aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* hostapd: enable CTRL_IFACE_MIB for hostapd-fullDavid Bauer2019-12-087-0/+35
| | | | | | | | This enables the CTRL_IFACE_MIB symbol for wpad-full and hostapd-full. If it is not enabled, statistic outputs such as "hostapd_cli all_sta" are empty. Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm47xx: add switch configuration for WNR3500LOlli Asikainen2019-12-081-1/+2
| | | | | | | | | | | | | | | | | | | | Netgear WNR3500L is an already supported device, but out of the box, the device has no switch configuration and there is no wan. The correct configuration for this specific model is similar to some other models. This simple commit adds the correct switch and the out-of-the-box experience is improved. Experimentally determined: Port 0 => WAN Port 1..4 => LAN Port 5..7 => unused Port 8 => CPU Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com> Tested-by: Fabian Zaremba <fabian@youremail.eu> [added port mapping to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: convert mediatek,mtd-eeprom from decimal to hex notationAdrian Schmutzler2019-12-083-6/+6
| | | | | | | | | | A small subset of devices uses decimal notation for mediatek,mtd-eeprom in DTS files. Convert to hexadecimal notation to be consistent with all the rest. Also change "0" to "0x0" in the same files for consistency. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix number of LAN Ports for Mikrotik RBM33GMartin Schiller2019-12-081-1/+4
| | | | | | | | The Mikrotik RBM33G has only 2 LAN ports. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [moved node in 02_network to maintain alphabetic sorting] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix switch port order for TP-Link Archer C20iWalter Sonius2019-12-081-1/+1
| | | | | | | | | | | | | | | | | | Physical port order watched from the backside of the C20i (from left to right) is: Internet / 1 / 2 / 3 / 4 Physical Port Switch port WAN 0 LAN 3 1 LAN 4 2 LAN 1 3 LAN 2 4 (not used) 5 CPU 6 Signed-off-by: Walter Sonius <walterav1984@gmail.com> [commit message/title improvements] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix WNDR3700/WNDR3800 wifi reg sizeChristian Lamparter2019-12-071-2/+2
| | | | | | | | "[...] the size component shall be zero." (See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1" section "4.1.1 Open Firmware-defined Properties for Child Nodes") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* iproute2: update to 5.4.0Hans Dedecker2019-12-063-7/+7
| | | | | | | Update iproute2 to latest stable version, see https://lwn.net/Articles/805654/ for the changes in 5.4.0 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mediatek: fix pcie bringup issueJohn Crispin2019-12-051-0/+9
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* wireguard: bump to 0.0.20191205Jason A. Donenfeld2019-12-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * wg-quick: linux: suppress error when finding unused table This fixes a spurious warning messages seen with recent versions of iproute2 and kernels. * wg-quick: linux: ensure postdown hooks execute * wg-quick: linux: have remove_iptables return true * wg-quick: linux: iptables-* -w is not widely supported Adding in iptables had some hiccups. For the record, I'm very unhappy about having to put any firewalling code into wg-quick(8). We'll of course need to support nftables too at some point if this continues. I'm investigating with upstream the possibility of adding a sysctl to patch the issue that iptables is handling now, so hopefully at somepoint down the line we'll be able to shed this dependency once again. * send: use kfree_skb_list * device: prepare skb_list_walk_safe for upstreaming * send: avoid touching skb->{next,prev} directly Suggestions from LKML. * ipc: make sure userspace communication frees wgdevice Free things properly on error paths. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* ath79: add support for Ubiquiti LiteBeam AC Gen2Stijn Tintel2019-12-044-0/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: drop IMAGE/factory.bin from ubnt-wa devicesStijn Tintel2019-12-041-4/+0
| | | | | | | | | | The sysupgrade image contains OpenWrt specific metadata. Having this metadata in the factory images makes no sense. Drop IMAGE/factory.bin from Device/ubnt-wa and use the default from Device/ubnt instead. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: act_ctinfo: fix updated backport on 4.14Kevin Darbyshire-Bryant2019-12-041-21/+8
| | | | | | | | It turns out my 4.14 testing had a rather large flaw in it and the 'extack' mechanism isn't quite ready. Remove the extack stuff from this backport. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: act_ctinfo: update backportKevin Darbyshire-Bryant2019-12-032-72/+210
| | | | | | | | | | Since the original backports from kernel 5.3 a few things have been tweaked by kernel bumps & other upstream changes. Update the backport to reflect upstream as closely as possible and remove the bitrot. Functions remain the same, error reporting improved. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: fix source of label MAC address for Ubiquiti XM devicesAdrian Schmutzler2019-12-031-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In d421a8b94489 ("ath79: read label MAC address from flash instead of using phy0/phy1") the source of the label MAC address was changed for devices just reading it from phy0. To get rid of the dependency from phy startup, addresses were read directly from the flash locations that are used to initialize the phy MAC addresses. Unfortunately, it turned out that Ubiquiti XM devices seem to have different flash locations than expected, and also seem to have specific locations for different devices (all in art/EEPROM): 0xe012 AR9280 Nanostation M2 - 0x120c 0xe035 AR9280 Nanostation M3 - 0x120c 0xe1b2 AR9280 Rocket M2 - 0x120c 0xe1c3 AR9280 Rocket M3 - 0x120c 0xe1b5 AR9280 Rocket M5 - 0x120c 0xe2d5 AR9280 Bullet M2 Titanium - 0x120c 0xe2b5 AR9280 Nanobridge M5 - 0x120c 0xe202 AR9280 Bullet M2 - 0x120c 0xe232 AR9287 Nanobridge M2 - 0x110c 0xe4a2 AR9285 AirRouter - 0xa0bf Picostation M2 - 0x120c and 0xa0bf Nanostation Loco M2 - not in 0x120c, other locations not checked An additional problem of the Ubiquiti device support in OpenWrt is that we provide images that match several subvariants of the devices, which might have different MAC address locations. Given that reading the address from phy0 in 02_network _is_ working for the ath79 target in general, it does not seem reasonable to rebuild a complex MAC address retrieval mechanism which is already present in the ath9k driver. So, this patch reverts the label MAC address source for Ubiquiti XM devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress. This doesn't affect XW and Unifi AC devices, where the label MAC address source is defined via device tree. For alfa-network,ap121f the location 0x1002 is kept, as this has been verified during device support preparation in PR #2199. Fixes: d421a8b94489 ("ath79: read label MAC address from flash instead of using phy0/phy1") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* gre: add ipv6 parameter to gre interfacesAlin Nastac2019-12-022-3/+5
| | | | | | | | | IPv6 protocol is enabled on all gre interfaces, but gre(v6)tap interfaces are usually added to a bridge interface, in which case IPv6 should be enabled only on the bridge interface. Signed-off-by: Alin Nastac <alin.nastac@gmail.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
* curl: bump to 7.67.0Hans Dedecker2019-12-021-2/+2
| | | | | | For changes in 7.67.0; see https://curl.haxx.se/changes.html#7_67_0 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* octeon: fix sysupgradeStijn Tintel2019-11-301-2/+2
| | | | | | | | Sysupgrade was failing due to incorrect replacement of backticks: /sbin/sysupgrade: /lib/upgrade/platform.sh: line 101: syntax error: missing '))' Fixes: 0bbfc3dff719 ("octeon: replace backticks by $(...)") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* generic ar8xxx: increase VLAN table for AR83x7David Bauer2019-11-303-9/+13
| | | | | | | | | | | | The Atheros AR8327 and AR8337 have (according to their datasheet) a VLAN table with a maximum of 4096 entries. Currently, there's a hard limit of 128 VLANs, which is the same as for most other Atheros switches. Increase this limit only for the AR83x7 series and modify some shared functions to allow them to work with a variable max VLAN count. Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: switch to upstream owl-loader driverChristian Lamparter2019-11-308-424/+112
| | | | | | | | | | | | | | | | | | The Owl Loader (named after the codename that Atheros gave these devices back in the day) has been accepted upstream. This patch removes the "misc" driver OpenWrt had and adds the remaining differences against the version that ships with 5.4-rc1 into a separate "120-owl-loader-compat.patch" file that can be cut down once AR71XX is being dealt with. Note: I decided to keep the existing (kmod-)owl-loader package name around for now. The kernel module file in the kmod package will be called ath9k_pci_owl_loader.ko though. Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* busybox: add glibc dependency for vi regex optionSatadru Pramanik2019-11-301-1/+2
| | | | | | | | | | | | | | | | | | Build with musl libc fails with BUSYBOX_DEFAULT_FEATURE_VI_REGEX_SEARCH enabled. Enabling BusyBox's vi regex search option depends upon GNU regex. Musl libc does not support GNU regex[1]. So this patch adds explicit dependency on GNU libc and while at it remove the FIXME comment. 1. https://wiki.musl-libc.org/functional-differences-from-glibc.html Ref: https://dev.archive.openwrt.org/ticket/21741.html Ref: https://forum.openwrt.org/t/busybox-not-compiling/ Ref: https://github.com/openwrt/packages/issues/4453 Signed-off-by: Satadru Pramanik <satadru@umich.edu> [commit subject/description tweaks, From: fix, USE_GLIBC fix, removed comments] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* glibc: backport fix for regexec buffer read overrunAlin Nastac2019-11-301-0/+26
| | | | | | | | | | | | | | | | | | | Problem found by AddressSanitizer[1]: Latest `grep` (git commit 1019e6e) compiled with asan may cause a heap-buffer-overflow when `-i` is specified. ./grep -i '\(\(\)*.\)*\(\)\(\)\1' /bin/chvt ================================================================= ==16206==ERROR: AddressSanitizer: heap-buffer-overflow on address 1. https://debbugs.gnu.org/34140 Ref: https://sourceware.org/bugzilla/show_bug.cgi?id=24114 Signed-off-by: Alin Nastac <alin.nastac@gmail.com> [commit title and description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "mt76: probe load mt7615 driver asynchronously"DENG Qingfang2019-11-301-1/+0
| | | | | | | | | | | | | This reverts commit 81764319637f ("mt76: probe load mt7615 driver asynchronously"). After said commit, users report that MT7615 no longer works on boot and they have to manually enable WiFi (via command "wifi") to make it working again. Fixes: FS#2546 Ref: https://forum.openwrt.org/t/xiaomi-r3p-no-wifi-on-boot/45509 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [commit description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: add support for Crisis Innovation Lab MeshPoint.OneRobert Marko2019-11-307-4/+110
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon Jalapeno module from 8Devices). MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and smart city gateway that can be installed and powered from street lighting (even solar power in the future). MeshPoint provides up to 27 hours of interrupted Wi-Fi and IoT services from internal battery even when external power is not available. MeshPoint.One can be used for disaster relief efforts in order to provide instant Wi-Fi coverage that can be easily expanded by just adding more devices that create wide area mesh network. MeshPoint.One devices have standard Luci UI for management. Features: - 1x 1Gpbs WAN - 1x 1Gbps LAN - POE input (eth0) - POE output (eth1) - Sensor for temperature, humidity and pressure (Bosch BME280) - current, voltage and power measurement via TI INA230 - Hardware real time clock - optional power via Li-Ion battery - micro USB port with USB to serial chip for easy OpenWrt terminal access - I2C header for connecting additional sensors Installation: ------------- Simply flash the sysupgrade image from stock firmware. Or use the built in Web recovery into bootloader: Hold Reset button for 5 to 20 seconds or use UART and httpd command. Web UI will appear on 192.168.2.100 by default. For web recovery use the factory.ubi image. Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr> Signed-off-by: Damir Franusic <damir.franusic@sartura.hr> Signed-off-by: Valent Turkovic <valent@meshpoint.me> Signed-off-by: Robert Marko <robert@meshpoint.me> [commit description long line wrap, usb->USB] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: use DTSI for JalapenoRobert Marko2019-11-302-260/+272
| | | | | | | | | | | | Lets move common code for Jalapeno into DTSI, this way Jalapeno based boards don't introduce duplicate code. While at it, lets also fix some style issues and update to current DTS style. Signed-off-by: Robert Marko <robert@meshpoint.me> [commit description long line wrap] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* netifd: update to latest git HEADHans Dedecker2019-11-291-3/+3
| | | | | | e45b140 interface: warn if ip6hint is truncated Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mac80211: unify setup of iw htmode for mesh and adhocSantiago Piccinini2019-11-291-49/+16
| | | | | | | | | This also fixes mac80211_prepare_vif iw set channel in monitor or mesh mode. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: fixed commit message]
* kernel: bump 4.9 to 4.9.205Koen Vandeputte2019-11-293-7/+7
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-18660 Compile-tested on: none Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.86Koen Vandeputte2019-11-2917-225/+46
| | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch - 0005-mtd-physmap_of-Move-custom-initialization.patch Remove upstreamed: - 0001-pinctrl-gemini-Mask-and-set-properly.patch - 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.156Koen Vandeputte2019-11-2924-63/+63
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ucert: update to latest git HEADDaniel Golle2019-11-291-3/+3
| | | | | | | | | | | | e4bd927 cast ucert_argv to proper type when passing to execv Fixes warnings: warning: passing argument 2 of 'execv' from incompatible pointer type [-Wincompatible-pointer-types] 254 | execv(usign_argv[0], usign_argv) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* config: kernel: fix typo in HFSPLUG_FS_POSIX_ACLStijn Tintel2019-11-281-1/+1
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mpc85xx: add vendor to Makefile node name, derive SUPPORTED_DEVICESAdrian Schmutzler2019-11-271-15/+13
| | | | | | | | | | | | | | By adding the vendor to the Makefile device definition node name, one can derive the standard compatible used in SUPPORTED_DEVICES instead of having to specify it manually. Despite, this moves the naming scheme closer to what is used for other targets (ath79, ramips). Build-tested on all subtargets. Run-tested on TP-Link TL-WDR4900 v1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools: tplink-safeloader: fix whitespace issuesAdrian Schmutzler2019-11-271-42/+42
| | | | | | | | | This replaces tabs by spaces when preceding an equal sign. This improves consistency in the file and makes the indent look correct on all platforms. While at it, also fix one case of inconsistent leading spaces. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)Anderson Vulczak2019-11-278-121/+308
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename EEPROM to artAdrian Schmutzler2019-11-2711-33/+31
| | | | | | | | | | | | | This renames all remaining occurrences of "EEPROM" to "art" to further harmonize the partition labelling in ath79. This will help to reduce the amount of user-space code and might be beneficial when code is copy/pasted in the future. Affected are only devices from Ubiquiti, where the XM board is already using "art" in ath79. Acked-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* wireguard: bump to 0.0.20191127Jason A. Donenfeld2019-11-271-2/+2
| | | | | | | | | | * messages: recalculate rekey max based on a one minute flood * allowedips: safely dereference rcu roots * socket: remove redundant check of new4 * allowedips: avoid double lock in selftest error case * tools: add syncconf command Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* procd: update to latest git HEADHans Dedecker2019-11-261-3/+3
| | | | | | 3aa051b system: sysupgrade: close input side of pipe before reading Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* uboot-envtools: ath79: add support for YunCore XD4200 and A782Piotr Dymacz2019-11-251-1/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for YunCore XD4200 and A782Piotr Dymacz2019-11-256-1/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based (QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE (802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller version of the XD4200, with similar specification but lower TX power. Specification: - QCA9563 (775 MHz) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN) - Wi-Fi 2.4 GHz: - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11) - Wi-Fi 5 GHz: - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11) - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11) - LEDs: - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet) - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet) - 1x button (reset) - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x DC jack (12 V) Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for YunCore TFTP image generationVincent Wiemann2019-11-252-0/+15
| | | | | | | | | | | | | | | | | | YunCore QCA9k based devices released in 2019 require a custom TFTP image for U-Boot built-in recovery mode (triggered with reset button). Image has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI commands which will be executed later. Images without the custom header will be ignored by U-Boot. To be able to support both the vendor firmware (QSDK) and OpenWrt flash layouts, used here commands change the 'bootcmd' before flashing image. This commit adds generic helper script for YunCore devices with 16 MB of flash and enables TFTP image generation for A770 model. Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com> [pepe2k@gmail.com: commit description reworded, recipe renamed] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: generic: base-files: fix indentation in 02_networkPiotr Dymacz2019-11-251-2/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* tools/expat: change package source to GitHubDavid Bauer2019-11-241-1/+1
| | | | | | | According to the SourceForge page, the project is migrating to GitHub. Thus, change the source of the package to GitHub. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: reorganize NETGEAR sercomm boardsDavid Bauer2019-11-245-65/+126
| | | | | | | | | | | | This re-organizes the device-tree files for the Sercomm-manufactured NETGEAR routers. They are now split into two different base-boards, from which the respective model is extended. This partially reverts commit c7842ceaaa27 ("ramips: reorganize DTSI files for Netgear R devices"), which introduced inheritance between two completely unrelated base-boards. Signed-off-by: David Bauer <mail@david-bauer.net>
* ccache: update to 3.7.6DENG Qingfang2019-11-242-3/+3
| | | | | | | | | Update ccache to 3.7.6 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_6 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* tools/quilt: update to 0.66Hannu Nyman2019-11-243-4/+4
| | | | | | | | | Update quilt to version 0.66 Release notes at: http://git.savannah.nongnu.org/cgit/quilt.git/tree/NEWS?id=294006e12 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* libubox: update to latest Git HEADPetr Štetiar2019-11-241-3/+3
| | | | | | | | | | | | | | | | | | | 07413cce72e1 tests: jshn: add more test cases 26586dae43a8 jshn: fix missing usage for -p and -o arguments 8e832a771d3a jshn: fix off by one in jshn_parse_file cb698e35409b jshn: jshn_parse: fix leaks of memory pointed to by 'obj' c42f11cc7c0f jshn: main: fix leak of memory pointed to by 'vars' 93848ec96dc5 jshn: refactor main into smaller pieces 9b6ede0e5312 avl: guard against theoretical null pointer dereference c008294a8323 blobmsg_json: fix possible uninitialized struct member 0003ea9c45cc base64: fix possible null pointer dereference 8baeeea1f52d add assert.h component b0a5cd8a28bf add cram based unit tests 1fefb7c4d7f9 add initial GitLab CI support c955464d7a9b enable extra compiler checks 6228df9de91d iron out all extra compiler warnings Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove ath10k drivers from Archer C7 v1 profileStijn Segers2019-11-241-1/+1
| | | | | | | | | | | Ath10k packages were removed from ar71xx in master in commit 34113999ef43 ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes FS#1743)") but ath79 in master and the 19.07 branch still suffer from the issue. Signed-off-by: Stijn Segers <foss@volatilesystems.org> [commit description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: kernel config: remove runtime optionsPetr Štetiar2019-11-2412-15/+0
| | | | | | | Remove CC_HAS_ASM_GOTO, CC_IS_GCC and GCC_VERSION kernel config options which are set at runtime and which should be ignored now. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel-build: ignore runtime config options during reconfigPetr Štetiar2019-11-241-1/+3
| | | | | | | | | Don't put CC_HAS_ASM_GOTO, IS_GCC, IS_CLANG and GCC_VERSION runtime config options into the kernel configs during reconfiguration as it makes no sense, since these options should be set at runtime. Fixes: FS#2588 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* nghttp2: bump to 1.40.0Hans Dedecker2019-11-231-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 41060943 Bump up version number to 1.40.0, LT revision to 33:0:19 5ae9bb89 Fail fast if huffman decoding context is in failure state bb519154 Merge pull request #1413 from nghttp2/check-authority 77f5487a Add nghttp2_check_authority as public API db9a8f6e Merge pull request #1409 from nghttp2/fix-wrong-stream-close-error-code 6f28a69b Merge pull request #1411 from richard78917/fix_warning 6ce4835e Fix the bug that stream is closed with wrong error code 29042f1c priority_spec::valid(): remove const qualifier from return value d08c4395 Merge pull request #1405 from nghttp2/huffman 5d6964cf Faster huffman decoding 0d855bfc Faster huffman encoding 6f967c6e Fix errors reported by coverity scan b8a43db8 Merge pull request #1394 from wrowe/fix-static-libname 70b62c1a Merge pull request #1393 from wrowe/fix-static-msvcrt 28b1f0b9 Avoid filename collision of static and dynamic lib 1dd966f1 Merge branch 'fix-nghttpx-mruby' fe8946dd nghttpx: Fix bug that mruby is incorrectly shared between backends 72b71a6b Add new flag ENABLE_STATIC_CRT for Windows f8933fe5 nghttpx: Reconnect h1 backend if it lost connection before sending headers 89c33d69 Update neverbleed 7079dc5e Update neverbleed to fix memory leak 5080db84 Revert "nghttpx: Reconnect h1 backend if it lost connection before sending headers" 053c7ac5 nghttpx: Returns 408 if backend timed out before sending headers 8a59ce6d nghttpx: Reconnect h1 backend if it lost connection before sending headers f2fde180 Remove redundant null check before delete 95efb3e1 Don't read too greedily 0a6ce87c Add nghttp2_option_set_max_outbound_ack 2aa79fa9 Bump up LT revision to 32:0:18 3980678d Merge branch 'nghttpx-fix-request-stall' 319d5ab1 nghttpx: Fix request stall 448bbbc3 integration-tests: gofmt e575a2aa Merge pull request #1377 from Aldrog/cmake_systemd 4f7aedc9 cmake: Support building nghttpx with systemd 7a590893 Fix clang-8 warning ee443134 Fix FPE with default backend abef9b90 Fix log-level is not set with cmd-line or configuration file 12a999f0 Bump up version number to 1.40.0-DEV acfb3607 Update manual pages Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 10:25:11 +0000