aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix ZyXEL Keenetic Omni/Omni II GPIOsAlexey Belyaev2017-04-252-6/+22
| | | | | | | Each GPIO bank has only 24 gpios. Use and enable the correct banks for GPIOs > 24. Signed-off-by: Alexey Belyaev <spider@spider.vc>
* ramips: fix ZyXEL Keenetic Omni switch configAlexey Belyaev2017-04-252-2/+2
| | | | | | | The wan port is connected to switch port 0. Fix the mediatek,portmap as well as the default switch config. Signed-off-by: Alexey Belyaev <spider@spider.vc>
* lantiq: DGN3500: make switch LEDs blink on activityKevin Darbyshire-Bryant2017-04-251-0/+15
| | | | | | | | | | | | | | | | | Make switch port LEDs blink on activity as they do with stock firmware. The u-boot loader sets suitable values in the LED control register that unfortunately get blown away by the linux switch driver init. Restore that value by using driver 'initvals'. 0x0431 is the led control register, the value 0x0960. Each nybble represents each LED's mode (LED3,2,1,0) in this case OFF, 1000LINK+Activity, 100/10LINK+Activity, OFF. Only LED1&2 are physically present. Enabling the blinkenlights exposed the fact that an RRCP packet was being emitted by the switch on all ports every second. Further initvals copied from stock firmware's u-boot driver disabled this 'feature'. Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* generic: rtl8366rb: add support for initvals from DTSKevin Darbyshire-Bryant2017-04-251-0/+25
| | | | | | | | | Allow per-device initvals in the DTS file for rlt8366rb switches. Shamelessly copies 30494598f891fc4436a49eca55fc31d03c087841 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* netifd: return error status in reload_serviceHans Dedecker2017-04-241-1/+4
| | | | | | | | Based on a patch by Alexandru Ardelean. netifd ubus reload call returns the actual reload error status; return error status as well in reload_service Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: update to git HEAD versionHans Dedecker2017-04-241-3/+3
| | | | | | | | | 11cb9cf ubus: add interface method to trigger renew event 4375d1b system-linux: allow "throw" route type 5fbd904 netifd: propagate error code on netifd_reload() 6e0acec interface-ip: fix device name for IPv6 link-local DNS server Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* odhcpd: update to git HEAD versionHans Dedecker2017-04-241-3/+3
| | | | | | | 570069d ubus: rework dumping IPv6 and IPv4 leases 4e579c4 dhcpv6-ia: simplify logic to write statefile and dhcpv6 logging Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* omap: rework image generation and profilesAlexander Couzens2017-04-246-44/+104
| | | | | | | | | Migrate to new image generation and introduce sdcard generation (based on sunxi). Profile now generated via image/Makefile instead of profiles/ directory. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* package/uboot-omap: add am335x_boneblackAlexander Couzens2017-04-241-1/+6
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* package/uboot-omap: add default uEnv to boot via mmc cardAlexander Couzens2017-04-242-0/+10
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* package/uboot-omap: re-introduce patches dropped by update to v2017.01Alexander Couzens2017-04-243-0/+85
| | | | | | | The beagleboard doesn't boot with Thumb enabled, but without Thumb the SPL (first stage bootloader) is too big to fit into SRAM. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* package/uboot-omap: install image to STAGING_DIR_IMAGEAlexander Couzens2017-04-241-0/+5
| | | | | | to use them later by image/Makefile to create full working sdcard images Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* package/uboot-omap: assign BUILD_DEVICES most boardsAlexander Couzens2017-04-241-1/+3
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* omap: correct CPU_TYPE: omaps are cortext-a8Alexander Couzens2017-04-241-1/+1
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* omap/Kconfig: refresh by oldconfigAlexander Couzens2017-04-241-2/+3
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* omap/Kconfig: add usb optionsAlexander Couzens2017-04-241-5/+5
| | | | | | including phy and required dma options Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* omap/Kconfig: enable SMPAlexander Couzens2017-04-241-3/+15
| | | | | | the pandaboard is a multicore omap Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* omap/Kconfig: add omap2plus_cpufreqAlexander Couzens2017-04-241-1/+1
| | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* mac80211: rt2x00: add incomplete support for external PA on MT7620Daniel Golle2017-04-241-0/+125
| | | | | | | | | | | | | | Do as the vendor driver does -- however, some devices apparently patched support for external PA into the driver similar to how it was done on Rt3352, using EEPROM_NIC_CONF1 rather than EEPROM_NIC_CONF2, hence we check for both fields. Somehow the vendor driver also no longer offers the option of only one of the TX paths having an external PA (which was probably to weird to ever be implemented in practise, though it doesn't seem like a particularly bad idea to me). Do the same in rt2x00 and enable support for external PA on both TX paths whenever it is set for TX0 in EEPROM. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: rt2x00: reorder patches and prepare for MT7620 external PADaniel Golle2017-04-245-0/+128
| | | | | | | | | Import change to make external PA capability consistent with the vendor driver instead of having the logic inverted. While at it, apply patches in the same order as they got merged upstream. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: fix sysupgrade board detectionJohn Crispin2017-04-242-5/+10
| | | | | | | boardnames were changed with the recent target update. the sysupgrade board detection was not updated properly. Signed-off-by: John Crispin <john@phrozen.org>
* include/image.mk: allow passing a compat string to the NAND image templateJohn Crispin2017-04-241-5/+6
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: add support for the NAND-ePHY boardJohn Crispin2017-04-244-2/+538
| | | | | | This is the same as the NAND board but gmac1 is wired to an external phy. Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: add DSA multi cpu port supportJohn Crispin2017-04-242-0/+351
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: fix support for gmac1 using external PHYJohn Crispin2017-04-244-2/+115
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq8064: fix dwc3-of-simple module unloading for Netgear R7500Thomas Reifferscheid2017-04-242-14/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without patch unloading the dwc3-of-simple module went stuck after successfully removing hcd.1 during the hcd.0 removal: root@LEDE:/# rmmod dwc3-of-simple [ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 21.391931] usb usb4: USB disconnect, device number 1 [ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 21.406685] usb usb3: USB disconnect, device number 1 [ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 21.422521] usb usb2: USB disconnect, device number 1 followed by nothing. Sometimes a stall CPU was detected, or a kernel panic, or a reboot occurred after a couple of minutes. At the same time unloading the dwc3 module followed by dwc3-of-simple module was working repeatedly. root@LEDE:/# rmmod dwc3 [ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 53.827412] usb usb4: USB disconnect, device number 1 [ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 53.842314] usb usb3: USB disconnect, device number 1 [ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 53.857882] usb usb2: USB disconnect, device number 1 [ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 53.873696] usb usb1: USB disconnect, device number 1 [ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered root@LEDE:/# rmmod dwc3-of-simple root@LEDE:/# For the non-working case, the code was stuck in a readl() in http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91 because http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126 was disabling the wrong clocks when removing hcd.1 (it was disabling the clock of hcd.0). That's why the readl() went stuck when removing hcd.0 The patch however addresses the clock assignment from the Netgear R7500 dts file and backs off the previous attempt. Now unloading and repeated module loading is working just fine. root@LEDE:/# rmmod dwc3-of-simple [ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 24.089765] usb usb4: USB disconnect, device number 1 [ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 24.104522] usb usb3: USB disconnect, device number 1 [ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 24.120396] usb usb2: USB disconnect, device number 1 [ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 24.135948] usb usb1: USB disconnect, device number 1 [ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered root@LEDE:/# Fixes: dwc3-of-simple module unloading for Netgear R7500 Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
* ipq8064: Fix dwc3 module unloadingThomas Reifferscheid2017-04-241-3/+11
| | | | | | | | | | The patch follows the qualcomm code comments setting SSUSB_CTRL_TEST_POWERDOWN to 0x1 and is testing and clearing the bit during USB superspeed PHY init. According to Andy Gross it needs to be BIT(26). Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org> Acked-by: Andy Gross <andy.gross@linaro.org>
* kernel: use skb_cow_head() to deal with cloned skbsÁlvaro Fernández Rojas2017-04-2314-0/+534
| | | | | | | | | | | We need to ensure there is enough headroom to push extra header, but we also need to check if we are allowed to change headers. skb_cow_head() is the proper helper to deal with this. Fixes Ethernet<->WiFi bridge for Raspberry Pi and probably other devices. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* scripts/qemustart: initial versionYousong Zhou2017-04-231-0/+281
| | | | | | | | The script can be used to quickly spin up QEMU virtual machines with lan and wan network. Please read the initial part of the script for instructions about how to configure host machine Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* armvirt: merge arm64 as subtarget 64Yousong Zhou2017-04-2312-345/+165
| | | | | | | | | | | | | | | | | | | | Original armvirt target is now subtarget 32. Other than that the built result should remain the same as before Besides old features already available with arm64, the new armvirt/64 subtarget will also have those features originally enabled for armvirt/32 with commit 44ecfc2 ("armvirt: new target") - pl011, uart - pl031, rtc - pl061, gpio - pci-host-generic - virtio_{mmio,pci,net,blk,scsi,9p,console,balloon} - smp with NR_CPUS=4 - cpu-hotplug - ext4 - DEBUG_BUGVERBOSE for debug purposes Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* build: fix aarch64 default cpu selectionYousong Zhou2017-04-231-2/+2
| | | | | | | | | | | | | | | | Not sure since when the issue emerged, but according to the current doc of gcc and as, armv8-a is intended as argument of -march The change will affect at the moment arm64 and layerscape/64b Below is the relevant error messages when building toolchain Assembler messages: Error: unknown cpu `armv8-a' Error: unrecognized option -mcpu=armv8-a /home/yousong/git-repo/lede-project/lede/build_dir/toolchain-aarch64_armv8-a_gcc-5.4.0_musl/gcc-5.4.0/libgcc/libgcc2.c:1:0: error: unknown value 'armv8-a' for -mcpu Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* iptables: fix wrong depends for nftables support (FS#707)Ansuel Smith2017-04-221-1/+1
| | | | | | | The dep for the nftables support was wrong, if someone actually enable that option gain a compilation error. This fix this problem. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ar71xx: fix minor syntax error in /lib/upgrade/platform.shMatthias Schiffer2017-04-221-1/+1
| | | | | | | Fix a '==' that should be a '=' in a test condition. Busybox fortunately doesn't care. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: update DEVICE_PACKAGES for Ubiquiti EdgeRouter XMatthias Schiffer2017-04-221-1/+1
| | | | | | Fixes removal of unneeded kernel modules with per-device rootfs. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: add former board names to PSG1218 variantsDaniel Golle2017-04-211-0/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* busybox: fix build of nslookup_lede applet without IPv6 (#728)Jo-Philipp Wich2017-04-211-9/+33
| | | | | | | | | Protect any IPv6 related with appropriate guards to fix compilation with disabled IPv6 support in Busybox. Fixes #728. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* lantiq: improve DGN3500 LED definitionsKevin Darbyshire-Bryant2017-04-212-9/+65
| | | | | | | | | | | | | | | | Add red:internet led on gpio 30 previously claimed as missing. Wifi led was claimed as blue however there are no blue leds on the board at all. Actually there are two wifi leds, green & amber so add definitions for those. Make the newly discovered green wifi led gpio 14 the default. There is no amber power led on this board. The mention of the amber power led in the manual means power red and power green at the same time. Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk> [removed unnecessary aliases, add migration script] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: dont replace the board nameMathias Kresin2017-04-216-45/+88
| | | | | | | | | | Use fixed led names and add each board variant instead of manipulating the board name. It makes the ramips board name function less different to the one used in other targets and allows to merge them with a common function. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add former used board names to metadataMathias Kresin2017-04-212-0/+8
| | | | | | | | | We need to keep the former used (unmodified) boardname in the metadata. Otherwise an upgrade from an board using the old boardname will be refused. Fixes: a75ce960ac1b ("ramips: use different board names for variants") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: rename PSG1218 to match labelDaniel Golle2017-04-218-30/+30
| | | | | | | | Fix previous commit to be less ambigous: PSG1218 rev.A = 5 ports, external PA, heatsinks PSG1218 rev.B = 4 ports, internal PA, no heatsinks Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: split Phicomm PSG1218 and PSG1218K2CDaniel Golle2017-04-219-84/+145
| | | | | | | | | PSG1218 got only 4 Ethernet ports and WAN on port 3 while PSG1218K2C got 5 Ethernet ports and WAN on port 4 Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm53xx: enable Northstar thermal driverRafał Miłecki2017-04-202-0/+10
| | | | | | | It allows monitoring CPU temp and will shutdown system on critical value. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport DT patches for serial, thermal and MDIORafał Miłecki2017-04-2010-2/+576
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* generic: mtd: backport mx25u25635f stateless 4b supportMathias Kresin2017-04-192-1/+30
| | | | | | | | | Use the stateless 4-byte op codes for this flash chip to fix reboot hangs on SoCs expecting the flash chip in 3-byte mode. Fixes: FS#179 Signed-off-by: Mathias Kresin <dev@kresin.me>
* mac80211: rt2800: fix mt7620 E2 channel registersTomislav Požega2017-04-181-0/+41
| | | | | | | | update RF register 47 and 54 values according to vendor driver Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: moved changes into a separate patch]
* mac80211: rt2800: fix mt7620 vco calibration registersTomislav Požega2017-04-181-0/+50
| | | | | | | | | | Use register values from init LNA function instead of the ones from restore LNA function. Apply register values based on rx path configuration. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: moved changes into a separate patch]
* mac80211: fix kconfig recursive dependency warningFelix Fietkau2017-04-181-2/+1
| | | | | | | | | | | | | Make brcmfmac depend on !TARGET_uml. Technically, brcmfmac could be built for uml because only SDIO support won't work on that target. However, selectively avoiding the dependency propagation of !TARGET_uml from kmod-mmc to avoid including a reference to BRCMFMAC_SDIO doesn't work. In practice, brcmfmac is completely useless on uml, so let's just disable it there. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: rt2x00: fix MT7620 LNA gain and VCO-after-ALCDaniel Golle2017-04-172-0/+88
| | | | | | | This should fix issues with bad RX as well as AP not coming up and/or scanning failing. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* dnsmasq: fix uninitialized varname in init-scriptBastian Bittorf2017-04-171-1/+1
| | | | | | | | | minor/cosmetic: fixes the following misleading message: root@box:~ /etc/init.d/dnsmasq restart sh: out of range Signed-off-by: Bastian Bittorf <bb@npl.de>
* Revert "mvebu: remove linux 4.4 support"Felix Fietkau2017-04-1779-0/+14294
| | | | | | | | This reverts commit 51397d7d95d9f5e210a5557f65de1fa21e6f5921. There are some unresolved random crashes on WRT1900AC v1 that still need to be sorted out Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 14:21:27 +0000