aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: use lzma-loader for Wevo devicesSeo Suchan2021-02-191-0/+2
| | | | | | | | | | | As kernel size increased it start to fail to load squishfs image, using lzma-loader fixed it. wevo_11acnas is almost same device as w2914ns-v2 except ram size, so I expect same thing would've happen in that device too. Signed-off-by: Seo Suchan <abnoeh@mail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit ca6954e2dc3faa32eec54b93bda996c874409675)
* ramips: mt7621: add TP-Link EAP235-Wall supportSander Vanheule2021-02-194-0/+225
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access point with four gigabit ethernet ports. When connecting to the device's serial port, it is strongly advised to use an isolated UART adapter. This prevents linking different power domains created by the PoE power supply, which may damage your devices. The device's U-Boot supports saving modified environments with `saveenv`. However, there is no u-boot-env partition, and saving modifications will cause the partition table to be overwritten. This is not an issue for running OpenWrt, but will prevent the vendor FW from functioning properly. Device specifications: * SoC: MT7621DAT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (MT7603EN): b/g/n, 2x2 * Wireless 5GHz (MT7613BEN): a/n/ac, 2x2 * Ethernet: 4× GbE * Back side: ETH0, PoE PD port * Bottom side: ETH1, ETH2, ETH3 * Single white device LED * LED button, reset button (available for failsafe) * PoE pass-through on port ETH3 (enabled with GPIO) Datasheet of the flash chip specifies a maximum frequency of 33MHz, but that didn't work. 20MHz gives no errors with reading (flash dump) or writing (sysupgrade). Device mac addresses: Stock firmware uses the same MAC address for ethernet (on device label) and 2.4GHz wireless. The 5GHz wireless address is incremented by one. This address is stored in the 'info' ('default-mac') partition at an offset of 8 bytes. From OEM ifconfig: eth a4:2b:b0:...:88 ra0 a4:2b:b0:...:88 rai0 a4:2b:b0:...:89 Flashing instructions: * Enable SSH in the web interface, and SSH into the target device * run `cliclientd stopcs`, this should return "success" * upload the factory image via the web interface Debricking: U-boot can be interrupted during boot, serial console is 57600 baud, 8n1 This allows installing a sysupgrade image, or fixing the device in another way. * Access serial header from the side of the board, close to ETH3, pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3. * Interrupt bootloader by holding '4' during boot, which drops the bootloader into its shell * Change default 'serverip' and 'ipaddr' variables (optional) * Download initramfs with `tftpboot`, and boot image with `bootm` # tftpboot 84000000 openwrt-initramfs.bin # bootm Revert to stock: Using the tplink-safeloader utility from the firmware-utils package, TP-Link's firmware image can be converted to an OpenWrt-compatible sysupgrade image: $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \ -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin This can then be flashed using the OpenWrt sysupgrade interface. The image will appear to be incompatible and must be force flashed, without keeping the current configuration. Known issues: - DFS support is incomplete (known issue with MT7613) - MT7613 radio may stop responding when idling, reboot required. This was an issue with the ddc75ff704 version of mt76, but appears to have improved/disappeared with bc3963764d. Error notice example: [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout Hardware was kindly provided for porting by Stijn Segers. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 1e75909a35a2b361cdfdfcf18a26ad61271b174e)
* ramips: remove factory image for TP-Link Archer C20 v1Stijn Segers2021-02-191-0/+1
| | | | | | | | | | | | | Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one tries to flash an OpenWrt factory image through the TP-Link web UI. The wiki page contains an explicit warning about this [1]. Disable the factory image altogether since it serves no purpose. [1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation Signed-off-by: Stijn Segers <foss@volatilesystems.org> (cherry picked from commit 0265cba40ad4f2b8ff4473ada123c35b53ffd97a)
* bcm63xx: update ethernet kernel panics fixÁlvaro Fernández Rojas2021-02-197-34/+54
| | | | | | | | Use new patch from Sieng Piaw Liew. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit 31a06f8fcc)
* cypress-firmware: fix PKG_SOURCE_URLÁlvaro Fernández Rojas2021-02-191-1/+1
| | | | | | | Download link has been moved. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit 7febba3e50)
* bcm27xx: add diag LEDsÁlvaro Fernández Rojas2021-02-191-0/+7
| | | | | | | | We can now use the power LED for diag in more devices thanks to the latest patches from the RPi foundation. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit 5bab472a11)
* bcm27xx: bcm2708: add missing RPi B DTS fileÁlvaro Fernández Rojas2021-02-191-1/+1
| | | | | | | | | RPI 1B DTS has been splitted into 2 files: - bcm2708-rpi-b.dts: Newest (rev2) RPI 1B - bcm2708-rpi-b-rev1.dts: Old (rev1) RPI 1B Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit 0aaa2cce1c)
* bcm27xx: add support for RPI CM4 and RPI 400Álvaro Fernández Rojas2021-02-192-6/+13
| | | | | | | Support added to bcm2709 (32 bits) and bcm2711 (64 bits). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit 8ad61118fd)
* bcm27xx-userland: update to latest versionÁlvaro Fernández Rojas2021-02-192-77/+2
| | | | | | | Adds some fixes and removes upstreamed patch. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit 1d3a9b1c00)
* bcm27xx-gpu-fw: update to latest versionÁlvaro Fernández Rojas2021-02-191-15/+15
| | | | | | | This is needed to add support for CM4 and RPI 400. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit f41e653da9)
* bcm27xx: import latest patches from the RPi foundationÁlvaro Fernández Rojas2021-02-19927-703/+41630
| | | | | | | | | | bcm2708: boot tested on RPi B+ v1.2 bcm2709: boot tested on RPi 3B v1.2 and RPi 4B v1.1 4G bcm2710: boot tested on RPi 3B v1.2 bcm2711: boot tested on RPi 4B v1.1 4G Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit f07e572f64)
* kernel: bump 5.4 to 5.4.99John Audia2021-02-1932-91/+89
| | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. No manual changes needed. Build system: x86_64 Build-tested: bcm27xx/bcm2711 Signed-off-by: John Audia <graysky@archlinux.us> (cherry-picked from commit 5d3a6fd970)
* build: fix ABI version for PROVIDES symbolsFelix Fietkau2021-02-181-1/+1
| | | | | | | | | GetABISuffix does not work for intra-package ABI version of provided symbols, since ABIV_$(provided) is not set. Fix ABI version by using $(ABIV_$(1)) directly Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 0db9d118657d)
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-186-2/+378
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 634c13c186646aff2badb51a43b248825d0fe5a0)
* mediatek: add Ubiquiti LED driverDavid Bauer2021-02-185-0/+242
| | | | | | | | | | | | Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED controller based on the Holtek HT32F52241 MCU. This driver is initially used by the Ubiquiti UniFi 6 LR, however judging from FCC pictures the MCU is also found on the U6-Mesh as well as the U6-Extender. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit c9137e2ddf97ede1db399dc38acff26feb48ba7e)
* lantiq: fritz7320: enable USB power supplyMathias Kresin2021-02-181-0/+46
| | | | | | | | | | | | | The USB ports if a FRIZZ!Box 7320 do not supply power to connected devices. Add the GPIOs enabling USB power as regulator, to enable USB power supply as soon as the USB driver is loaded. Fixes FS#3624 Signed-off-by: Mathias Kresin <dev@kresin.me> (cherry picked from commit 6e4e97b2256327bb380ee2a83da9a1ddf657e395)
* openssl: bump to 1.1.1jEneas U de Queiroz2021-02-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes 4 security vulnerabilities/bugs: - CVE-2021-2839 - SSLv2 vulnerability. Openssl 1.1.1 does not support SSLv2, but the affected functions still exist. Considered just a bug. - CVE-2021-2840 - calls EVP_CipherUpdate, EVP_EncryptUpdate and EVP_DecryptUpdate may overflow the output length argument in some cases where the input length is close to the maximum permissable length for an integer on the platform. In such cases the return value from the function call will be 1 (indicating success), but the output length value will be negative. - CVE-2021-2841 - The X509_issuer_and_serial_hash() function attempts to create a unique hash value based on the issuer and serial number data contained within an X509 certificate. However it was failing to correctly handle any errors that may occur while parsing the issuer field (which might occur if the issuer field is maliciously constructed). This may subsequently result in a NULL pointer deref and a crash leading to a potential denial of service attack. - Fixed SRP_Calc_client_key so that it runs in constant time. This could be exploited in a side channel attack to recover the password. The 3 CVEs above are currently awaiting analysis. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit 482c9ff289c65480c8e7340e1740db24c62f91df)
* kernel: 5.4: fix .patch file extensionAdrian Schmutzler2021-02-171-0/+0
| | | | | | | | File extension was truncated for pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 487b7ae5ebbbc76e0b2952658432d28eee07f7a2)
* ipq807x: drop targetAdrian Schmutzler2021-02-164-714/+0
| | | | | | This target is not ready for stable release yet. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: reorder more BuildPackages lines to deal with ABI_VERSIONFelix Fietkau2021-02-167-11/+13
| | | | | | | | After the ABI version rework, packages need to be declared in the order of their dependencies, so that dependent packages will use the right ABI version Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 75455b75a7ee)
* ath10k-ct: switch to 5.10Álvaro Fernández Rojas2021-02-167-103/+79
| | | | | | | | Let's switch to 5.10 now that mac80211 has been updated. Runtime-tested on ipq806x (Netgear R7800). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry-picked from commit a5c4c40476)
* OpenWrt v21.02: set branch defaultsAlexander Couzens2021-02-163-12/+8
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* util-linux: move libuuid BuildPackage line further up to fix ABI versioningFelix Fietkau2021-02-161-1/+3
| | | | | | | After the ABI version rework, packages need to be declared in the order of their dependencies, so that dependent packages will use the right ABI version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: fix getting ABI version for binary packages from the same source packageFelix Fietkau2021-02-151-1/+1
| | | | | | | We can't rely on the .version file being created yet, so use package variables to get it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: Update to version 5.10.16-1Hauke Mehrtens2021-02-1512-185/+19
| | | | | | The removed patches were applied upstream. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Refresh patches againHauke Mehrtens2021-02-1514-110/+124
| | | | | | | A wrong quilt configuration was used last time. Fixes: ed1e234d87fc ("mac80211: refresh patches") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm4908: fix GPIOs support by limiting them to 64Rafał Miłecki2021-02-151-0/+23
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: use DTS patches sent upstreamRafał Miłecki2021-02-155-33/+145
| | | | | | | | There are 2 new patches: 1. Netgear R8000P switch ports 2. Netgear R8000P LEDs Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* build: filter out own packages on package version checkFelix Fietkau2021-02-151-2/+2
| | | | | | | This was accidentally dropped in 27a4a71c2408 ("metadata: handle ABI version rebuild tracking for transient dependencies") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/fakeroot: fix build regression on macOSFelix Fietkau2021-02-151-0/+42
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: update to the latest version, set ABI_VERSION dynamicallyFelix Fietkau2021-02-151-6/+8
| | | | | | 2537be018587 cmake: add a possibility to set library version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: only overwrite ABI version for provided packages when base version ↵Felix Fietkau2021-02-151-5/+5
| | | | | | | | changed Should avoid some spurious rebuilds Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Mostly revert "build: add support for fixing up library soname"Felix Fietkau2021-02-154-84/+0
| | | | | | | | | This reverts commit b12288fa69b171f7c9405518c9bed3581a06f7ce. The patchelf approach is too fragile, and the only users of this have been converted to make patching unnecessary Leave the abi_version_str variable in place in rules.mk Signed-off-by: Felix Fietkau <nbd@nbd.name>
* wolfssl: use libtool patch for PKG_ABI_VERSIONFelix Fietkau2021-02-151-1/+1
| | | | | | Makes it unnecessary to patch .so files after build Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: add support for patching libtool to include ABI version in sonameFelix Fietkau2021-02-151-0/+10
| | | | | | Use the version from PKG_ABI_VERSION Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: use build system variable to specify ABI versionFelix Fietkau2021-02-151-4/+5
| | | | | | This removes the need to patch it afterwards Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm4908: add USB packages to the DEFAULT_PACKAGESRafał Miłecki2021-02-151-0/+2
| | | | | | | All known 41 BCM4908 devices have USB ports so it makes sense to include those packages by default. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: fix backport of PMB driverRafał Miłecki2021-02-151-0/+8
| | | | | | | Missing Makefile change was preventing kernel from actually compiling the driver. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: drop ofpart patch dropped from upstream mtd treeRafał Miłecki2021-02-156-236/+653
| | | | | | It stopped ofpart_parser_init() from being called Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport "ofpart" mtd parser upstream quirks supportRafał Miłecki2021-02-156-29/+77
| | | | | | | | | | This adds quirks support to the "ofpart" parser. It's required to support fixed partitions that require some extra logic. Right now only BCM4908 binding is supported (BCM4908 requires detecting currently used "firmware" partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: fix busy wait loop in mediatek PPE codeIlya Lipnitskiy2021-02-151-1/+1
| | | | | | | | | | | The intention is for the loop to timeout if the body does not succeed. The current logic calls time_is_before_jiffies(timeout) which is false until after the timeout, so the loop body never executes. time_is_after_jiffies(timeout) will return true until timeout is less than jiffies, which is the intended behavior here. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* wolfssl: use dynamic ABI_VERSION depending on the configuration and package ↵Felix Fietkau2021-02-151-1/+3
| | | | | | version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: use PKG_ABI_VERSIONFelix Fietkau2021-02-151-1/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* fakeroot: fix to work with glibc 2.33Ilya Lipnitskiy2021-02-151-0/+145
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following commit removed _STAT_VER definitions from glibc: https://sourceware.org/git/?p=glibc.git;a=commitdiff;h=8ed005daf0ab03e142500324a34087ce179ae78e That subsequently broke fakeroot: https://bugs.archlinux.org/task/69572 https://bugzilla.redhat.com/show_bug.cgi?id=1889862#c13 https://forum.openwrt.org/t/unable-to-build-toolchain-fakeroot-fails-perhaps-others-after-it/87966 Make the patch based on Jan Pazdziora's suggestion from here: https://lists.fedoraproject.org/archives/list/devel@lists.fedoraproject.org/message/SMQ3RYXEYTVZH6PLQMKNB3NM4XLPMNZO/ Add wrappers for newly exported symbols in glibc. Apply patch from Debian to fix warnings in fts_read and fts_children: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=676428 https://sources.debian.org/patches/fakeroot/1.25.3-1.1/eglibc-fts-without-LFS/ Fix __xmknod{,at} dev pointer argument. Switch default to assume * and not the absence of *. On glibc 2.33+, there is no definition for these functions in header files, so the compile test doesn't work. But, we can default to using the pointer (as is the case with newer glibc), and use the header file on older platforms to fail the test and use no pointer. Tested on my x86_64 Arch Linux machine, fakeroot unit tests pass. Also tested by building various .ipks and examining the tar contents, to ensure that the owner uid/gid was 0/0. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* tools/patchelf: bump to use latest masterIlya Lipnitskiy2021-02-151-4/+5
| | | | | | | | | | | | | | | | | | | Recent ABI_VERSION commits make use of patchelf. It was discovered that with patchelf 0.10(and even 0.12) various big endian targets fail to link against libubox SO that was processed through patchelf. Using latest master patchelf fixes those link errors. Potential commits affecting big-endian processing https://github.com/NixOS/patchelf/commit/884eccc4f061a3dbdbe63a4c73f1cc9bbf77fa7d https://github.com/NixOS/patchelf/commit/d148bae6c1291b93d660a156a1756670069cd8cc Recent builds with failures: http://buildbot.openwrt.org/master/images/builders/lantiq%2Fxrx200/builds/682 http://buildbot.openwrt.org/master/images/builders/ath79%2Fmikrotik/builds/449 Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* odhcpd: setup dhcpv4 server automagicallyDaniel Golle2021-02-152-6/+26
| | | | | | | | | | Automatically setup dhcpv4 server just like it's done for dhcpv6. To select whether odhcpd or dnsmasq are serving DHCPv4 requests there still is the 'maindhcp' option. To make things less confusing, make sure things really work out-of-the-box in case dnsmasq is not even installed at the time the uci-defaults script is being run. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Revert "wolfssl: use dynamic ABI_VERSION depending on the configuration and ↵Hauke Mehrtens2021-02-151-3/+1
| | | | | | | | | | | | | | | | package version" This fixes the build on MIPS BE like ath25 and ath79 target. We get this error message when linking libwolfssl: mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so when searching for -lwolfssl mips-openwrt-linux-musl/bin/ld: cannot find -lwolfssl collect2: error: ld returned 1 exit status This reverts commit 2591c83b3406c16d3c1cd2dc7fa59c3c1b901d3c. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "libubox: use PKG_ABI_VERSION"Hauke Mehrtens2021-02-151-4/+1
| | | | | | | | | | | | This fixes the build on MIPS BE like ath25 and ath79 target. We get this error message when linking libubox: mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so when searching for -lubox This reverts commit f421fefa8a34319c5ff5dcc1af39d6311ec1ad1e. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: mark toggle input on EX6150 as a switchKurt Roeckx2021-02-151-0/+1
| | | | | | | | | The Netgear EX6150 has an Access Point/Extender switch. Set it as an EV_SW. Otherwise when it's set to Access Point, it will trigger failsafe mode during boot. Fixes: FS#3590 Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
* Revert "imx6: bootscript-apalis: make it working on v2021.01 release"Petr Štetiar2021-02-141-4/+2
| | | | | | | | This reverts commit 4968fc8fb110612018af3ba2836be1b4744346e2 as the bump to v2021.01 needs swig on the host for pylibfdt which is needed by dtoc tool to generate .h/.c files from DTBs in SPL for mx6cuboxi_config. Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-27 13:20:30 +0000