aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* firmware-utils: mktplinkfw2: replace "endian_swap" field with "flags"Rafał Miłecki2017-07-311-8/+10
| | | | | | This will allow adding more similar tricks needed by other hardware. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: Archer C50v1: fix power ledThibaut VARENE2017-07-292-1/+1
| | | | | | | | | | 01_leds had a workaround for the power led to compensate for the inverted GPIO state. This patch was missing from my previous commit. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> [add the power led default-state which was omitted in the last commit by me] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Archer C50v1: fix switch port numberingThibaut VARENE2017-07-291-1/+4
| | | | | | | | Luci shows switch ports in wrong order on that device. This patch fixes switch port numbering and matches them to the device silkscreen. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: Archer C50v1: fix LEDs active levelsThibaut VARENE2017-07-291-2/+2
| | | | | | | | | | All LEDs GPIOs are active low on this device. WAN and POWER states were inverted. Add default state for power. Tested on Archer C50v1. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: fix Mercury MAC1200R v2.0 board nameMathias Kresin2017-07-292-1/+2
| | | | | | | | | | | | With d2b6bf141662 ("ramips: fix image validation errors") the board name was changed to fix an image validation error. But this change wasn't applied to all other files using the board name, which broke sysupgrade. Revert this change and use the former board name in the metadata instead. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7621: add compatible stringsL. D. Pinney2017-07-2925-0/+27
| | | | | | | Add compatible strings to all mt7621 based device tree source files to fix formal issues. Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* brcm63xx: add NULL clock fix send upstreamMathias Kresin2017-07-295-5/+53
| | | | | | | | | | Make the behaviour of clk_get_rate consistent with common clk's clk_get_rate by accepting NULL clocks as parameter. Some device drivers rely on this, and will cause an OOPS otherwise. Fixes: FS#735 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add NULL clock fix send upstreamMathias Kresin2017-07-291-0/+43
| | | | | | | | | | Make the behaviour of clk_get_rate consistent with common clk's clk_get_rate by accepting NULL clocks as parameter. Some device drivers rely on this, and will cause an OOPS otherwise. Fixes: FS#735 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar7: add NULL clock fix send upstreamMathias Kresin2017-07-292-0/+90
| | | | | | | | Make the behaviour of clk_get_rate consistent with common clk's clk_get_rate by accepting NULL clocks as parameter. Some device drivers rely on this, and will cause an OOPS otherwise. Signed-off-by: Mathias Kresin <dev@kresin.me>
* openssl: update to version 1.0.2lLucian Cristian2017-07-284-10/+10
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* tcpdump: Update to 4.9.1Daniel Engberg2017-07-281-2/+2
| | | | | | | | | Update tcpdump to 4.9.1 Fixes: * CVE-2017-11108: Fix bounds checking for STP. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* kernel: update kernel 4.4 to version 4.4.79Hauke Mehrtens2017-07-2853-669/+96
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update kernel 4.9 to version 4.9.40Hauke Mehrtens2017-07-2812-35/+36
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* opkg: bump to version 2017-07-28Jo-Philipp Wich2017-07-281-3/+3
| | | | | | | | | | Commits since last 2017-07-11: 4bd8601 pkg_parse: fix segfault when parsing descriptions with leading newlines Fixes FS#933. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* brcm63xx: DTS: fix AV4202N flash layoutPaul Wassi2017-07-271-1/+1
| | | | | | | | Fix incorrect offset and size of linux partition. Fixes: 97b36aca09da ("brcm63xx: add pflash for remaining pflash equipped boards") Signed-off-by: Paul Wassi <p.wassi@gmx.at> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ramips: drop stray kernel 4.4 configsMathias Kresin2017-07-277-1494/+0
| | | | | | | The kernel 4.4 patches where already removed with the bump to 4.9. Drop the the subtarget configs as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Loewe WMDR-143NOliver Fleischmann2017-07-275-1/+79
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The WMDR-143N is a small module originally used as a Wifi client in some Loewe smart TV sets. It is sold cheaply at german surplus shops. The module contains a RT3662 SOC. Specifications: - 500 MHz CPU Clock - 1x 10/100Mbps Ethernet (pin header) - 32 MB of RAM - 8 MB of FLASH - 2T3R 2.4/5 GHz (SOC internal) - 3 Antennas on PCB - UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX and RX are 3,3V only! The square hole is pin 1 - Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND) The square hole is pin 1 The original firmware has two identical kernel/rootfs images and two "Factory" calibration data blocks in flash. The LEDE image leaves only the first "Factory" block in place and uses both "Kernel" blocks and the redundant "Factory" block together to gain enough space for the jffs2 partition. Flash instructions: You need UART and Ethernet connections to flash the board. Use the LEDE "sysupgrade.bin" image with tftp. Apply power to the board and in the first 5 seconds, hit 2 to select TFTP upload. The bootloader asks for board- and server IP addresses and filename. Alternate method: With the vendor firmware running, assign an IP address to the ethernet port, tftp the firmware image to /tmp and write to mtd4 ("KernelA"). Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de> [remove pinctrl node from dts, no pin is used as GPIO] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: pinctrl: return proper error if pinctrl0 is emptyMathias Kresin2017-07-271-1/+1
| | | | | | | | Children of the pinctrl0 node are optional. Return EINVAL (=missing) instead of 0. Fixes a hang if the pinctrl0 has no children. Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: John Crispin <john@phrozen.org>
* scripts/package-metadata.pl: inhibit compile deps on missing build typesJo-Philipp Wich2017-07-271-6/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a package declares a PKG_BUILD_DEPENDENCY or HOST_BUILD_DEPENDENCY on a not existing build type, the metadata script will emit a reference to an unresolvable build target in tmp/.packagedeps, causing the make process to fail hard in a way not catchable by the IGNORE_ERRORS mechanism. In a situation where a package "test-a" declares a build dependency "PKG_BUILD_DEPENDS:=test-b/host" while the Makefile of "test-b" does not implement a HostBuild, make fails with an unrecoverable error in the form: make[1]: Entering directory '...' make[1]: *** No rule to make target 'package/test-b/host/compile', needed by 'package/test-a/compile'. Stop. make[1]: Leaving directory '...' .../toplevel.mk:200: recipe for target 'package/test-a/compile' failed make: *** [package/test-a/compile] Error 2 Extend the metadata generation script to catch such unresolved references and emit a visable warning upon detection. After this change, the script will emit a warning similar to: WARNING: Makefile "package/test-a/Makefile" has a build dependency on "test-b/host" but "package/test-b/Makefile" does not implement a "host" build type Fixes a global build cluster outage which occured after the "python-cffi" feed package removed its HostBuild which the "python-cryptography" package build-depended on. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: refresh the rcu_sched patch and remove debug infoJohn Crispin2017-07-261-27/+6
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ralink: fix rcu_sched stalls on mt7621John Crispin2017-07-262-0/+132
| | | | | | | | there were 2 bugs *) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize *) HPT frequency was not set making r4k timers not come up properly Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add support for the GnuBee Personal Cloud OneL. D. Pinney2017-07-257-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com It is a low-cost, low-power, network-attached storage device. Specifications: - SoC: MediaTek MT7621AT - RAM: DDR3 512 MB - Flash: 32 MB - Six SATA ports for 2.5" Drives - One micro SDcard - One USB 3.0 - Two USB 2.0 - Gigabit Ethernet: 1 x WAN and 1 x LAN - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1 - Four GPIOs available on a pin header Flash instructions: The GnuBee Personal Cloud One ships with libreCMC installed. libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt. As such one can upgrade using the webinterface or sysupgrade. Das U-Boot has multiple options for recovery or updates including : - USB - http - tftp Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use switchdev led trigger, all interfaces are in vlan1; rename leds according to board.d setting; remove ge2 group from the pinmux, this group doesn't exist in the driver] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: DIR-860L-B1 fix switch port numberingThibaut VARENE2017-07-251-1/+4
| | | | | | | | Luci shows switch ports in inverted order on that device. This patch fixes switch port numbering and matches them to the device silkscreen. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* kernel: netfilter: fix nf-nathelper(-extra) descriptionUwe Arnold2017-07-251-2/+2
| | | | | | | | | The tftp and irc netfilter modules are provided by nf-nathelper-extra and not by nf-nathelper. Signed-off-by: Uwe Arnold <donvipre@gmail.com> [move the irc module as well] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix wps button gpio for DWR-512Giuseppe Lippolis2017-07-251-1/+1
| | | | | | The WPS button is at GPIO#7. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: DTS: VoCore2 improvements/fixesPaul Wassi2017-07-251-22/+3
| | | | | | | | | | | The VoCore2 features 128MB of RAM, therefore set memory in DTS to 128*1024*1024 = 0x8000000 The board's LED is connected to GND, set it to ACTIVE_HIGH here. Make serial console working again on kernel 4.9 by change of pinmux configuration. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ramips: add support for TP-Link RE350Alex Maclean2017-07-259-0/+207
| | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link RE350 is a wall-wart AC1200 range extender/access point with a single gigabit ethernet port and two non-detachable antennas, based on the MT7621A SoC with MT7603E and MT7612E radios. Firmware wise it is very similar to the QCA based RE450. SoC: MediaTek MT7621A (880MHz) Flash: 8MiB (Winbond W25Q64) RAM: 64MiB (DDR2) Ethernet: 1x 1Gbit Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E) LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act (green) Buttons: On/off, LED, reset, WPS Serial header at J1, 57600 8n1: Pin 1 TX Pin 2 RX Pin 3 GND Pin 4 3.3V Factory image can be uploaded directly through the stock UI. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* firmware-utils: tplink-safeloader: add support for TP-Link RE350Alex Maclean2017-07-251-0/+41
| | | | Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ath9k: fix regression in multicast buffering fixFelix Fietkau2017-07-251-1/+3
| | | | | | | Update the more data flag on the last frame, but tx from the first frame on. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath9k: fix typo in US tx power reduction fixFelix Fietkau2017-07-251-1/+1
| | | | | | Use max_t instead of min_t to prevent the value from going below zero Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: bundle-libraries.sh: do not override argv[0] in inner exec callsJo-Philipp Wich2017-07-241-1/+3
| | | | | | | | | | | Only mangle argv[0] of the first executed process and leave the argument vector of subsequent invocations as-is to allow child programs to properly discover resources relative to their binary locations. Fixes "cc1" discovery when executing the host gcc through the bundled "ccache" executable. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath9k: fix more-data flag for buffered multicast packetsFelix Fietkau2017-07-241-0/+38
| | | | | | | | The flag needs to be cleared for the last packet in the list, not the first one. Fixes some issues with multicast packet loss for powersave clients connected to an ath9k AP. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath9k: adjust tx power reduction for US regulatory domainFelix Fietkau2017-07-241-0/+23
| | | | | | | FCC regulatory rules allow for up to 3 dBi antenna gain. Account for this in the EEPROM based tx power reduction code. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* firmware-utils: drop mktplinkfw-kernel toolPiotr Dymacz2017-07-222-353/+0
| | | | | | | As we can now use combined mode in "mktplinkfw" tool to generate the same header/image, this tool is no longer needed. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: use tplink-v1-header in place of mktplinkfw-kernelPiotr Dymacz2017-07-221-13/+8
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* build: move mktplinkfw-combined command to image-commands.mkPiotr Dymacz2017-07-222-18/+13
| | | | | | | | | | We will need "mktplinkfw-combined" command also in the "ramips" target for new MediaTek based TP-Link devices, with "safeloader" image type. Also, rename the command to "tplink-v1-header", use "VERSION_DIST" variable instead of "OpenWrt" and allow passing additional parameters. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: mktplinkfw: rework combined image optionPiotr Dymacz2017-07-222-62/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | We use combined option in "mktplinkfw" tool for generating initramfs kernel images and header for kernel inside "safeloader" image type (in fact, only for TL-WR1043ND v4 at this moment). There is also "mktplinkfw-kernel" tool, a stripped-down version, used only for generating "simple" header, for safeloader image types. This changes how "mktplinkfw" handles combined images (which then will allow us to drop the stripped-down version of the tool): - drop "ignore size" command line option (it was used only for combined images anyway) - don't require "flash layout id" for combined images (we don't need and shouldn't limit size of the initramfs kernel and for kernels inside safeloader images, the "tplink-safeloader" tool does the size check) - require kernel address and entry point in command line parameters for combined images (consequence of previous point) - don't include md5 sum and firmware length values in header (they are needed only for update from vendor GUI and are ingored in case of initramfs and "tplink-safeloader" images) - drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to match introduced changes in "mktplinkfw" tool. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for ALFA Network AP121FPiotr Dymacz2017-07-221-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP121FPiotr Dymacz2017-07-2213-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users. Device is based on Atheros AR9331 WiSoC and is running a custom version (updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR1) - 16 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz - 1x microSD (optional, on separate PCB) - 3x LED, 1x button, 1x switch - UART header on PCB Flash instruction (under U-Boot web recovery mode): 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: tplink-safeloader: add support for TL-WR902AC v1 USPiotr Dymacz2017-07-221-1/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* samba36: Remove legacy optionsRosen Penev2017-07-222-8/+3
| | | | | | | | | | | | | Browseable is now set through LuCI per share, so remove it. Same with writeable (inverted synonym for read only). domain master and preferred master seem to be legacy settings for Windows 9x. encrypt passwords defaults to yes. Probably should not be disabled either. Also reordered alphabetically. Signed-off-by: Rosen Penev <rosenp@gmail.com> [rewrap commit message, fix SoB, fix author, bump pkg revsion] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mwlwifi: update to version 10.3.4.0 / 2017-07-13Jo-Philipp Wich2017-07-221-3/+3
| | | | | | Ref: https://github.com/lede-project/source/pull/1217 Reported-by: Kabuli Chana <newtownBuild@gmail.com> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* netifd: update to git HEADStijn Tintel2017-07-211-3/+3
| | | | | | | d397e8c netifd: Fix printf calls + function declarations. 34afb76 system-linux: fix GRE ikey/okey endianness Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* Revert "kernel: do not try to probe builtin modules on empty kmod package ↵Jo-Philipp Wich2017-07-211-2/+0
| | | | | | | | | | | install" This change currently causes some issues with loading out of tree kernel modules so revert that commit for now. Reverts commit 34c01e68b5d6b06ce3794ef0e2b06e81ec3ce8ca. Fixes FS#919. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mt76: update to the latest version, fixes stability issuesFelix Fietkau2017-07-211-3/+3
| | | | | | | | 8a649c3 mt7603: mac: code optimization 8dee788 mt7603: mac: stop netdev queues during watchdog reset 3c4c9a6 tx: move state check in mt76_txq_send_burst() Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipset: split libipset as a subpackageAlexandru Ardelean2017-07-211-6/+15
| | | | | | | | | | | Intent is to link against it, and have the option to not install the ipset utility (if needed). One example/use-case is keepalived (from package) feeds, where it would be nice to just depend on a `libipset` (sub)package. Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* ag71xx: add support for port mirroringMilan Krstić2017-07-211-0/+153
| | | | | | | This exposes hardware port mirroring in ag71xx driver (e.g. TL-WR841ND) via swconfig API. Signed-off-by: Milan Krstić <milan.krstic@gmail.com>
* dnsmasq: introduce config support for forced DHCP optionsJo-Philipp Wich2017-07-211-5/+9
| | | | | | | | | | | Introduce a new UCI list setting `list dhcp_option_force` which is available in sections of type `dnsmasq` and `dhcp`. The `dhcp_option_force` setting has the same semantics as `dhcp_option` but generates `dhcp-option-force` directives instead of `dhcp-option` ones in emitted native configuration. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* scripts/download.pl: Adjust URLsDaniel Engberg2017-07-211-5/+5
| | | | | | | | | | | | Internet2 isn't considered a trusted issuer meaning that https links to rit.edu will fail. The host mirror.csclub.uwaterloo.ca has a trusted SSL cert and peering is good so it can replace rit.edu without performance issues. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [Jo-Philipp Wich: rewrapped commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* build: fix invocation of bundled ld.so in SDK and ImagebuilderJo-Philipp Wich2017-07-211-15/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | Commit 72d751cba9 "build: rework library bundling" introduced a new helper binary "runas" whose sole purpose was mangling the argv vector passed to the actual called ELF image so that the renamed executable could obtain the proper name from argv[0]. This approach, however totally defeated the purpose of calling bundled ELF executables through the shipped ld.so loader since the execv() invocation performed by "runas" would cause the kernel the interprete the final program image through the system ELF loader again. To solve the problem, use an alternative approach of shipping a shared object "runas.so" which uses an ELF ".init_array" function pointer to obtain the argv[] vector of the to-be-executed main() function and mangle it in-place. The actual argv[0] value to use is communicated out-of-band using an environment variable "RUNAS_ARG0" by the shell wrapper script. The wrapper script also takes care of setting LD_PRELOAD to instruct the shipped ELF loader to preload the actual ELF program image with the "runas.so" helper library. Fixes FS#909. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 19:31:41 +0000