aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: ubnt-xm: hijack LED4 as booting/failsafeLech Perczak2018-08-231-1/+6
| | | | | | | | | | Create aliases for led-booting and led-failsafe pointing at ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback on device status becomes available, in order to enter failsafe mode via button. led-running and led-upgrade aliases are omitted to avoid conflicting with RSSI LEDs when in normal operation. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: disable WAN on (rocket|bullet)-mLech Perczak2018-08-231-0/+2
| | | | | | | | | | | ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet port, therefore disable creation of WAN zone and interfaces for them, as their intended purpose is a wireless bridge. This aligns the configuration with one found in ar71xx target. ubnt,nano-m target is kept as is, being a two-port device. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: support ath9k firmware loadingLech Perczak2018-08-231-0/+5
| | | | | | | | Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards. This is required for wireless interface to function. Runtime tested on Nanobridge M5. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for I-O DATA ETG3-RINAGAKI Hiroshi2018-08-233-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA ETG3-R is a wired router, based on Atheros AR9342. Specification: - Atheros AR9342 - 64 MB of RAM - 8 MB of Flash - 5x 10/100/1000 Ethernet - AR8327N - 2x LEDs, 1x key - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using initramfs image: 1. Connect serial cable to UART header on ETG3-R 2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in the TFTP directory 3. Set IP address of the computer to 192.168.0.10, connect to the LAN port of ETG3-R, and start the TFTP server on the computer 4. Connect power cable to ETG3-R and turn on the router 5. Press "Enter" key when the "Hit any key to stop autoboot:" message is displayed on the console and enter the u-boot cli 6. execute following commands to change kernel address for u-boot setenv bootsf 1 setenv mtd_kernel1 "bootm 0x9f050000" saveenv 7. execute "tftpboot; bootm" command to download the initramfs image from TFTP server and boot with it 8. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for ETG3-R 9. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7620: add dir-810l network configRoger Pueyo Centelles2018-08-231-0/+1
| | | | | | | The device was not included in the /etc/board.d/02_network file, so the network wouldn't be properly set up on boot. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for ELECOM WRC-1900GSTNOGUCHI Hiroshi2018-08-236-172/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A. This is almost same as WRC-2533GST except wireless specs. Specifications: - SoC : MT7621A (four logical CPU cores) - RAM : 128MiB - ROM : 16MiB of SPI NOR-FLASH - wireless : 5GHz : 3T3R up to 1300Mbps/11ac with MT7615 2.4GHz : 3T3R up to 600Mbps/11n with MT7615 - Ethernet : 5 ports, all ports is capable of 1000base-T - Ether switch : MT7530 (MT7621A built-in) - LEDs : 4 LEDs - buttons : 2 buttons and 1 slide-switch - UART : header is on PCB, 57600bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-1900GST 2. Connect power cable to WRC-1900GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* ramips: fix compatibles in SoC dtsiMathias Kresin2018-08-233-3/+3
| | | | | | | The former used compatibles aren't defined anywhere and aren't used by the devicetree source files including them. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix GL-MT300N-V2 SoC compatibleMathias Kresin2018-08-231-1/+1
| | | | | | | | According to abbfcc85259a ("ramips: add support for GL-inet GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC compatible to match the used hardware. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop not existing groups from pinmuxMathias Kresin2018-08-2310-10/+10
| | | | | | | | | | | | | | RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't have a jtag group. Having these groups defined might cause a boot panic. The pin controller fails to initialise for kernels > 4.9 if invalid groups are used. If a subsystem references a pin controller configuration node, it can not find this node and errors out. In worst case it's the SPI driver which errors out and we have no root filesystem to mount. Signed-off-by: Mathias Kresin <dev@kresin.me>
* generic: revert workarounds for AR8337 switchMathias Kresin2018-08-232-62/+1
| | | | | | | | | | | | | The intention of 967b6be118e3 ("ar8327: Add workarounds for AR8337 switch") was to remove the register fixups for AR8337. But instead they were removed for AR8327. The RGMII RX delay is forced even if the port is used as phy instead of mac, which results in no package flow at least for one board. Fixes: FS#1664 Signed-off-by: Mathias Kresin <dev@kresin.me>
* wolfssl: disable broken shipped Job server macroJo-Philipp Wich2018-08-231-0/+21
| | | | | | | | | | | | | | | | The AX_AM_JOBSERVER macro shipped with m4/ax_am_jobserver.m4 is broken on plain POSIX shells due to the use of `let`. Shells lacking `let` will fail to run the generated m4sh code and end up invoking "make" with "-jyes" as argument, fialing the build. Since there is no reason in the first place for some random package to muck with the make job server settings and since we do not want it to randomly override "-j" either, simply remove references to this defunct macro to let the build succeed on platforms which not happen to use bash as default shell. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* grub2: rebase patchesJo-Philipp Wich2018-08-231-8/+4
| | | | | | | | | Patch 300-CVE-2015-8370.patch was added without proper rebasing on the version used by OpenWrt, make it apply and refresh the patch to fix compilation. Fixes: 7e73e9128f ("grub2: Fix CVE-2015-8370") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uhttpd: support multiple Lua prefixesJo-Philipp Wich2018-08-233-21/+32
| | | | | | | | | | | | | | | | | | | Update to latest git HEAD in order to support configuring multiple concurrent Lua prefixes in a single uhttpd instance: b741dec lua: support multiple Lua prefixes Additionally rework the init script and update the default configuration example to treat the lua_prefix option as key=value uci list, similar to the interpreter extension mapping. Support for the old "option lua_prefix" plus "option lua_handler" notation is still present. Finally drop the sed postinstall hack in uhttpd-mod-lua to avoid mangling files belonging to other packages. Since Lua prefixes have precedence over CGI prefixes, simply register `/cgi-bin/luci` as Lua handler which will only become active if both luci-base and uhttpd-mod-lua is installed. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* grub2: Fix CVE-2015-8370Rosen Penev2018-08-232-1/+45
| | | | | | | | | | | This CVE is a culmination of multiple integer overflow issues that cause multiple issues like Denial of Service and authentication bypass. More info: https://nvd.nist.gov/vuln/detail/CVE-2015-8370 Taken from Fedora. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* bzip2: Fix CVE-2016-3189Rosen Penev2018-08-232-1/+12
| | | | | | | | | | Issue causes a crash with specially crafted bzip2 files. More info: https://nvd.nist.gov/vuln/detail/CVE-2016-3189 Taken from Fedora. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: bump 4.14 to 4.14.66Koen Vandeputte2018-08-2247-370/+232
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.123Koen Vandeputte2018-08-224-19/+19
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix build error due to bad includeKoen Vandeputte2018-08-224-5/+20
| | | | | | | | | | | | | | | | | | While "rawnand.h" is available in kernel 4.14, the default for this target is kernel 4.9 in which "nand.h" should be used. Add an extra check to include the correct file depending on kernel version Fixes these build errors: drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory #include <linux/mtd/rawnand.h> ^~~~~~~~~~~~~~~~~~~~~ compilation terminated. Fixes: 318e19ba6755 ("ar71xx: add v4.14 support") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: add missing include for checking kernel versionKoen Vandeputte2018-08-2210-0/+10
| | | | | | | | | | | | | | | | | | Fixes these build errors: arch/mips/ath79/mach-rb2011.c:20:5: error: "LINUX_VERSION_CODE" is not defined, evaluates to 0 [-Werror=undef] #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^~~~~~~~~~~~~~~~~~ arch/mips/ath79/mach-rb2011.c:20:26: error: "KERNEL_VERSION" is not defined, evaluates to 0 [-Werror=undef] #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^~~~~~~~~~~~~~ arch/mips/ath79/mach-rb2011.c:20:40: error: missing binary operator before token "(" #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^ Fixes: 318e19ba6755 ("ar71xx: add v4.14 support") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* samba36: Enable umdnsd supportRosen Penev2018-08-222-1/+2
| | | | | | | | | | Allows discovery without having to use NetBIOS. Useful for mobile devices. Could eventually throw nbmd away. But that requires Windows 10... Tested on Fedora 28 with avahi-discover. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* yamonenv: Remove dead URLsRosen Penev2018-08-221-2/+1
| | | | | | uscan errors on the URL as it is no longer available. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* fconfig: Remove dead URLsRosen Penev2018-08-221-2/+1
| | | | | | uscan errors on the URL as it is no longer available. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* apex: Remove dead URL.Rosen Penev2018-08-221-2/+1
| | | | | | | | uscan errors on the URL as it is no longer available. Also switched the download URL to HTTPS. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ar71xx: add v4.14 supportJohn Crispin2018-08-22164-78/+8268
| | | | | | adds v4.14 patches for testing but leaves v4.9 as default for now. Signed-off-by: John Crispin <john@phrozen.org>
* iptables: make iptables-mod-conntrack-extra depend on kmod-ipt-rawJo-Philipp Wich2018-08-221-2/+2
| | | | | | | Since kernel 4.14 there is no auto assignment of conntrack helpers anymore so fw3 needs raw table support in order to stage ct helper assignment rules. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* dnsmasq: remove creation of /etc/ethersHans Dedecker2018-08-212-4/+1
| | | | | | | | Remove creation of file /etc/ethers in dnsmasq init script as the file is now created by default in the base-files package by commit fa3301a28e Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* base-files: create /etc/ethers by defaultLuiz Angelo Daros de Luca2018-08-212-0/+7
| | | | | | | | | | | /etc/ethers is missing on /rom but always created when dnsmasq runs. It is better to have it in place and avoid an extra change in flash after firstboot. It will generate an extra /etc/ethers-opkg when it has changed. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* uhttpd: update to latest Git headJo-Philipp Wich2018-08-211-3/+3
| | | | | | | 952bf9d build: use _DEFAULT_SOURCE 30a18cb uhttpd: recognize PATCH, PUT and DELETE HTTP methods Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mwlwifi: Update to 10.3.8.0-20180810Daniel Engberg2018-08-211-3/+3
| | | | | Update mwlwifi to 10.3.8.0-20180810 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* netifd: update to latest git HEADHans Dedecker2018-08-201-3/+3
| | | | | | | | | 7454d12 interface: let interface_set_down() return void 32f11a8 interface: make __interface_set_down() static b9d5a8c interface: extend interface error messages in interface_set_up() de394b3 interface: ensure NO_DEVICE error is always reported Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: bump 3.18 to 3.18.119Koen Vandeputte2018-08-2046-198/+173
| | | | | | | | | Refreshed all patches. Compile-tested on: adm5120, adm8668, au1000, mcs814x, ppc40x, ppc44x, xburst Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.65Koen Vandeputte2018-08-201-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.122Koen Vandeputte2018-08-204-6/+6
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* hostapd: process all CSA parametersYury Shvedov2018-08-201-6/+31
| | | | | | | This adds processing of all CSA arguments from ubus switch_chan request in the same manner as in the control interface API. Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
* toolchain/gcc: update 8.x to 8.2.0Syrone Wong2018-08-2021-8/+8
| | | | | | This release fixes LTO link-time performance problems and C++ bug introduced in GCC 8.1 Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
* toolchain/gcc: add config symbol to determine how to apply path remappingSyrone Wong2018-08-202-3/+8
| | | | | | | | | Added boolean symbol for GCC 8 and higher, when we add newer GCC, we don't have to modify rules.mk to keep things consistant. Fixes: da9d760 ("rules.mk: replace iremap when using GCC 8") Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
* target.mk: Remove obsolete octeon CPU_CFLAGSDaniel Engberg2018-08-191-1/+0
| | | | | | | As of commit c6e02b49f65cb4eff624a0831d3db265b3fadd2a the octeon target uses octeonplus instead of octeon Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ath79: fix TL-MR3020 image metadataDavid Bauer2018-08-191-1/+1
| | | | | | | | | | Sysupgrading to ath79 from ar71xx currently fails because of mismatching supported_devices. ar71xx is expecting "tl-mr3020" which is missing in the ath79 image. Upgrading from ath79 is unaffected, as the image contains the old string for ar71xx and the new one coming from the device-tree. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: cleanup PISEN WMM003N image metadataChuanhong Guo2018-08-191-1/+0
| | | | | | | PISEN WMM003N is never supported by ar71xx, this commit also removed SUPPORTED_DEVICES for it because it's completely useless. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Fritz!Box 4020David Bauer2018-08-195-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs The USB port doesn't work. Both Root Hubs are detected as having 0 Ports: [ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.723267] usbcore: registered new interface driver usbfs [ 3.729058] usbcore: registered new interface driver hub [ 3.734616] usbcore: registered new device driver usb [ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.758357] SCSI subsystem initialized [ 3.766026] ehci-platform: EHCI generic platform driver [ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller [ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00 [ 3.824001] hub 1-0:1.0: USB hub found [ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller [ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00 [ 3.894011] hub 2-0:1.0: USB hub found [ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.908928] usbcore: registered new interface driver usb-storage [ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/* A few words about the shift-register: AVM used a trick to control the shift-register for the LEDs with only 2 pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple shift-registers, pulls the latch, moving the shift register-state to the storage register. It also pulls down MR (normally pulled up) to clear the storage register, so the latch gets released and will not be pulled by the remaining bits in the shift-register. Shift register is all-zero after this. For that we need to make sure output 7 is set to high on driver probe. We accomplish this by using gpio-hogging. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer C7 v1Christian Lamparter2018-08-193-0/+56
| | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v1 is a dual band router based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: - 720 MHz CPU - 128 MB of RAM (Various chips) - 8 MB of FLASH (Various chips) - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi - minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!) - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch) - 10x LEDs, 2x software buttons For further informwation on the device, visit the wiki: <https://openwrt.org/toh/tp-link/archer-c7-1750> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* util-linux: Update to 2.32.1Daniel Engberg2018-08-161-3/+3
| | | | | | | | Update util-linux to 2.32.1 For release notes see https://lwn.net/Articles/759922/ Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: add support for I-O DATA WN-AC1167DGRINAGAKI Hiroshi2018-08-167-208/+245
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz wifi - 2.4 GHz: SoC internal - 5 GHz: QCA988x - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1167DGR 2. Connect power cable to WN-AC1167DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix leds and network for TP-Link TL-WR841 v9/v11Johann Neuhauser2018-08-162-7/+5
| | | | | | | | | Adding tl-wr841-v11 and the rename of tl-wr841n-v9 to tl-wr841-v9 in 01_leds and 02_network script files are missing in commits cc35c91 and 8db6522. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de> [merged with identical case in 02_network] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: don't use the pcs,cr5000 wps led as usb ledMathias Kresin2018-08-162-5/+1
| | | | | | | If it isn't a usb led, it shouldn't be used as one by default. It is up to the user to add such a (mis)configuration for the board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for TP-Link MR-3040 v2Dmitry Tunin2018-08-164-1/+178
| | | | | | Add support for the ar71xx supported TP-Link MR-3040 v2. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add support for Buffalo WHR-G301NINAGAKI Hiroshi2018-08-165-4/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240. Ported from ar71xx target. Specification: - Atheros AR7240 - 32 MB of RAM - 4 MB of Flash - 2.4 GHz 2T2R wifi - 5x 10/100 Mbps Ethernet - 9x LEDs, 4x keys - LED: 8x gpio-leds, 1x ath9k-leds - key: 2x buttons, 1x slide switch - UART header on PCB - Vcc, GND, TX, RX from LEDs side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WHR-G301N 2. Connect power cable to WHR-G301N and turn on it 3. Access to "http://192.168.11.1/" and open firmware update page ("ファーム更新") 4. Select the OpenWrt factory image and click execute ("実行") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [fix the SUPPORTED_DEVICES to be compatible with the ar71xx image] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add support for upgrade ledMathias Kresin2018-08-1636-0/+44
| | | | | | | | | | Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh script en par with the other implementations using devicetree aliases to define multiple leds for boot status indication. By default, use the boot finished led to indicate an upgrade for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop unused get_status_led functionsMathias Kresin2018-08-162-8/+0
| | | | | | | The function isn't used for targets getting the status leds from the devicetree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix upgrade led handlingMathias Kresin2018-08-164-8/+16
| | | | | | | | | | | | The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 20:22:35 +0000