 8devices Jalapeno. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath79: add support for NEC Aterm WG800HPINAGAKI Hiroshi2018-12-245-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 1T1R (QCA9887) - 4x 10/100/1000 Mbps Ethernet - 8x LEDs, 3x keys (2x buttons, 1x slide-switch) - UART through-hole on PCB (J2) - Vcc, GND, NC, TX, RX from SoC side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WG800HP 2. Connect power cable to WG800HP and turn on it 3. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* build: move xor-image into image-commandsINAGAKI Hiroshi2018-12-242-5/+5
| | | | | | | | I moved xor-image into image-commands.mk to use it in ath79 target. It required for NEC WG800HP. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* firmware-utils: add hex pattern mode for xorimageINAGAKI Hiroshi2018-12-241-3/+36
| | | | | | | | | | | | This commit adds "hex pattern mode" to xorimage. This mode allows xor with a hexadecimal pattern that cannot be expressed with ASCII charactors. usage (example): xorimage -i firmware.bin -o firmware.bin.new -p 6A57190601121E4C -x Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (fix checkpatch)
* ath79: fix pinmux reg value for QCA956xINAGAKI Hiroshi2018-12-241-1/+1
| | | | | | | | | | | | | The range of pinmux reg property "<0x1804002c 0x40>" for QCA956x SoC does not includes GPIO_FUNCTION register. If the device uses "&jtag_disable_pins", this causes the following errors: [ 1.982937] pinctrl-single 1804002c.pinmux: mux offset out of range: 0x40 (0x40) [ 1.990622] pinctrl-single 1804002c.pinmux: could not add functions for pinmux_jtag_disable_pins 64x Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: Add missing symbols to 4.19Christian Lamparter2018-12-241-0/+1
| | | | | | Tested with apm82181 and ipq40xx minimal image versions. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* tools/mtools: Update to 4.0.23Daniel Engberg2018-12-242-21/+4
| | | | | | | Update mtools to 4.0.23 Drop patch, workaround in upstream Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* kernel: bump 4.14 to 4.14.90Kevin Darbyshire-Bryant2018-12-2410-63/+14
| | | | | | | | | | | | | | Refresh all patches Remove upstream patch: backport-4.14/424-v4.20-net-dsa-fix-88e6060-roaming.patch Minor tweak to generic/hack-4.14/902-debloat_proc.patch to cleanly apply after upstream changes. Tested-on: ath79 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* wireguard: Update to snapshot 0.0.20181218Daniel Engberg2018-12-241-2/+2
| | | | | | Update WireGuard to 0.0.20181218 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* curl: bump to 7.63.0Deng Qingfang2018-12-242-4/+4
| | | | | | Refresh patches, for changes in version 7.63.0 see https://curl.haxx.se/changes.html#7_63_0 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ipq40xx: NBG6617: add usb-ledtrig-usbport to DEVICE_PACKAGESChristian Lamparter2018-12-221-1/+1
| | | | | | | | The ZyXEL NBG6617 USB LED was not working with the default images. It turned out that kmod-usb-ledtrig-usbport was missing from the default installation. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: switch MX60(W)'s recovery images to multi-image methodChristian Lamparter2018-12-221-25/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the past, the MX60(W)'s recovery images always had problems with the size restriction and never really worked without manual intervention. But starting with 4.19, the MX60(W)'s kernel image outgrew the allocated space for sysupgrade images as well. Hence This patch reworks the initramfs, which allows the device to ease up on the impossible tight kernel size requirements for the sysupgrade creation and packaging. And as a result, the now orphaned special ramdisk setup is removed in the process. This new initramfs can be loaded through the MX60(W) U-boot in the following way: => setenv bootargs console=ttyS0,$baudrate => tftpboot $meraki_loadaddr meraki_mx60-initramfs-kernel.bin [...] Load address: 0x800000 Loading: ################################################ [...] done [...] => bootm $fileaddr \## Booting kernel from Legacy Image at 00800000 ... ... Updated Flashing instructions for new installations which integrates the new recovery method. Users of existing installations that only want to sysupgrade don't need to update their existing u-boot env. => setenv owrt_load1 ubi read \${meraki_loadaddr} kernel => setenv owrt_load2 ubi read \${meraki_loadaddr} recovery => setenv lede_bootkernel bootm \${meraki_loadaddr_kernel} - \${meraki_loadaddr_fdt} => setenv owrt_bootkernel bootm \${meraki_loadaddr} => setenv owrt_bootargs setenv bootargs console=ttyS0,\${baudrate} rootfstype=squashfs mtdoops.mtddev=oops => setenv owrt_boot run meraki_ubi owrt_bootargs\; run owrt_load1 meraki_checkpart lede_bootkernel\; run owrt_load2 owrt_bootkernel => setenv bootcmd run owrt_boot => saveenv For more information and the latest flashing guide: please visit the OpenWrt Wiki Page for the MR60: <https://openwrt.org/toh/meraki/mx60#flashing> Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath9k: Avoid OF no-eeprom quirks when no qca,no-eepromDaniel F. Dickinson2018-12-221-0/+73
| | | | | | | | | | | | | | | | | | Based on the process of discovery in https://github.com/openwrt/openwrt/pull/1613, it has become clear that (at least) the PowerCloud System CR5000 was unable to get working 5GHz wireless (PCIe) because AH_USE_EEPROM was unconditionally masked out, not only when qca,noeeprom was in the DTS. This patch moves mask AH_USE_EEPROM into the if ... qca,noeeprom OF test. Thanks to Christian Lampartar (@chunkeey) for the heavy lifting and help. Patch has been prepared for upstream and will be submitted after review by @chunkeey and @xdarklight. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* odhcpd: use PKG_VERSION default valueHans Dedecker2018-12-211-2/+1
| | | | | | | Instrad of defining PKG_VERSION in the Makefile use the PKG_VERSION default value Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ipq40xx: disable kernel-padding for DNI imageDavid Bauer2018-12-201-3/+2
| | | | | | | | | | This commit removes the fixed kernel size-padding for the Netgear DNI image creation as it is not necessary for a working image. The fake rootfs still needs to be padded to the blocksize. Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix pcie wifi unit-address of the MR33 and A62Christian Lamparter2018-12-202-2/+2
| | | | | | | The unit address should be wifi@1,0 since the device is located at 0000:01:00.0. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* elfutils: fix gcc 8.0+ multistatement macros warning/errorChristian Lamparter2018-12-201-6/+8
| | | | | | | | | | | | | | | | | | | | | | GCC 8.0+ <https://gcc.gnu.org/gcc-8/changes.html> introduces a new warning about unsafe macros expanding to multiple statements used as a body of a statement such as if, else, while, switch, or for. In combination with -Werror this can cause the compilation to fail: |In file included from xmalloc.c:37: |xmalloc.c: In function 'xmalloc': |system.h:39:2: error: macro expands to multiple statements [-Werror=multistatement-macros] | fflush(stdout); \ | ^~~~~~ |xmalloc.c:52:5: note: in expansion of macro 'error' | error (EXIT_FAILURE, 0, _("memory exhausted")); | ^~~~~ |xmalloc.c:51:3: note: some parts of macro expansion are not guarded by this 'if' clause | if (p == NULL) | ^~ Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: Fix PowerCloud CR5000 5GHz wifi macDaniel F. Dickinson2018-12-201-3/+6
| | | | | | | | | | | | | | | | | | Without this patch PowerCloud CR5000 AR9382 PCIe 5GHz Wifi uses the mac address from eeprom instead the one specified when initializing the PCIe chip. There were two issues: 1) ap94_pci_init on the second PCIe wmac is wrong as there is only one PCIe wmac on this device (the other wmac is the AR1022/AR9342 SoC wmac). 2) Without specifying pdata->use_eeprom there is a failure to load firmware and caldata. Thanks to Christian Lamparter (@chunkeey) for the heavy lifting and help. [0] [0] <https://github.com/openwrt/openwrt/pull/1613> Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* odhcpd: add PKG_VERSION againHans Dedecker2018-12-201-0/+1
| | | | | | Fixes commit 63d0752ca8603886d8733ba888f49fc3b42c74fd Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* odhcpd: update to latest git HEADHans Dedecker2018-12-201-4/+3
| | | | | | | 2d2a3b8 odhcpd: switch to libubox container_of implementation 2a71c1e treewide: switch to libubox ARRAY_SIZE immplementation Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mac80211: backport upstream fixesKoen Vandeputte2018-12-202-0/+89
| | | | | | | d350a0f43118 nl80211: fix memory leak if validate_pae_over_nl80211() fails a50e5fb8db83 mac80211: fix a kernel panic when TXing after TXQ teardown Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mwlwifi: update to version 10.3.8.0-20181210Jo-Philipp Wich2018-12-201-3/+3
| | | | | | | | | | | | 67ce93e Fix compile error on kernel 4.15+ c1345bb Change driver version to 10.3.8.0-20181210. 9cb815b Upgrade 88W8997 firmware to 8.4.4.6. 433fc6d Fix non-backport use of nla_parse before 4.12.0 3b36e21 Use wiphy_to_ieee80211_hw() instead of wiphy_priv() 97ebcfa Change driver version to 10.3.8.0-20181120. f000953 Upgrade 88W8997 firmware to 8.4.4.4. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: drop MIPS fix cache flushing for highmem pagesKevin Darbyshire-Bryant2018-12-202-60/+0
| | | | | | | | | | | | | | | | | | | | | This patch, in a variety of forms, has been around since beginning 2016 as e756c2bb07, ending up in present form 0aa6c7df60 (kernel 4.4.13 bump) and carried forward ever since. There have been a number of MIPS kernel memory handling changes since, including VDSO fixes that meant openwrt patches have been dropped with no apparent fallout. Simple tests (ntfs-3g) on a HIGHMEM 512MB mt7621 device have not turned up data corruption issues which would otherwise be expected. Similarly running on other MIPS based devices for the past 2 months hasn't turned up anything obvious to retain this out of tree patch. With thanks to Rosen Penev for testing on the known 'highmem' device and Felix Fietkau for testing advice. Not putting acked-by as it's my fault if it breaks :-) Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath10k-firmware: update Candela Tech firmware imagesJo-Philipp Wich2018-12-201-22/+22
| | | | | | | - Removed an assert from wave-1 firmware images - Fix three recently reported firmware crashes in wave-2 images Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* iproute2: require nls infrastructure due to libelf linkingJo-Philipp Wich2018-12-201-1/+2
| | | | | | | | | | | Depending on the global nls support configuration in the buildroot, the linked libelf.so library might depend on libintl.so. Import the nls.mk helper to set library prefixes and flags accordingly in this case. Ref: https://github.com/openwrt/packages/issues/7728#issuecomment-448760140 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* elfutils: produce correct libelf.pc file when building with full nlsJo-Philipp Wich2018-12-202-3/+27
| | | | | | | | | | | When building with full lagnuage support, libelf.so will depend on and link with libintl.so so we need to change the pkg-config template to reflect this library dependency. Also change the Makefile to only pass --disable-nls to configure when the full nls support is actually disabled in the buildroot config. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: Update endian definitions for Mac OSXKevin Darbyshire-Bryant2018-12-191-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | - it appears (at least from OS X verison 10.10, Yosemite) that the big and little endian defintions have changed. the older #include <sys/_endian.h> #include <architecture/byte_order.h> reference yielded the following warning: #define __bswap_16(x) NXSwapShort(x) ^ /usr/include/architecture/byte_order.h:45:1: note: 'NXSwapShort' has been explicitly marked deprecated here For the new OS X editions, it seems that we need to refer to: #include <netinet/in.h> #include <libkern/OSByteOrder.h> and respectively use 'OSSwapInt16', 'OSSwapInt32', & 'OSSwapInt64', in place of 'NXSwapShort', 'NXSwapLong' & 'NXSwapLongLong'. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* scripts: rstrip.sh: allow rpath with sole $ORIGIN tokenYorkie Liu2018-12-191-1/+1
| | | | | | | | | | | | | | 2efe776 introduces rpath checks with the commit message: > Remove all rpath entries which do not point to a location below /lib or > /usr/lib and which do not begin with '$ORIGIN'. However the implementation failed to support rpath entries with only the '$ORIGIN' token and no trailing slash, so allow these as well. Signed-off-by: Yorkie Liu <yazhong.liu@rokid.com> [reword commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* iproute2: only link libelf where neededJo-Philipp Wich2018-12-192-2/+62
| | | | | | | | | | | | | | | | | | | | | The iproute2 build system links libelf support to every utility while only the tc program actually requires libelf specific functionality. Unfortunately the BPF ELF functionality is not confined into an own compilation unit but added to the existing bpf.c sources of the shared static libutil.a, causing every iproute2 applet to pick up an implicit libelf.so dependency. In order to avoid this requirement, patch the iproute2 build system to create both a libutil.a and a libutil-elf.a, with the former being built without libelf functionality and to only link the tc applet with the libelf enabled libutil. Finally, make the tc package depend on libelf to solve compilation errors. Ref: https://github.com/openwrt/packages/issues/7728 Fixes: FS#2011 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* elfutils: install library files for pkg-configTony Ambardar2018-12-191-0/+3
| | | | | | | Support other packages using pkg-config to query existence and details of libelf and libdw libraries at build time. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* base-files: install missing /etc/iproute2/ematch_mapTony Ambardar2018-12-191-0/+8
| | | | | | | | This file is needed to properly use the tc ematch modules present in kmod-sched-core and kmod-sched. It is a read-only index file of ematch methods used only by tc. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* brcm2708: switch to kernel 4.14Stijn Tintel2018-12-181-1/+1
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 14:37:03 +0000