aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)Anderson Vulczak2019-11-278-121/+308
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename EEPROM to artAdrian Schmutzler2019-11-2711-33/+31
| | | | | | | | | | | | | This renames all remaining occurrences of "EEPROM" to "art" to further harmonize the partition labelling in ath79. This will help to reduce the amount of user-space code and might be beneficial when code is copy/pasted in the future. Affected are only devices from Ubiquiti, where the XM board is already using "art" in ath79. Acked-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* wireguard: bump to 0.0.20191127Jason A. Donenfeld2019-11-271-2/+2
| | | | | | | | | | * messages: recalculate rekey max based on a one minute flood * allowedips: safely dereference rcu roots * socket: remove redundant check of new4 * allowedips: avoid double lock in selftest error case * tools: add syncconf command Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* procd: update to latest git HEADHans Dedecker2019-11-261-3/+3
| | | | | | 3aa051b system: sysupgrade: close input side of pipe before reading Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* uboot-envtools: ath79: add support for YunCore XD4200 and A782Piotr Dymacz2019-11-251-1/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for YunCore XD4200 and A782Piotr Dymacz2019-11-256-1/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based (QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE (802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller version of the XD4200, with similar specification but lower TX power. Specification: - QCA9563 (775 MHz) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN) - Wi-Fi 2.4 GHz: - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11) - Wi-Fi 5 GHz: - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11) - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11) - LEDs: - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet) - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet) - 1x button (reset) - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x DC jack (12 V) Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for YunCore TFTP image generationVincent Wiemann2019-11-252-0/+15
| | | | | | | | | | | | | | | | | | YunCore QCA9k based devices released in 2019 require a custom TFTP image for U-Boot built-in recovery mode (triggered with reset button). Image has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI commands which will be executed later. Images without the custom header will be ignored by U-Boot. To be able to support both the vendor firmware (QSDK) and OpenWrt flash layouts, used here commands change the 'bootcmd' before flashing image. This commit adds generic helper script for YunCore devices with 16 MB of flash and enables TFTP image generation for A770 model. Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com> [pepe2k@gmail.com: commit description reworded, recipe renamed] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: generic: base-files: fix indentation in 02_networkPiotr Dymacz2019-11-251-2/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* tools/expat: change package source to GitHubDavid Bauer2019-11-241-1/+1
| | | | | | | According to the SourceForge page, the project is migrating to GitHub. Thus, change the source of the package to GitHub. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: reorganize NETGEAR sercomm boardsDavid Bauer2019-11-245-65/+126
| | | | | | | | | | | | This re-organizes the device-tree files for the Sercomm-manufactured NETGEAR routers. They are now split into two different base-boards, from which the respective model is extended. This partially reverts commit c7842ceaaa27 ("ramips: reorganize DTSI files for Netgear R devices"), which introduced inheritance between two completely unrelated base-boards. Signed-off-by: David Bauer <mail@david-bauer.net>
* ccache: update to 3.7.6DENG Qingfang2019-11-242-3/+3
| | | | | | | | | Update ccache to 3.7.6 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_6 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* tools/quilt: update to 0.66Hannu Nyman2019-11-243-4/+4
| | | | | | | | | Update quilt to version 0.66 Release notes at: http://git.savannah.nongnu.org/cgit/quilt.git/tree/NEWS?id=294006e12 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* libubox: update to latest Git HEADPetr Štetiar2019-11-241-3/+3
| | | | | | | | | | | | | | | | | | | 07413cce72e1 tests: jshn: add more test cases 26586dae43a8 jshn: fix missing usage for -p and -o arguments 8e832a771d3a jshn: fix off by one in jshn_parse_file cb698e35409b jshn: jshn_parse: fix leaks of memory pointed to by 'obj' c42f11cc7c0f jshn: main: fix leak of memory pointed to by 'vars' 93848ec96dc5 jshn: refactor main into smaller pieces 9b6ede0e5312 avl: guard against theoretical null pointer dereference c008294a8323 blobmsg_json: fix possible uninitialized struct member 0003ea9c45cc base64: fix possible null pointer dereference 8baeeea1f52d add assert.h component b0a5cd8a28bf add cram based unit tests 1fefb7c4d7f9 add initial GitLab CI support c955464d7a9b enable extra compiler checks 6228df9de91d iron out all extra compiler warnings Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove ath10k drivers from Archer C7 v1 profileStijn Segers2019-11-241-1/+1
| | | | | | | | | | | Ath10k packages were removed from ar71xx in master in commit 34113999ef43 ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes FS#1743)") but ath79 in master and the 19.07 branch still suffer from the issue. Signed-off-by: Stijn Segers <foss@volatilesystems.org> [commit description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: kernel config: remove runtime optionsPetr Štetiar2019-11-2412-15/+0
| | | | | | | Remove CC_HAS_ASM_GOTO, CC_IS_GCC and GCC_VERSION kernel config options which are set at runtime and which should be ignored now. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel-build: ignore runtime config options during reconfigPetr Štetiar2019-11-241-1/+3
| | | | | | | | | Don't put CC_HAS_ASM_GOTO, IS_GCC, IS_CLANG and GCC_VERSION runtime config options into the kernel configs during reconfiguration as it makes no sense, since these options should be set at runtime. Fixes: FS#2588 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* nghttp2: bump to 1.40.0Hans Dedecker2019-11-231-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 41060943 Bump up version number to 1.40.0, LT revision to 33:0:19 5ae9bb89 Fail fast if huffman decoding context is in failure state bb519154 Merge pull request #1413 from nghttp2/check-authority 77f5487a Add nghttp2_check_authority as public API db9a8f6e Merge pull request #1409 from nghttp2/fix-wrong-stream-close-error-code 6f28a69b Merge pull request #1411 from richard78917/fix_warning 6ce4835e Fix the bug that stream is closed with wrong error code 29042f1c priority_spec::valid(): remove const qualifier from return value d08c4395 Merge pull request #1405 from nghttp2/huffman 5d6964cf Faster huffman decoding 0d855bfc Faster huffman encoding 6f967c6e Fix errors reported by coverity scan b8a43db8 Merge pull request #1394 from wrowe/fix-static-libname 70b62c1a Merge pull request #1393 from wrowe/fix-static-msvcrt 28b1f0b9 Avoid filename collision of static and dynamic lib 1dd966f1 Merge branch 'fix-nghttpx-mruby' fe8946dd nghttpx: Fix bug that mruby is incorrectly shared between backends 72b71a6b Add new flag ENABLE_STATIC_CRT for Windows f8933fe5 nghttpx: Reconnect h1 backend if it lost connection before sending headers 89c33d69 Update neverbleed 7079dc5e Update neverbleed to fix memory leak 5080db84 Revert "nghttpx: Reconnect h1 backend if it lost connection before sending headers" 053c7ac5 nghttpx: Returns 408 if backend timed out before sending headers 8a59ce6d nghttpx: Reconnect h1 backend if it lost connection before sending headers f2fde180 Remove redundant null check before delete 95efb3e1 Don't read too greedily 0a6ce87c Add nghttp2_option_set_max_outbound_ack 2aa79fa9 Bump up LT revision to 32:0:18 3980678d Merge branch 'nghttpx-fix-request-stall' 319d5ab1 nghttpx: Fix request stall 448bbbc3 integration-tests: gofmt e575a2aa Merge pull request #1377 from Aldrog/cmake_systemd 4f7aedc9 cmake: Support building nghttpx with systemd 7a590893 Fix clang-8 warning ee443134 Fix FPE with default backend abef9b90 Fix log-level is not set with cmd-line or configuration file 12a999f0 Bump up version number to 1.40.0-DEV acfb3607 Update manual pages Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: nf_conntrack_rtcache: fix WARNING on rmmodYousong Zhou2019-11-232-6/+2
| | | | | | | Fixes b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns delete and rmmod") Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kernel: nf_conntrack_rtcache: fix WARNING on forward pathYousong Zhou2019-11-232-22/+2
| | | | | | | | | Fixes b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns delete and rmmod") Resolves FS#2624 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* build: add PKG_SOURCE_URL_FILE supportKamil Wcislo2019-11-231-0/+1
| | | | | | | | | | | | | | It seems that there is a missing PKG_SOURCE_URL_FILE support. This little fix adds the support for packages to change the name of the downloaded file. Sometimes it is desirable to change the downloaded archive file name, like for mitigating name conflicts for different packages (some files on the server could be named like, e.g. 2018-01-01.tar.gz) or for the cases that there is no name for the file in the URL (e.g. http://someserver.com/download). Signed-off-by: Kamil Wcislo <kamil.wcislo@lpnplant.io> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ath79: improve TP-Link CPE DTSI names for ar9344 SOCAdrian Schmutzler2019-11-2312-11/+11
| | | | | | | | | | | The initial DTSI names for the TP-Link CPE devices have become quite confusing, as several non-V1 devices now use the *-v1.dtsi, the *cpe510-v1.dts does not use the cpe510.dtsi, etc. This introduces a new naming scheme based on whether devices have one or two ports, which should be easier to grasp. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tplink-safeloader: shorten version number of TP-Link WBS210 v2Bernhard Geier2019-11-231-3/+3
| | | | | | | | | "2.0" instead of "2.00" is sufficient and more in line with the other definitions. Signed-off-by: Bernhard Geier <freifunk@geierb.de> [commit message/title adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: config_generate: split macaddr with multiple ifacesSungbo Eo2019-11-232-7/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | netifd does not handle network.@device[x].name properly if it contains multiple ifaces separated by spaces. Due to this, board.d lan_mac setup does not work if multiple ifaces are set to LAN by ucidef_set_interface_lan. To fix this, create a device node for each member iface when running config_generate instead. Those are named based on the member ifname: ucidef_set_interface_lan "eth0 eth1.1" ucidef_set_interface_macaddr "lan" "yy:yy:yy:yy:yy:01" will return config device 'lan_eth0_dev' option name 'eth0' option macaddr 'yy:yy:yy:yy:yy:01' config device 'lan_eth1_1_dev' option name 'eth1.1' option macaddr 'yy:yy:yy:yy:yy:01' ref: https://github.com/openwrt/openwrt/pull/2542 Signed-off-by: Sungbo Eo <mans0n@gorani.run> [always use new scheme, extend description, change commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: DTS style improvement for Ubiquiti XM and BZ devicesAdrian Schmutzler2019-11-234-21/+13
| | | | | | | | | | This applies minor style improvements and removes commented pll clock adjustments from ubnt_xm DTSI. The latter were introduced (already commented out) when adding ath79 target and have never been touched since then. For Unifi (BZ board), similar clock adjustments are employed and used. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: nf_conntrack_rtcache: fix cleanup on netns delete and rmmodYousong Zhou2019-11-232-2/+26
| | | | | | | | Fixes FS#1472, FS#2353, FS#2426 Fixes: b3f95490 ("kernel: generic: Add kernel 4.14 support") Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: add default value for noscanSebastian Kemper2019-11-231-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | Commit b3d8b3a introduced a new test: [ -n "$noscan" -a "$noscan" -gt 0 ] && hostapd_noscan=1 But if length of "$noscan" is zero (noscan is not set) this doesn't stop the shell to evaluate the rest of the test. root@hank2:~# [ -n "$noscan" -a "$noscan" -gt 0 ] ash: out of range root@hank2:~# So when radios are brought up this shows in the log: Sat Nov 23 10:51:38 2019 daemon.info procd: - init complete - Sat Nov 23 10:52:24 2019 daemon.notice netifd: radio1 (1243): sh: out of range Sat Nov 23 10:52:25 2019 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2) Sat Nov 23 10:52:25 2019 daemon.notice netifd: radio0 (1242): sh: out of range Sat Nov 23 10:52:26 2019 authpriv.info dropbear[1536]: Not backgrounding This commit sets noscan to 0 if unset and removes the gratuitous length check, preventing the warning. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
* dnsmasq: correct sense & usage of dnsseccheckunsignedKevin Darbyshire-Bryant2019-11-232-2/+3
| | | | | | | | | | | | | dnsmasq v2.80 made 'dnssec-check-unsigned' the default, thus the uci option was rendered ineffectual: we checked unsigned zones no matter the setting. Disabling the checking of unsigned zones is now achieve with the "--dnssec-check-unsigned=no" dnsmasq option. Update init script to pass required option in the disabled case. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* e2fsprogs: Fix CVE-2019-5094 in libsupportHauke Mehrtens2019-11-222-1/+204
| | | | | | | | This adds the following patch from debian: https://git.kernel.org/pub/scm/fs/ext2/e2fsprogs.git/commit/?h=debian/stable&id=09fe1fd2a1f9efc3091b4fc61f1876d0785956a8 libsupport: add checks to prevent buffer overrun bugs in quota code Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: update to version 5.4-rc8Hauke Mehrtens2019-11-2218-386/+17
| | | | | | | | This updates mac80211 to backports based on kernel 5.4-rc8. The deleted patches were applied upstream. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Add missing configuration optionHauke Mehrtens2019-11-222-0/+2
| | | | | | | | This was found by the build bot. Fixes: e29500eb849a ("kernel: bump 4.19 to 4.19.85") Fixes: db9e9e838216 ("kernel: bump 4.14 to 4.14.155") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* firewall: update to latest Git HEADJo-Philipp Wich2019-11-221-3/+3
| | | | | | | 8174814 utils: persist effective extra_src and extra_dest options in state file 72a486f zones: fix emitting match rules for zones with only "extra" options Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* cns3xxx: use proper macros for defining partition regionsKoen Vandeputte2019-11-221-6/+8
| | | | | | | While at it, also reorder the items for improved readability. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.85Koen Vandeputte2019-11-2220-153/+59
| | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 080-sata_support.patch Remove upstreamed: - 034-v4.20-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch - 001-4.21-01-BCM63XX-fix-switch-core-reset-on-BCM6368.patch - 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.155Koen Vandeputte2019-11-2223-186/+79
| | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 707-dpaa-ethernet-support-layerscape.patch Remove upstreamed: - 034-v4.20-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch - 001-4.21-01-BCM63XX-fix-switch-core-reset-on-BCM6368.patch - 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for the TP-LINK WBS510 V1Andrew Cameron2019-11-226-1/+30
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for the TP-LINK WBS510 V2Andrew Cameron2019-11-226-2/+62
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* wireless-regdb: Make it build with python2Hauke Mehrtens2019-11-211-0/+58
| | | | | | | | This backports a patch to build it work with python2 in addition to python3. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: ubnt-(xm,xw): add rssileds packageLech Perczak2019-11-211-2/+8
| | | | | | | | | | | | | | | | | | In order to make RSSI indicator on the device work out of box, include "rssileds" package in per-device rootfs image by default for Ubiquiti XM and XW devices, namely: - Bullet M (XM/XW) - Rocket M (XM/XW) - Nanostation M (XM/XW) - Nanostation Loco-M (XW) This moves the package addition to the individual devices in order to prevent accidental inclusions of the package when not looking at the parent node carefully enough. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [add bullet-m-xw, remove rocket-m-ti, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add PoE passthrough switch for Ubiquiti Nanostation (XM/XW)Adrian Schmutzler2019-11-211-0/+6
| | | | | | | | | | | | | This adds the gpio switch to enable PoE passthrough on Ubiquiti Nanostation (XM/XW). Values are copied from the implementation in ar71xx. GPIO values checked on: - NanoStation M5 XW - NanoStation M2 XM Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* uboot-mvebu: add uDPU boardVladimir Vid2019-11-212-2/+22
| | | | | | | | | | * add u-boot support for uDPU * add line to copy u-boot binary to STAGING_DIR_IMAGE, this can later be used as BL33 variable required for ATF build * add patch to increase max gunzip size in mvebu_armada-37xx.h which is required for booting the itb recovery images Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* packages/boot: add arm-trusted-firmware-mvebu and initial uDPU supportVladimir Vid2019-11-211-0/+112
| | | | | | | | | | | | | | | | | ATF mvebu is required for building a functional bootloader for A7K/A8K and A37xx platforms. uDPU device is added as the first target. A3700 platform has a wide range of settings which can be used per device, so options are defined under the Device sections. Platform also required WTP (recovery) tools and mv-ddr package for the DDR topology configuration. 32-bit cross compiler is used for building the WTMI image. After the build, flash-image.bin can be used with the bubt command from the u-boot shell to flash the new version of u-boot. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* netifd: dhcp proto convert release to noreleaseKevin Darbyshire-Bryant2019-11-203-6/+29
| | | | | | | | Change dhcp no/release on shutdown to 'norelease' uci option to match existing proto dhcpv6 usage. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
* am33x-cm3: removeAndre Heider2019-11-201-42/+0
| | | | | | | | | | | | | | | This is currently unused and not working anyway, since the used upstream kernel loads am335x-pm-firmware.elf and not am335x-pm-firmware.bin [0]. The last downstream patches using the latter were removed with e4eef7e6. Remove it instead of fixing it since the rtc-only sleep state can even damage the hardware [1]. [0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ccbbb9faac946ce61c241ce9f08b3486fabf031d [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7a6cb0abe1aa63334f3ded6d2b6c8eca80e72302 Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: support booting off different mmc devicesAndre Heider2019-11-201-3/+7
| | | | | | Tested with installing to/sysupgrading from sd and emmc on boneblack. Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: switch from uEnv.txt to generic distro bootingAndre Heider2019-11-204-11/+8
| | | | | | Which makes supporting different boot devices easy. Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: update uboot to 2019.10Andre Heider2019-11-208-3592/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All patches have been dropped, they're either redundant (e.g. due to the new and unset CONFIG_SPL_FAT_WRITE), break compilation (thumb hacks) or have been applied upstream. The defconfig for am335x_boneblack has been removed upstream [0], so use am335x_evm for boneblack too. Size changes (before, after, file): ti_am335x-evm and ti_am335x-bone-black: 79804 110832 MLO 623836 756148 u-boot.img ti_omap3-beagle: 54148 57708 MLO 496272 665728 u-boot.img ti_omap4-panda: 39356 40204 MLO 284648 366672 u-boot.img Tested on boneblack, which has the biggest spl size increase. The beagle and panda spl sizes seem reasonable to not break booting. [0] https://gitlab.denx.de/u-boot/u-boot/commit/8fa7f65dd02c176ee6021eaf40114560b8954ba2 Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: switch to kernel 4.19Andre Heider2019-11-201-1/+1
| | | | Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: enable new sound kernel optionsAndre Heider2019-11-201-1/+5
| | | | | | | | This gets rid of a boot time warning about the missing edma module. Enable SND_OMAP_SOC_HDMI_AUDIO while here. All enabled options default to y. Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: disable excess kernel debug optionsAndre Heider2019-11-201-22/+1
| | | | Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: run `make oldconfig` for kernel 4.19Andre Heider2019-11-201-34/+72
| | | | | | | The only manually enabled config is the new OMAP4_DSS_HDMI_CEC, which defaults to y. Signed-off-by: Andre Heider <a.heider@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 03:44:39 +0000