| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
| |
The value of nvram_tuple_t is allocated in _nvram_realloc,
but it is not freed in _nvram_free.
Signed-off-by: Zhai Zhaoxuan <zhaizhaoxuan@xiaomi.com>
|
|
|
|
|
|
|
|
| |
Add the parent of the sysupgrade script to the list of pids not getting
killed
Signed-off-by: Mat Trudel <mat@geeky.net>
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
| |
The IRQ controller can only set the affinity to a single CPU. Update the
mask in the controller data.
Suggested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
| |
- Remove obsolete patch chunks regarding fixed_freq
- Instead of patching in custom HT40+/- parameters, use the standard
config syntax as much as possible.
- Use fixed_freq for mesh
- Fix issues with disabling obss scan when using fixed_freq on mesh
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Passing the ctrl iface to wpa_supplicant will automatically cause wpa_supplicant
to send "STOP_AP" messages to the hostapd. This breaks the AP interfaces.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The beacon_int is currently set explicitly for hostapd and when LEDE uses
iw to join and IBSS/mesh. But it was not done when wpa_supplicant was used
to join an encrypted IBSS or mesh.
This configuration is required when an AP interface is configured together
with an mesh interface. The beacon_int= line must therefore be re-added to
the wpa_supplicant config. The value is retrieved from the the global
variable.
Fixes: 1a16cb9c67f0 ("mac80211, hostapd: always explicitly set beacon interval")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [rebase]
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The wpa_supplicant code for IBSS allows to set the mcast rate. It is
recommended to increase this value from 1 or 6 Mbit/s to something higher
when using a mesh protocol on top which uses the multicast packet loss as
indicator for the link quality.
This setting was unfortunately not applied for mesh mode. But it would be
beneficial when wpa_supplicant would behave similar to IBSS mode and set
this argument during mesh join like authsae already does. At least it is
helpful for companies/projects which are currently switching to 802.11s
(without mesh_fwding and with mesh_ttl set to 1) as replacement for IBSS
because newer drivers seem to support 802.11s but not IBSS anymore.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Simon Wunderlich <simon.wunderlich@openmesh.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [refresh]
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
TP-Link TL-WR802N v1 and v2 are set up with almost same configuration in
the mach-files. Merge the mach-files of these devices.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM
- 16 MB flash
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
|
|
|
|
|
|
|
|
| |
The TL-WA901ND v5 has the same hardware as v4, although the PCB has
a different layout. Installation from factory is done via TFTP.
(rename -factory image to wa901ndv4_tp_recovery.bin for tftp)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port
This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.
Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.
Installation
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
|
|
|
|
|
|
|
| |
The Ubiquiti UniFi APs just have eth0. Until now, the setup script fell
through to the default case and configured the (not present) eth1 as
WAN with DHCP.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD
Specifications:
- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)
This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.
Installation:
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
TP-Link TL-WR810N v2 is a compact Wi-Fi router with two Ethernet ports.
Specification:
- QCA9533 (650 MHz)
- 32 MB RAM
- 8 MB Flash
- 300 Mbps Wi-Fi 2.4 GHz
- 2x 10/100 Mbps Ethernet (eth0, eth1)
- UART on testpads on PCB
- 1x LED (GPIO-controlled)
- 1x reset/WPS button
- 1x slide-switch with 2 GPIO inputs
Flash instructions:
- Flash as regular firmware update in Web UI
- Default: 192.168.0.254 / admin / admin
- Select *-factory.bin
When holding reset button during power-up, U-Boot requests a file
'wr810nv1_tp_recovery.bin' from TFTP server at 192.168.0.66
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
|
|
|
| |
If codes do not match, it is impossible to flash from the stock
firmware.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.
Short specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
UniElec U7628-01 is a router platform board based on MediaTek MT7628AN.
The device has the following specifications:
- MT7628AN (580MHz)
- 64/128/256 MB of RAM (DDR2)
- 8/16 MB of flash (SPI NOR)
- 5x 10/100 Mbps Ethernet (MT7628 built-in switch)
- 1x 2T2R 2.4 GHz Wi-Fi (MT7628)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 2.0 port
- 7x single-color LEDs (GPIO-controlled)
- 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe)
- 1x reset button
- 1x UART header (4-pins)
- 1x SDXC/GPIO header (10-pins, connected with microSD slot)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slot (tested with modem and Wi-Fi card)
- miniSIM slot
- sysupgrade
- reset button
- USB 2.0 port*
Due to a missing driver (MMC over GPIO) this is not supported:
- microSD card reader
* Warning:
USB buses in miniPCIe and regular A-type socket are connected together,
without any proper analog switch or USB HUB.
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 128MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
SDXC/GPIO header (J3):
1. SDXC_D3 / I2C_SCLK
2. SDXC_D2 / I2C_SD
3. SDXC_D1 / I2S_DI
4. SDXC_D0 / I2S_WS
5. SDXC_CMD / I2S_CLK
6. SDXC_CLK / GPIO0
7. SDXC_CD / UART_RXD1
8. UART_TXD1
9. 3V3
10. GND
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 128/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
UniElec U7621-06 is a router platform board based on MediaTek MT7621AT.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256/512 MB of RAM (DDR3)
- 8/16/32/64 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x ASMedia ASM1061 (for mSATA and SATA)
- 2x miniPCIe slots (PCIe bus only)
- 1x mSATA slot (with USB 2.0 bus for modem)
- 1x SATA
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 3.0
- 12x LEDs (3 GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x FPC connector for LEDs (20-pin, 0.5 mm pitch)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slots (tested with Wi-Fi cards)
- mSATA slot (tested with modem and mSATA drive)
- miniSIM slot
- sysupgrade
- reset button
- microSD slot
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 256MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt7621-u7621-06-256M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (top row, left to right):
- LED_WWAN# (connected with pin 42 in LTE/mSATA slot)
- Power (connected directly to 3V3)
- CTS2_N (GPIO10, configured as "status" LED)
- TXD2 (GPIO11, configured as "led4", without default trigger)
- RXD2 (GPIO12, configured as "led5", without default trigger)
- LED_WLAN# (connected with pin 44 in wifi0 slot)
LEDs list (bottom row, left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 256/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
2. The manufacturer offers five different wireless cards with MediaTek
chipsets, based on MT76x2, MT7603 and MT7615. Images of the board all
show that the miniPCIe slots are dedicated to specific Wi-Fi cards.
However, the slots are generic.
3. All boards we got access to had the same EEPROM content. The default
firmware reads the Ethernet MAC from offset 0xe000 in factory partition.
This offset only contains 0xffs, so a random MAC will be generated on
every boot of the router. There is a valid MAC stored at offset 0xe006
and this MAC is shown as the WAN MAC in the bootloader. However, it is
the same on all boards we have checked. Based on information provided
by the vendor, all boards sold in small quantities are considered more
as samples for development purposes.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This increases kernel partition size and fixes rootfs (file-system)
partition size on TP-Link RE450 v1. Also, while we are at it, switch
from statically defined kernel and rootfs partitions in kernel cmdline
to "tplink-fw" mtd splitter.
Fixes: FS#1072.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch increases kernel partition size and re-enables image
generation for below TP-Link boards:
- archer-c58-v1
- archer-c60-v1
- tl-wr902ac-v1
- tl-wr942n-v1
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[commit message and title reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
| |
They are inspired and compatible with the original and mjn3's trx tool.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
| |
There is no need to allocate buffer as big as the whole image in order
to calculate CRC32. It's enough to use small buffer and just read file
content block by block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
| |
This requires changing this helper to accept initial/current CRC32
value as argument but it allows dropping duplicated (complex?) code
calculating the CRC32.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
|
| |
Remove multicast routing firewall rules when the igmpproxy is stopped by
triggering a firewall config change.
Keeping the firewall open from the wan for igmp and udp multicast is not
desired when the igmpproxy service is inactive.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
| |
This patch is to enable CONFIG_CRYPTO_ARC4 in kernel 4.9
which is a dependency for mac80211 package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
| |
Fix swapped arguments "mac" and "ip" when calling function
"ubus_event_bcast".
Signed-off-by: Jaroslav Safka <devel@safka.org>
|
|
|
|
|
| |
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (PKG_RELEASE increase)
|
|
|
|
|
|
| |
a0231be8fbc61 sys: fix memory leak in packagelist
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
| |
When a library is using fortify-packages GCC will complain about
"error: format not a string literal, argument types not checked".
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
|
|
|
|
|
|
| |
don't set no-ssl3-method when CONFIG_OPENSSL_WITH_SSL3 di disabled otherwise the compile breaks with this error:
../libssl.so: undefined reference to `SSLv3_client_method'
Fixes CVE: CVE-2017-3735, CVE-2017-3736
Signed-off-by: Peter Wagner <tripolar@gmx.at>
|
|
|
|
|
|
| |
4e483312b0216 sys: add packagelist method
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
| |
Check if the compiler defines __linux__, instead of assuming that the
host OS is the same as the target OS.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
It builds a kernel module, so its build dir should be target specific
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
7c9aa7c service: add data within the service itself
e2b819a service: fix calls to blobmsg_parse()
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
| |
Use the same approach than the service_triggers for the service_data.
Signed-off-by: Pierre Lebleu <pme.lebleu@gmail.com>
|
|
|
|
|
|
|
|
| |
There was a typo in module.mk for pfe module autoload.
This patch is to fix this and remove useless rc.local
which was for loading pfe module.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
| |
Added a README for layerscape targets build and deployment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
|
| |
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
| |
This patch is to enlarge ext4 rootfs size to 30MB.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic
This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
|
| |
This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enabled CONFIG_ARCH_DMA_ADDR_T_64BIT in kernel to
resolve below call trace when ls1046ardb 32-bit
started up kernel.
[ 0.142141] Bman ver:0a02,02,01
[ 0.145326] ------------[ cut here ]------------
[ 0.149969] WARNING: CPU: 0 PID: 1 at arch/arm/mm/ioremap.c:303 __arm_ioremap_pfn_caller+0x1ac/0x1d8
[ 0.159152] Modules linked in:
[ 0.162216] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.51-g9c76e024 #2
[ 0.169036] Hardware name: Generic DT based system
[ 0.173853] [<c02236a4>] (unwind_backtrace) from [<c021ed94>] (show_stack+0x10/0x14)
[ 0.181638] [<c021ed94>] (show_stack) from [<c04d2d38>] (dump_stack+0x98/0xac)
[ 0.188899] [<c04d2d38>] (dump_stack) from [<c0245bcc>] (__warn+0xe4/0x100)
[ 0.195896] [<c0245bcc>] (__warn) from [<c0245c98>] (warn_slowpath_null+0x20/0x28)
[ 0.203504] [<c0245c98>] (warn_slowpath_null) from [<c0229e24>] (__arm_ioremap_pfn_caller+0x1ac/0x1d8)
[ 0.212861] [<c0229e24>] (__arm_ioremap_pfn_caller) from [<c0229f0c>] (ioremap_cache+0x20/0x28)
[ 0.221608] [<c0229f0c>] (ioremap_cache) from [<c105e390>] (parse_mem_property.part.3+0x18/0x50)
[ 0.230441] [<c105e390>] (parse_mem_property.part.3) from [<c105e6dc>] (qman_init_early+0x314/0x334)
[ 0.239623] [<c105e6dc>] (qman_init_early) from [<c0201a24>] (do_one_initcall+0xb4/0x168)
[ 0.247844] [<c0201a24>] (do_one_initcall) from [<c1000e84>] (kernel_init_freeable+0x1d8/0x280)
[ 0.256590] [<c1000e84>] (kernel_init_freeable) from [<c0adbcfc>] (kernel_init+0x8/0x114)
[ 0.264812] [<c0adbcfc>] (kernel_init) from [<c021bb28>] (ret_from_fork+0x14/0x2c)
[ 0.272423] ---[ end trace 39aaeef329e2a0a2 ]---
[ 0.277058] qman-fqd addr 0xfb000000 size 0x800000
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
|
| |
Some new options were introduced by kernel patches.
And some options should be removed/added.
The config-4.9 should be updated accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
| |
Updated kernel patches to align layerscape kernel
with latest LSDK linux (LSDK-17.09-update-103017-V4.9 tag).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
| |
For ls1012ardb, pfe should be stopped before starting up
kernel.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
| |
Updated u-boot to LSDK-1709-update-103017 tag.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|