aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* fstools: update to latest git HEADJohn Crispin2018-01-131-3/+3
| | | | | | | | 18090d9 overlay: fix compilation with glibc 2a9a6ea libfstools: optimize building directory string for glob de6b026 libfstools: support file paths longer than 255 chars Signed-off-by: John Crispin <john@phrozen.org>
* config: support new symbol intro'd in kernel 4.12Koen Vandeputte2018-01-132-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Symbol CONFIG_INITRAMFS_FORCE allows to ignore the value passed by the bootloader. By default, all symbols containing INITRAMFS are wiped from the final config and then re-added conditionally. Add support for this symbol, as the build will stop otherwise questioning the user about this option: * Restart config... * * * General setup * Cross-compiler tool prefix (CROSS_COMPILE) [] Compile also drivers which will not load (COMPILE_TEST) [N/y/?] n ... Initial RAM filesystem and RAM disk (initramfs/initrd) support (BLK_DEV_INITRD) [Y/n/?] y Initramfs source file(s) (INITRAMFS_SOURCE) [] Ignore the initramfs passed by the bootloader (INITRAMFS_FORCE) [N/y/?] (NEW) Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* target: disable CONFIG_PROC_PAGE_MONITOR on most targetsJo-Philipp Wich2018-01-1311-12/+0
| | | | | | | | | | Disable CONFIG_PROC_PAGE_MONITOR in most places and only keep it enabled for virtual targets such as malta or potent ones like x86. This saves up to 4KB of uncompressed kernel size and significantly decreases CPU load under certain workloads. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: add support for OpenMesh A42Sven Eckelmann2018-01-137-1/+388
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ401x * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet * powered only via POE - 802.3af POE on Ethernet 1 - 18-24v passive POE (mode B) on Ethernet 2 The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq806x: enable gpio watchdog supportSven Eckelmann2018-01-131-0/+2
| | | | | | | | | The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to trigger external gpio watchdog chips. The gpio-wdt driver has the benefit that it can be configured together with the rest of the device in the DTS and better integrates in the OpenWrt via procd. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* om-fwupgradecfg-gen.sh: add support for the A42Sven Eckelmann2018-01-131-4/+18
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* build: add image command for CE imagesSven Eckelmann2018-01-131-0/+13
| | | | | | | | | Combined Extended Images V1 can be created easily via the new image commands using IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | combined-ext-image Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* combined-ext-image.sh: generate image in temp dirSven Eckelmann2018-01-131-6/+23
| | | | | | | | | | | | | The new build commands operate on the input image and use it again as output image. This conflicts with the way combined-ext-image.sh was operating. It required that input and output files are different files and and that it can write freely to the output file. This can be avoided when all intermediate build steps by combined-ext-image.sh are done in a temporary directory. The output file is then only overwritten in the last step. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* uboot-envtools: add OpenMesh A42 supportSven Eckelmann2018-01-131-0/+3
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq-wifi: add board-2.bin for OpenMesh A42Sven Eckelmann2018-01-132-1/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* mac80211: ath10k: search DT for BDF variant infoSven Eckelmann2018-01-131-0/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Board Data File (BDF) is loaded upon driver boot-up procedure. The right board data file is identified on QCA4019 using bus, bmi-chip-id and bmi-board-id. The problem, however, can occur when the (default) board data file cannot fulfill the vendor requirements and it is necessary to use a different board data file. This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8. Something similar has to be provided for systems without SMBIOS but with device trees. No solution was specified by QCA and therefore a new one has to be found for ath10k. The device tree requires addition strings to define the variant name wifi@a000000 { status = "okay"; qcom,ath10k-calibration-variant = "RT-AC58U"; }; wifi@a800000 { status = "okay"; qcom,ath10k-calibration-variant = "RT-AC58U"; }; This would create the boarddata identifiers for the board-2.bin search * bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U * bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq806x: Sort occurrences of boardame alphabeticallyLuis Araneda2018-01-137-173/+172
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: convert to dt-based board-detectionLuis Araneda2018-01-1311-156/+91
| | | | | | | | | | | | | | | | | Use the generic board detection method: - Board name: First compatible string from the device tree - Board model: Model property from the device tree Change occurrences of board name in userspace by the compatible string, and removed target specific board detection script Replace the definition of SUPPORTED_DEVICES in Device/Default to extract the dt compatible string from each device definition. Additionally, for devices supported by lede-17.01, append the value of BOARD_NAME to SUPPORTED_DEVICES in the device definition. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: sync image filename with dt compatible stringLuis Araneda2018-01-131-28/+28
| | | | | | | Use <manufacturer>_<modelname> as image name for board using the devicetree compat string as boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: add a helper variable with the vendor name strippedLuis Araneda2018-01-131-0/+1
| | | | | | | | | | This will allow to maintain the current syntax for LEDs config when switching to a device tree compatible string boardname. None of the current boards use a comma in the boardname, so they will be unaffected. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: add missing dt compatible string to ap-dk04 boardLuis Araneda2018-01-131-1/+2
| | | | | | Compatible string is mandatory to dts files Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: drop partitial supported boardsMathias Kresin2018-01-137-367/+2
| | | | | | | | | There are only artifacts for these boards in our tree and not even partial support. Drop teh stale files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* armvirt: Resync kernel configurationFlorian Fainelli2018-01-121-107/+36
| | | | | | | | The 4.14 kernel configuration defaulted to a v4/v5 multiplatform while 4.9 was using a v6/v7 default configuration. Resync 4.14 against 4.9 so they are nearly identical. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* kernel: Add a bunch of missing symbolsFlorian Fainelli2018-01-121-0/+6
| | | | | | | | Add a bunch of missing configuration symbols found while building armvirt for 4.14 after re-synchronization of the configuration between 4.9 and 4.14. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* bcm53xx: rename SPI driver fix to use 0xx prefix as it was acceptedRafał Miłecki2018-01-123-0/+0
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use upstream fix for PCI iproc driver regressionRafał Miłecki2018-01-122-29/+80
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* base-files: sysupgrade: correct command help textKevin Darbyshire-Bryant2018-01-122-2/+1
| | | | | | | | | | Commit 30f61a34b4cfd2c676fea4a919e089d6a77254e9 claimed to drop -d & -p options. In reality only -d was dropped. Update command help text to reflect that -d is no longer a supported option. Fixes FS#1187 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: fix cpuclock for the GB-PC1Rosen Penev2018-01-121-0/+5
| | | | | | The GnuBee PC1 stock bootloader runs at 900Mhz. This fixes bad clock drift when running the platform. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* apm821xx: remove kernel 4.9 supportChristian Lamparter2018-01-1214-2682/+0
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: switch to 4.14.x kernelChristian Lamparter2018-01-121-1/+1
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: backport crypto4xx patches from 4.15Christian Lamparter2018-01-1231-0/+4686
| | | | | | | This patch backports changes to crypto4xx in order to get the crypto4xx operational. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: convert MR24 to use DT PHY defintionChristian Lamparter2018-01-125-0/+369
| | | | | | Convert the MR24 to use the DT phy probing and at803x PHY driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add linux 4.14 apm821xx patchesChristian Lamparter2018-01-1214-3/+1458
| | | | | | | | | | | This patch updates the apm821xx target to use the 4.14 kernel. 4.14 finally ships with a driver for the WNDR4700's tc654 fan controller. The custom driver is deprecated in favor of the upstream driver and the thermal cooling definitions in the DTS are updated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kmod-sched-cake: bump to latest cake bakeKevin Darbyshire-Bryant2018-01-111-3/+3
| | | | | | | | | | | | | | | | | More important bug fix: 402f05c Use full-rate mtu_time in all tins. Fixes an issue where some cake tins experienced excessive latency since 49776da (dynamically adjust target) Minor bug fixes: 31277c2 Avoid unsigned comparison against zero. Fix compiler warning, no known impact. 8cf5278 ack_filter: fix TCP flag check. A very contrived case may have lead to dropping a SYN packet that should not be dropped. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* at91: create device specific sdcard imagesHauke Mehrtens2018-01-111-4/+4
| | | | | | | | | | Without this patch one sdcard image with the following name is created for all devices: openwrt-at91-sama5--sdcard.img.gz This makes the build system create device specific versions like: openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.13Kevin Darbyshire-Bryant2018-01-114-10/+10
| | | | | | Refresh patches Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.4 to 4.4.111Kevin Darbyshire-Bryant2018-01-113-5/+5
| | | | | | | | Refresh patches Tested-on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.9 to 4.9.76Kevin Darbyshire-Bryant2018-01-113-15/+15
| | | | | | | | | Refresh patches Tested-on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* build: fix restoring /etc/opkg with PER_DEVICE_ROOTFSJo-Philipp Wich2018-01-111-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When generating per-device rootfs directories, the ./etc/opkg/ directory is moved away prior to calling opkg install, opkg remove and rootfs_prepare. After the opkg invocations and the rootfs_prepare macro call, the saved opkg config directory is supposed to be moved back to its previous ./etc/opkg location. The mv command however can fail to properly restore the directory under certain circumstances, e.g. when the prior opkg or files/ overlay copy operations caused a new ./etc/opkg/ directory to be created. In this case, the backed up directory (named target-dir-$hash.opkg) will be moved into the preexisting ./etc/opkg/ directory instead, causing the opkg configuration to be located in a wrong path on the final rootfs, e.g. in /etc/opkg/target-dir-$hash.opkg/distfeeds.conf instead of /etc/opkg/distfeeds.conf. Solve this problem by replacing the naive "mv" command with a recursive "cp -T" invocation which causes the backed up directory tree to get merged with the destination directory in case it already exists. Also perform the rootfs_prepare macro call after restoring the opkg configuration, to allow users to override it again by using the files/ overlay mechanism. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* sdk: change base feed fallback to git.openwrt.orgJo-Philipp Wich2018-01-111-1/+2
| | | | | | | Change the hardcoded lede-project.org base feed fallback to $(PROJECT_GIT)/openwrt/openwrt.git instead. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* bcm53xx: replace linux,part-probe with a proper partitions subnodeRafał Miłecki2018-01-115-22/+106
| | | | | | | | | This solution is more upstream compatible as it only requires specifying of_match_table in the parser code and doesn't depend on linux,part-probe which is solution made generic by a LEDE downstream patch that can't be upstreamed. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport mtd implementation for "compatible" in "partitions" subnodeRafał Miłecki2018-01-1118-56/+386
| | | | | | | | | | | This backports upstream support for "compatible" DT property set for the "partitions" subnode of flash node. It allows specifying how partitions should be created/parsed. Right now only "fixed-partitions" is supported. It should eventually replace our downstream "linux,part-probe" solution. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: allow disabling multicast routing supportMatthias Schiffer2018-01-115-5/+20
| | | | | | | | Multicast routing support is not needed in most setups, and increases the size of the kernel considerably (>10K after LZMA). Add a config switch to allow disabling it. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* generic: unlock Winbond flash on bootMatthias Schiffer2018-01-112-0/+74
| | | | | | | | | | | | The underlying issue breaking Spansion flash has been fixed with "mtd: spi-nor: wait until lock/unlock operations are ready" and "mtd: spi-nor: wait for SR_WIP to clear on initial unlock", so we can support unlocking for Winbond flash again. This is necessary to have writable flash on certain UBNT devices with some bootloader versions. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ebtables: update to latest git 2017-10-24Matthias Schiffer2018-01-111-3/+3
| | | | | | | 6a82659 Use flock() for --concurrent option 73c2371 ebtables: extensions: Constify option struct Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* sunxi: enable missing config symbolJo-Philipp Wich2018-01-111-0/+1
| | | | | | | | Enable CONFIG_MFD_AXP20X_I2C after the switch to Kernel 4.9, this symbol is reportedly required to get USB working on the Banana Pi. Ref: https://forum.lede-project.org/t/sunxi-kernel-4-9-usb-not-working/10513 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* omcproxy: silence fw3 warningsHans Dedecker2018-01-102-3/+3
| | | | | | Silence fw3 warnings in omcproxy init script in case fw3 is not enabled Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* treewide: replace LEDE_GIT with PROJECT_GITJo-Philipp Wich2018-01-1025-25/+25
| | | | | | | Remove LEDE_GIT references in favor to the new name-agnostic PROJECT_GIT variable. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* downloads.mk: introduce name-agnostic PROJECT_GIT variableJo-Philipp Wich2018-01-101-2/+4
| | | | | | | | | | Introduce a name-agnostic PROJECT_GIT variable poiting to https://git.openwrt.org/ and declare LEDE_GIT and OPENWRT_GIT as aliases to it. After some transition time we can drop this alias variables. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* netifd: update dhcp.script to handle dynamic routingMogula Pranay2018-01-102-2/+8
| | | | | | | | | | | | Certain DHCP servers push a gateway outside of the assigned interface subnet, to support those situations, install a host route towards the gateway. If Gateway and IP are served in same network, openwrt quagga cannot learn routes (rip routes are not getting added, showing inactive) whereas working fine when Gateway and IP are in different network. Signed-off-by: Mogula Pranay <mogula.pranay@nxp.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ltq-xdsl-app: drop script for renaming the netdevMathias Kresin2018-01-104-22/+6
| | | | | | | Our netdevs are named dsl by default now, the rename via scripts isn't required anymore. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: create ATM/PTM interfaces with dsl as netdev nameMathias Kresin2018-01-104-5/+17
| | | | | | | | | | | | | | | | | | | | | Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the original netdev might disappear before br2684ctl has finished appling it's setting: local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC kern.info kernel: dsl0: renamed from nas0 kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device local2.err br2684ctl[1667]: Could not configure interface:No such device or address By passing the final used netdev name to br2684ctl_wrap another race condition workaround will be enabled again. Change the lantiq ptm driver to create a netdev with the name dsl as well. Albeit the rename via 'ip link' works fine so far, using a different approach for ptm then atm could be confusing. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ltq-xdsl-app: drop manual br2684ctl reloadMathias Kresin2018-01-102-4/+0
| | | | | | | | | | br2684ctl starts automatically, set up reload triggers, which fire as soon as a atm driver is loaded. No need to do the reload via the script. The reload is only required as soon as we can reliable switch between atm and ptm driver and need to be implemented in a race free way. Signed-off-by: Mathias Kresin <dev@kresin.me>
* linux-atm: add br2684ctl option to specify the netdev nameMartin Schiller2018-01-104-4/+84
| | | | | | | | | | | Add the uci option nameprefix to specifc a target netdev name. Patch the br2684ctl code to accept and set a netdev name via commandline parameters. It allows to use the same netdev name for ATM and PTM lines on lantiq xdsl hardware. Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Mathis Kresin <dev@kresin.me>
* armvirt: re-enable VFP supportJo-Philipp Wich2018-01-101-1/+0
| | | | | | | | | | Enable CONFIG_VFP again which was disabled during the 4.9 -> 4.14 bump. Boot tested both 32 and 64 bit subtargets using initramfs images with the qemu-system-arm and qemu-system-aarch64 emulators. Fixes: aa100b66f2 ("armvirt: bump to v4.14") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 22:06:13 +0000