aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery methodPetr Štetiar2018-11-261-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3735964 bytes Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and Nanostation M5 XW (ae6xe). 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for Ubiquity Bullet M (XW)Petr Štetiar2018-11-265-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix ethernet for f5d8235-v2 boardRoman Yeryomin2018-11-263-2/+14
| | | | | | | | | Belkin F5D8235 v2 has two ethernet switches on board. One internal rt3052 and rtl8366rb on rgmii interface. Looks like internal switch settings were lost in translation to device tree infrastructure. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ramips: add support for Skylab SKW92A in EVBRussell Senior2018-11-266-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifically, SKW92A_E16, described here: http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x u.FL - Power by micro-USB connector at USB1 on EVB - UART via micro-USB connector at USB3 on EVB (57600 8n1) - 5x Ethernet LEDs - 1x WLAN LEDs - 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next to daughter board on EVB - WPS/Reset button (S2 on EVB) - RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board Flash instruction: >From Skylab firmware: 1. Associate with SKYLAP_AP 2. In a browser, load: http://10.10.10.254/ 3. Username/password: admin/admin 4. In web admin interface: Administration / Upload Firmware, browse to sysupgrade image, apply, flash will fail with a message: Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data! 5. Telnet to 10.10.10.254, drops you into a root shell with no credentials 6. # cd /var 7. # mtd_write -r write tmpFW mtd4 Unlocking mtd4 ... Writing from tmpFW to mtd4 ... [e] 8. When flash has completed, you will have booted into your firmware. >From U-boot via TFTP and initramfs: 1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server 2. Connect to serial console at USB3 on EVB 3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "1" 7. At u-boot prompts: Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin 8. Move ethernet to port 0 (WAN) on EVB 9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash with sysupgrade. >From U-boot via TFTP direct flash: 1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server 2. Connect to serial console at USB3 on EVB (57600 8N1) 3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "2" 7. At u-boot prompts: Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin 8. When transfer is complete or as OpenWrt begins booting, move ethernet to port 0 (WAN). Signed-off-by: Russell Senior <russell@personaltelco.net>
* valgrind: enable LTO and refresh patchesSyrone Wong2018-11-263-2/+3
| | | | Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
* build: Introduce building of artifactsPetr Štetiar2018-11-261-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently could (ab)use IMAGES for this task, but the downside is, that the filenames has filesystem tied to the filename, which might be confusing as the artifact itself don't has to be used with that specific filesystem. Another downside is, that the artifacts built with IMAGES target are build for every FILESYSTEMS filesystem. Consider following use case: define Device/apalis ... FILESYSTEMS := ext4 squashfs IMAGES := spl-uboot.bin recovery.scr IMAGE/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot IMAGE/recovery.scr := recovery-scr endef Where we would get target binaries with following filenames: openwrt-imx6-apalis-squashfs.recovery.scr openwrt-imx6-apalis-squashfs.spl-uboot.bin openwrt-imx6-apalis-ext4.recovery.scr openwrt-imx6-apalis-ext4.spl-uboot.bin With proposed patch, we could now just do: define Device/apalis ... ARTIFACTS := spl-uboot.bin recovery.scr ARTIFACT/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot ARTIFACT/recovery.scr := recovery-scr endef Which would produce target binaries with following filenames: openwrt-imx6-apalis-recovery.scr openwrt-imx6-apalis-spl-uboot.bin Signed-off-by: Petr Štetiar <ynezz@true.cz> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* rb532: drop 4.9 supportRoman Yeryomin2018-11-2610-672/+0
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* rb532: switch to 4.14Roman Yeryomin2018-11-261-1/+1
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* rb532: add 4.14 supportRoman Yeryomin2018-11-2610-0/+672
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* nghttp2: bump to 1.35.0Hans Dedecker2018-11-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | e520469b Update manual pages 54067256 Bump up version number to 1.35.0 c4d2eeee Update AUTHORS f51e696e asio: Add stop() to listen_and_serve doc a433b132 Merge pull request #1260 from nghttp2/h2load-non-final-response cf48a56d Merge pull request #1238 from jktjkt/cmake-fix-libevent-detection 6cad1b24 nghttpx: Write mruby send_info early 3c393dca nghttpx: Fix assertion failure on mruby send_info with HTTP/1 frontend 17292445 h2load: Handle HTTP/1 non-final response f6644a92 make clang-format 48998f72 Merge pull request #1222 from donny-dont/fix/declspec 15ff52f9 Update README 6c03bb14 Upgrade travis toolchain 524b4392 Fix travis build failure 859bf2bc Update manual pages b5619fb1 h2load: Clarify that time for connect includes TLS handshake dcbe0c69 nghttpx: Simplify move ctor and operator 2996c284 nghttpx: Cleanup 42e8ceb6 nghttpx: Convert API status code to enum class 1daf9ce8 nghttpx: Convert WorkerEventType to enum class d68edf56 nghttpx: Convert MemcachedStatusCode to enum class 0c4e9fef nghttpx: Convert memcached op to enum class 571404c6 nghttpx: Convert MemcachedParseState to enum class 4d562b77 nghttpx: Convert LogFragmentType to enum class e6225871 nghttpx: Convert connection check status to enum class 4bd075de nghttpx: Convert Http2Session state to enum class b46a3249 nghttpx: Convert FreelistZone to enum class 4bd44b9c nghttpx: Convert dispatch state to enum class 1b42110d nghttpx: Make Downstream state enum class 0735ec55 nghttpx: Convert shrpx_connect_proto to enum class 00554779 nghttpx: Convert DNSResolverStatus to enum class 0963f389 nghttpx: Convert SerialEventType to enum class 1abfa3ca nghttpx: Make TLS handshake state enum class f2159bc2 nghttpx: Convert UpstreamAltMode to enum class b0eb68ee nghttpx: Convert shrpx_forwarded_node_type to enum class e7b7b037 nghttpx: Convert shrpx_cookie_secure to enum class 5e4f434f nghttpx: Convert shrpx_session_affinity to enum class 20ea964f nghttpx: Convert shrpx_proto to enum class d105619b src: Remove extra braces if possible ec5729b1 Use std::make_unique 6c919695 Use C++14 46576178 Don't send Transfer-Encoding to pre-HTTP/1.1 clients 5e925f87 Update doc 153531d4 nghttpx: Use the same type as standard stream operator<< f7287df0 Bump up version number to 1.35.0-DEV Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel/modules: TI ADS1015 kernel module support enabled.Roman Bazalevsky2018-11-251-0/+14
| | | | Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
* kernel/modules: ROHM BH1750 ALS IIO kernel module support enabled.Roman Bazalevsky2018-11-251-0/+13
| | | | Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
* mwlwifi: update to version 10.3.8.0-20181114Kabuli Chana2018-11-251-3/+3
| | | | | | compile / test target mvebu / mamba Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* lantiq/basefiles: use shutdown instead of stop when the system goes downMartin Schiller2018-11-251-1/+1
| | | | | | I can't see any reason why we shouldn't use shutdown for lantiq as well. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* base-files: sysupgrade: Allow downloading of firmware images using HTTPSPetr Štetiar2018-11-251-1/+2
| | | | | | Currently it's only possible to download images over HTTP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* flex: Add a lex symlinkRosen Penev2018-11-251-0/+5
| | | | | | | | | | Some packages like libpfring assume the presense of lex, which on some other systems is a symlink to flex but not all. Symlink flex to fix compilation. Arch Linux and Fedora do this as far as I know. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* imx6: image: ventana: Add missing BOOT_SCRIPT variablePetr Štetiar2018-11-251-0/+1
| | | | | | | | | | This is probably theoretical problem as the Ventana is defined first in the image Makefile, but once the position of the definition would change in the future (alphabetical sorting?) it would get bootscript from the previous board which would have BOOT_SCRIPT set. Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* strace: update to 4.25Syrone Wong2018-11-251-2/+2
| | | | Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
* ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3Daniel Golle2018-11-252-1/+2
| | | | | | | | | Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio which wasn't supported at the time the devices were added to OpenWrt. Now that we got it, include kmod-mt76x0e in images for those devices. Reported-by: Arian Sanusi <openwrt@semioptimal.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: enable CONFIG_BRIDGE_VLAN_FILTERINGDaniel Golle2018-11-252-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows us to use the bridge as a managed switch and gracefully handle mixed tagged and untagged frames. Prior to this, the only alternative was creating one bridge per vlan which quickly becomes a nightmare and still won't let you mix both tagged and untagged frames on the physical port without some complex ebtables magic. This is in line with the notion that OpenWRT is the network go-to swiss army knife when you need a nice set-and-forget, low maintenance box to handle a specific task. Current builds of the ip-bridge package already fully support this feature so the only requirement is enabling the kernel config. This is disabled by default so existing bridge configurations will not be affected. This patch only gives the ability to turn it on with an 'ip link' command. If there is interest, I could look into making the feature accessible via uci configuration. It causes about 3.1% hit on raw bridging speed, which is relatively trivial considering that I had to use 300 byte packets to strain the CPU enough to notice a slowdown at all. The ER8 would chug along at wire speed otherwise, and that's using only one core. Since the typical bridge use case on OpenWRT is wireless, I doubt it would be noticeable at all. With BRIDGE_VLAN_FILTERING iperf -u -c 192.168.1.105 -b 1G -l 300 ------------------------------------------------------------ Client connecting to 192.168.1.105, UDP port 5001 Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust) UDP buffer size: 208 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.12 port 58045 connected with 192.168.1.105 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec [ 3] Sent 3414986 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 811 MBytes 680 Mbits/sec 0.000 ms 581210/3414986 (0%) Without BRIDGE_VLAN_FILTERING iperf -u -c 192.168.1.105 -b 1G -l 300 ------------------------------------------------------------ Client connecting to 192.168.1.105, UDP port 5001 Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust) UDP buffer size: 208 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.12 port 36645 connected with 192.168.1.105 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec [ 3] Sent 3414990 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 836 MBytes 701 Mbits/sec 0.000 ms 493950/3414990 (0%) In terms of kernel size, it uses 16KB (6753K vs 6737K on ER8) so a 0.002% hit. The exact 16KB is probably just due to how the kernel is compressed. Suggested-by: Jonathan Thibault <jonathan@navigue.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uclient: update to latest Git headJo-Philipp Wich2018-11-241-3/+3
| | | | | | 3ba74eb uclient-http: properly handle HTTP redirects via proxy connections Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath79: specify "firmware" partition format for Ubiquiti UniFiRafał Miłecki2018-11-241-0/+1
| | | | | | | | | | | | This affects: 1. Ubiquiti UniFi-AC-LITE/LR 2. Ubiquiti UniFi-AC-PRO 3. Ubiquiti UniFi-AC-MESH 4. Ubiquiti UniFi-AC-MESH PRO Succesfully tested on UniFi AP AC Pro. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for WNDR3700 and v2Hannu Nyman2018-11-242-0/+2
| | | | | | | | Specify the new "firmware" partition format for Netgear WNDR3700 and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third device in the family. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: specify "firmware" partition format for TP-LINK Archer C7 v2Rafał Miłecki2018-11-241-1/+2
| | | | | | With this change it doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: drop unused arch_split_mtd_part()Rafał Miłecki2018-11-248-52/+18
| | | | | | | No single target/arch uses it and most likely there is no need to make such a potential code target/arch specific. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add missing version.h include to the TP-LINK parserRafał Miłecki2018-11-241-0/+1
| | | | | Fixes: a29c8d685be7 ("kernel: add DT binding support to the TP-LINK parser") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add DT binding support to the TP-LINK parserRafał Miłecki2018-11-241-0/+10
| | | | | | It allows triggering it directly by specifying format in the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for Netgear WNDR3800Rafał Miłecki2018-11-241-0/+1
| | | | | | It doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add DT binding support to the uimage parsersRafał Miłecki2018-11-241-0/+21
| | | | | | It allows specifying default and Netgear parsers directly in the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: don't auto-split "firmware" if it has "compatible" DT propertyRafał Miłecki2018-11-248-18/+20
| | | | | | | | | If "compatible" is being used that should trigger a proper parser directly. It's more reliable thanks to not trying parsers one by one. In such case partition shouldn't be split automatically to avoid parsing it twice. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: b53: register switch on probeDavid Bauer2018-11-231-22/+21
| | | | | | | | | | | | | Currently, the b53 MDIO switch driver registers the switch on config-init and not on device probe. Because of this, the switch gets added every time the associated interface comes up. This commit fixes this behavior by registering the switch on device probe. Compile- and run-tested on OCEDO Koala. Signed-off-by: David Bauer <mail@david-bauer.net>
* tools: tplink-safeloader: add C7v5 EU SupportListDavid Bauer2018-11-231-1/+5
| | | | | | | | | | Currently flash from WebIF is broken for Archer C7 v5 EU models as their SupportList entries are missing. The added entries originate from TP-Links latest Archer C7 v5 EU firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* procd: update to latest git HEADHans Dedecker2018-11-231-3/+3
| | | | | | d667354 early: set /tmp permissions explicitly Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* rpcd: update to latest Git headJo-Philipp Wich2018-11-221-2/+2
| | | | | | c79ef22 main: fix logic bug when not specifying a timeout option Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* rpcd: update to latest Git headJo-Philipp Wich2018-11-223-4/+10
| | | | | | | | | | 2cc4b99 file: use global exec timeout instead of own hardcoded limit ecd1660 exec: increase maximum execution time to 120s Also expose the socket and timeout options in /etc/config/rpcd for easier use. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* base-files: fix unkillable processes after restartLinus Kardell2018-11-221-0/+1
| | | | | | | | | | | | | | | When restart is run on an init script, the script traps SIGTERM. This is done as a workaround for scripts named the same name as the program they start. In that case, the init script process will have the same name as the program process, and so when the init script runs killall, it will kill itself. So SIGTERM is trapped to make the init script unkillable. However, the trap is retained when the init script runs start, and thus processes started by restart will not respond to SIGTERM, and will thus be unkillable unless you use SIGKILL. This fixes that by removing the trap before running start. Signed-off-by: Linus Kardell <linus@telliq.com>
* kernel: bump 3.18 to 3.18.126Koen Vandeputte2018-11-223-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested: adm5120 Runtime-tested: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.82Koen Vandeputte2018-11-225-8/+8
| | | | | | | | | | | Refreshed all patches. Compile-tested: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.9 to 4.9.138Koen Vandeputte2018-11-223-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested: ar71xx, layerscape Runtime-tested: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* bcm53xx: request Seama parser on DIR-885L directlyRafał Miłecki2018-11-222-1/+25
| | | | | | | | It's more reliable as mtd subsystem doesn't have to blindly try that parser. It allows disabling MTD_SPLIT_FIRMWARE completely (TRX is handled in a similar way). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add DT binding support to the Seama parserRafał Miłecki2018-11-221-0/+13
| | | | | | It allows specifying that parser directly in the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* glibc: update to latest 2.27 commitHans Dedecker2018-11-221-2/+2
| | | | | | | 1517dfb8aa Add an additional test to resolv/tst-resolv-network.c 1050634904 libanl: properly cleanup if first helper thread creation failed (bug 22927) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mt76: update to the latest versionFelix Fietkau2018-11-211-3/+3
| | | | | | | | | | | | 4734108 mt7603: use mt7603_wtbl_clear on station removal 9428e34 mt7603: fix watchdog reset sequence b3f82a3 mt7603: report PSE reset failures via debugfs a301dec mt7603: add back PSE client reset code 94cebfc mt7603: fix handling lost interrupt events during watchdog reset b38fe7d mt7603: only issue PSE reset on PSE stuck da666a7 mt7603: issue PSE reset if firmware debug register indicates stuck queues Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: update to the latest versionFelix Fietkau2018-11-201-4/+4
| | | | | | | | | | | | | | | | | 471d397 mt7603: fix priority for buffered multicast packets 3873e82 mt7603: fix MT_BMAP_0/MT_GROUP_THD_0 register initializion for mt7628 749d5c3 mt7603: fix reserved page handling for mt7628 d22799b mt7603: reduce reserved pages for beacons 42c5281 mt7603: fix maximum frame size in scheduler init fa7335b mt76: fix potential NULL pointer dereference in mt76_stop_tx_queues 84aa12a mt76: fix potential null pointer deref in mt76_sta_add 7c4c33c mt7603: skip efuse tx power data for mt7628 ca2c875 mt7603: add support for accessing remapped registers via ops b44d793 mt7603: clear PSE redirections before MCU init 82363ab mt7603: move tx status to rx queue 0 c09e8a4 mt7603: fix buffering of tx packets for powersave clients Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: move diff adding run_parsers_by_type() between mtd patchesRafał Miłecki2018-11-204-80/+80
| | | | | | | | It makes more sense to add run_parsers_by_type() in a patch that introduces parser types. That makes the other one just add a code using it. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: don't export parse_mtd_partitions_by_type() in 4.9 and 4.14Rafał Miłecki2018-11-2010-66/+56
| | | | | | That function isn't used anywhere out of the mtdpart.c & can be static. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* wireguard: bump to 0.0.20181119Jason A. Donenfeld2018-11-191-2/+2
| | | | | | | | | | | | | | | | | | | * chacha20,poly1305: fix up for win64 * poly1305: only export neon symbols when in use * poly1305: cleanup leftover debugging changes * crypto: resolve target prefix on buggy kernels * chacha20,poly1305: don't do compiler testing in generator and remove xor helper * crypto: better path resolution and more specific generated .S * poly1305: make frame pointers for auxiliary calls * chacha20,poly1305: do not use xlate This should fix up the various build errors, warnings, and insertion errors introduced by the previous snapshot, where we added some significant refactoring. In short, we're trying to port to using Andy Polyakov's original perlasm files, and this means quite a lot of work to re-do that had stableized in our old .S. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* kernel: drop mtd_pad_erasesize() helper from 4.9 and 4.14Rafał Miłecki2018-11-192-38/+2
| | | | | | | It has been last used in kernel 3.18 for uimage and squashfs splitters embedded in the mtdpart.c. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* netifd: update to latest git HEADHans Dedecker2018-11-191-3/+3
| | | | | | | | | 4b83102 treewide: switch to C-code style comments 70506bf treewide: make some functions static d9872db interface: fix removal of dynamic interfaces 2f7ef7d interface: rework code to get rid of interface_set_dynamic Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ar71xx: fix TP-Link Archer C7 v5 switch LEDsRinki Kumari2018-11-171-3/+15
| | | | Signed-off-by: Rinki Kumari <rinki13@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 17:46:12 +0000