aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: merge a few pending tx related fixesFelix Fietkau2021-04-043-0/+142
| | | | | | | Improve performance and fix potential mgmt tx hangs/warnings Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 571aedbc6cbb7a9bfc96bcad543a39d158925cbc)
* mac80211: backport upstream patches for driver disconnectFelix Fietkau2021-04-046-15/+593
| | | | | | | Needed for an mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 5dc501507222b38d731b89c3311d8253b73dd0e7)
* build: use -nostdinc and -isystem in NOSTDINC_FLAGS for out-of-tree kernel ↵Felix Fietkau2021-04-045-4/+11
| | | | | | | | | modules This resolves issues uncovered by musl updates Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 9ac47ee46918c45b91f4e4d1fa76b1e26b9d57fe)
* generic: add missing symbolsDavid Bauer2021-04-031-0/+1
| | | | | Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 55ed4bf6d7bf80b705d015c3b73f772db485ba9c)
* ath79: fix label_mac for NEC Aterm WG1200CRINAGAKI Hiroshi2021-04-021-2/+6
| | | | | | | | | | | On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label on the case, not LAN. This patch fixes this issue. Fixes: 50fdc0374b ("ath79: provide label MAC address") Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (cherry picked from commit e2331fb5491e52e3e21ab18b58d064b344e093e5)
* ramips: correct switch config of Youku yk1Shiji Yang2021-04-021-1/+4
| | | | | | | | | | | There are only two lan ports and one wan port on Youku yk1 Fixes: e9baf8265bb8 ("ramips: add support for Youku YK1") Signed-off-by: Shiji Yang <yangshiji66@qq.com> [add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit b88d2850c66d7dc937e570661a047c647c588af5)
* libunwind: Add MIPS64 dep checkDonald Hoskins2021-03-291-1/+1
| | | | | | | | | | | | libunwind dependency check does not allow for MIPS64 arch. Add MIPS64 awareness. libunwind seems to support MIPS64 without issues, it was limited by the dep arch check in the Makefile. Used to compile Suricata6/Rust locally without issue. Signed-off-by: Donald Hoskins <grommish@gmail.com> (cherry picked from commit ea6d4bdde20a3fecbfc44b99f53373e1d0666e34)
* ipq40xx: net: phy: qca807x: fix GPIO driverRobert Marko2021-03-291-0/+1
| | | | | | | | | | | | While rebasing into setting bits instead of magic values, I accidentally forgot to actually set the force bit. Without it using the pins as GPIO-s did not actually work. Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver") Signed-off-by: Robert Marko <robert.marko@sartura.hr> (cherry picked from commit 7f2d9ccd09a1d3034aaf9c943747fc1631da5cac)
* bpftools: fix libbpf pkgconfig fileTony Ambardar2021-03-291-0/+4
| | | | | | | | | | | | | | | | | | | | | | The pkgconfig file hardcodes a host library directory which cannot be overridden by OpenWrt during builds. Use SED to fix this and potential include directory problems, as is done with several other packages. This fixes a strange issue intermittently seen building iproute2 on the oxnas target: iptables modules directory: /usr/lib/iptables libc has setns: yes SELinux support: no libbpf support: no libbpf version 0.3.0 is too low, please update it to at least 0.1.0 LIBBPF_FORCE=on set, but couldn't find a usable libbpf Fixes: 2f0d672088c3 ("bpftools: add utility and library packages supporting eBPF usage") Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Tony Ambardar <itugrok@yahoo.com> (cherry picked from commit 9e64e4ce26719ea81637b0e3d9754bd5190f0c21)
* gitignore: add .vscode for VS Code usersÁlvaro Fernández Rojas2021-03-291-0/+1
| | | | | | | For Visual Studio Code users, .vscode is created inside the workspace. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit 12dbad1a86ebdbb4c9bd71b14eec245bc6373844)
* ath79: fix RS-485 on Teltonika RUT-955Daniel Golle2021-03-293-14/+6
| | | | | | | | | | DTR GPIO isn't actually needed and triggers boot warning. TX pin was off by one (GPIO 19 instead of GPIO 18). Reported-by: @tophirsch Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 53a7d5d614050a38a4e78f5a9e153e7612d587f0)
* lantiq: set maximum kernel size for ARV7519RW22Aleksander Jan Bajkowski2021-03-291-0/+2
| | | | | | | | | | | Some users report that current snapshot producies non-bootable images. Stock uboot can boot images if the kernel is smaller than 2MB. Set maximum kernel size and disable image building for this board. Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843 Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> (cherry picked from commit c027dbac5a5222e6be4706a7a6a0effefce8ae76)
* ppp: compile fix: unset FILTER variable in MakefileEike Ritter2021-03-291-0/+12
| | | | | | | | | | | | | | | | | If the environment variable FILTER is set before compilation, compilation of the ppp-package will fail with the error message Package ppp is missing dependencies for the following libraries: libpcap.so.1 The reason is that the OpenWrt-patch for the Makefile only comments out the line FILTER=y. Hence the pcap-library will be dynamically linked if the environment variable FILTER is set elsewhere, which causes compilation to fail. The fix consists on explicitly unsetting the variable FILTER instead. Signed-off-by: Eike Ritter <git@rittere.co.uk> (cherry picked from commit 46cd0765d0c585dc0b48c8c0a3f116ef83cd580f)
* busybox: udhcpc, allow zero length dhcp optionsRussell Senior2021-03-291-0/+49
| | | | | | | This patch skips zero length DHCP options instead of failing. Signed-off-by: Russell Senior <russell@personaltelco.net> (cherry picked from commit 1c0436507156dc136d9e2668507817395434109e)
* mvebu: Fix mac addresses for GL.iNet GL-MV1000Sven Eckelmann2021-03-291-0/+4
| | | | | | | | | | | | | | The original GL.iNet firmware has two different mac addresses in the factory/art partition. The first one is for the WAN interface only and the second one is for both lan0 and lan1. But the original submission for OpenWrt didn't initialize the mac addresses of the LAN ports for the DSA device at all. The ethernet mac address was then used for all DSA ports. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit c20ac84803242e5a6451184009dabc36ba83b96e)
* mvebu: Add button support for GL.iNet GL-MV1000Sven Eckelmann2021-03-291-0/+17
| | | | | | | | | | | | | | The original patch to support this device advertised support for the reset button and the "switch" in the commit message. But neither were actually integrated in the device tree or documented anywere. The button itself is now used to trigger a reset (as described in the official GL.iNet documentation). The switch itself is registered as BTN_0 like other devices from GL.iNet in ath79. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 01b911a9381426314762822f97e3a7e658295f50)
* mvebu: enable WRT1900AC v1 and WRT32X for buildbotsTad Davanzo2021-03-291-2/+0
| | | | | | | | Kernel size limits have been dealt with. Effective revert of a1eb2c46 and ac9730c4. Signed-off-by: Tad Davanzo <tad@spotco.us> (cherry picked from commit b4f76d9f0d61779b5e04228d1eb3f2ba412ffd26)
* mvebu: venom resize kernel to 6MBTad Davanzo2021-03-293-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | venom has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. venom uboot however as set from factory will load up to 6MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0x900000, size 0x600000 6291456 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "priKernSize"; priKernSize=0x0600000 Resize the root partitions from 120MB to 117MB to let kernel expand into it another 3MB. And set kernel target size to 6MB. Lastly set the kernel-size-migration compatibility version on venom to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us> (cherry picked from commit 15309f5133d55e92bec3ed91dfb3ac9d124f6a96)
* mvebu: mamba resize kernel to 4MBTad Davanzo2021-03-293-2/+55
| | | | | | | | | | | | | | | | | | | | | | | | | mamba has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. mamba uboot however as set from factory will load up to 4MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0xa00000, size 0x400000 4194304 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "pri_kern_size"; pri_kern_size=0x400000 Resize the root partitions from 37MB to 36MB to let kernel expand into it another 1MB. And set kernel target size to 4MB. Lastly add a compatibility version message: kernel-size-migration. And set it on mamba to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us> (cherry picked from commit 10415d5e7016b69dc71c5f1b03e8e17b586f8edd)
* firewall3: update to latest git HEADTony Ambardar2021-03-291-3/+3
| | | | | | | | | | | | | | | | This includes several improvements and fixes: 61db17e rules: fix device and chain usage for DSCP/MARK targets 7b844f4 zone: avoid duplicates in devices list c2c72c6 firewall3: remove last remaining sprintf() 12f6f14 iptables: fix serializing multiple weekdays 00f27ab firewall3: fix duplicate defaults section detection e8f2d8f ipsets: allow blank/commented lines with loadfile 8c2f9fa fw3: zones: limit zone names to 11 bytes 78d52a2 options: fix parsing of boolean attributes Signed-off-by: Tony Ambardar <itugrok@yahoo.com> (cherry picked from commit 0d75aa27d4093625c85f2d2233dd5392a7e2aa32)
* kernel: backports: mt7530: fix TRGMII mode after resetIlya Lipnitskiy2021-03-292-3/+87
| | | | | | | | | | | Backport upstream patch that fixes TRGMII mode now that mt7530 is actually resetting the switch on ramips devices. Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both. Fixes: 69551a244292 ("ramips: manage low reset lines") Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> (cherry picked from commit 680f91d0e5444d58815af03bf41c12592438f9d8)
* kernel: Deactivate CONFIG_VFIO in generic kernel configHauke Mehrtens2021-03-273-2/+1
| | | | | | | | | Instead of deactivating this in every target config, deactivate it once in the generic kernel config. I was asked for this config option in a x86 64 build in OpenWrt 21.02. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 7d6553c72edada262ada8dbe871243c35400573d)
* kernel: bump 5.4 to 5.4.108Hauke Mehrtens2021-03-2761-139/+132
| | | | | | | | | Refreshed all patches. Compile-tested on: x86_64, ath79, lantiq Runtime-tested on: x86_64, ath79 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: Add support for Buffalo WZR-HP-G300NHMauri Sandberg2021-03-276-5/+335
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is a wireless router working on 2.4GHz band based on Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103 wireless chip and Realtek RTL8366RB/S switches. Due to two different switches being used also two different devices are provided. Specification: - 400 MHz CPU - 64 MB of RAM - 32 MB of FLASH (NOR) - 3x3:2 2.4 GHz 802.11bgn - 5x 10/100/1000 Mbps Ethernet - 4x LED, 3x button, On/Off slider, Auto/On/Off slider - 1x USB 2.0 - bare UART header place on PCB Flash instruction: - NOTE: Pay attention to the switch variant and choose the image to flash accordingly. (dmesg / kernel logs can tell it) - Methods for flashing - Apply factory image in OEM firmware web-gui. - Sysupgrade on top of existing OpenWRT image - U-Boot TFPT recovery for both stock or OpenWRT images: The device U-boot contains a TFTP server that by default has an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot there is a time window, during which the device allows an image to be uploaded from a client with address 192.168.11.2. The image will be written on flash automatically. 1) Have a computer with static IP address 192.168.11.2 and the router device switched off. 2) Connect the LAN port next to the WAN port in the device and the computer using a network switch. 3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A arp -s 192.168.11.1 02:AA:BB:CC:DD:1A 4) Initiate an upload using TFTP image variant curl -T <imagename> tftp://192.168.11.1 5) Switch on the device. The image will be uploaded subsequently. You can keep an eye on the diag light on the device, it should keep on blinking for a while indicating the writing of the image. General notes: - In the stock firmware the MAC address is the same among all interfaces so it is left here that way too. Recovery: - TFTP method - U-boot serial console Differences to ar71xx platform - This device is split in two different targets now due to hardware being a bit different under the hood. Dynamic solution within the same image is left for later time. - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device cover, were the wrong way around and were renamed qos_on -> movie_off, qos_off -> movie_on. Associated key codes remained the same they were. The device tree source code is mostly based on musashino's work Signed-off-by: Mauri Sandberg <sandberg@mailfence.com> (cherry picked from commit bc356de2850f14629cb1301be719772fa1212e72)
* ath79: cfi: cmdset_0002: amd chip 0x2201 - write wordsMauri Sandberg2021-03-271-0/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | Generally, in upstream CFI flash memory driver uses buffers for write operations. That does not work with AMD chip with id 0x2201 and we must resort to writing word sized chunks only. That is, to not apply general buffer write functionality for this given chip. Without the patch kernel logs will be flooded with entries like below: MTD do_erase_oneblock(): ERASE 0x01fa0000 MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985) MTD do_erase_oneblock(): ERASE 0x01f80000 MTD do_write_buffer(): WRITE 0x01f80000(0x00001985) MTD do_write_buffer_wait(): software timeout, address:0x01f8000a. jffs2: Write clean marker to block at 0x01a60000 failed: -5 MTD do_erase_oneblock(): ERASE 0x01f60000 MTD do_write_buffer(): WRITE 0x01f60000(0x00001985) MTD do_write_buffer_wait(): software timeout, address:0x01f6000a. jffs2: Write clean marker to block at 0x01a40000 failed: -5 References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/ Signed-off-by: Mauri Sandberg <sandberg@mailfence.com> [added link to usptream fix submission] Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 8cc0fa8faceadac85353bb1a96e074518ef124e2)
* packages: kernel: add gpio-nxp-74hc153Mauri Sandberg2021-03-273-0/+327
| | | | | | | | | | | | | | | | | | | | | NXP 74HC153 is a GPIO expander. Its original source cide sits in ar71xx architecture tree. It has been slightly modified to get GPIO pin configuration from the device tree rather than a MACH file. Changes to the source file: - Remove struct nxp_74hc153_config - in nxp_74hc153_probe(), fetch GPIO configuration from device tree - allow GPIO framework decide the base number by passing -1 to it - remove support for kernel versions below 4.5.0 - add OF device compatibility string Create a package for inclusion in image. References: https://lore.kernel.org/linux-gpio/545111184.50061.1615922388276@ichabod.co-bxl/ Signed-off-by: Mauri Sandberg <sandberg@mailfence.com> [added link to driver usptreaming work in progress] Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 6a6f9e73dd65f9201bee911d2fae8595f86c093b)
* openssl: bump to 1.1.1kEneas U de Queiroz2021-03-272-24/+23
| | | | | | | | | | | | | This version fixes 2 security vulnerabilities, among other changes: - CVE-2021-3450: problem with verifying a certificate chain when using the X509_V_FLAG_X509_STRICT flag. - CVE-2021-3449: OpenSSL TLS server may crash if sent a maliciously crafted renegotiation ClientHello message from a client. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit 0bd0de7d43b3846ad0d7006294e1daaadfa7b532)
* build,json: backport default_packages fixesPaul Spooren2021-03-251-3/+3
| | | | | | | | | | | | Remove duplicate packages by running in `target/linux/` rather than `target/linux/<target>/<subtarget>` and sort packages alphabetically. Squash commit of: 7880a64848 build,json: 3rd fixup of default_packages b36068d35d build,json: fixup fixup of arch_packages 1bf2b3fe90 build,json: fixup missing arch_packages Signed-off-by: Paul Spooren <mail@aparcar.org>
* mwlwifi: add PKG_FLAGS:=nonsharedDaniel Golle2021-03-241-0/+1
| | | | | | | | | This should fix the problem of mwlwifi-firmware-* not being found when using the ImageBuilder. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 9b3aaf1cdb873cc2a7b2f2ef4e72ddb716afba38) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* build,json: fix duplicates in default_packagesPaul Spooren2021-03-231-1/+2
| | | | | | | | | | | | | | Calling without the DUMP=1 argument causes the target specific Makefile to be "included" again which adds the target specific packages twice, once on the actual run and once included from `include/target.mk`. This led to duplicate package entries, causing confusion in downstream projects using the generated JSON files. While at it, apply `black` style to Python script. Signed-off-by: Paul Spooren <mail@aparcar.org> (cherry picked from commit 7f4c2b1a4f9216218dced64794318f2197565c85)
* base-files: add logging for configuration importFlorian Eckert2021-03-221-0/+1
| | | | | | | Make sysupgrade backup import more verbose. Signed-off-by: Florian Eckert <fe@dev.tdt.de> (cherry picked from commit fdbdbe8eaaa6aa3acacdcb3ae1308b2a2055fc39)
* ramips: add support for ELECOM WRC-1750GST2INAGAKI Hiroshi2021-03-222-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB (NT5CC128M16JR-EK) - Flash : SPI-NOR 32 MiB (MX25L25645GMI-08G) - WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/Keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX, from ethernet port side - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-1750GST2 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC addresses: LAN : 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex)) WAN : 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex)) 2.4GHz : 04:AB:18:xx:xx:25 (Factory, 0x4 (hex)) 5GHz : 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (cherry picked from commit b3ca1f30efd7bb96a22f72b766d302e552265276)
* ath79: fix lan port display order for sitecom wlr-7100Walter Sonius2021-03-221-1/+1
| | | | | | | | | | | Physical port order watched from the back of the device is: 4 / 3 / 2 / 1 / WAN which also matches corresponding leds. This patch corrects LuCI switch webpage LAN port order. Signed-off-by: Walter Sonius <walterav1984@gmail.com> [improve commit title, fix sorting in 02_network] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 46c0634b508f731df487a7909c439b2794445e26)
* mvebu: add LED support for GL.iNet GL-MV1000Jeff Collins2021-03-222-1/+46
| | | | | | | | | This patch enables LED support for the GL.iNet GL-MV1000 Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com> [add SPDX identifier on new file, add aliases, minor cosmetic issues] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 6e0c780eb3b4ba1e52216c1d671897749dd81829)
* bcm27xx: bcm2711: correctly disable HW_RANDOM_BCM2835Álvaro Fernández Rojas2021-03-221-0/+1
| | | | | | | | | It was removed in bac74aff5e36, but it should have been disabled. More info: https://forum.openwrt.org/t/make-image-stops-at-random-number-generator-bcm27xx/91429/7 Fixes: bac74aff5e36 ("bcm27xx: bcm2711: disable HW_RANDOM_BCM2835") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit f93b544f01)
* uhttpd: update to git HEADHauke Mehrtens2021-03-211-4/+4
| | | | | | | 15346de client: Always close connection with request body in case of error Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 1170655f8b792b34f899350cb0272ad94bb2d3e2)
* uhttpd: Execute uci commit and reload_config onceHauke Mehrtens2021-03-211-4/+6
| | | | | | | | | Instead of doing uci commit and reload_config for each setting do it only once when one of these options was changed. This should make it a little faster when both conditions are taken. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 501221af542b5154fbf8788f8426bc7f5443764a)
* uhttpd: Reload config after uhttpd-mod-ubus was addedHauke Mehrtens2021-03-212-1/+3
| | | | | | | | | | | | | Without this change the config is only committed, but the uhttpd daemon is not reloaded. This reload is needed to apply the config. Without the reload of uhttpd, the ubus server is not available over http and returns a Error 404. This caused problems when installing luci on the snapshots and accessing it without reloading uhttpd. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit d25d281fd6686bda67636f6c1df918145b6cb738)
* mbedtls: update to 2.16.10Magnus Kroken2021-03-212-13/+13
| | | | | | | | | | | | | | | | | | | | This release of Mbed TLS provides bug fixes and minor enhancements. This release includes fixes for security issues. Security fixes: * Fix a buffer overflow in mbedtls_mpi_sub_abs() * Fix an errorneous estimation for an internal buffer in mbedtls_pk_write_key_pem() * Fix a stack buffer overflow with mbedtls_net_poll() and mbedtls_net_recv_timeout() * Guard against strong local side channel attack against base64 tables by making access aceess to them use constant flow code Full release announcement: https://github.com/ARMmbed/mbedtls/releases/tag/v2.16.10 Signed-off-by: Magnus Kroken <mkroken@gmail.com> (cherry picked from commit dbde2bcf60b5d5f54501a4b440f25fe7d02fbe5d)
* glibc: update to latest 2.33 commitHans Dedecker2021-03-211-2/+2
| | | | | | | | | | | | | db32fc27e7 test-container: Always copy test-specific support files [BZ #27537] 79c6be6a0a nptl: Remove private futex optimization [BZ #27304] f90d6b0484 pthread_once hangs when init routine throws an exception [BZ #18435] dd8023c2ac elf: ld.so --help calls _dl_init_paths without a main map [BZ #27577] ea5a537e87 elf: Always set l in _dl_init_paths (bug 23462) 64f6c287ad x86: Handle _SC_LEVEL1_ICACHE_LINESIZE [BZ #27444] 32b9280f1d io: Return EBAFD for negative file descriptor on fstat (BZ #27559) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (cherry picked from commit 956490ad6abead94c8b06e55b687074fa2fd5c62)
* archs38: Add CONFIG_HZ=100Hauke Mehrtens2021-03-191-0/+1
| | | | | | | | This kernel config option was missing and resulted in a question when building. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 047b7621bb3ac266d193cf110a468e42f844be4f)
* glibc: update to latest 2.33 commit (BZ #27462, BZ #27318, BZ #27389)Hans Dedecker2021-03-181-2/+2
| | | | | | | | | | | | | | a151f2e05a nscd: Fix double free in netgroupcache [BZ #27462] ee9f98d9ca x86: Set minimum x86-64 level marker [BZ #27318] 3e880d7337 nss: Re-enable NSS module loading after chroot [BZ #27389] 71b2463f61 x86: Add CPU-specific diagnostics to ld.so --list-diagnostics a1eb3915e7 x86: Automate generation of PREFERRED_FEATURE_INDEX_1 bitfield 33dc1dd602 ld.so: Implement the --list-diagnostics option 8d4241b897 string: Work around GCC PR 98512 in rawmemchr 6efa2d44c8 S390: Add new hwcap values. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (cherry picked from commit 0ef3c58ac83397dcc81ad739ffe09702bc7f58ff)
* bcm53xx: backport first 5.13 DTS changesRafał Miłecki2021-03-173-1/+476
| | | | | | | | This adds NVMEM bindings that are needed for proper booting on Linksys devices. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 98d456a14e00e24acec36247fb5bd379da90f84e)
* bcm47xx: make WGT634U NVRAM patch apply againRafał Miłecki2021-03-171-19/+9
| | | | | | Fixes: 1c48eee5b2bc ("kernel: backport Broadcom NVRAM driver cleanups") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 9530b9bb78845910de711d425f1e4b1c7d539b13)
* bcm53xx: initialize NVRAM from NVMEM driverRafał Miłecki2021-03-172-0/+92
| | | | | | | | | | | | NVRAM access may be needed early in boot process. Reading it using mtd happens quite late in the init process. Add NVRAM initialization to the NVMEM driver which comes up early and depends on IO mapping only. This is required by Linksys devices which use NVRAM content for proper partitioning (detecting current firmware partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit baf04eed028a838518c65be48cbaabe0892343aa)
* kernel: backport Broadcom NVRAM driver cleanupsRafał Miłecki2021-03-175-0/+357
| | | | | | | Refactoring of bcm47xx_nvram driver. It's used by bcm47xx and bcm53xx. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 1c48eee5b2bcfaf9815cc9a6f6664392d17164cb)
* bcm53xx: backport NVMEM NVRAM driverRafał Miłecki2021-03-173-0/+181
| | | | | | | | It supports NVRAM access described using DT binding. Right now NVRAM data is exposed using /sys/bus/nvmem/ only. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 01b1b375281b77233d65eb0ebda8e4e3a1bd2407)
* bcm53xx: backport more upstream dts stuff from kernel 5.11Rafał Miłecki2021-03-177-0/+507
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 8078d89a5357d13dc3f2e2055fd9d663c4f1bd04)
* bcm53xx: group dts backports by upstream kernel versionRafał Miłecki2021-03-174-1/+6
| | | | | | | It's a simple renaming thing. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit d0ee398c36983ccb2ee514e71f10d3c274546f17)
* bcm4908: backport recent bcm_sf2 changesRafał Miłecki2021-03-177-8/+265
| | | | | | | One 5.12 link fix and 5.13 crossbar support. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit e1b4fd52a8efe1dfcad4f4fbe59f1c35a09be0bd)
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 00:56:16 +0000