aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* odhcpd: update to latest git HEADHans Dedecker2017-08-161-3/+3
| | | | | | | 94e65ee ndp: use IPv4 address list when comparing IPv4 addresses ff5020d dhcpv6-ia: rework reconfigure accept logic Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: add support for the VoCore2 LiteL. D. Pinney2017-08-119-51/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VoCore2 Lite uses the same PCB as the Vocore2. This patch moves the common VoCore2 parts into dtsi. Removed memory node in the device tree source file. Memory is detected automatically. http://vocore.io/ http://vonger.net/ http://vonger.cn/ Specifications: - SoC: MediaTek MT7688AN - RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H - Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG - Wireless: Built into MT7688AN with onboard IPEX connector Firmware installation: - VoCore2-Lite ships with firmware forked from OpenWrt. - Installation from the bootloader is recommended. - If using luci/sysupgrade use the -n option (do not keep settings) original firmware uses a modified proprietary MediaTek wireless driver. - The wireless is disabled by default in LEDE. - If reverting to factory firmware using the bootloader is recommended. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Tested by: Noble Pepper <noblepepper@gmail.com>
* ramips: fix WHR-1166D WAN portMathias Kresin2017-08-111-1/+1
| | | | | | | | | | | | By adding the ICPlus IP1001 phy driver an already set RGMII delay mode is reset during driver load. Set the rgmii rx delay to fix corrupt/no packages in case the WAN port negotiates to 1000MBit. Fixes: FS#670 Signed-off-by: Mathias Kresin <dev@kresin.me>
* wpa_supplicant: log to syslog instead of stdoutStijn Tintel2017-08-101-1/+1
| | | | | | | | While debugging an issue with a client device, wpa_supplicant did not seem to log anything at all. Make wpa_supplicant log to syslog instead of stdout, to make debugging easier and to be consistent with hostapd. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* brcm2708-gpu-fw: update to latest versionStijn Tintel2017-08-101-7/+7
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* base-files: drop unused preinit_echo functionRafał Miłecki2017-08-091-5/+0
| | | | | | It isn't used for years since the old 99_10_run_init has been dropped. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* nftables: remove date from versionHauke Mehrtens2017-08-091-1/+1
| | | | | | | We are using the normal 0.7 version of nftables, do not add an additional date to the version number. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tools/pkg-config: Update to 0.29.2Daniel Engberg2017-08-092-20/+2
| | | | | | | * Update pkg-config to 0.29.2 * Remove patch as it's upstreamed Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/expat: Update to 2.2.3Daniel Engberg2017-08-091-5/+2
| | | | | | | Update (lib)expat to 2.2.3 Remove poor entropy hack, 2.2.3 uses /dev/urandom in worst case Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* utils/e2fsprogs: Update to 1.43.5Daniel Engberg2017-08-091-2/+2
| | | | | | Update e2fsprogs to 1.43.5 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/e2fsprogs: Update to 1.43.5Daniel Engberg2017-08-091-2/+2
| | | | | | Update e2fsprogs to 1.43.5 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* lantiq: fix missing otg_cap on danube platformDaniel Gonzalez Cabanelas2017-08-092-29/+90
| | | | | | | | | | USB doesn't work in some danube boards because otg_cap is missing since previous changes made on the USB-dwc2 lantiq driver. Fix it. Tested on the ARV7518PW router. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* base-files: don't setup network in preinit if failsafe is disabledRafał Miłecki2017-08-091-1/+4
| | | | | | | | | | | | With failsafe disabled there is no point in early network setup. We don't send announcement over UDP and there is no way to ssh to the device. A side effect of this is avoiding a possibly incorrect network config (only with failsafe disabled). This problem is related to possible changes made by user in /etc/config/network. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* procd: update to the latest git HEADHans Dedecker2017-08-081-3/+3
| | | | | | a17e1e8 watchdog: fix inline watchdog_get_magicclose function prototype Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: ArcherC50v1: fix wlan2g MAC addressThibaut VARENE2017-08-061-0/+2
| | | | | | | | | | By default the wlan eprom contains the generic ralink MAC which is not the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses are decremented from the ethernet MAC. This patch fixes the MAC address for wlan2g in line with OFW. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* lantiq: board.d: use auto xfer_mode as defaultMartin Schiller2017-08-061-1/+3
| | | | | | | If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that ATM should be used for ADSL and PTM for VDSL. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ltq-vdsl-app: add support for auto xfer_mode and auto line_modeMartin Schiller2017-08-061-11/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that ATM should be used for ADSL and PTM for VDSL. xfer_mode and line_mode can be set to fixed value independantly from each other. The syntax for the tc_layer argument of vdsl_cpe_control is as follow: -T<TcADSL>:<TcCfgUsADSL>:<TcCfgDsADSL>_<TcVDSL>:<TcCfgUsVDSL>:<TcCfgDsVDSL> where TcADSL and TcVDSL can be: 1=ATM, 2=PTM/EFM, 4=Auto TC-Layer and TcCfgUsADSL, TcCfgUsVDSL, TcCfgDsADSL, TcCfgDsVDSL can be: 1=64/65-octet encapsulation supported 2=64/65-octet encapsulation with pre-emption 3=64/65-octet encapsulation with short packets Default: In case of no '-T' option is given, ADSL will be configured in ATM and VDSL in PTM/EFM: -T1:0x1:0x1_2:0x1:0x1 The '-M' argument of dsl_cpe_control defines the initial DSL mode (NextMode) for ADSL/VDSL multimode handling. Possible Values: 0=API-default, 1=ADSL, 2=VDSL Default: In case of no '-M' option is given, '0' (API-default) will be selected. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ltq-vdsl-app: mask out ADSL bits when VDSL is requestedMartin Schiller2017-08-061-1/+4
| | | | | | | If the line_mode is fixed configured to vdsl, than only G.993 VDSL should be used. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ltq-vdsl-app: use notification based ATM/PTM driver loadMartin Schiller2017-08-065-20/+34
| | | | | | | This patch removes the fixed atm/ptm driver loading and switches to notification based driver loading. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* lantiq: ltq-atm/ltq-ptm: fix showtime handling on driver loadMartin Schiller2017-08-063-8/+10
| | | | | | | | This is needed to be able to load the ltq-atm/ltq-ptm driver from a notify script during synchronization, because the line can reach showtime state before the driver is fully loaded. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* lantiq: split up dsl_notify.sh into separate notification handlersMartin Schiller2017-08-063-68/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This makes it possible to simply add additional notification handlers by putting new scripts in the /etc/hotplug.d/dsl directory. the following Environment Variables are used: (values marked with an * are only available when bonding support is compiled in) DSL_NOTIFICATION_TYPE with one of these values: - DSL_STATUS - DSL_INTERFACE_STATUS - DSL_DATARATE_STATUS_US - DSL_DATARATE_STATUS_DS DSL_LINE_NUMBER=<0|1> * If DSL_NOTIFICATION_TYPE == DSL_STATUS, these variables are set: - DSL_XTU_STATUS=<ADSL|VDSL> - DSL_TC_LAYER_STATUS=<ATM|EFM> - DSL_EFM_TC_CONFIG_US=<NORMAL|PRE_EMPTION> - DSL_EFM_TC_CONFIG_DS=<NORMAL> If DSL_NOTIFICATION_TYPE == DSL_INTERFACE_STATUS, these variables are set: - DSL_INTERFACE_STATUS=<DOWN|READY|HANDSHAKE|TRAINING|UP> - DSL_BONDING_STATUS=<INACTIVE|ACTIVE> * If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_US, these variables are set: - DSL_DATARATE_US_BC0=<Upstream data rate in bit/s for Channel 0> - DSL_DATARATE_US_BC1=<Upstream data rate in bit/s for Channel 1> * If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_DS, these variables are set: - DSL_DATARATE_DS_BC0=<Downstream data rate in bit/s for Channel 0> - DSL_DATARATE_DS_BC1=<Downstream data rate in bit/s for Channel 1> * Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ltq-xdsl-app: drop esi callMathias Kresin2017-08-063-4/+1
| | | | | | | | | | | | | The esi call was added to workaround a race condition between applying a configured mac address to the wan interface and starting the protocol (handler) as it was observed in a DHCP over ATM bridge configuration. Martin Schiller, TDT GmbH was so kind to test with their local infrastructure if the race condition still exists. The provided package dumps captured behind the DSLAM shows that it doesn't. It was most likely fixed with adding carrier support to the lantiq ptm/atm driver. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: add missing patchJohn Crispin2017-08-051-0/+27
| | | | | | This patch was accidentally dropped. Signed-off-by: John Crispin <john@phrozen.org>
* kernel: split patches folder up into backport, pending and hack foldersJohn Crispin2017-08-05747-2653/+3697
| | | | | | | | | | | | | | | | | | | | * properly format/comment all patches * merge debloat patches * merge Kconfig patches * merge swconfig patches * merge hotplug patches * drop 200-fix_localversion.patch - upstream * drop 222-arm_zimage_none.patch - unused * drop 252-mv_cesa_depends.patch - no longer required * drop 410-mtd-move-forward-declaration-of-struct-mtd_info.patch - unused * drop 661-fq_codel_keep_dropped_stats.patch - outdated * drop 702-phy_add_aneg_done_function.patch - upstream * drop 840-rtc7301.patch - unused * drop 841-rtc_pt7c4338.patch - upstream * drop 921-use_preinit_as_init.patch - unused * drop spio-gpio-old and gpio-mmc - unused Signed-off-by: John Crispin <john@phrozen.org>
* ramips: fix cd-poll sd card remove randomlyQin Wie2017-08-041-0/+4
| | | | | | | Fix when add 'mediatek,cd-poll' to dts cause the sd card be removed randomly. Special for the device without card-detect pin. Signed-off-by: Qin Wie <me@vonger.cn>
* base-files: suppress uci not found output in login.shFlorian Eckert2017-08-041-1/+1
| | | | | | | Fix "uci: Entry not found" output if "ttylogin" is not set in "etc/config/system" Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* odhcpd: update to latest git HEAD (FS#402, FS#524)Hans Dedecker2017-08-031-3/+3
| | | | | | | 296b4a0 dhcpv6: assign all viable DHCPv6 addresses by default (FS#402, FS#524) f4d38e0 treewide: reflect managed mode is related to RA Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: move common parts into dtsiMathias Kresin2017-08-0315-690/+379
| | | | | | | Move the common parts of boards with multiple flash size variants into dtsi files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: update device tree source filesL. D. Pinney2017-08-03212-1103/+1343
| | | | | | | | Use the GPIO dt-bindings macros and add compatible strings in the ramips device tree source files. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* tools/firmware-utils: document reserved fields in mkchkimgThibaut VARENE2017-08-031-4/+18
| | | | Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: Add support for Netgear EX3800Thibaut VARENE2017-08-033-5/+6
| | | | | | | | | | | | The Netgear EX3800 is essentially an EX3700 with a mains output socket. Both devices use the exact same firmware image (original firmware is named EX3700-EX3800-version.chk). This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and updating the necessary glue. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: EX3700: rename factory.bin to factory.chkThibaut VARENE2017-08-031-2/+2
| | | | | | | The stock firmware upgrade interface requires the file to end with a .chk extension. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: cleanup EX2700 and WN3000RPv3 LEDsThibaut VARENE2017-08-032-5/+4
| | | | | | | | | | | | | | | This patch cleans up the WN3000RPv3 and EX2700 setup, bringing it in line with other similar devices: The power led is a bicolor one. The bootloader brings the red side on at powerup. Instead of blinking the red side in diag.sh and need to forcefully turn it off in 01_leds, this patch simplifies the setup by relying on the default off state of the gpio-led driver for the red side and blinking the green side as with other devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: cleanup AsiaRF AWM002 eval board supportMathias Kresin2017-08-037-162/+130
| | | | | | | | | | | Cleanup the dtsi files and remove one layer of dtsi. Set the size of the firmware partition to a value matching the flash size from the board (variant) name. Remove the usb led trigger. There is neither a default config for the usb led trigger nor a LED for usb activity indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop AsiaRF AWM003 eval boardMathias Kresin2017-08-035-77/+1
| | | | | | | Everything is identical to the AWM002 8m eval board. No need to duplicate it once more. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Omnima MiniEMBWiFi imageMathias Kresin2017-08-031-0/+1
| | | | | | | Reference the Omnima MiniEMBWiFi device tree source file in the image build code. Otherwise the dts of the image processed before is used. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: build HuaWei HG255D imageMathias Kresin2017-08-031-0/+7
| | | | | | | The code to build an image was disabled some time ago for unknown reasons albeit the image looks fine. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop Edimax BR-6425 supportMathias Kresin2017-08-035-81/+0
| | | | | | Code to build an image for the Edimax BR-6425 never existed. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add missing partitionsMathias Kresin2017-08-032-9/+57
| | | | | | The partitions were lost during migration to device tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mediatek: move mt7623 support into a 32bit subtargetJohn Crispin2017-08-015-47/+58
| | | | | | this is in preparation for adding the new 64bit mt7622 support. Signed-off-by: John Crispin <john@phrozen.org>
* ramips: fix PCI init on MT7620 with Linux 4.9+Ilya Katsnelson2017-07-311-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So, this is kind of complicated. This has been upstream for a while, imported from OpenWRT/LEDE with some cleanups. LEDE ramips has stayed on linux-4.4 this whole time, with the old(er) version of the patch that had correct behavior[0], while upstream got changed[1]. When LEDE updated to kernel 4.9, the older version of the code from the patch got replaced with the upstream version containing the bug. The original behavior, however, seems to be correct here, as the official programming guide[2] indicates that bit 31 (PDRV_SW_SET) in register PPLL_CFG1 is reserved, but bit 23 (added as PPLL_LD) is the PPLL lock state (which also happens to line up with the error message). The original confusion probably comes from the double definition of PDRV_SW_SET[3, 4] in the upstream code, with one correct definition (31) and one incorrect one (23). I've also used the opportunity to clean up the error message a bit - it's still not really helpful to anyone who doesn't already know what the PPLL is, but at least it's slightly more readable now. This will probably need to be upstreamed as well, since with the way it's currently set up, it's unlikely PCI ever worked for anyone who's running an upstream kernel on that SoC. [0]: https://github.com/lede-project/source/blob/05d6e92594c507dcd1f4be6c1bcb2282fe1abe1f/target/linux/ramips/patches-4.4/0009-PCI-MIPS-adds-mt7620a-pcie-driver.patch#L259 [1]: https://github.com/torvalds/linux/blob/026d15f6b9878794fae1f794cae881ccd65052e5/arch/mips/pci/pci-mt7620.c#L246 [2]: http://www.anz.ru/files/mediatek/MT7620_ProgrammingGuide.pdf [3]: https://github.com/torvalds/linux/blob/026d15f6b9878794fae1f794cae881ccd65052e5/arch/mips/pci/pci-mt7620.c#L36 [4]: https://github.com/torvalds/linux/blob/026d15f6b9878794fae1f794cae881ccd65052e5/arch/mips/pci/pci-mt7620.c#L39 Signed-off-by: Ilya Katsnelson <me@0upti.me>
* procd: update to latest git HEADJohn Crispin2017-07-311-3/+3
| | | | | | f062b30 procd: Do not leak pipe file descriptors to children Signed-off-by: John Crispin <john@phrozen.org>
* fstools: update to latest git HEADJohn Crispin2017-07-311-3/+3
| | | | | | 8ab4fda fstools: add btrfs support Signed-off-by: John Crispin <john@phrozen.org>
* firmware-utils: mktplinkfw2: respect -e option when reading fw infoRafał Miłecki2017-07-311-3/+5
| | | | | | | | When -e option it specified a corresponding flag is set in the custom_board. By using custom_board as fallback -e option gets respected for unknown boards. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mktplinkfw2: fix info for images with LE kernel LA/EPRafał Miłecki2017-07-311-1/+7
| | | | | | | With this change endianness is also respected when reading firmware info. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mktplinkfw2: replace "endian_swap" field with "flags"Rafał Miłecki2017-07-311-8/+10
| | | | | | This will allow adding more similar tricks needed by other hardware. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: Archer C50v1: fix power ledThibaut VARENE2017-07-292-1/+1
| | | | | | | | | | 01_leds had a workaround for the power led to compensate for the inverted GPIO state. This patch was missing from my previous commit. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> [add the power led default-state which was omitted in the last commit by me] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Archer C50v1: fix switch port numberingThibaut VARENE2017-07-291-1/+4
| | | | | | | | Luci shows switch ports in wrong order on that device. This patch fixes switch port numbering and matches them to the device silkscreen. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: Archer C50v1: fix LEDs active levelsThibaut VARENE2017-07-291-2/+2
| | | | | | | | | | All LEDs GPIOs are active low on this device. WAN and POWER states were inverted. Add default state for power. Tested on Archer C50v1. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: fix Mercury MAC1200R v2.0 board nameMathias Kresin2017-07-292-1/+2
| | | | | | | | | | | | With d2b6bf141662 ("ramips: fix image validation errors") the board name was changed to fix an image validation error. But this change wasn't applied to all other files using the board name, which broke sysupgrade. Revert this change and use the former board name in the metadata instead. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-12 00:03:59 +0000