aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* libubox: bump to version 2019-02-27Yousong Zhou2019-03-011-4/+4
| | | | | | | | | | Contains the following change eeef7b5 blobmsg_json: blobmsg_format_string: do not escape '/' Resolves FS#2147 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* busybox: sync Config.in filesYousong Zhou2019-03-0125-825/+1225
| | | | | | | | | | | | | | The change was made with the following commands cd package/utils/busybox/config ../convert_menuconfig.pl ~/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/busybox-1.30.1 convert_defaults.pl has no changes other than overwriting defaults for BUSYBOX_DEFAULT_FEATURE_IPV6 Resolves FS#2146 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* busybox: unindent busybox Config.inYousong Zhou2019-03-0124-2267/+2267
| | | | | | | | | | | | | This is to align with upstream change 72089cf ("config: deindent all help texts") and to make the follow-up change syncing Config.in files with current busybox version more reviewable It was made with the following commands cd package/utils/busybox/config find . -name 'Config.in' | xargs sed -ir -e 's/^\t \([^ ]\)/\t\1/' Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ath79: Fix indentAdrian Schmutzler2019-03-011-1/+1
| | | | | | Fix wrong indentation introduced in 59c2f8a. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: rt2x00: cleanup ePA, RXIQ and TX-LOFT codeDaniel Golle2019-03-014-230/+84
| | | | | | | | | | consolidate patch 651-rt2x00-remove-unneccesary-code.patch. fixup the most obvious whitespace problems in RXIQ and TX-LOFT code. always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid compiler warning about them being potentially uninitialized. no functional changes (intended) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: rt2x00: patch tracking cosmeticsDaniel Golle2019-03-019-0/+27
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: remove uboot-oxnas-ox820 from default package selectionDaniel Golle2019-03-011-4/+0
| | | | | | | | All supported boards should work with the $vendor bootloader just fine. Existing users should mindfully re-flash using new initramfs build and restore $vendor bootloader's bootcmd to it's original setting. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: switch to kmod-ledtrig-usb-portDaniel Golle2019-03-015-7/+20
| | | | | | | | Add port handles for both USB 2.0 ports so they can be used as trigger-source for USB LEDs. Suggestions for pogoplug and akitio,mycloud devices are welcome. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: oxnas: sync with current oxnas/ox820 DTSDaniel Golle2019-03-011-5/+4
| | | | | | | | | Use tested values on shuttle,kd20 and assumed values for mitrastar,stg-212 and cloudengines,pogoplug*. akitio users have yet to report back stock flash layout to support vendor bootloader environment there as well. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: unify MTD partition namesDaniel Golle2019-03-014-8/+13
| | | | | | | Use 'u-boot' and 'u-boot-env' like the majority of OpenWrt targets does... Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* package/ncurses: change AR options to fix reproducible buildsAlexander Couzens2019-02-282-1/+23
| | | | | | | | | | ar has a deterministic (-D) and non-deterministic (-U) mode. OpenWrt is already using the deterministic mode by default, but ncurses' configure script force this to be non-deterministic. Since autoreconf fails to generate a new configure, the configure script is directly modified. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* include/kernel: sort autoload modules list to fix reproducible buildsAlexander Couzens2019-02-281-1/+1
| | | | | | | | When autoloading more than one modules per packages, /etc/modules.d/$module depends on the file system ordering. To test this: use disorderfs on the build_dir and build kmod-sched. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* oxnas: add missing NAND partitionsDaniel Golle2019-02-283-4/+68
| | | | | | | | | | | | | | | | add kernel and other missing NAND flash partitions to allow booting using stock loader instead of the 2nd-stage bootloader. This will ease installation from stock firmware on pogoplugs as well as stg212 aka. medion nas. Existing users of OpenWrt on those boards will have to boot initramfs generated after this commit and subsequently flash first the ubinized image, then again run initramfs to flash sysupgrade.tar image, and then restore bootcmd in U-Boot environment back to the original setting ('nboot 60500000 0 440000' or something like that) instead of jumping into the now no longer used 2nd-stage loader. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq806x: fix LED configuration for NEC Aterm WG2600HPINAGAKI Hiroshi2019-02-281-1/+1
| | | | | | | NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should be used as a portmask instead of "0x1e" for "WAN" LED configuration. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ar71xx: Change led trigger from usbdev to usbportDavid Santamaría Rogado2019-02-281-46/+46
| | | | | | | | | | | | | This patch changes all the legacy usbdev leds triggers to the use usbport. The problem is that the usbdev triggers get applied as usbport in sysfs but LuCI gets confused and is not able to show the configuration with usbdev. More information can be found in the PR: <https://github.com/openwrt/openwrt/pull/1819> Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [extended commit message]
* ath79: add support for TP-Link Archer C5 v1Bart Lauret2019-02-284-0/+58
| | | | | | | | | | | | | | | | | | | | TP-Link Archer C5 v1 is a dual band router based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: - 720 MHz CPU - 128 MB of RAM (Various chips) - 16 MB of FLASH (Various chips) - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi - minipcie slot with 3T3R 5 GHz QCA9880-BR4A - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch) - 10x LEDs, 2x software buttons For further informwation on the device, visit the wiki: <https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500> Signed-off-by: Bart Lauret <bblauret@gmail.com>
* ath79: TP-Link Archer C7 v4 swap usb port ledsDavid Santamaría Rogado2019-02-281-2/+2
| | | | | | | USB 1 triggers usb2 led and USB 2 triggers usb1. Lower LED is usb1 and upper LED usb2. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* ath79: Modify glinet x750 and AR300m MAC address offsetsLuo chongjun2019-02-282-2/+4
| | | | | | | | In the production of glinet, the MAC address of ethernet port is only written at the position where the ART area offset address is 0, and the MAC address of eth1 is added 1 on the basis of eth0. Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
* ipq40xx: add support for FritzBox 7530David Bauer2019-02-2812-7/+642
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* uboot-fritz4040: bump version to 2019-02-08David Bauer2019-02-281-5/+6
| | | | | | | Adds support for the AVM FRITZ!Box 7530. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
* scripts: make eva_ramboot.py offset configurableDavid Bauer2019-02-281-11/+19
| | | | | | | | | | | | The current eva_ramboot.py script is currently only compatible with Lantiq based AVM devices. For IPQ40xx devices, the offset needs to be changed. Also an alignment is not necessary here. Adjust the script to be able to pass an optional offset to load the image to. In case no offset is provided, the script behaves exactly as before this commit. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix pcie msi IRQ trigger levelChristian Lamparter2019-02-282-0/+64
| | | | | | | | | | | | | | | | | | From: Niklas Cassel <niklas.cassel@linaro.org> |The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level |triggered interrupt. | |The msi_ctrl_int will be high for as long as any MSI status bit is set, |thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the |IRQ handler to keep getting called, as long as any MSI status bit is set. |[...] |Not having the correct IRQ type defined will cause us to lose interrupts, |which in turn causes timeouts in the PCIe endpoint drivers. | |Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> |Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: enlarge PCIe BAR sizeChristian Lamparter2019-02-282-0/+87
| | | | | | | | | | | | | | | | | | | | | | | | | | David Bauer reported that the VDSL modem (attached via PCIe) on his AVM Fritz!Box 7530 was complaining about not having enough space in the BAR. A closer inspection of the old qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed: | qcom,pcie@80000 { | compatible = "qcom,msm_pcie"; | reg = <0x80000 0x2000>, | <0x99000 0x800>, | <0x40000000 0xf1d>, | <0x40000f20 0xa8>, | <0x40100000 0x1000>, | <0x40200000 0x100000>, | <0x40300000 0xd00000>; | reg-names = "parf", "phy", "dm_core", "elbi", | "conf", "io", "bars"; Matching the reg-names with the listed reg leads to <0xd00000> as the size for the "bars". BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html Reported-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: owl-loader: fix sparse endian warningsChristian Lamparter2019-02-281-5/+5
| | | | | | | | | | | | | owl-loader.c:83:21: sparse: warning: incorrect type in assignment (different base types) owl-loader.c:83:21: sparse: expected unsigned short [usertype] reg owl-loader.c:83:21: sparse: got restricted __be16 const [usertype] reg owl-loader.c:84:21: sparse: warning: incorrect type in assignment (different base types) owl-loader.c:84:21: sparse: expected unsigned int [usertype] val owl-loader.c:84:21: sparse: got restricted __be16 const [usertype] low_val owl-loader.c:85:28: sparse: warning: restricted __be16 degrades to integer Reported-by: kbuild test robot Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: disable touchscreen symbolsChristian Lamparter2019-02-282-6/+104
| | | | | | | | | | | This patch removes the obsolete touchscreen config symbols and all disables all remaining ones in the generic config. Generated by running drivers/input/touchscreen/Kconfig sed -n 's/^config[[:space:]]\(.*\)/# CONFIG_\1 is not set/p' Kconfig |\ sort -d Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: fix geode image buildsChristian Lamparter2019-02-282-0/+7
| | | | | | | | | | This patch adds the disabled DRM_RADEON and DRM_AMDGPU config symbols from the x86' config to the generic target configs. The existing symbols in the x86' configs are kept for now, until we know whenever we want to remove such symbols or not (see Github PR #1831, #1825, #1828). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Qxwlan E2600AC C1 and C2张鹏2019-02-2815-16/+980
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for COMFAST CF-E120A v3Roger Pueyo Centelles2019-02-283-0/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless CPE with two Ethernet ports and a 802.11an radio. Specifications: - AR9344 SoC - 535/400/267 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 5 GHz, up to 25 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add TP-Link TL-WR802N-v4 supportMarcel Jost2019-02-283-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N-v4. https://openwrt.org/toh/tp-link/tl-wr802n Specification: - MT7628N (580 MHz) - 64 MB RAM - 8 MB FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet - 1x LED Flash instruction: The only way to flash the image in TL-WR802N v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 10 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Marcel Jost <majo@icutech.ch>
* ramips: use generic board detection for Wavlink WL-WN575A3Thomas Vincent-Cross2019-02-284-17/+15
| | | | | | Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices. Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* ramips: various Wavlink WL-WN575A3 fixesThomas Vincent-Cross2019-02-281-4/+3
| | | | | | | | | * assign pinmux groups to gpio function for LEDs/buttons * rename flash node to be more generic in line with other device nodes * remove useless/incorrect eeprom property from wmac node * correct base mac address for embedded switch Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* wireguard: bump to 0.0.20190227Jason A. Donenfeld2019-02-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * wg-quick: freebsd: allow loopback to work FreeBSD adds a route for point-to-point destination addresses. We don't really want to specify any destination address, but unfortunately we have to. Before we tried to cheat by giving our own address as the destination, but this had the unfortunate effect of preventing loopback from working on our local ip address. We work around this with yet another kludge: we set the destination address to 127.0.0.1. Since 127.0.0.1 is already assigned to an interface, this has the same effect of not specifying a destination address, and therefore we accomplish the intended behavior. Note that the bad behavior is still present in Darwin, where such workaround does not exist. * tools: remove unused check phony declaration * highlighter: when subtracting char, cast to unsigned * chacha20: name enums * tools: fight compiler slightly harder * tools: c_acc doesn't need to be initialized * queueing: more reasonable allocator function convention Usual nits. * systemd: wg-quick should depend on nss-lookup.target Since wg-quick(8) calls wg(8) which does hostname lookups, we should probably only run this after we're allowed to look up hostnames. * compat: backport ALIGN_DOWN * noise: whiten the nanoseconds portion of the timestamp This mitigates unrelated sidechannel attacks that think they can turn WireGuard into a useful time oracle. * hashtables: decouple hashtable allocations from the main device allocation The hashtable allocations are quite large, and cause the device allocation in the net framework to stall sometimes while it tries to find a contiguous region that can fit the device struct. To fix the allocation stalls, decouple the hashtable allocations from the device allocation and allocate the hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall back to vmalloc with little resistance. * chacha20poly1305: permit unaligned strides on certain platforms The map allocations required to fix this are mostly slower than unaligned paths. * noise: store clamped key instead of raw key This causes `wg show` to now show the right thing. Useful for doing comparisons. * compat: ipv6_stub is sometimes null On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has been disabled with a command line flag or other failures. * Makefile: don't duplicate code in install and modules-install * Makefile: make the depmod path configurable * queueing: net-next has changed signature of skb_probe_transport_header A 5.1 change. This could change again, but for now it allows us to keep this snapshot aligned with our upstream submissions. * netlink: don't remove allowed ips for new peers * peer: only synchronize_rcu_bh and traverse trie once when removing all peers * allowedips: maintain per-peer list of allowedips This is a rather big and important change that makes it much much faster to do operations involving thousands of peers. Batch peer/allowedip addition and clearing is several orders of magnitude faster now. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* tools: migrate from squashfs4 to squashfskit4Alexander Couzens2019-02-2813-1408/+9
| | | | | | | | | squashfskit is a fork of the squashfs-tools. squashfskit creates reproducible filesystems and includes many of the distro patches. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Tested-by: Paul Spooren <mail@aparcar.org>
* openssl: bump to release 1.1.1bEneas U de Queiroz2019-02-279-643/+5
| | | | | | | | | | | This is bugfix release that incorporated all of the devcrypto engine patches currently in the tree. The cleaning procedure in Package/Configure was not removing the dependency files, causing linking errors during a rebuild with different options. It was replaced by a simple make clean. Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
* odhcpd: update to latest git HEADHans Dedecker2019-02-271-3/+3
| | | | | | 16c5b6c ubus: always trigger an update if interface is not found Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* omcproxy: define configuration fileDavid Santamaría Rogado2019-02-271-1/+5
| | | | | | | omcproxy's configuration is lost on every update or installation. Avoid it by defining the configuration file. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* Revert "iw: compile with LTO enabled"Mantas Pucka2019-02-261-3/+2
| | | | | | | | | | | | | After update to 5.0.1 iw-full package failed to display command list on ipq40xx arch. Root cause was found to be LTO reordering causing incorrect detection of command struct size in: iw.c:552 cmd_size = labs((long)&__section_set - (long)&__section_get); This reverts commit ef16a394d2b24a363b50b5b4720cb23fe156c9da. Signed-off-by: Mantas Pucka <mantas@8devices.com>
* strace: update to version 2.26Hauke Mehrtens2019-02-263-3/+94
| | | | | | The new patch is a backport from current strace master. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tools/isl: update to 0.20Syrone Wong2019-02-261-2/+2
| | | | Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
* toolchain/binutils: Add binutils 2.32Daniel Engberg2019-02-267-0/+110
| | | | | | Add binutils 2.32 to repo Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* toolchain: Update to GCC 8.3.0Daniel Engberg2019-02-2622-7/+6
| | | | | | | | | Update GCC to 8.3.0 Refresh patches Allow GCC to be used for ARC Source: https://github.com/openwrt/openwrt/pull/1803#issuecomment-462334890 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* toolchain/gcc: Remove workaround for GCC 4.8Daniel Engberg2019-02-261-5/+2
| | | | | | GCC 4.8 was removed a long time ago... Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* popt: Use modern toolchain logicDaniel Engberg2019-02-261-6/+1
| | | | | | Replace define Build/Configure with CONFIGURE_ARGS Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* elfutils: fix install .so globMatt Merhar2019-02-261-3/+3
| | | | | | | Only libelf was being packaged correctly - libdw and libasm included just the symlinks. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* sunxi: add support for Orange Pi OneAleksander Jan Bajkowski2019-02-262-0/+17
| | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 512MB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard header: SPI, I2C, GPIO, UART USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ath79: fix support-list for TP-Link WDR3600David Bauer2019-02-261-1/+1
| | | | | | | | | | | | The TP-Link WDR3600 shares the same machine-code in the ar71xx target, thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list metadata to allow non-forced sysupgrades from ar71xx to ath79. With this, it is possible to flash a WDR4300 image on the WDR3600. It is no problem however, as the only difference is the 5GHz WiFi chip which has 3SS instead of 2SS. Both work with either image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add ar71xx support-list entry for Fritz4020David Bauer2019-02-261-0/+1
| | | | | | | This adds the support-list entry the AVM FRITZ!Box 4020 expects in the ar71xx target to allow non-forced sysupgrades from ar71xx to ath79. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: GL.iNet AR300M family: correct LED definitionsAndreas Ziegler2019-02-262-8/+2
| | | | | | | | remove USB as this is no LED but power control rename WiFi LED with correct color red (like in stock firmware) set middle LED to be used for LAN link/activity Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
* ath10k-ct: fix incorrect multicast/broadcast rate settingSven Eckelmann2019-02-264-2/+82
| | | | | | | | | | | | | | | | | If no mcast_rate is set for the wifi-iface then there is no rate_idx (0) set for the bss. This can break for example 5GHz meshpoint interfaces because 0 maps to a CCK rate (11Mbit/s). It must also be avoided that the ath10k-ct internal state for the rates is not synced with the mac80211 rates state. Otherwise, the user specified rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be set on startup. And a short while after that, ath10k-ct specific code in ath10k_check_apply_special_rates is missing a valid rate in its own structures and is then recalculating a new default rate. This default rate is in most situations not the requested rate. Fixes: 4df3c71cd4c5 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* mac80211: ath10k: fix incorrect multicast/broadcast rate settingSven Eckelmann2019-02-262-1/+44
| | | | | | | | | If no mcast_rate is set for the wifi-iface then there is no rate_idx (0) set for the bss. This breaks for example 5GHz meshpoint interfaces because 0 maps to a CCK rate (11Mbit/s). Fixes: db90c243a0b9 ("mac80211: update to version based on 4.19-rc4") Signed-off-by: Sven Eckelmann <sven@narfation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 17:18:04 +0000