aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: ath10k: fix max antenna gain unitSven Eckelmann2019-06-151-0/+49
| | | | | | | | | | | | | | | Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB steps). This isn't the case for max_antenna_gain - which is still expected by the firmware as dB. The firmware is converting it from dB to the internal (twicepower) representation when it calculates the limits of a channel. This can be seen in tpc_stats when configuring "12" as max_antenna_gain. Instead of the expected 12 (6 dB), the tpc_stats shows 24 (12 dB). Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* mac80211: ath9k: Increase allowed antenna gain to 6 dBiSven Eckelmann2019-06-151-3/+3
| | | | | | | | | | | | | | | | | | | | | | FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4): > (4) The conducted output power limit > specified in paragraph (b) of this section > is based on the use of antennas > with directional gains that do not exceed > 6 dBi. Except as shown in paragraph > (c) of this section, if transmitting > antennas of directional gain greater > than 6 dBi are used, the conducted > output power from the intentional radiator > shall be reduced below the stated > values in paragraphs (b)(1), (b)(2), > and (b)(3) of this section, as appropriate, > by the amount in dB that the > directional gain of the antenna exceeds > 6 dBi. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* kernel: mt29f_spinand: fix memory leak during page programMantas Pucka2019-06-151-0/+90
| | | | | | | | | Memory is allocated with devm_kzalloc() on every page program and leaks until device is closed (which never happens). Convert to kzalloc() and handle error paths manually. Signed-off-by: Mantas Pucka <mantas@8devices.com>
* iwinfo: update to latest git HEADKoen Vandeputte2019-06-121-2/+2
| | | | | | 1372f47eff34 iwinfo: Add Mikrotik R11e-5HnDr2 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)Koen Vandeputte2019-06-1227-1103/+352
| | | | | | | | | | | | | | | | Refreshed all patches. This bump contains upstream commits which seem to avoid (not properly fix) the errors as seen in FS#2305 and FS#2297 Altered patches: - 403-net-mvneta-convert-to-phylink.patch - 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: drop everything not on kernel version 4.14Daniel Golle2019-06-12738-113992/+0
| | | | | | | | | | * Remove testing patches for kernel version 4.19 * remove targets ar7, ixp4xx, orion Those targets are still on kernel 4.9, patches for 4.14 were not ready in time. They may be readded once people prepare and test patches for kernel 4.14. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* dnsmasq: move feature detection inside a shell funcYousong Zhou2019-06-112-7/+10
| | | | | | | Resolves openwrt/packages#9219 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com> (cherry picked from commit 04b45d3a31fac45c472ad3c31d98268d1c309763)
* OpenWrt v19.07: set branch defaultsAlexander Couzens2019-06-113-12/+7
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* version.mk: use https:// instead of http://Alexander Couzens2019-06-111-4/+4
| | | | | | | Only the repo should not use https. Otherwise the build would need a wget/uclient_fetch with tls support. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* replace links towards lede-project.org with openwrt.orgAlexander Couzens2019-06-113-3/+3
| | | | | | | Modify VERSION_SUPPORT_URL VERSION_REPO Replace BUGS variable in toolchain/gcc/common.mk Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* toolchain: replace LEDE in help textKarl Pálsson2019-06-101-2/+2
| | | | | | | Use generic wording. Signed-off-by: Karl Pálsson <karlp@etactica.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [fixed a -> á]
* ramips: Remove redundant LED-casesKristian Evensen2019-06-101-68/+32
| | | | | | | 01_leds has several redundant LED-cases. This commit cleans up the file by merging these cases into shared cases. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ath79: Add support for TP-Link Archer C25 v1Adrian Schmutzler2019-06-106-9/+231
| | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip, but not all of them as e.g. for the C59. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Reorder some TP-Link Archer devices in 01_ledsAdrian Schmutzler2019-06-101-8/+8
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: select kmod-rt2800-pci driver for RT5592Deng Qingfang2019-06-101-1/+3
| | | | | | | | | | | ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless After commit 367813b9b17 the driver for RT5592 (rt2800pci) is not selected by default anymore, which broke their 5GHz wireless Add it back to device packages Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies") Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ath79: migrate Archer C7 5GHz radio device pathsDavid Santamaría Rogado2019-06-101-6/+20
| | | | | | | | | | | | | | | | | | When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79, the 5ghz radio stops working because the device path changed. Some people subtitute the unsupported QCA9880v1 in the Archer v1 with supported QCA9880v2 radio. Since the stock radio doesn't work, so it's safe to apply the change also for the Archer v1 images as well. Also this patch renames the migration file and variables from wmac to wifi. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed comment, added return 0 (not that it matters since uci is clever, see 00-wmac-migration thread), reworded commit message]
* ath79: Consistently label art partition with lower caseAdrian Schmutzler2019-06-1019-36/+33
| | | | | | | | This patch harmonizes the label and alias for art partitions across ath79. Since lower case seems to be more frequent, use that consistently. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Read MAC addresses from flash in 11-ath10k-caldataAdrian Schmutzler2019-06-101-14/+23
| | | | | | | | | | In commit c3a8518 eth0 and eth1 have been swapped for some devices, but 11-ath10k-caldata has not been updated. Instead of fixing this by swapping eth0/eth1, this patch will read addresses from flash (as done for several devices already) so adjustments due to eth order become obsolete. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consistently label info partitionAdrian Schmutzler2019-06-107-15/+9
| | | | | | | | | | | | | | | | The info/product-info partition, which frequently contains MAC adresses, is typically assigned the 'info' alias in DTS, but then labelled with 'info', 'product-info' or 'config'. This leads to different aliases if used for setting MAC adresses in DTS compared to when using e.g. mtd_get_mac_binary. Occationally, also multiple switch-case entries are used just because of different labelling. This patch relabels those partitions in ath79 to consistently use 'info'. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: re-enable TL-WDR4900v1 imagesPawel Dembicki2019-06-101-1/+1
| | | | | | | | | This reverts commit 324e94f31bfd ("mpc85xx: disable bricking TL-WDR4900v1 images") The previous commit fixes the TL-WDR4900v1. Enable the target again. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: convert TL-WDR4900 v1 to simpleImageChristian Lamparter2019-06-108-212/+165
| | | | | | | | | | | | | | | | | Converts the TP-Link WDR4900 v1 to use the simpleImage in the hopes of prolonging the life of the device. While at it, the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE to 2684 KiB as a precaution since the stock u-boot is using a fixed kernel size. Note: Give the image some time, it will take much longer to extract and boot. [tested for 4.14/4.19] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* config: add xfrm interface support scriptsAndré Valentin2019-06-102-0/+103
| | | | | | | | | | | | | | | | | | | | | | | | This package adds scripts for xfrm interfaces support. Example configuration via /etc/config/network: config interface 'xfrm0' option proto 'xfrm' option mtu '1300' option zone 'VPN' option tunlink 'wan' option ifid 30 config interface 'xfrm0_static' option proto 'static' option ifname '@xfrm0' option ip6addr 'fe80::1/64' option ipaddr '10.0.0.1/30' Now set in strongswan IPsec policy: if_id_in = 30 if_id_out = 30 Signed-off-by: André Valentin <avalentin@marcant.net>
* curl: update to 7.65.1Hans Dedecker2019-06-101-2/+2
| | | | | | For changes in 7.65.1; see https://curl.haxx.se/changes.html#7_65_1 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netsupport: add xfrmi interface supportAndré Valentin2019-06-091-0/+16
| | | | | | | | Add support for xfrm interfaces in kernel. XFRM interfaces are used by the IPsec stack for tunneling. XFRM interfaces are available since linux 4.19. Signed-off-by: André Valentin <avalentin@marcant.net>
* kirkwood: image: fix unwanted 2nd inclusion of kernelPetr Štetiar2019-06-091-5/+5
| | | | | | | | | | | | | | | | | | | In commit d2e18dae2892 ("kirkwood: cleanup image build code") the image build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as the KERNEL_IN_UBI needs to be unset in order to make it working as intended, which leads to factory images with two kernels in them: binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin MD5 Checksum: c33e3d1eb0cb632bf0a4dc287592eb70 DECIMAL HEX DESCRIPTION ------------------------------------------------------------------------------- 0 0x0 uImage header [...] "ARM OpenWrt Linux-4.14.123" 5769216 0x580800 uImage header [...] "ARM OpenWrt Linux-4.14.123" Cc: Mathias Kresin <dev@kresin.me> Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285 Fixes: d2e18dae2892 ("kirkwood: cleanup image build code") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* gpio-button-hotplug: gpio-keys: fix always missing first eventPetr Štetiar2019-06-091-9/+2
| | | | | | | | | | | | | Commit afc056d7dc83 ("gpio-button-hotplug: support interrupt properties") changed the gpio-keys interrupt handling logic in a way, that it always misses first event, which causes issues with rc.button scripts, so this patch restores the previous behaviour. Fixes: afc056d7dc83 ("gpio-button-hotplug: support interrupt properties") Reported-by: Kristian Evensen <kristian.evensen@gmail.com> Tested-by: Kuan-Yi Li <kyli.tw@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [drop state check]
* gpio-button-hotplug: fix wrong initial seen valuePetr Štetiar2019-06-091-0/+3
| | | | | | | | | | | | | | | Currently the generated event contains wrong seen value, when the button is pressed for the first time: rmmod gpio_button_hotplug; modprobe gpio_button_hotplug [ pressing the wps key immediately after modprobe ] gpio-keys: create event, name=wps, seen=1088, pressed=1 So this patch adds a check for this corner case and makes seen=0 if the button is pressed for the first time. Tested-by: Kuan-Yi Li <kyli.tw@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* gpio-button-hotplug: use pr_debug and pr_errPetr Štetiar2019-06-091-17/+6
| | | | | | | pr_debug can be used with dynamic debugging. Tested-by: Kuan-Yi Li <kyli.tw@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* dnsmasq: skip options that are not compiled inYousong Zhou2019-06-092-3/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is to make life easier for users with customized build of dnsmasq-full variant. Currently dnsmasq config generated by current service script will be rejected by dnsmasq build lacking DHCP feature - Options like --dhcp-leasefile have default values. Deleting them from uci config or setting them to empty value will make them take on default value in the end - Options like --dhcp-broadcast are output unconditionally Tackle this by - Check availablility of features from output of "dnsmasq --version" - Make a list of options guarded by HAVE_xx macros in src/options.c of dnsmasq source code - Ignore these options in xappend() Two things to note in this implementation - The option list is not exhaustive. Supposedly only those options that may cause dnsmasq to reject with "unsupported option (check that dnsmasq was compiled with DHCP/TFTP/DNSSEC/DBus support)" are taken into account here - This provides a way out but users' cooperation is still needed. E.g. option dnssec needs to be turned off, otherwise the service script will try to add --conf-file pointing to dnssec specific anchor file which dnsmasq lacking dnssec support will reject Resolves FS#2281 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* netifd: xfrm tunnel supportHans Dedecker2019-06-081-3/+3
| | | | | | 8c6358b netifd: add xfrm tunnel interface support Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* busybox: add ALTERNATIVES for brctlKonstantin Demin2019-06-081-1/+2
| | | | | | | | Busybox brctl applet conflicts with the version from bridge-utils. Fix this by using ALTERNATIVE support for brctl in busybox. Signed-off-by: Konstantin Demin <rockdrilla@gmail.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
* tools/ccache: update to 3.7.1Deng Qingfang2019-06-082-3/+3
| | | | | | | | | Update ccache to 3.7.1 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_1 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* kernel: re-add bridge allow reception on disabled portChen Minqiang2019-06-073-9/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The "bridge allow reception on disabled port" implementation was broken after these commits: 08802d93e2c1 ("kernel: bump 4.19 to 4.19.37") b765f4be407c ("kernel: bump 4.14 to 4.14.114") 456f486b53a7 ("kernel: bump 4.9 to 4.9.171") This leads to issues when for example WDS is used, tied to a bridge: [ 96.503771] wlan1: send auth to d4:5f:25:eb:09:82 (try 1/3) [ 96.517956] wlan1: authenticated [ 96.526209] wlan1: associate with d4:5f:25:eb:09:82 (try 1/3) [ 97.086156] wlan1: associate with d4:5f:25:eb:09:82 (try 2/3) [ 97.200919] wlan1: RX AssocResp from d4:5f:25:eb:09:82 (capab=0x11 status=0 aid=1) [ 97.208706] wlan1: associated [ 101.312913] wlan1: deauthenticated from d4:5f:25:eb:09:82 (Reason: 2=PREV_AUTH_NOT_VALID) It seems upstream introduced a new patch, [1] so we have to reimplement these patches properly: target/linux/generic/pending-4.9/150-bridge_allow_receiption_on_disabled_port.patch target/linux/generic/pending-4.14/150-bridge_allow_receiption_on_disabled_port.patch target/linux/generic/pending-4.19/150-bridge_allow_receiption_on_disabled_port.patch [1] https://lkml.org/lkml/2019/4/24/1228 Fixes: 08802d93e2c1 ("kernel: bump 4.19 to 4.19.37") Fixes: b765f4be407c ("kernel: bump 4.14 to 4.14.114") Fixes: 456f486b53a7 ("kernel: bump 4.9 to 4.9.171") Signed-off-by: Chen Minqiang <ptpt52@gmail.com> [updated commit message and title] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* iproute2: add tc action ctinfo supportKevin Darbyshire-Bryant2019-06-072-1/+595
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the userspace control portion of the backported kernelspace act_ctinfo. ctinfo is a tc action restoring data stored in conntrack marks to various fields. At present it has two independent modes of operation, restoration of DSCP into IPv4/v6 diffserv and restoration of conntrack marks into packet skb marks. It understands a number of parameters specific to this action in additional to the usual action syntax. Each operating mode is independent of the other so all options are optional, however not specifying at least one mode is a bit pointless. Usage: ... ctinfo [dscp mask [statemask]] [cpmark [mask]] [zone ZONE] [CONTROL] [index <INDEX>] DSCP mode dscp enables copying of a DSCP stored in the conntrack mark into the ipv4/v6 diffserv field. The mask is a 32bit field and specifies where in the conntrack mark the DSCP value is located. It must be 6 contiguous bits long. eg. 0xfc000000 would restore the DSCP from the upper 6 bits of the conntrack mark. The DSCP copying may be optionally controlled by a statemask. The statemask is a 32bit field, usually with a single bit set and must not overlap the dscp mask. The DSCP restore operation will only take place if the corresponding bit/s in conntrack mark ANDed with the statemask yield a non zero result. eg. dscp 0xfc000000 0x01000000 would retrieve the DSCP from the top 6 bits, whilst using bit 25 as a flag to do so. Bit 26 is unused in this example. CPMARK mode cpmark enables copying of the conntrack mark to the packet skb mark. In this mode it is completely equivalent to the existing act_connmark action. Additional functionality is provided by the optional mask parameter, whereby the stored conntrack mark is logically ANDed with the cpmark mask before being stored into skb mark. This allows shared usage of the conntrack mark between applications. eg. cpmark 0x00ffffff would restore only the lower 24 bits of the conntrack mark, thus may be useful in the event that the upper 8 bits are used by the DSCP function. Usage: ... ctinfo [dscp mask [statemask]] [cpmark [mask]] [zone ZONE] [CONTROL] [index <INDEX>] where : dscp MASK is the bitmask to restore DSCP STATEMASK is the bitmask to determine conditional restoring cpmark MASK mask applied to restored packet mark ZONE is the conntrack zone CONTROL := reclassify | pipe | drop | continue | ok | goto chain <CHAIN_INDEX> Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: backport act_ctinfoKevin Darbyshire-Bryant2019-06-063-2/+1211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ctinfo is a new tc filter action module. It is designed to restore information contained in firewall conntrack marks to other packet fields and is typically used on packet ingress paths. At present it has two independent sub-functions or operating modes, DSCP restoration mode & skb mark restoration mode. The DSCP restore mode: This mode copies DSCP values that have been placed in the firewall conntrack mark back into the IPv4/v6 diffserv fields of relevant packets. The DSCP restoration is intended for use and has been found useful for restoring ingress classifications based on egress classifications across links that bleach or otherwise change DSCP, typically home ISP Internet links. Restoring DSCP on ingress on the WAN link allows qdiscs such as but by no means limited to CAKE to shape inbound packets according to policies that are easier to set & mark on egress. Ingress classification is traditionally a challenging task since iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT lookups, hence are unable to see internal IPv4 addresses as used on the typical home masquerading gateway. Thus marking the connection in some manner on egress for later restoration of classification on ingress is easier to implement. Parameters related to DSCP restore mode: dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the conntrack mark field contain the DSCP value to be restored. statemask - a 32 bit mask of (usually) 1 bit length, outside the area specified by dscpmask. This represents a conditional operation flag whereby the DSCP is only restored if the flag is set. This is useful to implement a 'one shot' iptables based classification where the 'complicated' iptables rules are only run once to classify the connection on initial (egress) packet and subsequent packets are all marked/restored with the same DSCP. A mask of zero disables the conditional behaviour ie. the conntrack mark DSCP bits are always restored to the ip diffserv field (assuming the conntrack entry is found & the skb is an ipv4/ipv6 type) e.g. dscpmask 0xfc000000 statemask 0x01000000 |----0xFC----conntrack mark----000000---| | Bits 31-26 | bit 25 | bit24 |~~~ Bit 0| | DSCP | unused | flag |unused | |-----------------------0x01---000000---| | | | | ---| Conditional flag v only restore if set |-ip diffserv-| | 6 bits | |-------------| The skb mark restore mode (cpmark): This mode copies the firewall conntrack mark to the skb's mark field. It is completely the functional equivalent of the existing act_connmark action with the additional feature of being able to apply a mask to the restored value. Parameters related to skb mark restore mode: mask - a 32 bit mask applied to the firewall conntrack mark to mask out bits unwanted for restoration. This can be useful where the conntrack mark is being used for different purposes by different applications. If not specified and by default the whole mark field is copied (i.e. default mask of 0xffffffff) e.g. mask 0x00ffffff to mask out the top 8 bits being used by the aforementioned DSCP restore mode. |----0x00----conntrack mark----ffffff---| | Bits 31-24 | | | DSCP & flag| some value here | |---------------------------------------| | | v |------------skb mark-------------------| | | | | zeroed | | |---------------------------------------| Overall parameters: zone - conntrack zone control - action related control (reclassify | pipe | drop | continue | ok | goto chain <CHAIN_INDEX>) Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Make suitable adjustments for backporting to 4.14 & 4.19 and add to SCHED_MODULES_FILTER Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* layerscape: update patches-4.14 to LSDK 19.03Biwen Li2019-06-0638-6688/+28071
| | | | | | | | | | | | | | | | | | | | All patches of LSDK 19.03 were ported to Openwrt kernel. We still used an all-in-one patch for each IP/feature for OpenWrt. Below are the changes this patch introduced. - Updated original IP/feature patches to LSDK 19.03. - Added new IP/feature patches for eTSEC/PTP/TMU. - Squashed scattered patches into IP/feature patches. - Updated config-4.14 correspondingly. - Refreshed all patches. More info about LSDK and the kernel: - https://lsdk.github.io/components.html - https://source.codeaurora.org/external/qoriq/qoriq-components/linux Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: fix u-boot bootcmdBiwen Li2019-06-063-0/+84
| | | | | | | | | | | Current latest LSDK-19.03 u-boot had a bug that bootcmd environment was always been reset when u-boot started up. This was found on boards with spi NOR boot. Before the proper fix-up is applied, we have to use a workaround to hard code the bootcmd for OpenWrt booting for now. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: drop ppa packageYangbo Lu2019-06-061-84/+0
| | | | | | Drop ppa package since TF-A is used instead. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: convert to use TF-A for firmwareBiwen Li2019-06-068-69/+59
| | | | | | | | | | This patch is to convert to use TF-A for firmware. - Use un-swapped rcw since swapping will be done in TF-A. - Use u-boot with TF-A defconfig. - Rework memory map for TF-A introduction. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add ARM Trusted Firmware packageBiwen Li2019-06-061-0/+140
| | | | | | | Add TF-A packages for Layerscape to implement trusted firmware. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add rcw packages for ls1043ardb/ls1046ardb SD bootBiwen Li2019-06-061-0/+12
| | | | | | | Add rcw packages for ls1043ardb/ls1046ardb SD boot. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: drop armv8_32b supportYangbo Lu2019-06-067-1155/+1
| | | | | | | NXP LSDK has decided to drop armv8_32b support considering few users are using it. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update restool to LSDK 19.03Yangbo Lu2019-06-061-3/+3
| | | | | | Update restool to LSDK 19.03. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update u-boot to LSDK 19.03Biwen Li2019-06-061-3/+3
| | | | | | | Update u-boot to LSDK 19.03. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update ppfe-firmware to LSDK 19.03Biwen Li2019-06-061-3/+3
| | | | | | | Update ppfe-firmware to LSDK 19.03. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update ls-rcw to LSDK 19.03Biwen Li2019-06-061-3/+3
| | | | | | | Update ls-rcw to LSDK 19.03. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update ls-mc to LSDK 19.03Biwen Li2019-06-061-5/+5
| | | | | | | Update to ls-mc to LSDK 19.03. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update ls-dpl to LSDK 19.03Biwen Li2019-06-061-3/+3
| | | | | | | Update ls-dpl to LSDK 19.03. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update fman-ucode to LSDK 19.03Biwen Li2019-06-061-2/+2
| | | | | | | The source code was same from lsdk-1806 to lsdk-1903. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: remove POSIX_MQUEUE configsYangbo Lu2019-06-063-6/+0
| | | | | | | The POSIX_MQUEUE configs had been handled by OpenWrt configuration. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 02:27:24 +0000