aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.104Koen Vandeputte2019-03-0537-278/+275
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 332-arc-add-OWRTDTB-section.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.161Koen Vandeputte2019-03-059-36/+36
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 332-arc-add-OWRTDTB-section.patch Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mac80211: rt2x00: do not increment sequence number while re-transmittingVijayakumar Durai2019-03-051-0/+55
| | | | | | | | | | | Currently STA+AP re-transmitting the management frames with incremented sequence number if hardware is assigning the sequence. Fix is to assign the sequence number for Beacon by hardware and for other Management frames software will assign the sequence number Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
* ath79: Add support for Ubiquiti Nanostation M (XW)Petr Štetiar2019-03-054-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: gmac: ar934x: Add parser for mii-gmac0-slavePetr Štetiar2019-03-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | While converting Nanostation M XW from current ar71xx code to ath79 I've hit one issue, where the ethernet networking wasn't working, so I was checking every bit in the networking setup path between ar71xx and ath79. I've came to the following code in ar71xx/mach-ubnt-xm.c: static void __init ubnt_xw_init(void) { ... ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_MII_GMAC0 | AR934X_ETH_CFG_MII_GMAC0_SLAVE); ... } Where this code is setting AR934X_ETH_CFG_MII_GMAC0_SLAVE bit in AR934X_GMAC_REG_ETH_CFG register, but I couldn't find a way of setting this bit from DTS, so this patch adds `mii-gmac0-slave` DTS property which allows setting of this bit in `gmac-config`, which is then used in Nanostation M XW DTS. Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: qca955x: assert mdio/gmac reset togetherChuanhong Guo2019-03-051-10/+8
| | | | | | | | This allows resetting gmac registers during initialization. Also add compatible string for qca955x mdio to enable more mdio clock dividers. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar934x: assert mac/mdio reset together for gmac0Chuanhong Guo2019-03-051-6/+3
| | | | | | This allows resetting gmac registers during initialization. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: add support for optional mdio resetChuanhong Guo2019-03-052-1/+8
| | | | | | | | | | | | | | | | | | | | | | On ar933x and later chips, there are separated mac/mdio resets, but resetting the entire gmac block with register values requires both mac_reset and mdio_reset to be asserted together. Add support for optional mdio reset so that we can do a full reset if needed. This patch also replaced deprecated devm_reset_control_get for mac reset. To use this feature, the following is needed: 1. drop "simple-mfd" compatible to register mdio0 after gmac init so that mdio registers aren't reset after initialization. 2. move mdio reset from mdio-bus to its parent eth node. NOTE: This can't be applied on gmac1 with builtin switch since we haven't add a feature to defer probe if phy connection failed. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: register mdio using of_platform_populateChuanhong Guo2019-03-051-5/+12
| | | | | | | remove the hacky checking of "simple-mfd" compatible also add some comments explaining that piece of code. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx-mdio: get reset control using devm apiChuanhong Guo2019-03-051-1/+1
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdevChuanhong Guo2019-03-051-22/+11
| | | | | | | | using the devm api makes the code simpler. also drop unneeded memory free from ag71xx_remove since they are allocated using devm apis. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()Chuanhong Guo2019-03-051-22/+2
| | | | | | | | | phy_modes() in phy.h can convert PHY modes to string with supports for all available PHY modes. Also add a space in mode printing to make it look better. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* oxnas: pcie: model shared resource as external pcie-phy driverDaniel Golle2019-03-046-77/+226
| | | | | | | Refactor pcie-oxnas to have shared resources in syscon and new pcie-phy driver. Hopefully this revives PCIe... Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: convert pcie to builtin_platform_driverDaniel Golle2019-03-041-21/+12
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: restart: use register definitions from dt-bindingsDaniel Golle2019-03-031-60/+27
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: cleanup and improve pcie driverDaniel Golle2019-03-031-274/+45
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* tools: squashfskit4 should only depend on coreutils on non-linux systemsFelix Fietkau2019-03-031-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/squashfskit: fix version detection on non-linux systemAlexander Couzens2019-03-032-1/+22
| | | | | | | | | | | | gnu date is present in our staging_dir which means squashfskit will fail to build. Prevent also a race condition if coreutils is build after squashfskit. To prevent a race condition, depend on coreutils. Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* mt76: update to the latest versionFelix Fietkau2019-03-031-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | 3c6df9b mt76: rewrite dma descriptor base and ring size on queue reset 30e757e mt76: mt76x02: when setting a key, use PN from mac80211 fa83406 mt76: mt76x2: implement full device restart on watchdog reset ead881b mt76: mt76x02: do not sync PN for keys with sw_iv set ba1d989 mt76: mmio: move mt76x02_set_irq_mask in mt76 module 283ebbe mt76: dma: move mt76x02_init_{tx,rx}_queue in mt76 module b216d3c mt76: introduce q->stopped parameter 8b437d2 mt76x02: clear sta and vif driver data structures on add 2c62d03 mt76x02: clear running flag when resetting state on restart 6b10cfc mt76: mt76x02: only update the base mac address if necessary 669bc49 mt76: mt76x02: reduce false positives in ED/CCA tx blocking 2ed9382 mt76: mt7603: fix tx status HT rate validation d2c6823 mt76: mt76x2: fix external LNA gain settings 8ee2259 mt76: mt76x2: fix 2.4 GHz channel gain settings 8bfe6d4 mt76: mt7603: clear ps filtering mode before releasing buffered frames d13b065 mt76: mt7603: fix up hardware queue index for PS filtered packets eb1ecc4 mt76: mt7603: notify mac80211 about buffered frames in ps queue 3687eec mt76: mt7603: clear the service period on releasing PS filtered packets 42ab27e mt76: when releasing PS frames, end the service period if no frame was found 461f3b0 mt76: mt76x02: disable ED/CCA by default Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: Activate DRIVER_11W_SUPPORT for more capable driversHauke Mehrtens2019-03-036-9/+9
| | | | | | | | | | ieee80211w support is only activated in hostapd when at least one capable driver is build into the image. Many drivers which are capable of ieee80211 (MFP) and have the MFP_CAPABLE set in the driver are still missing the DRIVER_11W_SUPPORT dependency. Add this to more driver capable of ieee80211w. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* oxnas: add SoC restart driver for rebootDaniel Golle2019-03-033-23/+298
| | | | | | Refresh oxnas kernel config while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ltq-vdsl-fw: update download URLDaniel Golle2019-03-023-6/+6
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: cloudengines,pogoplug*: enable USB portsDaniel Golle2019-03-022-0/+17
| | | | | Reported-by: Jörg Fischer <fischer.loepsingen@yahoo.de> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mpc85xx: Fix Aerohive HiveAP-330 initramfs imageChris Blake2019-03-021-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At some point our initramfs image grew over 6MB, which is causing an issue when uncompressing in the stock bootloader: => bootm 0x5000000 - 0x1000000; Image Name: Linux-4.19.24 Created: 2019-02-23 1:58:20 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 6752470 Bytes = 6.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Booting using the fdt blob at 0x1000000 Uncompressing Kernel Image ... Error: inflate() returned -5 GUNZIP: uncompress, out-of-mem or overwrite error - must RESET board to recover Loading Device Tree to 00ffa000, end 00fffc78 ... OK To get around this, we need to move to an uncompressed image for the initramfs image. While this makes a larger image, it is thankfully bootable so people can then convert their devices to run OpenWRT. It's worth noting the non-initramfs image is under 3M, so it will be ages before we have any issues with the flashed kernel. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [keep commit message at less than 75 characters per line]
* ath79: make TP-Link revision naming consistentDavid Bauer2019-03-029-9/+9
| | | | | | | | This commit makes the TP-Link hardware-revision naming consistent to match the one used by the vendor. TP-Link refers to the different revisions as "vX" not "Version X". Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Belkin F9K1109v1Kip Porterfield2019-03-025-0/+193
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz - RAM: 64Mb - Flash: 8MB (SPI-NOR) - Ethernet: 10/100/1000 Mbps - WLAN Wireless 1: SoC-integrated : 2.4/5 GHz Wireless 2: 2.4 GHz RT3092L - LED: 2x USB, WAN, LAN - Key: WPS, reset - Serial: 4-pin header, (57600,8,N,1), 3.3V TTL, GND, RX, TX, V - J12 marking on board - USB ports: 2 x USB 2.0 Flashing instructions: Option 1 (from bootloader web) - Hold reset button on the back of router when plugging in power (for at-least 10 seconds after plugged in) - Connect to a Lan port - Set computer IP to 10.10.10.3 - Go to http://10.10.10.123 in a web browser - Click the Browse... Button and select the *squashfs.sysupgrade.bin file then click APPLY Option 2 (from the stock admin web) - Go to firmware upgrade - Upload the **factory** image *initramfs.bin first - Boot into openwrt - From Luci web in openwrt upload the *squashfs.sysupgrade.bin Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added v1 to the compatible identifier, added pciid for the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi to prepare for a possible F9K1103 patch]
* ath79: TP-Link Archer C7 v4 swap usb led namesDavid Santamaría Rogado2019-03-021-2/+2
| | | | | | | | | | | | | | | | Commit 34b10b46 made usb match with the corresponding usb label. The problem is that v4 seems to use in stock firmware the upper led for usb 1 and the lower led for usb 2. The led assigned varies between TP-Link models and even same model versions. For example, Archer C7 v1 and v2 have the leds in the reverse order. Revert 34b10b46 and swap led labels instead, now usb port and led label match and also respect the original behavior. Tested-by: Oldrich Jedlicka <oldium.pro@gmail.com> Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* layerscape: fix VFIO driver build issue since linux-4.14.99Yangbo Lu2019-03-021-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The linux-4.14.99 had introduced below upstream patch. 6636dc5e01c6 arm64: io: Ensure value passed to __iormb() is held in a 64-bit register It was causing VFIO driver build issue. This patch is to fix it. CC drivers/vfio/fsl-mc/vfio_fsl_mc.o In file included from ./include/linux/scatterlist.h:9:0, from ./include/linux/iommu.h:22, from drivers/vfio/fsl-mc/vfio_fsl_mc.c:14: drivers/vfio/fsl-mc/vfio_fsl_mc.c: In function 'vfio_fsl_mc_dprc_wait_for_response': ./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token : "=r" (tmp) : "r" ((unsigned long)(v)) \ ^ drivers/vfio/fsl-mc/vfio_fsl_mc.c:334:3: note: in expansion of macro '__iormb' __iormb(); ^~~~~~~ ./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token : "=r" (tmp) : "r" ((unsigned long)(v)) \ ^ drivers/vfio/fsl-mc/vfio_fsl_mc.c:336:3: note: in expansion of macro '__iormb' __iormb(); ^~~~~~~ Reported-by: Mathew McBride <matt@traverse.com.au> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* apm821xx: speed up ath9k-caldata extractionChristian Lamparter2019-03-021-2/+2
| | | | | | | | | | | | Reading and writing to and from flash storage is slow and currently, the ath10kcal_extract() scripts are even more at an disadvantage because they use a block size of 1 to be able skip. This patch reworks the extraction scripts to be much faster and efficient by reading and writing the calibration data in possibly one big block. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: speed up ath9k-eeprom extractionDmitry Tunin2019-03-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This is a simple copy of ipq40xx: speed up ath10k-caldata extraction commit a69e101ed1169f562fc030a783cd997d3f066b16 Tested on DIR-825-B1 3768+0 records in 3768+0 records out real 0m 11.90s user 0m 0.03s sys 0m 9.94s 1+0 records in 1+0 records out real 0m 0.03s user 0m 0.00s sys 0m 0.03s With this change eeprom extraction is fast enough to get working Wi-Fi after initial install. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* x86: fix geode image builds reduxChristian Lamparter2019-03-022-1/+14
| | | | | | | | | | | | | | | | | This patch adds more disabled DRM config symbols from the x86' config to the generic target configs. The existing symbols in the x86' configs are kept for now, until we know whenever we want to remove such symbols or not (see Github PR #1831, #1825, #1828). THis patch also contains a squashed patch from Daniel Engberg <daniel.engberg.lists@pyret.net> titled "kernel: Fix config for 4.14" which fixes a duplicated line added by: commit 8bdc241d01eb ("x86: fix geode image builds") Fixes: 8bdc241d01eb ("x86: fix geode image builds") Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* oxnas: switch to DTS aliases for LEDs and use generic diag.shDaniel Golle2019-03-017-75/+58
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* iwinfo: update to latest gitDaniel Golle2019-03-011-3/+3
| | | | | | | | b514490 iwinfo: add device id for MediaTek MT7603E e9e1400 iwinfo: more Ralink and MediaTek WiSoC and PCIe chips cb108c5 iwinfo: fix capitalization of vendor name Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: fix forgotten MTD partition nameDaniel Golle2019-03-011-2/+2
| | | | | Fixes: 858aebc0ef ("oxnas: unify MTD partition names") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: add a fix to prevent unsafe queue wake calls during restartFelix Fietkau2019-03-011-0/+33
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: backport tx queue start/stop fixFelix Fietkau2019-03-016-15/+287
| | | | | | Among other things, it fixes a race condition on calling ieee80211_restart_hw Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: bump to version 2019-02-27Yousong Zhou2019-03-011-4/+4
| | | | | | | | | | Contains the following change eeef7b5 blobmsg_json: blobmsg_format_string: do not escape '/' Resolves FS#2147 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* busybox: sync Config.in filesYousong Zhou2019-03-0125-825/+1225
| | | | | | | | | | | | | | The change was made with the following commands cd package/utils/busybox/config ../convert_menuconfig.pl ~/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/busybox-1.30.1 convert_defaults.pl has no changes other than overwriting defaults for BUSYBOX_DEFAULT_FEATURE_IPV6 Resolves FS#2146 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* busybox: unindent busybox Config.inYousong Zhou2019-03-0124-2267/+2267
| | | | | | | | | | | | | This is to align with upstream change 72089cf ("config: deindent all help texts") and to make the follow-up change syncing Config.in files with current busybox version more reviewable It was made with the following commands cd package/utils/busybox/config find . -name 'Config.in' | xargs sed -ir -e 's/^\t \([^ ]\)/\t\1/' Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ath79: Fix indentAdrian Schmutzler2019-03-011-1/+1
| | | | | | Fix wrong indentation introduced in 59c2f8a. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: rt2x00: cleanup ePA, RXIQ and TX-LOFT codeDaniel Golle2019-03-014-230/+84
| | | | | | | | | | consolidate patch 651-rt2x00-remove-unneccesary-code.patch. fixup the most obvious whitespace problems in RXIQ and TX-LOFT code. always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid compiler warning about them being potentially uninitialized. no functional changes (intended) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: rt2x00: patch tracking cosmeticsDaniel Golle2019-03-019-0/+27
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: remove uboot-oxnas-ox820 from default package selectionDaniel Golle2019-03-011-4/+0
| | | | | | | | All supported boards should work with the $vendor bootloader just fine. Existing users should mindfully re-flash using new initramfs build and restore $vendor bootloader's bootcmd to it's original setting. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: switch to kmod-ledtrig-usb-portDaniel Golle2019-03-015-7/+20
| | | | | | | | Add port handles for both USB 2.0 ports so they can be used as trigger-source for USB LEDs. Suggestions for pogoplug and akitio,mycloud devices are welcome. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: oxnas: sync with current oxnas/ox820 DTSDaniel Golle2019-03-011-5/+4
| | | | | | | | | Use tested values on shuttle,kd20 and assumed values for mitrastar,stg-212 and cloudengines,pogoplug*. akitio users have yet to report back stock flash layout to support vendor bootloader environment there as well. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: unify MTD partition namesDaniel Golle2019-03-014-8/+13
| | | | | | | Use 'u-boot' and 'u-boot-env' like the majority of OpenWrt targets does... Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* package/ncurses: change AR options to fix reproducible buildsAlexander Couzens2019-02-282-1/+23
| | | | | | | | | | ar has a deterministic (-D) and non-deterministic (-U) mode. OpenWrt is already using the deterministic mode by default, but ncurses' configure script force this to be non-deterministic. Since autoreconf fails to generate a new configure, the configure script is directly modified. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* include/kernel: sort autoload modules list to fix reproducible buildsAlexander Couzens2019-02-281-1/+1
| | | | | | | | When autoloading more than one modules per packages, /etc/modules.d/$module depends on the file system ordering. To test this: use disorderfs on the build_dir and build kmod-sched. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* oxnas: add missing NAND partitionsDaniel Golle2019-02-283-4/+68
| | | | | | | | | | | | | | | | add kernel and other missing NAND flash partitions to allow booting using stock loader instead of the 2nd-stage bootloader. This will ease installation from stock firmware on pogoplugs as well as stg212 aka. medion nas. Existing users of OpenWrt on those boards will have to boot initramfs generated after this commit and subsequently flash first the ubinized image, then again run initramfs to flash sysupgrade.tar image, and then restore bootcmd in U-Boot environment back to the original setting ('nboot 60500000 0 440000' or something like that) instead of jumping into the now no longer used 2nd-stage loader. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq806x: fix LED configuration for NEC Aterm WG2600HPINAGAKI Hiroshi2019-02-281-1/+1
| | | | | | | NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should be used as a portmask instead of "0x1e" for "WAN" LED configuration. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-12 15:51:30 +0000