| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
| |
This commit adds an append-uboot command to append U-Boot from the
bin-directory.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
| |
This commit alters the TP-Link Archer C50v3 LED settings to use the phy
trigger instead of the netdev one. This way the WiFi status is displayed
even if the wifi interface name is altered.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
| |
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
| |
is needed for at least tplink wr1043nd-v1
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
|
|
|
|
|
|
|
| |
booting will hang most of the times on tl-wr1043nd-v1 without a KERNEL_CMDLINE value
add anything as a placeholder as kernel command line is taken from DTS
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When CONFIG_AUTOREMOVE is enabled, the build system touches an additional
".autoremove" stamp file in the cleaned build directory.
Since the autoremove stamp file is touched after the compile process
completed, it ends up being the most recent file of the package build
directory, causing the timestamp.pl check of depends.mk to erroneously
declare the ".built" and ".prepared" stamp files as stale, triggering
a forced clean-build submake process.
Fix the problem by using the ".built" stamp file as modification time
reference when touching the ".autoremove" stamp file.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0
Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
|
| |
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
|
|
|
| |
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
|
|
| |
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
|
| |
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
|
| |
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
|
|
| |
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In commit 8b9cdebc9c53 ("arc770: mark as source-only") arc770 was marked
as source-only because of iproute2 compile issues.
With uClibc-ng version 1.0.30 issues with iproute2 were fixed.
Lets remove "source-only" for arc770 as soon as uClibc-ng version
will be updated to 1.0.30. Patch for uClibc-ng is here:
https://patchwork.ozlabs.org/patch/917547/
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
uClibc-ng 1.0.28 does not provide PF_VSOCK/AF_VSOCK definitions,
which causes iproute2 v4.16.0 compile errors.
In commit 57f2f80383b5 ("bits/socket.h: add missing defines")
necessary defines were included and iproute2 builds fine.
This commit now is part of uClibc-ng 1.0.30.
Lets update uClibc-ng to latest 1.0.30 version.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.
This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
| |
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
| |
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
| |
Copy and refresh patches and config from 4.9, no more work is need.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As of commit in kernel:
6104c37094 fbcon: Make fbcon a built-time depency for fbdev
framebuffer console is build in into framebuffer module and there's no
standalone fbcon module. Therefore drop the kmod-fbcon and enable
console in kmod-fb. The only targets which use these modules are imx6
and geode, both are on kernel 4.14 so no fallback for other kernels is
introduced.
Being at that this commit also fixes autoload of fbdev for x86.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
|
|
|
|
|
|
|
|
|
|
| |
commit 138c763 ("build: add --force option to gzip in Build/gzip")
added the --force flag to the gzip invocation.
Under environments with busybox gzip (e.g Alpine Linux), this fails
as busybox only recognizes "-f".
Signed-off-by: Mathew McBride <matt@traverse.com.au>
|
|
|
|
| |
Signed-off-by: Rosy Song <rosysong@rosinson.com>
|
|
|
|
| |
Signed-off-by: Rosy Song <rosysong@rosinson.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add initial support for cortex-a72 based Armada DB-88F8040-Modular and
DB-88F7040-Modular development boards.
DB-88F8040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU (up to 2 GHz)
- DDR4 DIMM - 64 bits + ECC
- 2 x 128 Mb SPI NOR flash memory
- 2 x 1G Ethernet port via RGMII (RJ45)
- 2 x SD card ports (4 bit port on CP, 8 bit port on AP)
- 2 SERDES modules with the following interfaces each:
- 2 x SATA Rev 3.0 port (Port1 via SERDES module CON4 (active port), Port0
via SERDES Module CON2 or CON1 (optional port))
- 3 x PCI Express (PCIe) Gen 3.0 (Port2 via SERDES module CON5 (active port),
Port1 via SERDES module CON7 (optional port), Port0 via SERDES module CON6
(optional port))
- 2 x USB3 (USB 2.0 backward compatible) host (via SERDES module CON9 and
CON10)
- 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 1 x MCI interface by two over USB Type C connector
- 4 x serial COM port driven by the 88F8040 UART interface and converted to
USB via FTDI IC
- I2C Master Interface
- CP I2C 2x EEPROM @ Address 0x50 and 0x57
- 1 x I/O Expander @ Address 0x21
- Sample at Reset (SatR) memory device @ Address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions: 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions: 70 mm x 105 mm
DB-88F7040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU
- CPU core operating speed of up to 1.6 GHz for Dual Core, 1.4 GHz for Quad
Core
- DDR4 - 32 bit + ECC on Module - SLM1366-V1 (DB-DDR4-40B-MODULE) 4 GByte
32-bit
- 1 x 128Mb SPI NOR flash memory
- 2 x 1G Ethernet port: 1 over RGMII (RJ45) and 1 over SGMII
- SD card 4 bits port on AP
- eMMc Module on CP
- 1 SERDES Modules with the following interfaces each:
- 1 x SATA Rev 3.0 port (via SERDES module CON4)
- 1 x PCI Express (PCIe) Gen 3.0 (via SERDES module CON5)
- 2 x USB 3.0 (USB 2.0 backward compatible) host (via SERDES module CON9 and
CON10)
- 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 2 x MCi interface by one over USB Type C connector
- 4 x Serial COM port driven by the 88F7040 UA
- RT interface and converted to USB via FTDI IC
- I2C Master Interface
- 2 x EEPROM at address 0x57 and 0x50 in AP and 2 x EEPROM at address 0x57
and 0x50 in CP
- 1 x I/O Expander at address 0x21
- Sample at Reset (SatR) memory device at address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions - 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions - 70 mm x 105 mm
Booting from USB flash drive (dd sdcard image to the flash drive):
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot manually (make sure to set correct dtb file name):
setenv bootargs_root 'root=/dev/sda2 rw rootdelay=2 ip=dhcp'
setenv fdtfile armada-7040-db.dtb
setenv image_name Image
setenv bootcmd 'usb start; ext4load usb 0:1 $kernel_addr $image_name; ext4load usb 0:1 $fdt_addr $fdtfile; setenv bootargs $console $mtdparts $bootargs_root; booti $kernel_addr - $fdt_addr'
saveenv
boot
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add initial support for Marvell Armada cortex-a53 based
DB-88F3720-DDR3-Modular development board.
Specifications:
- Dual core ARMv8 Cortex-A53 CPU (up to 1.0 GHz)
- 4Gb 16-bit DDR3/3L DRAM memory
- 128Mb SPI NOR flash memory
- 8Gb eMMC NAND flash memory
- 1 x SATA Rev 3.0 port
- 1 x PCI Express (PCIe) Gen 2.0 or 1 x mini PCI Express (PCIe) Gen 2.0
- 1 x 1G Ethernet port via RGMII (RJ45)
- 1 x SD card port
- 1 x USB3 (USB2 backward) host\device port via type C connector
- 1 x USB2 host port via type A connector
- 1 x serial COM port driven by the 88F3720 UART interface and converted to
USB via FTDI IC (option to connect the UART DB9 adapter)
- I2C Master Interface:
- 1 x EEPROM @ address 0x57
- 1 x I/O Expanders @ address 0x22
- Sample at Reset (SatR) memory device @ address 0x4C
- RTC clock generator PT7C4337AWE @ address 0x68
- USB3 switch PI5USB30213XEA @ address 0x0D
- ID component of PHY module @ address 0x24
- 1 x JTAG interface for CPU emulator
- 1 x SETM and JTAG debug interface
- 1 x power connector for HDD supply
- 1 x 12V DC jack power connector
- Board dimensions: 150 mm x 179 mm
- LED interface for system status
Booting from SD card:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually:
setenv fdt_name armada-3720-db.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 0; ext4load mmc 0:1 $kernel_addr $image_name;ext4load mmc 0:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr'
saveenv
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
|
|
|
|
|
|
|
|
|
|
| |
Support Add spi-nor chip EN25QH32. JEDEC is 1c7016.
Can't boot issue, new revision hardware is EN25QH32 flash chip.
example, MZK-DP150N (ramips).
https://bugs.openwrt.org/index.php?do=details&task_id=1534
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
|
|
|
|
|
|
|
| |
Added a rule to usb.mk to build usb_f_hid.ko for configfs support
Tested on a Raspberry Pi Zero W
Signed-off-by: Harvey Phillips <xcellerator@gmx.com>
|
|
|
|
|
|
|
|
| |
This now matches what was generated locally on my PC and the file on the
mirror server.
Fixes: 349fe46103359 ("ath10k-firmware: Update QCA988X firmware to the latest version")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
| |
Includes the public usign certificates used by the 18.06.* release builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
| |
Also let the new openwrt-keyring package provide lede-keyring for backwards
compatibility.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* chacha20poly1305: add mips32 implementation
"The OpenWRT Commit" - this significantly speeds up performance on cheap
plastic MIPS routers, and presumably the remaining MIPS32r2 super computers
out there.
* timers: reinitialize state on init
* timers: round up instead of down in slack_time
* timers: remove slack_time
* timers: clear send_keepalive timer on sending handshake response
* timers: no need to clear keepalive in persistent keepalive
Andrew He and I have helped simplify the timers and remove some old warts,
making the whole system a bit easier to analyze.
* tools: fix errno propagation and messages
Error messages are now more coherent.
* device: remove allowedips before individual peers
This avoids an O(n^2) traversal in favor of an O(n) one. Before systems with
many peers would grind when deleting the interface.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
|
|
|
|
|
| |
73edb22 mt76: discard early received packets if not running yet
0b8d1dd mt76: fix beacon timer drift
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
| |
Disable CONFIG_EFI_VARS, since it suffers from sysfs limitation (no
support for variable longer than 1024 bytes).
kmod-fs-efivarfs is the replacement of this, which enables mounting
efivarfs file system and doesn't suffer from 1024 bytes limitation.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use ft_psk_generate_local=1 by default, as it makes everything else fairly
trivial. All of the r0kh/r1kh and key management stuff goes away and hostapd
fairly much does it all for us.
We do need to provide nas_identifier, which can be derived from the BSSID,
and we need to generate a mobility_domain, for which we default to the first
four chars of the md5sum of the SSID.
The complex manual setup should also still work, but the defaults also
now work easily out of the box. Verified by manually running hostapd
(with the autogenerated config) and watching the debug output:
wlan2: STA ac:37:43:a0:a6:ae WPA: FT authentication already completed - do not start 4-way handshake
This was previous submitted to LEDE in
https://github.com/lede-project/source/pull/1382
[dwmw2: Rewrote commit message]
Signed-off-by: Gospod Nassa <devianca@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
|
|
|
|
|
|
| |
e59f925 hardware: add device ids for QCA9984, 88W8887 and 88W8964 radios
2a82f87 nl80211: back out early when receiving FAIL-BUSY reply
77c32f0 nl80211: fix code calculating average signal and rate
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
| |
Drop package/network/services/wireguard/patches/100-portability.patch
Instead pass 'PLATFORM=linux' to make since we are always building FOR
linux.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
BOCCO is a communication robot provided by YUKAI Engineering Inc.
SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Wifi button for WNDR3700 dual band routers has been renamed to "rfkill"
and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE
to support it 'out of the box' without additional tweaking.
Until this patch, button had been sending BTN_2 keycode which was
ignored by default (no action script present). To get expected behaviour
of switching radios on and off, user had to manually rename/link
'rfkill' script to name 'BTN_2' in /etc/rc.button directory.
This patch follows similar changes for other Netgear ar71xx routers,
for example WNR2000v3. It applies cleanly to both latest trunk and 17.01
branch. Tested on WNDR3700v1.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds a image with squashfs as the root filesystem.
A rootfs_data partition will be generated on the first boot
and placed inside the rootfs partition (just after the squashfs
image).
advantages:
- it is possible to migrate from an existing -ext4
installation and back via sysupgrade.
- existing partition layout will not be lost.
- slightly smaller image size.
- support for attendedsysupgrade
disadvantages:
- needs f2fs + tools as well. This is because fs-tools decides on the
blocksize of the sdcard. So either f2fs or ext4 can get choosen as
the rootfs_data filesystem (depends on the size of the root partition).
- rootfs_data is placed into the rootfs partition. This makes
it difficult for tools that expect a /dev/mmc0pX device.
It also makes it difficult for data recovery tools since they
might not expect to find a embedded partition or will be
confused.
For people with existing build configurations: make sure to include mkf2fs
and f2fsck package into the image... Otherwise the new -squashfs image will
boot of a ram-overlay and won't keep the configurations after a reboot.
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: Paul Spooren <spooren@informatik.uni-leipzig.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
|
| |
There is a new APU-model available, APU3. The device is configured in
the same way as the APU1 and APU2, so the same LED/network setup can be
used.
I considered changing the case to pc-engines-apu*, but I chose to follow
the existing pattern and add the full board name.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:
crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx
The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
Not sure how it worked before but ethernet is disabled
by default in ipq4019 dtsi.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches
Dropped upstreamed patches:
522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch
updated patches:
524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch
Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718
Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches
Added new ARM64 symbol: ARM64_ERRATUM_1024718
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
| |
Add needed firmware for newer QCA Rome Bluetooth family.
This enables use of bluetooth with ath3k driver on QCA9377/9378 devices.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
|
|
|
|
|
|
|
| |
- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Mostly whitespace cleanups. Some unneeded code was removed.
MMC init was also moved to the probe function as in
6069bdd
The cleanup commits are over 100, making it hard to do them individually.
Tested on GnuBee PC1 with an SD card being used as swap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
v2: Fixed compile issue with mt7620
|