aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* x86: revert default root size back to 256 MBFelix Fietkau2016-12-151-2/+1
| | | | | | | | | | | 2 GB is overkill and was only added to allow unlimited ext4 resizing, which is a pretty rare use case. 256 MB allows resizing up to 256 GB, which should be good enough for almost all users. A lot of this is mostly irrelevant anyway, since you can just use squashfs + ext4 overlay. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* odhcpd: update sha256sumHauke Mehrtens2016-12-141-1/+1
| | | | | | | The sha256sum was not updated in the last commit. Fixes: a7c231027 [odhcpd: Fix dnsmasq re-reading hostfile] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* base-files: fix CONFIG_VERSION_DIST defaultJo-Philipp Wich2016-12-141-1/+1
| | | | | | Fix the default value of CONFIG_VERSION_DIST to use uppercase "LEDE". Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* build: use SNAPSHOT instead of CURRENT to designate untagged branch buildsJo-Philipp Wich2016-12-142-5/+5
| | | | | | | Calling a build ##.##-CURRENT might mislead users into thinking that this build is the most current release of a branch. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: fix TL-WR842N v2 switch port orderJo-Philipp Wich2016-12-141-1/+5
| | | | | | | | | | | | | | The TL-WR842N v2 has the following switch port layout with swconfig port 0 being connected to eth1: Power LAN4 LAN3 LAN2 LAN1 WAN USB (*) | [...] | [...] | [...] | [...] | [...] | [.] swconfig port: 1 4 3 2 n/a netdev: eth1 eth1 eth1 eth1 eth0 Adjust the board defaults to match this model specific layout. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: Added missing support for Linksys E2100LGad Krumholz2016-12-146-0/+143
| | | | | | | | | | | | | It's based on the WRT160NL according to https://wiki.openwrt.org/toh/linksys/e2100l Based on research done here: https://forum.openwrt.org/viewtopic.php?id=24244 and here: https://forum.openwrt.org/viewtopic.php?pid=120791#p120791 this patch was conceived. Signed-off-by: Gad Krumholz <gad.krumholz@gmail.com> [Jo-Philipp Wich: fix ordering, move addpattern change into separate commit] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firmware-utils: add E2100L support to addpattern.cJo-Philipp Wich2016-12-141-0/+7
| | | | | | Based on OpenWrt PR#250 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* linux: do not autoload sdhci.ko as sdhci-pltfm.ko already depends on itJo-Philipp Wich2016-12-141-1/+1
| | | | | | | | | | | Currently, installing kmod-sdhci fails with "sdhci is already loaded" since "sdhci.ko" is inserted explicitely first, the implicitely loaded again when "sdhci-pltfm.ko" is inserted as the latter depends on the former. Remove the explicit autoprobe of "sdhci.ko" to fix the postinstall script. Acked-by: John Crispin <john@phrozen.org> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* brcm63xx: image: trim revision code used for --rsa-signatureJo-Philipp Wich2016-12-141-3/+3
| | | | | | | | | | | | | | | | | The imagetag RSA signature field may not exceed 20 characters, so trim the Git hash portion from the REVISION variable in order to ensure that the resulting string fits within this field. The current revision values may be longer than 20 chars, especially when building within a dirty tree. In this case, the revision will look like "r2435+75-b4aa3c8" which, combined with the "LEDE-" prefix, is 21 chars long. Fixes the following error spotted by the buildbots: Error: RSA Signature (rsa_signature,r) too long. make[4]: *** [.../lede-brcm63xx-generic-NEUFBOX6-squashfs-cfe.bin] Error 1 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipkg-make-index.sh: drop a few non-essential fieldsFelix Fietkau2016-12-141-1/+1
| | | | | | Saves some more space on the package index Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipkg-make-index.sh: drop md5sum from package indexFelix Fietkau2016-12-141-3/+0
| | | | | | | We have switched opkg to sha256 a long time ago, and shrinking package lists is useful for systems that are running low on RAM Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: netfilter: split out iptable_raw into a separate packageFelix Fietkau2016-12-142-2/+22
| | | | | | | | This will avoid loading it in the default configuration, which reduces image size a bit, and (more importantly) improves performance by avoiding some unnecessary netfilter hooks Signed-off-by: Felix Fietkau <nbd@nbd.name>
* gcc: rip out transactional memory related bloat from crtbeginFelix Fietkau2016-12-142-0/+22
| | | | | | | Slightly improves compression for each executable, saving about 4k from the default ar71xx rootfs Signed-off-by: Felix Fietkau <nbd@nbd.name>
* swconfig: replace the shared library with a static oneFelix Fietkau2016-12-142-5/+5
| | | | | | Reduces binary size Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ppp: use --gc-sections to save a tiny bit of spaceFelix Fietkau2016-12-141-0/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libs/libpcap: update to 1.8.1p-wassi2016-12-148-202/+81
| | | | | | | | | | Update libpcap to upstream release 1.8.1 Change the name from libpcap.so.1.3 to libpcap.so.1 Remove parts of patch 201 which moved code among src files. Import patch 204 from Debian to update the USB path. Signed-off-by: Paul Wassi <p.wassi@gmx.at> Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix parallel build bug]
* ath10k: fix a soft-lockup on firmware restartFelix Fietkau2016-12-142-2/+51
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath10k: fix a bug on sending null-func framesFelix Fietkau2016-12-141-0/+42
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath10k-firmware: removed broken submenuAlberto Bursi2016-12-141-1/+0
| | | | | | | this package references an undefined variable for its submenu. Remove this NOP variable assignment. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kernel: add a missing submenuAlberto Bursi2016-12-141-0/+1
| | | | | | | this kernel module currently does not set submenu. Fix this by adding it to the "Others" submenu Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* comgt-ncm: Add support for specifying profile indexMatti Laakso2016-12-144-56/+51
| | | | | | | | | | | | | | | Add support for specifying a call profile index instead of APN. A specific index different from 1 must be used for some service provider and modem combinations. In addition, change the manufacturer detection to use the standard AT+CGMI command, which produces more predictable output than ATI, remove the redundant ipv6 option, since it is less ambiguous to directly specify the PDP context type with mobile connections, and fix missing device during teardown when using ncm through the wwan proto. Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
* uqmi: Add support for specifying profile indexMatti Laakso2016-12-142-82/+93
| | | | | | | | | | | | | | Update uqmi to latest version, which brings about support for specifying a call profile index instead of APN. A specific index different from 1 must be used for some service provider and modem combinations. Also change option dhcp to dhcpv6, since IPv4 now always uses DHCP, replace option ipv6 with pdptype, which is less ambiguous, and make autoconnect optional and default it to off for IPv6 due to it not working with statically configured IPv6. Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
* dropbear: clean up default PATH handling in makefileDario Ernst2016-12-142-14/+2
| | | | | | | | Harmonise handling of DEFAULT_PATH by removing the patch introducing #ifndef guards around the path, and only using one means to set the path in the makefile. Signed-off-by: Dario Ernst <Dario.Ernst@riverbed.com>
* ramips: adding DWM-158 3g ModemGiuseppe Lippolis2016-12-141-0/+14
| | | | | | | | | This patch add the 3G modem DWM-158 to the usb-serial option driver. The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem supportet by lede. The patch has been submitted and merged in the upstream linux-next repository. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ar71xx: Add support for Netgear WNR2000v1Huan Truong2016-12-144-44/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the WNR2000v1 board with 4MB flash, and produces device-specific factory, rootfs, and sysupgrade files for the WNR2000v1. This board is errorneously claimed as supported on the OpenWRT wiki as AP81, but AP81 image would not work because of APT81 image requiring having 8MB of flash, while WNR2000v1 has only 4MB. The image requires the u-boot bootloader to be modified to fuhry's bootloader first. Short specification: - CPU: Atheros AR9132 - 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps - 4 MB of Flash - 32 MB of RAM - UART header (J1) on board - 1x button Factory/Initial flash instructions: - Set up a TFTP server on your local machine. - Download the uImage for ar71xx-generic and the rootfs image for ar71xx-generic-wnr2000 and save in the tftp server root. - Gain serial access to the router via the UART port (telnetenable over the network only won't work!). - Upgrade the u-boot bootloader to fuhry's version by running the script: http://fuhry.com/b/wnr2000/install-repart.sh - When the router restarts, interrupt u-boot and gain access to u-boot command line. - Repartititon the board and flash initial uImage and rootfs as follow. Commands to type in u-boot: # tells u-boot that we have a tftp server on 192.168.1.10 setenv serverip 192.168.1.10 # tells u-boot that the router should take the address 192.168.1.1 setenv ipaddr 192.168.1.1 # erase the region from 0x050000-0x3f0000 erase 0xbf050000 +0x3A0000 # loads sqfs.bin on TFTP server, and put it to memory address 0x81000000 tftpboot 0x81000000 sqfs.bin # it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ # copy bit by bit 0xZZZZZZ bytes from offset 0x050000 cp.b 0x81000000 0xbf050000 0xZZZZZZ # same to the uImage.bin, write it right next to sqfs.bin # again, 0xYYYYYY is the length that tftpboot reports tftpboot 0x81000000 uImage.bin cp.b 0x81000000 0xbf2a0000 0xYYYYYY # We need to tell the kernel what board it is booting into, and where to find the partitions setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd" # Tell u-boot where to find the uImage setenv bootcmd "bootm 0xbf2a0000" # Tell u-boot to save parameters to the u-boot-env partitions saveenv # Reset the board reset Tested on: - WNR2000v1 board. - Initial flash works. Known bugs: - I don't know why factory image doesn't work on initial flash on stock firmware in u-boot recovery mode while it should. - Sysupgrade does not yet work, if you do -f it will mess up your installation (requiring a reinstall of sqfs and uImage). Signed-off-by: Huan Truong <htruong@tnhh.net>
* ar71xx: Add ath10k-firmware-qca988x for DomyWifi DW33DJing Lin2016-12-141-1/+1
| | | | | | | The default package selection was missing the correct FW for ath10k to work. Signed-off-by: Jing Lin <mumuqz@163.com>
* procd: add support for service signalsJo-Philipp Wich2016-12-142-4/+4
| | | | | | | | | | | | | | | | Update procd to latest HEAD in order to introduce support for services signals: - Adds a new service.signal ubus call to send a kill() signal to one or all running instances of a given service - Adds a new "reload_signal" property which allows service init scripts to request procd to send a specific kill() signal on reload, instead of stopping and restarting running processes Also fixes some potential memory leaks reported by cppcheck and an environment variable corruption in the trace command. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* netfilter: drop proprietary xt_id matchJo-Philipp Wich2016-12-145-356/+1
| | | | | | | | The xt_id match was used by the firewall3 package to track its own rules but the approach has been changed to use xt_comment instead now, so we can drop this nonstandard extension. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firewall3: drop support for automatic NOTRACK rulesJo-Philipp Wich2016-12-141-3/+3
| | | | | | | | | | | | Update to current HEAD in order to drop automatic generation of per-zone NOTRACK rules. The NOTRACK rules used to provide a little performance improvement but the later introduction of the netfilter conntrack cache made those rules largely unnecessary. Additionally, those rules caused various issues which broke stateful firewalling in some scenarios. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: kmod-hwmon-tmp102: add dependency to kmod-thermalHauke Mehrtens2016-12-141-1/+1
| | | | | | | Depend on the kmod-thermal package when it is activated, this fixes compile problems on some targets. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* odhcpd: Fix dnsmasq re-reading hostfileHans Dedecker2016-12-132-2/+5
| | | | | | | | | Depending on the dhcp uci config pidof dnsmasq can return multiple pids. Fix re-reading of the hostfile by dnsmasq in such case by sending SIGHUP signal to each of the returned pids. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* dnsmasq: Specify directory /tmp/hosts as argument for --addn-hostsHans Dedecker2016-12-132-2/+2
| | | | | | | Let dnsmasq read all hosts files in /tmp/hosts directory by specifying /tmp/hosts as argument of --addn-host Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath10k: fix DMA allocation issuesFelix Fietkau2016-12-132-0/+108
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: refresh all patchesFelix Fietkau2016-12-1310-42/+39
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath9k: add a RCU related bugfixFelix Fietkau2016-12-131-0/+65
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* download.mk: improve download tarball reproducibilityFelix Fietkau2016-12-131-1/+1
| | | | | | | Store only numeric user/group id. Group 0 is 'root' on linux and 'wheel' on BSD and Mac OS X. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* download.mk: remove code duplication in $(TAR) callFelix Fietkau2016-12-131-9/+12
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* download.mk: use $(error) instead of a regular shell errorFelix Fietkau2016-12-131-1/+1
| | | | | | Useful for further rework Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport ubifs support for dirty_writeback_intervalRafał Miłecki2016-12-132-0/+148
| | | | | | | These patches were queued for 4.10. For possible use cases see added: [PATCH] ubifs: Use dirty_writeback_interval value for wbuf timer Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport missed BCM53573 ILP patch from 4.10Rafał Miłecki2016-12-133-13/+39
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump to 4.4.38Kevin Darbyshire-Bryant2016-12-137-19/+19
| | | | | | | | Bump & refresh patches for all 4.4 supported targets. Compile & run tested: ar71xx - Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* bcm53xx: backport DTS patches accepted for 4.11Rafał Miłecki2016-12-138-160/+502
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* iproute2: support latest cake & restore DSCP washingKevin Darbyshire-Bryant2016-12-121-55/+75
| | | | | | | Support new packet overhead passing paradigm in cake qdisc, also restore DSCP wash/nowash keywords. Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* kmod-sched-cake: update & restore DSCP washingKevin Darbyshire-Bryant2016-12-121-4/+4
| | | | | | | | | | | | | | | | | | | | | | | Track upstream changes, incl changes in packet overhead accounting (automatically taking care of linux' packet sizing knowledge), improvements to triple isolated DRR handling (new flow dominance), statistics tweak & allow more packet drops in stressed conditions. Under tests this has significantly improved latency control under 'many flows to one' scenarious as is typical of bittorrent and MS Windows update. I also restored 'DSCP washing' functionality in my repo which follows upstream closely (like a hawk!) with tc keywords 'wash/nowash'. This allows cake to limit/control packets in bands determined by a packet's DSCP but to clear those DSCP bits on qdisc egress. This functionality was originally removed as part of an attempt to push cake into the kernel, which hasn't actually happened as yet. A matching commit is required to iproute2/tc to support the new overhead handling, keyword changes as well as the 'wash/nowash' tweak. Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* firmware-utils: tplink-safeloader: update support lists for CPE210/510/...Matthias Schiffer2016-12-121-4/+14
| | | | | | | Adds support for new EU and US variants; removes a few strings that were never actually used and have been removed from the stock firmwares. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: simplify model detection for TP-Link Pharos devicesMatthias Schiffer2016-12-121-19/+2
| | | | | | | This also makes the detection more flexible, as it doesn't need to check for each model explicitly. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* mt76: update to the latest version, fixes dfs issuesFelix Fietkau2016-12-121-2/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tcpdump: reduce size of -mini by removing more infrequently used protocolsFelix Fietkau2016-12-121-23/+25
| | | | | | | | | | | This removes: - BGP - CDP - SCTP MIPS binary .ipk size is reduced from ~150k to ~130k Signed-off-by: Felix Fietkau <nbd@nbd.name>
* net/utils/tcpdump: update to 4.8.1p-wassi2016-12-124-576/+700
| | | | | | Update tcpdump to upstream release 4.8.1 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* mbedtls: tune config to reduce size and improve performanceFelix Fietkau2016-12-121-5/+43
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>