aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: fix LED config for DIR-869 A1Florian Beier2017-11-031-7/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the LED configuration for the D-Link DIR-869 A1. In order to support the device I probed around using an initramfs image for the UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them. GPIO 16 set to low meant that the color was white while pulling it to high made the color change to orange. The past code was written based upon these findings. However, running a flashed image I now discovered that GPIO 15 controls the orange LEDs while GPIO 16 controls the white ones and that both are active when low. This means that the GPIOs were inverted and one active_low was set wrong which this patch fixes. Behavior of the LED front after this patch is applied: cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness 0 -> white LEDs are OFF 255 -> white LEDs are ON cat /sys/devices/platform/leds-gpio/leds/d-link:orange:status/brightness 0 -> orange LEDs are OFF 255 -> orange LEDs are ON If the brightness of both is set to 255 the LED front will be white. If the brightness of both is set to 0 the LED front will be off. Signed-off-by: Florian Beier <beier.florian@gmail.com>
* base-files: add interval option to netdev LED trigger configurationEdmunt Pienkowsky2017-11-032-1/+2
| | | | | | Add an uci option to set the interval parameter of the netdev trigger. Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
* ar71xx: wzr-hp-ag300h: drop unused wmac led_pin settingsMathias Kresin2017-11-031-3/+0
| | | | | | | | | The GPIOs are used for defined LEDs and therefore are ignored/unset in the ath9k driver since 192f0a3db859. The wireless led led trigger is added in userspace since e20965811db6, which makes the ap9x_pci_setup_wmac_led_pin() superfluous. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-kirkwood: update to 2017.09Paul Wassi2017-11-039-101/+160
| | | | | | | | | | Upgrade uboot-kirkwood to upstream release 2017.09 Catch up with upstream and move configuration options from simple defines to Kconfig, as otherwise dependencies would not be resolved and code would not compile. Tested-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: mach-rbspi: fix 74x164 supportThibaut VARENE2017-11-031-0/+1
| | | | | | | | | | | | | The platform data was missing the num_registers element which is now mandatory in linux 4.9 Without this patch, the gpio probing would fail with: gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines Fixes: #1106 Tested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ipq806x: nbg6817: sync MAC addresses to the upstream valuesStefan Lippers-Hollmann2017-11-032-2/+5
| | | | | | | | | | | | | | | | | | | | | | The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses are stored in the ART partition and the generated MAC addresses for the wlan interfaces alternate randomly between 12:34:56:78:90:12 and 00:03:7f:12:34:56. interface new/ OEM MAC old MAC wlan-2.4g (phy1): ethaddr undefined wlan-5g (phy0): ethaddr + 1 undefined lan : ethaddr + 2 ethaddr wan : ethaddr + 3 ethaddr + 1 This patch defines stable MAC addresses for the wlan interfaces for the first time instead of generating them at random. The previously defined values for lan/ wan are changed to follow the settings of the OEM firmware. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: nbg6817: add kmod-fs-ext4 to device packagesStefan Lippers-Hollmann2017-11-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split into the readonly squashfs and ext4 for the overlay. This adds the required package to the device packages to allow mounting the overlay by default. /dev/root on /rom type squashfs (ro,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,noatime) sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime) tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime) /dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered) overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work) tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000) debugfs on /sys/kernel/debug type debugfs (rw,noatime) mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect) Before this commit, the ext4 based overlayfs could not be mounted, which left only the tmpfs based/ volatile emergency overlay in place. Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768 Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ltq-atm: add missing dependency to kmod-ltq-adsl-*-meiMathias Kresin2017-11-031-2/+2
| | | | | | | | | | | | | Commit 2e496876c60 fixed the generation of the depends line for external kernel modules which makes it possible for the build system to automatically detect this missing dependency. This fixes the packaging of kmod-ltq-atm for the ar9, xway and xway-legacy subtarget. Fixes: FS#1124 Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: fix another regression in append-dtb fixFelix Fietkau2017-11-031-0/+4
| | | | | | Filter out duplicate generated code for the same dts files Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: fix regression in append-dtb fixFelix Fietkau2017-11-031-4/+3
| | | | | | | Strip whitespace from DTS directory Put the dependency earlier in the chain to avoid make errors Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uclient: update to the latest version, fixes fetch of multiple filesFelix Fietkau2017-11-021-3/+3
| | | | | | 4b87d83 uclient-fetch: fix overloading of output_file variable Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: fix dns and domain variables pollution in dhcp.scriptTero Jänkä2017-11-022-5/+7
| | | | | | | Unmodified dns and domain variables could be needed in user script (/etc/udhcpc.user). Signed-off-by: Tero Jänkä <tero.janka@gmail.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (cleanup)
* build: allow calling append-dtb from image build commandsFelix Fietkau2017-11-022-2/+17
| | | | | | | | | | | | mpc85xx uses this for firmware image files, since the dtb data is not directly part of the kernel image. This causes build failures in the image builder. Fix this by adding a separate build step that runs this call earlier, reusing the generated file for any calls from kernel or image build commands. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* gcc: remove support for libgcj/javaFelix Fietkau2017-11-022-13/+2
| | | | | | It has been removed in gcc 7 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* include/toplevel.mk: Add xconfig targetAlif M. Ahmad2017-11-021-0/+9
| | | | | | | | | | Add xconfig target to include/toplevel.mk, so that ``make xconfig`` can be invoked from $TOPDIR to use Qt based configuration tool to prepare .config file. The qconf related sources are taken from linux 4.9.13 archive. Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
* scripts/config: add qconf files to .gitignoreAlif M. Ahmad2017-11-021-0/+6
| | | | | | | | | This commit adds qconf related files to .gitignore. The files to be tracked are qconf.cc, qconf.h, and images.c. The files to be ignored are qconf*.o, qconf*, qconf.moc, and .tmp_qtcheck. Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
* scripts/config: Add qconf target to MakefileAlif M. Ahmad2017-11-021-0/+56
| | | | | | | | | | qconf is kconfig UI utilizing QT toolkit. This makes it possible to use graphical interface interaction to configure LEDE build target. This commit adds qconf target to ./script/config/Makefile to be used by toplevel ``make xconfig`` later. Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
* scripts/config: add -DKBUILD_NO_NLS to CXXFLAGSFelix Fietkau2017-11-021-0/+1
| | | | | | Preparation for adding C++ code which needs the same flag Signed-off-by: Felix Fietkau <nbd@nbd.name>
* scripts/config: import qconfAlif M. Ahmad2017-11-023-0/+2526
| | | | | | Import qconf.cc, qconf.h, and images.c from linux kernel 4.9.13 archive. Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
* ramips: add support for switching between 3-byte and 4-byte addressing on ↵Felix Fietkau2017-11-022-9/+224
| | | | | | | | | | | | | | | w25q256 flash On some devices the flash chip needs to be in 3-byte addressing mode during reboot, otherwise the boot loader will fail to start. This mode however does not allow regular reads/writes onto the upper 16M half. W25Q256 has separate read commands for reading from >16M, however it does not have any separate write commands. This patch changes the code to leave the chip in 3-byte mode most of the time and only switch during erase/write cycles that go to >16M addresses. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* nghttp2: switch to release tarballHans Dedecker2017-11-011-7/+5
| | | | | | | Switch from git to xz release tarball as there's no good reason to keep using git when release tarballs are provided. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* openssl: Enable assembler optimizations for aarch64Baptiste Jonglez2017-10-312-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OpenSSL is built with the generic linux settings for most targets, including aarch64. These generic settings are designed for 32-bit CPU and provide no assembler optmization: this is widely suboptimal for aarch64. This patch simply switches to the aarch64 settings that are already available in OpenSSL. Here is the output of "openssl speed" before the optimization, with "(...)" representing build flags that didn't change: OpenSSL 1.0.2l 25 May 2017 options:bn(64,32) rc4(ptr,char) des(idx,cisc,2,int) aes(partial) blowfish(ptr) compiler: aarch64-openwrt-linux-musl-gcc (...) And after this patch, OpenSSL uses 64 bit mode and assembler optimizations: OpenSSL 1.0.2l 25 May 2017 options:bn(64,64) rc4(ptr,char) des(idx,cisc,2,int) aes(partial) blowfish(ptr) compiler: aarch64-openwrt-linux-musl-gcc (...) -DSHA1_ASM -DSHA256_ASM -DSHA512_ASM Here are some benchmarks on a pine64+ running latest LEDE master r5142-20d363aed3: before# openssl speed sha aes blowfish The 'numbers' are in 1000s of bytes per second processed. type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes sha1 3918.89k 9982.43k 19148.03k 24933.03k 27325.78k sha256 4604.51k 10240.64k 17472.51k 21355.18k 22801.07k sha512 3662.19k 14539.41k 21443.16k 29544.11k 33177.60k blowfish cbc 16266.63k 16940.86k 17176.92k 17237.33k 17252.35k aes-128 cbc 19712.95k 21447.40k 22091.09k 22258.35k 22304.09k aes-192 cbc 17680.12k 19064.47k 19572.14k 19703.13k 19737.26k aes-256 cbc 15986.67k 17132.48k 17537.28k 17657.17k 17689.26k after# openssl speed sha aes blowfish type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes sha1 6770.87k 26172.80k 86878.38k 205649.58k 345978.20k sha256 20913.93k 74663.85k 184658.18k 290891.09k 351032.66k sha512 7633.10k 30110.14k 50083.24k 71883.43k 82485.25k blowfish cbc 16224.93k 16933.55k 17173.76k 17234.94k 17252.35k aes-128 cbc 19425.74k 21193.31k 22065.74k 22304.77k 22380.54k aes-192 cbc 17452.29k 18883.84k 19536.90k 19741.70k 19800.06k aes-256 cbc 15815.89k 17003.01k 17530.03k 17695.40k 17746.60k For some reason AES and blowfish do not benefit, but SHA performance improves between 1.7x and 15x. SHA256 clearly benefits the most from the optimization (4.5x on small blocks, 15x on large blocks!). When using EVP (with "openssl speed -evp <algo>"): # Before, EVP mode type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes sha1 3824.46k 10049.66k 19170.56k 24947.03k 27325.78k sha256 3368.33k 8511.15k 16061.44k 20772.52k 22721.88k sha512 2845.23k 11381.57k 19467.69k 28512.26k 33008.30k bf-cbc 15146.74k 16623.83k 17092.01k 17211.39k 17249.62k aes-128-cbc 17873.03k 20870.61k 21933.65k 22216.36k 22301.35k aes-192-cbc 16184.18k 18607.15k 19447.13k 19670.02k 19737.26k aes-256-cbc 14774.06k 16757.25k 17457.58k 17639.42k 17686.53k # After, EVP mode type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes sha1 7056.97k 27142.10k 89515.86k 209155.41k 347419.99k sha256 7745.70k 29750.06k 95341.48k 211001.69k 332376.75k sha512 4550.47k 18086.06k 39997.10k 65880.75k 81431.21k bf-cbc 15129.20k 16619.03k 17090.56k 17212.76k 17246.89k aes-128-cbc 99619.74k 269032.34k 450214.23k 567353.00k 613933.06k aes-192-cbc 93180.74k 231017.79k 361766.66k 433671.51k 461731.16k aes-256-cbc 89343.23k 209858.58k 310160.04k 362234.88k 380878.85k Blowfish does not seem to have assembler optimization at all, and SHA still benefits (between 1.6x and 14.5x) but is generally slower than in non-EVP mode. However, AES performance is improved between 5.5x and 27.5x, which is really impressive! For aes-128-cbc on large blocks, a core i7-6600U @2.60GHz is only twice as fast... Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* acx-mac80211: allow compilation on 4.9Jonas Gorski2017-10-291-1/+1
| | | | | | acx-mac80211 compiles fine with 4.9, so no reason to not allow it. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar7: add kernel 4.9 supportJonas Gorski2017-10-2915-0/+1067
| | | | | | Compile and run tested on WAG354Gv1. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar7: drop unused 4.1 supportJonas Gorski2017-10-2914-995/+0
| | | | | | Kernel 4.1 isn't support anymore anyway. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar7: unbreak serial consoleJonas Gorski2017-10-293-33/+53
| | | | | | | | | Serial output was broken since 3.16 for shared uarts between kernel and login. Fix this by adding a fix sent upstream. While at it, drop a useless patch that adds duplicate code. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar7: remove gpio character deviceJonas Gorski2017-10-295-216/+0
| | | | | | | There are no obvious users, and any out of tree users should convert to one of the generic APIs. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar7-atm: fix function signatures with expected onesJonas Gorski2017-10-292-0/+126
| | | | | | | Newer kernels treat differing signatures an error, not just a warning, so fix the signatures to match. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar7-atm: fixup proc fixesJonas Gorski2017-10-296-24/+90
| | | | | | | They were incomplete, so fix them to properly update the function signatures to what is expected. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar7-atm: drop LINUX_VERSION testsJonas Gorski2017-10-2914-339/+199
| | | | | | | | | Minimum supported kernel is 3.18, so we don't need to test for anything older. In addition, the API hasn't changed since then, so we don't need to check for any kernel version at all. This helps to keeps the amount of changes more managable. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* curl: bump to 7.56.1Hans Dedecker2017-10-293-41/+5
| | | | | | | | | | | Refresh patches Remove 320-curl-confopts.m4-fix-disable-threaded-resolver.patch as integrated upstream See https://curl.haxx.se/changes.html for the bugfixes in 7.56.0 and 7.56.1 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* nghttp2: bump to 1.27.0Hans Dedecker2017-10-291-3/+3
| | | | | | | | | | | | Changes in v1.27.0 : build: Fixed accidental compiler flags concatenation for MSVC (Patch from LazyHamster) (GH-1029) build: Reduce libxml2 version requirement to 2.6.26 (Patch from Mike Lothian) (GH-1020) asio: Support for Windows / MinGW (Patch from Daniel Evers) (GH-1027) h2load: Print out h2 header fields with --verbose option (GH-1015) nghttpx: Send non-final response to HTTP/1.1 or HTTP/2 client only (GH-1016) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ltq-atm: Add missing dependency to kmod-ltq-adsl-ase-meiHauke Mehrtens2017-10-291-1/+1
| | | | | | | | | Commit 2e496876c60 fixed the generation of the depends line for external kernel modules which makes it possible for the build system to automatically detect this missing dependency. This fixes the build bot build of the lantiq/aes target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* build: use KERNEL_MAKE_FLAGS for kernel file compilationsKarl Vogel2017-10-2920-46/+22
| | | | | | | The build system already defines KERNEL_CROSS which defaults to TARGET_CROSS. Make use of this variable for kernel makefiles. Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
* adb: fix package descriptionMatt Mets2017-10-291-1/+1
| | | | Signed-off-by: Matt Mets <matt@blinkinlabs.com>
* layerscape: reverse changes to ndo_get_stats64Mathew McBride2017-10-299-2365/+650
| | | | | | | | | | | | The NXP LSDK kernel backported changes for interface ndo_get_stats64 functions from mainline, this causes a compile error with backports/mac80211, which expects the original 4.9 defintion. As reversing the ndo_get_stats64 change signifcantly reduces the size of patch 601, the patches that were aggregated into it have been disaggregated. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: Remove netfilter and LZ4 config symbolsMathew McBride2017-10-292-164/+0
| | | | | | | | These conflict with the kmod packages (such as nf-netlink) Signed-off-by: Mathew McBride <matt@traverse.com.au> [Add same changes for arm8_32b subtarget and refresh config] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* arc770: mark as source-onlyHans Dedecker2017-10-281-1/+1
| | | | | | | | | Mark target arc770 as source-only as it has package compile issues (e.g. iproute2) due to the usage of uClibc. As a prerequisite to be included in future releases the arc770 target needs to switch either to glibc or musl. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* build: actually fix the creation of PKG_INFO_DIRJonas Gorski2017-10-281-1/+1
| | | | | | | | The creation was accidentally moved to the wrong hook, fix it by moving it to the pre hook. Fixes: e5e5c3f5fd38 ("build: ensure PKG_INFO_DIR exists before trying to use it") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* build: ensure PKG_INFO_DIR exists before trying to use itJonas Gorski2017-10-281-0/+1
| | | | | | | | | | | PKG_INFO_DIR is only created at the finish step of the first package build, but kernel modules now use it at the start. Doing a parallel build could cause a kernel module to be the first package, breaking the build. Fix this by ensuring the directory exists. Fixes: 2e496876c60c ("kernel: collect module symvers for external modules") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mwlwifi: switch to AutoProbeJonas Gorski2017-10-271-1/+1
| | | | | | | Now that we have working module dependency generation, we can switch to AutoProbe and let modprobe handle loading required modules. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mt76: switch to AutoProbeJonas Gorski2017-10-271-3/+2
| | | | | | | Now that we have working module dependency generation, we can switch to AutoProbe and let modprobe handle loading required modules. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mac80211: ath10k: switch to AutoProbeJonas Gorski2017-10-271-1/+1
| | | | | | | Now that we have working module dependency generation, we can switch to AutoProbe and let modprobe handle loading required modules. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* broadcom-wl: switch to AutoProbeJonas Gorski2017-10-271-1/+1
| | | | | | | Now that we have working module dependency generation, we can switch to AutoProbe and let modprobe handle loading required modules. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* broadcom-wl: reorder kmod build and pass EXTRA_VERSIONSJonas Gorski2017-10-271-5/+7
| | | | | | | | | Reoder the build to build the glue module first and pass the glue module's Module.symvers to the wl driver builds. This allows modpost to properly store a wl_glue dependency in the driver. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* broadcom-wl: define module directoriesJonas Gorski2017-10-271-0/+2
| | | | | | | Define the module subdirs so our build system properly picks up the Module.symvers. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ath10k-ct: switch to AutoProbeJonas Gorski2017-10-271-1/+1
| | | | | | | Now that we have working module dependency generation, we can switch to AutoProbe and let modprobe handle loading required modules. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ath10k-ct: define module directoriesJonas Gorski2017-10-271-0/+1
| | | | | | | Define the module subdir so our buildsystem properly picks up the Module.symvers. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* acx-mac80211: drop PKG_BUILD_DEPENDSJonas Gorski2017-10-271-1/+0
| | | | | | | We already have a DEPENDS on mac80211, which should be enough to ensure headers are available before build. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* acx-mac80211: switch to AutoProbeJonas Gorski2017-10-271-1/+1
| | | | | | | Now that we have working module dependency generation, we can switch to AutoProbe and let modprobe handle loading required modules. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 01:05:44 +0000