aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.107Koen Vandeputte2019-03-2210-32/+22
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.164Koen Vandeputte2019-03-224-10/+10
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx6: fix legacy IRQ support (4.19)Koen Vandeputte2019-03-222-0/+50
| | | | | | | | | | | | | | | The PCIe DWC host controller is now using MSI (Message-signaled-interrupts) by default. While ath9k itself does support MSI here, a lot of wlan adapters do not. Avoid non-functioning cards by simply continue to disable MSI for now. This can be done by appending "pci=nomsi" to the boot cmdline. Also an extra fix needs to be backported which avoids MSI initialization which prevented legacy IRQ's init from taking over. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx6: enable PCIe (4.19)Koen Vandeputte2019-03-221-0/+9
| | | | | | | The DWC host controller symbols are now depending on a few others Fixes: ca1b93f038a5 ("imx6: add support for kernel 4.19") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx6: enable crypto acceleration (4.19)Koen Vandeputte2019-03-221-5/+8
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx6: enable crypto accelerationKoen Vandeputte2019-03-221-5/+8
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx6: refresh kernel configsKoen Vandeputte2019-03-222-5/+5
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* glibc: update to latest 2.27 commitHans Dedecker2019-03-221-2/+2
| | | | | | 1ab314d8d3 S390: Mark vx and vxe as important hwcap. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: Add support for Ubiquiti NanoBeam ACTobias Schramm2019-03-225-0/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ar71xx: Add support for Mikrotik RB SXT 2nD r3Xavier Douville2019-03-226-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE with a single 2.4 GHz radio and a 100 Mbps Ethernet port. The device similar to the SXT 2nD r2, but it has SPI NOR flash instead of NAND flash. Hardware -------- CPU: Atheros AR9344 (600 MHz) RAM: 64 MiB FLASH: 16 MiB SPI NOR W25Q128 ETH: 1x 100 Mbps Atheros AG71xx WiFi: 2T2R 802.11b/g/n (ath9k) Power: Passive PoE 8-30 V Installation instructions: 1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a DHCP+TFTP server. 2. Erase the "firmware" partition using the mtd command. This should no longer be required once this patch is merged. 3. Use sysupgrade to install to flash. The file openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin should be used. Signed-off-by: Xavier Douville <github@douville.org>
* build: suppress error output in feeds.mkFlorian Eckert2019-03-221-1/+1
| | | | | | | | | | | If no feed.conf or feeds.conf.default is found on image generation with the imagebuilder we always get the following message "Unable to open feeds configuration at <dir>/scripts/feeds line 48." on std error. To get rid off this needless warning on image generation with the imagebuilder supress the output in feeds.mk. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* netifd: update to latest git HEADHauke Mehrtens2019-03-211-3/+3
| | | | | | | a8cf037 netifd: wireless: Add support for GCMP cipher 34a70b6 netifd: wireless: Add support for 802.11ad Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ubox: update to latest git HEADHauke Mehrtens2019-03-211-3/+3
| | | | | | a782779 kmodloader: increase module name length Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iwinfo: update to latest git HEADHauke Mehrtens2019-03-211-3/+3
| | | | | | | ce1814b iwinfo: Add device ID for Wilocity Wil6210 a8e8275 iwinfo: Add support for 802.11ad Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "valgrind: enable LTO and refresh patches"Hauke Mehrtens2019-03-211-1/+0
| | | | | | | | | This reverts commit 0331770299b1587a96285fd1af33afe6de4ecbb9. With LTO enabled valgridn does not build on MIPS32 any more, deactivate it for now. The patch refresh was not reverted. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* libnftnl: bump to latest versionRosy Song2019-03-211-3/+3
| | | | Signed-off-by: Rosy Song <rosysong@rosinson.com>
* openssl: revert disallowing parallel buildEneas U de Queiroz2019-03-211-1/+1
| | | | | | | Openssl 1.1.0 made wholesale changes to its building system. Apparently, parallel builds are working now. Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
* odhcpd: update to latest git HEAD (FS#2160)Hans Dedecker2019-03-211-3/+3
| | | | | | | | | | 6d23385 dhcpv6: extra syslog tracing b076916 dhcpv6/router: add support for mutiple master interfaces e4a24dc ndp: fix adding proxy neighbor entries 4ca7f7e router: add extra syslog tracing 8318e93 netlink: fix neighbor event handling (FS#2160) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ar71xx: Remove ath10k packages from archer-c7-v1 (fixes FS#1743)Aubrey McIntosh, PhD2019-03-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ath10k_pci driver crashes once loaded and causes boot loops on this device as 5GHz radio QCA9880-AR1A shipped with this router is broken. It's not possible to fix this problem in software, miniPCIe radio has to be replaced. We could've probably fixed crashing of the ath10k driver by reverting following upstream commit: commit 1a7fecb766c83dace747f42b25bbb544b00a0163 Author: Michal Kazior <michal.kazior@tieto.com> Date: Sat Jan 24 12:14:48 2015 +0200 ath10k: reset chip before reading chip_id in probe but it's not worth the effort as it wouldn't make that 5GHz radio usable anyway. So it seems more convenient to just remove the crashing driver and provide bootable images, as I believe, that a router that is working but degraded is better than a router that will not work. For details please see discussions in PR[1] and in FS#1743[2]. 1. https://github.com/openwrt/openwrt/pull/1349 2. https://bugs.openwrt.org/index.php?do=details&task_id=1743 Signed-off-by: Aubrey McIntosh, PhD <aubrey.mcintosh@utexas.edu> [subject and commit message tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: GL.iNet AR300M-nand/nor: correct LAN LEDAndreas Ziegler2019-03-211-1/+1
| | | | | | | | The port labled as "LAN" is eth1. That's different from the -lite variant, where the only existing port eth0 is used as LAN Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
* uboot-fritz4040: fix PKG_MIRROR_HASHChristian Lamparter2019-03-211-1/+1
| | | | | | | The PKG_MIRROR_HASH was for some reason wrong. Fixes: d75db67870fa ("uboot-fritz4040: bump version to 2019-03-03") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* adb: fix missing PKG_MIRROR_HASHChristian Lamparter2019-03-211-0/+1
| | | | | | This package was missing a PKG_MIRROR_HASH value. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: Speed up eeprom read/writeAdrian Schmutzler2019-03-211-2/+2
| | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Rosen Penev <rosenp@gmail.com>
* ramips: Xiaomi MIR3G: detect board name from DTSOzgur Can Leonard2019-03-217-33/+31
| | | | | | | | | | | | | | | | - Former "mir3g" board name becomes "xiaomi,mir3g". - Reorder some entries to maintain alphabetical order. - Change DTS so status LEDs (yellow/red/blue) mimic Xiaomi stock firmware: (Section Indicator) <http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf> <http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf> |Yellow: Update (LED flickering), the launch of the system (steady light); |Blue: during normal operation (steady light); |Red: Safe mode (display flicker), system failure (steady light); Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> [Added link to similar Router 3 model] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ca-certificates: update to version 20190110Josef Schlehofer2019-03-211-4/+3
| | | | | | | | | | - Tested on Turris MOX, OpenWrt master - Removed PKG_BUILD_DIR In build_dir there were two folders ca-certificates and ca-certificates-20190110 and it failed as files were in ca-certificates-20190110 Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
* ipq40xx: add support for EnGenius ENS620EXTSteve Glennon2019-03-2110-4/+550
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M FLASH: 32M SPI NOR W25Q256 ETH: QCA8075 WiFi2: IPQ4018 2T2R 2SS b/g/n WiFi5: IPQ4018 2T2R 2SS n/ac LED: - Power amber - LAN1(PoE) green - LAN2 green - Wi-Fi 2.4GHz green - Wi-Fi 5GHz green BTN: - WPS UART: 115200n8 3.3V J1 VCC(1) - GND(2) - TX(3) - RX(4) Added basic support to get the device up and running for a sysupgrade image only. There is currently no way back to factory firmware, so this is a one-way street to OpenWRT. Install from factory condition is convoluted, and may brick your device: 1) Enable SSH and disable the CLI on the factory device from the web user interface (Management->Advanced) 2) Reboot the device 3) Override the default, limited SSH shell: a) Get into the ssh shell: ssh admin@192.168.1.1 /bin/sh --login b) Change the dropbear script to disable the limited shell. At the empty command prompt type: sed -i '/login_ssh/s/^/#/g’ dropbear /etc/init.d/dropbear restart exit 4) ssh in to a (now-) normal OpenWRT SSH session 5) Flash your built image a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin admin@192.168.1.1:/tmp/ b) ssh admin@192.168.1.1 c) sysupgrade -n /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin 6) After flash completes (it may say "Upgrade failed" followed by "Upgrade completed") and device reboots, log in to newly flashed system. Note you will now need to ssh as root rather than admin. Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> [whitespace fixes, reordered partitions, removed rng node from 4.14, fixed 901-arm-boot-add-dts-files.patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for I-O DATA WN-AC733GR3INAGAKI Hiroshi2019-03-214-3/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification - SoC : MediaTek MT7620A - RAM : DDR2 64 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : MT7620A (SoC), 2T2R - 5 GHz : MT7610E, 1T1R - Ethernet : 10/100/1000 Mbps (RTL8367RB) - LED/key : 4x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from LED side - 57600n8 Flash instruction using factory image: 1. Boot WN-AC733GR3 normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: brcm47xx: Backport fixes for USB on WNDR3400v2 (fixes FS#2170)Petr Štetiar2019-03-202-0/+78
| | | | | | | | | | Eric has reported on OpenWrt's bug tracking system[1], that he's not able to use USB devices on his WNDR3400v2 device after the boot, until he turns on GPIO #21 manually through sysfs. 1. https://bugs.openwrt.org/index.php?do=details&task_id=2170 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: Backport ar933x_uart build fix (fixes FS#2152)Petr Štetiar2019-03-202-0/+198
| | | | | | | | | | | | | | | Andrey has reported on OpenWrt's bug tracking system[1], that he currently can't use ar93xx_uart as pure serial UART without console (CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined), because compilation ends with following error: ar933x_uart.c: In function 'ar933x_uart_console_write': ar933x_uart.c:550:14: error: 'struct uart_port' has no member named 'sysrq' 1. https://bugs.openwrt.org/index.php?do=details&task_id=2152 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* iproute2: update to 5.0.0Deng Qingfang2019-03-207-50/+19
| | | | | | | | | Update iproute2 to 5.0.0 Remove upstream patch 001-tc-fix-undefined-XATTR_SIZE_MAX Alter patch 170-ip_tiny as support for IPX and DECnet is dropped Update patch 010-cake-fwmark to match upstream commit Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* toolchain: Remove binutils 2.29 for ARC targetsDaniel Engberg2019-03-203-18/+0
| | | | | | Remove binutils 2.29 for ARC targets Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* toolchain: Use binutils 2.32 by default for ARCDaniel Engberg2019-03-202-3/+2
| | | | | | Use binutils 2.32 by default for ARC targets Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* toolchain: Remove GCC 7.1 for ARC targetsDaniel Engberg2019-03-2022-981/+0
| | | | | | Remove GCC 7.1 for ARC targets Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* toolchain: Use GCC 8.3.0 by default for ARCDaniel Engberg2019-03-202-1/+2
| | | | | | | | Use GCC 8.3.0 by default for ARC targets Includes a fix by Evgeniy Didin which fixes GCC version selection if DEVEL isn't set Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* kernel: Update arc-add-OWRTDTB-section patch for 4.14Evgeniy Didin2019-03-202-47/+55
| | | | | | | | | | | | | | | | | | | In 4.14.104 commit "e7264579eb80" (ARC: U-boot: check arguments paranoidly) was introduced, which together with 332-arc-add-OWRTDTB-section.patch caused build failure. This commit updates 332-arc-add-OWRTDTB-section.patch. Fixes: http://phase1.builds.openwrt.org/builders/archs38%2Fgeneric/builds/1290 http://phase1.builds.openwrt.org/builders/archs38%2Fgeneric/builds/1269 Signed-off-by: Evgeniy Didin <evgeniy.didin@synopsys.com> [Updated patch for kernel 4.19 in addition] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org>
* mac80211: fix an issue with the TXQ scheduling API and powersave clientsFelix Fietkau2019-03-201-0/+31
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: improve the txq scheduling API to deal with driver buffered packetsFelix Fietkau2019-03-202-3/+108
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: optimize skb resizing to avoid reallocation when using 802.11s + ↵Felix Fietkau2019-03-201-0/+198
| | | | | | batman-adv Signed-off-by: Felix Fietkau <nbd@nbd.name>
* iproute2: add cake fwmark supportRyan Mounce2019-03-202-1/+156
| | | | Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* kmod-sched-cake: bump to latest cakeRyan Mounce2019-03-191-3/+3
| | | | | | | | | | | | | | | | Update the out of tree build of cake. Applicable patches are also in net-next. 057c738 Fix fwmark_shft assignment (again) ca6c162 Add support for storing mark back into conntrack 7ed9b6c Fix off-by-one error when setting fwmark_shft. a4a243a sch_cake: Interpret fwmark parameter as a bitmask 29d707e Simplify logic in cake_select_tin() 8acaaee Permit use of connmarks as tin classifiers 348f186 Make the dual modes fairer 99a7297 compat: Don't lock root qdisc when dumping stats on old kernels Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* kernel: fix compile issue for tda1997x media deviceKoen Vandeputte2019-03-191-0/+48
| | | | | | | | | Building tda1997x fails now unless V4L2_FWNODE is selected: drivers/media/i2c/tda1997x.o: in function `tda1997x_parse_dt' undefined reference to `v4l2_fwnode_endpoint_parse' Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq806x: Enlarge R7500v2 flash - use netgear partitionWang Xin-yu (王昕宇)2019-03-181-7/+1
| | | | | | | | | | | | | | This patch increases available space from 20MB to 86MB. Netgrear OEM firmware contains a 'netgear' partition followed 'ubi', which can be used in openwrt for larger ubi space. (similar to Netgear R7800). original author (notmyrealhandle) tested this on R7500v2 and point that OEM firmware can auto rebuild this partition (if used by openwrt). Author: notmyrealhandle<22336358+notmyrealhandle@users.noreply.github.com> Signed-off-by: Wang Xin-yu (王昕宇) <comicfans44@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [minor touch-ups]
* ath79: align naming of Ubiquiti Nanostation MSven Roederer2019-03-183-5/+6
| | | | | | | | | | | | | Support for the Nanostation M (XW) was added in 40530c8eb with board name "nanostation-m-xw". The current image for the "Nanostation M" uses "nano-m" as the board name. This commit renames it to the full product name as it's used by all other boards. The legacy boardname of the ar71xx target is added via SUPPORTED_DEVICES to ease switching to ath79 target. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [touch-ups on the commit message, removed subject remains] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add #pwm-cells property to MT76x8 dtsMicke Prag2019-03-181-0/+1
| | | | | | | To be able to configure pwms the pwm driver needs to know the number off cells in the "pwms" property. For this platform this is 2. Signed-off-by: Micke Prag <micke.prag@telldus.se>
* usbutils: Update usb.ids to 0.321Daniel Engberg2019-03-181-3/+3
| | | | | | Update usb.ids to 0.321 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ath79: add support for jjPlus JA76PF2Tomasz Maciej Nowak2019-03-186-4/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board. Specification SoC: Atheros AR7161 RAM: 64 MB DDR Flash: 16 MB SPI NOR Ethernet: 2x 10/100/1000 Mbps AR8316 LAN (CN11), WAN/PoE (CN6 - close to power barrel connector, 48 V) MiniPCI: 2x LEDS: 4x, which 3 are GPIO controlled Buttons: 2x GPIO controlled Reset (SW1, closer to ethernet ports), WPS (SW2) Serial: 1x (only RX and TX are wired) baud: 115200, parity: none, flow control: none Currently there is one caveat compared to ar71xx target images as the MAC addresses are random on every reboot. To remedy this one needs to store the WAN MAC address in RedBoot configuration. OpenWrt on first boot, after flashing, will read out the address and assign proper ones to both WAN and LAN ports. It is iportant to NOT keep the old configuration when doing sysupgrade from ar71xx. Upgrading from OpenWrt ar71xx image 1. Connect to serial port, 2. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n <openwrt_sysupgrade_image_name> 3. After writing new image OpenWrt will reboot, now interrupt boot process and enter RedBoot (bootloader) command line by pressing Ctrl+C, 4. Enter following commands (replace variable accordingly), set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_adress> (confirm storing the value by inputting y and pressing Enter) reset 5. Now board should restart and boot OpenWrt with proper MAC addresses. Installation 1. Prepare TFTP server with OpenWrt initramfs image, 2. Connect to WAN ethernet port, 3. Connect to serial port, 4. Power on the board and enter RedBoot (bootloader) command line by pressing Ctrl+C, 5. Enter following commands (replace variables accordingly): set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_address> (confirm storing the value by inputting y and pressing Enter) ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress> load -r -b 0x80060000 <openwrt_initramfs_image_name> exec -c "" 6. Now board should boot OpenWrt initramfs image, 7. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade <openwrt_sysupgrade_image_name> 8. Wait few minutes, after the D2 LED will stop blinking, the board is ready for configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: routerstation: prepare to use sysupgrade-tar format imageTomasz Maciej Nowak2019-03-182-5/+23
| | | | | | | | | | | | | | | | | | In PR [1] introducing initial support for Ubiquiti RouterStation boards, Mathias Kresin suggested to replace the combined sysupgrade image with tarball generated by sysupgrade-tar.sh. This would simplify deployment of sysupgrade as the kernel size (needed to update FIS partition) could be simply calculated on the fly instead of reading value from combined image header. Unfortunately this would break sysupgrade compatibility between ar71xx image and ath79 image. Therefore this commit creates migration path to use new sysuprade image, it adds code to accept both of them at this moment. The plan is to keep it until new stable version is released. Then the image recipe should be changed to new format and compatibility code for old image removed. 1. https://github.com/openwrt/openwrt/pull/1237 Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* lantiq: kernel 4.14: fix usb_phy1 reset status bit in vr9.dtsMartin Schiller2019-03-181-1/+1
| | | | | | The status of USB PHY 1 Reset Domain is also in bit 5 of RST_STAT2. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ath79: qca955x: add wmac migration hotplug eventTomasz Maciej Nowak2019-03-181-0/+32
| | | | | | | | | | | When upgrading from ar71xx target images to ath79 based ones, the integrated wireless interface changes its sysfs path. Therefore the previous enabled wireless interface will be disabled, which can cause false complains about it not working. This commit adds hotplug event which migrates to new path and will keep the wrireless interface enabled after upgrade. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: fix leds description for EnGenius EPG5000Tomasz Maciej Nowak2019-03-181-6/+6
| | | | | | | Align the LEDs deffinition with MACH file present in ar71xx target which has the correct LED functions and colors adescription. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 08:10:17 +0000