aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: fix remaining IMAGE_SIZE issuesAdrian Schmutzler2019-10-272-1/+2
| | | | | | | | This fixes the remaining IMAGE_SIZE issues in ath79 target. All devices in target have been checked, so together with previous patches this target should be "clean" afterwards. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix IMAGE_SIZE for common TP-Link definitionsAdrian Schmutzler2019-10-271-3/+3
| | | | | | | | | | | | | | | | | | | So far, IMAGE_SIZE is set as follows: tplink-4m* 3904k 0x3d0000 tplink-8m* 7936k 0x7c0000 tplink-16m* 15872k 0xf80000 However, based on the size of firmware partitions in DTS it should be: tplink-4m* 3904k 0x3d0000 tplink-8m* 8000k 0x7d0000 tplink-16m* 16192k 0xfd0000 All (!) 8m*/16m* devices actually follow the latter scheme, which is also consistent in terms of left free space for other partitions. Thus, fix it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: tidy up and fix IMAGE_SIZE for Ubiquiti devicesAdrian Schmutzler2019-10-271-5/+4
| | | | | | | | | | | | This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by: 1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"), since despite two all subdefinition have different values. 2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k). 3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node since all have same size (it is defined in parent DTSI ...). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: wnr1000v2: fix image header informationMichal Cieslakiewicz2019-10-271-0/+2
| | | | | | | | Factory image generated for Netgear WNR1000 v2 has incorrect device and hardware ID information in header due to missing makefile variables. This fix adds them to device section. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for ZyXEL NBG6716André Valentin2019-10-278-1/+387
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Attention: Kernel partition size has been enlarged to 4MB. To switch, you must update to latest ar71xx-nand snapshort and flash the sysupgrade-4M-Kernel.bin: zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f You will end up with a fresh config if you do not inject config into the image. The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but ath79 can only use the first 128MB. Therefore the complete NAND needs to be overwritten. If not, the old UBI may make problems and lead to reboot loop. Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6716> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6716> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6716> ATSE NBG6716 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6716> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6716> ATGU |NBG6716# Signed-off-by: André Valentin <avalentin@marcant.net>
* ar71xx: fix bug in NBG6716 kernelpacking, add firmware partitionAndré Valentin2019-10-271-2/+3
| | | | | | | -Fix the kernel image generation (more robust) -Add a firmware partition table allowing easy upgrade to ath79 Signed-off-by: André Valentin <avalentin@marcant.net>
* tools/mkrasimage: Add support for 128k header sizeAndré Valentin2019-10-271-3/+8
| | | | | | 128k header size support is needed for ZyXEL NBG6716. Signed-off-by: André Valentin <avalentin@marcant.net>
* ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2Paul Fertser2019-10-273-1/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - CMIIT ID: 2019AP2581 - SoC: MediaTek MT7621 - Flash: 16MiB NOR SPI (GigaDevice GD25Q128B) - RAM: 128MiB DDR3 (ESMT M15T1G1664A) - Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset INSTALLATION: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware (looks like an illegal OpenWrt fork) won't accept any serial input unless "uart_en" is set to "1". Tricks to force u-boot to use default environment do not help as it's restricted in the same way. With bootloader unlocked the easiest way would be to TFTP the sysupgrade image or to sysupgrade after loading an initramfs one. For porting the flash contents were changed externally with an SPI programmer (after lifting Vcc flash IC pin away from the PCB). Forum thread [0] indicates that this device is identical to "Xiaomi Mi Router 4A Gigabit Edition". [0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* octeontx: fix thunderx BGX underflow irq nameTim Harvey2019-10-271-4/+11
| | | | | | request_irq requires irq names to be static/allocated and not on the stack Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* ramips: remove phy0tpt trigger from RT-AC65P/RT-AC85P power LEDAdrian Schmutzler2019-10-271-1/+0
| | | | | | | | | | | | This patch removes a phy0tpt trigger from the power LED, which seems to have been added by mistake. WiFi LEDs using phy0radio and phy1radio triggers are present and used correctly. Cc: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant mtd-eeprom in mt76x8 DTS filesAdrian Schmutzler2019-10-278-9/+0
| | | | | | | | | | In mt7628an.dtsi, calibration data for wmac is already defined: mediatek,mtd-eeprom = <&factory 0x0>; Thus, this patch removes redundant entries of this property in derived DTS files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant mtd-mac-address for WiFiAdrian Schmutzler2019-10-273-4/+1
| | | | | | | | | | When caldata locations are defined with mediatek,mtd-eeprom the MAC address is automatically read from offset +4. Thus, specifying that location explicitly is redundant. This patch removes those redundant definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: mtd: spinand: Backport chip definitionsJeff Kletsky2019-10-249-11/+870
| | | | | | | | | | | | | | | | | | | | | | | | | | generic: Add/rename patches for upstream consistency ipq40xx: generic-level patch replaces same-source patches-4.19/ 082-v4.20-mtd-spinand-winbond-Add-support-for-W25N01GV.patch The SPI-NAND framework from Linux uses common driver code that is then "tuned" by a tiny struct of chip-specific data that describes available commands, timing, and layout (data and OOB data). Several manufacturers and chips have been added since 4.19, several of which are used in devices already supported by OpenWrt (typically with no or "legacy" access to their NAND memory). This commit catches up the supported-chip definitions through Linux 5.2-rc6 and linux/next. The driver is only compiled for platforms with CONFIG_MTD_SPI_NAND=y. This presently includes ipq40xx and pistachio, with the addition of ath79-nand in these commits (and not ath79-generic or ath79-tiny). Upstream patches refreshed against 4.19.75 Build-tested-on: ipq40xx Run-tested-on: ath79-nand Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: uboot-envtools: Add GL-AR300M-LiteJeff Kletsky2019-10-241-0/+1
| | | | | | Add the GL.iNet GL-AR300M-Lite to the list of supported boards. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: Refactor GL.iNet GL-AR300M-series generic.mkJeff Kletsky2019-10-241-3/+3
| | | | | | | | | | Rework DEVICE_VENDOR, DEVICE_MODEL, and DEVICE_VARIANT for the GL-AR300M series on the ath79-generic target. Changes GL-AR300M-Lite to the current form with DEVICE_VARIANT := Lite (board name is unchanged) Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: GL-AR750S: Add I2C SupportJeff Kletsky2019-10-241-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | The GL-AR750S has an internal header for I2C. Provide DTS definitions for the i2c-gpio driver. The I2C drivers; kmod-i2c-core, kmod-i2c-gpio consume ~20 kB of flash and can be loaded as modules, Default clock measured ~11.2 ms period, ~89 kHz The board has well-labeled (unpopulated) headers for serial and I2C along the front edge of the board (the edge with the LEDs). Looking from the top, rear of the unit (behind Ethernet jacks) ------------------------------------------- 5G_LED 2G_LED PWR_LED O O O O O O O 3 S S G T R G V C D N X X N 3 L A D D Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: GL-AR300M series: Add I2C SupportJeff Kletsky2019-10-241-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL-AR300M series have an internal header for I2C. Provide DTS definitions for the i2c-gpio driver. The I2C drivers; kmod-i2c-core, kmod-i2c-gpio consume ~20 kB of flash and can be loaded as modules, Default clock measured ~11.4 ms period, ~88 kHz The board has two sets of (unpopulated) headers. While facing the back of the board (looking into the Ethernet jacks), and looking from the top, the one on the left edge of the baord with four holes is the I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards. | (Patch antenna) | | | O GND | O SDA / GPIO 17 | O SCL / GPIO 16 | ⊡ 3V3 (square land) | | (Ethernet jacks) https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states "Note: I2C is not working in some early version of the router." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ramips: add support for Asus RT-AC65PGabor Varga2019-10-246-155/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it. On both routers the installation can be done also via SSH: Note: The user/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt factory image via scp: > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.50.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux 6. Reboot the router > reboot Changelog: v3: removed [] from filename, rebased to latest master v2: Rebased to latest master v1: Initial release Signed-off-by: Gabor Varga <vargagab@gmail.com>
* kernel: netfilter: reuse kconfig and files info from include dirYousong Zhou2019-10-241-23/+9
| | | | | | Less chance of missing out kconfig symbols at least Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* toolchain: gcc: enable sanitizers for glibc toolchainYousong Zhou2019-10-242-1/+176
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* tools: keep stamp file in $(STAGING_DIR_HOST)Yousong Zhou2019-10-241-2/+2
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: add model detection for UniFi AC-LRAndreas Ziegler2019-10-232-0/+9
| | | | | | | | | | | | | | This commit adds correct model detection for UniFi AC-LR. Previously, said device was incorrectly detected as UniFi-AC-LITE/MESH. The Information about the device is stored at 0xC in the EEPROM partition. It corresponds to the sysid in /etc/board.info of the Ubiquiti stock firmware. Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [adjust naming style of target to existing ones] Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for AVM FRITZ!Repeater 1200David Bauer2019-10-239-7/+557
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: add AVM FRITZ!Repeater 1200 bdfDavid Bauer2019-10-232-0/+2
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-fritz4040: update to latest HEADDavid Bauer2019-10-231-3/+3
| | | | | | | | f92be9d add support for AVM FRITZ!Repeater 1200 d651302 enable support for Atheros AR8033 PHY e4c857c add machtype override hack Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add missing backslash in 11-ath10k-caldataDavid Bauer2019-10-231-1/+1
| | | | | | | This adds a missing backslash in the caldata-extraction script. Without this fix, caldata extraction fails for every device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix ethernet probe abort on missing phy-resetDavid Bauer2019-10-231-1/+1
| | | | | | | This commit completely fixes the abortion of the ipq40xx ethernet driver probe in case no phy-reset is defined. Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm63xx: split up DEVICE_TITLEMoritz Warning2019-10-221-91/+219
| | | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Uses DEVICE_ALT* variables for alternative vendor/retailer names. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* procd: update to latest git HEADHans Dedecker2019-10-221-3/+3
| | | | | | 258aa04 procd: Add cached and available to memory table Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* brcm63xx: fix build with GCC 8.3Jonas Gorski2019-10-221-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes the following build error when building when using GCC 8.3: In file included from ./include/linux/string.h:19, from ./include/linux/bitmap.h:9, from ./include/linux/cpumask.h:12, from ./arch/mips/include/asm/processor.h:15, from ./arch/mips/include/asm/thread_info.h:16, from ./include/linux/thread_info.h:38, from ./include/asm-generic/preempt.h:5, from ./arch/mips/include/generated/asm/preempt.h:1, from ./include/linux/preempt.h:81, from ./include/linux/spinlock.h:51, from ./include/linux/mmzone.h:8, from ./include/linux/bootmem.h:8, from arch/mips/bcm63xx/prom.c:10: arch/mips/bcm63xx/prom.c: In function 'prom_init': ./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds] __ret = __builtin_memcpy((dst), (src), __len); \ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy' memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20); ^~~~~~ In file included from arch/mips/bcm63xx/prom.c:14: ./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here extern char bmips_smp_movevec; Reported-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mac80211: fix build of rtw88David Bauer2019-10-221-1/+2
| | | | | | | | | | This commit fixes failing builds because of an incorrect configuration for the kmod-rtw88 package. RTW88_8822BE as well as RTW88_8822CE have to bes selected as "y" even when building the driver as a module. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix LAN/WAN MAC addresses of Xiaomi MiWiFi Mini boardAdrian Schmutzler2019-10-221-3/+1
| | | | | | | | | | | | | | | | | | | Based on stock firmware tests, both LAN and WAN ports use the MAC address from 0x28 on factory partition. In OpenWrt, this one is already set in DTS. This patch removes the local bit set in 02_network previously, and adjusts LAN/WAN addresses as on stock firmware. Note that in tests we found a MAC address in 0x2e that is the one in 0x28 plus 1. Since stock firmware does not use it though, we do not use it either. Thanks to Chih-Wei Chen for testing this on his device. ref: https://github.com/openwrt/openwrt/pull/2497 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: uci-defaults: do config flush in one shotRoman Yeryomin2019-10-221-2/+1
| | | | | | | | | | | Moving a file between tmpfs and other fs is neither faster nor safer, thus no point in doing it in two steps. Use new jshn option to write output directly to file. Originally discussed here: http://lists.openwrt.org/pipermail/openwrt-devel/2017-December/010127.html Signed-off-by: Roman Yeryomin <roman@advem.lv>
* libubox: update to latest git HEADRoman Yeryomin2019-10-221-3/+3
| | | | | | eb30a03 libubox, jshn: add option to write output to a file Signed-off-by: Roman Yeryomin <roman@advem.lv>
* firmware: add Realtek RTL8822BE/RTL8822CE firmwareDavid Bauer2019-10-221-0/+15
| | | | | | | This commit adds packages for the Realtek RTl8822BE/RTL8822CE firmware to be used with the rtw88 driver. Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: add rtw88 driverDavid Bauer2019-10-221-1/+12
| | | | | | | | | This commits adds packaging for the new RTW88 driver from Realtek. It supports the Realtek 8822BE/8822CE PCIe wireless chips. For operation, the complementary firmware has to be loaded. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix optional gpio-resetJohn Crispin2019-10-221-1/+1
| | | | | | If a gpio reset pin was not defined we should not bog out. Signed-off-by: John Crispin <john@phrozen.org>
* urngd: update to latest Git headPetr Štetiar2019-10-211-4/+4
| | | | | | | | | * 40f939d57c67 Tag version 1.0.1 * 9e758e6e6aec jitterentropy-rngd: update to version v1.1.0 + clang compile fix * 193586a25adc Fix wrong types in format strings used in debug build * d474977bb611 Add initial GitLab CI support Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: improve support for TP-Link CPE510 v2Adrian Schmutzler2019-10-218-33/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") where the support for this device wasn't optimal. Device support for the CPE510v2 so far has been a hack to enable flashing with CPE510v1 images. Those even have different hardware (e.g. additional ethernet port). With this patch, we provide proper support for this device in ar71xx. Installation: - Flash factory image through stock firmware WEB UI or through TFTP - To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. - Rename factory image to recovery.bin - Stock TFTP server IP: 192.168.0.100 - Stock device TFTP address: 192.168.0.254 Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net> [Rebased onto revert commit, changed comments in mach-cpe510.c, changed commit title and description, fixed eth0 MAC address, removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix TARGET_DEVICES after UniElec renameAdrian Schmutzler2019-10-212-3/+3
| | | | | | | | | | Device node names were updated, but updating TARGET_DEVICES was overlooked. Fixes: 4408723d42e0 ("ramips: remove RAM size from device name for UniElec devices") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "build: separate signing logic"John Crispin2019-10-213-27/+15
| | | | | | | | This reverts commit 4a45e69d190f72ed94878487b271ed7651dd9efa. This broke the buildbots Signed-off-by: John Crispin <john@phrozen.org>
* ramips: remove RAM size from device name for UniElec devicesAdrian Schmutzler2019-10-217-18/+19
| | | | | | | | | | | UniElec devices are the last ones in ramips target still having the RAM size in device name although RAM size is auto-detected. Remove this from device name, compatible, etc., as it's not required and might be misleading to users and developers adding device support copying those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: base-files: disable sysupgrade for routerstations and ja76pf2Tomasz Maciej Nowak2019-10-211-2/+2
| | | | | | | | | | Previous commit 0cc87b3 "ath79: image: disable sysupgrade images for routerstations and ja76pf2" doesn't remedy completely the posibility of bricking the device, since user could try to downgrade with an older image. Therefore disable sysupgrade code for these boards with a small note. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: apply alphabetical sorting to entries in 10_fix_wifi_macAdrian Schmutzler2019-10-211-4/+4
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove empty default case in 10_fix_wifi_macAdrian Schmutzler2019-10-211-2/+0
| | | | | | This removes a useless empty default case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix whitespaces in 10_fix_wifi_macAdrian Schmutzler2019-10-211-8/+7
| | | | | | | This converts leading whitespaces to tabs and removes a double newline at the end of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt762x: convert devices to interrupt-driven gpio-keysAdrian Schmutzler2019-10-21161-314/+197
| | | | | | | | | | | This converts all remaining devices to use interrupt-driven gpio-keys compatible instead of gpio-keys-polled. The poll-interval is removed. While at it, add/remove newlines in keys and leds node where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: call Host/Uninstall before wiping the host build dirAndre Heider2019-10-211-1/+1
| | | | | | | Uninstall targets may depend on build artefacts, like `make uninstall` or `ninja uninstall`. Signed-off-by: Andre Heider <a.heider@gmail.com>
* ath79: add LED migration for several Archer Cxx devicesAdrian Schmutzler2019-10-211-3/+9
| | | | | | | | | Several Archer Cxx devices were using board-specific LED names in ar71xx, which were changed to "tp-link:*" in ath79. This patch adds migration for them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use board name in LED migrationsAdrian Schmutzler2019-10-211-4/+3
| | | | | | | | | | | | | Several devices added to LED migration script will just have their (old) board name converted to tp-link. By using a variable for this, the amount of code in the migration script can be reduced and the chance for typos is reduced. This patch also introduces the marker for beginning of a pattern "^" to the regex, so the match is more specific. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 20:27:11 +0000